Ferroelectric-relaxor behavior of (Na0.5K0.5)NbO3-based ceramics

We report that ferroelectric-relaxor behavior is induced by doping of SrO and TiO₂, or BaO and TiO₂ into classic ferroelectric (Na_0.5K_0.5)NbO₃. It is found that [(Na_0.5K_0.5)_0.9Sr_0.1](Nb_0.9Ti_0.1)O₃ ceramics exhibit a pronounced ferroelectric-relaxor behavior, comparable to that of [(Na_0.5K_0.5)_0.9Ba_0.1](Nb_0.9Ti_0.1)O₃ ceramics. Our results indicate that the relaxor behavior is closely related to the appearance of micropolar regions in these systems. The relaxor behavior should arise from the dynamic response of micropolar clusters. Raman spectra of [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics measured in the wavenumber range from 100 to 1200 cm⁻¹ confirm that the first order scattering is dominant in phonon bands should result from both short-range ordered region (micropolar regions) and disordered matrix. The frequency dependence of dielectric permittivity measurements show that the relaxor behavior of SrO and TiO₂, or BaO and TiO₂ doped (Na_0.5K_0.5)NbO₃ ceramics is not a Debye type in the radio frequency range.     

Crystalline structural phase boundaries in (K,Na,Li)NbO 3 ceramics

Lead-free (K_xNa_1−x)_1−yLi_yNbO₃ ceramics (with x=0.50, y=0–0.08 and x=0.30–0.70, y=0.06, respectively) were synthesized using the conventional solid-state reaction technique. Compositional influences of K, Na and Li constituents on microstructures, crystalline structures, dielectric and piezoelectric properties were investigated. It has been known that microstructures change largely with the alkali constituents and that there exist three orthorhombic-tetragonal phase boundaries at room temperature. One occurs in (K_0.50Na_0.50)_1−yLi_yNbO₃ ceramics at y=0.05–0.06, which corresponds to the previously reported morphotropic phase boundary (MPB). The other two appear in (K_xNa_1−x)_0.94Li_0.06NbO₃ ceramics near x=0.40 and x=0.60, respectively. (K_0.50Na_0.50)_0.935Li_0.065NbO₃ and (K_0.45Na_0.55)_0.94Li_0.06NbO₃ ceramics show high piezoelectric properties with the d₃₃ values over 200 pC/N and the k_p values around 45% at room temperature. It is thought that the observed high piezoelectric properties are largely affected by the temperature-driven orthorhombic-tetragonal phase transition.     

Relationship between phase structure and electrical properties of (K0.5Na0.5)NbO3-LiTaO3 lead-free ceramics

Lead-free piezoelectric ceramics of (1−x)K_0.5Na_0.5NbO₃-xLiTaO₃ (KNN-LT) system have been investigated in this work. X-ray diffraction, Raman spectra measurements, DSC (Differential Scanning Calorimetric), and dielectric constant versus temperature provide direct evidence that the phase transition temperature between tetragonal and orthorhombic shift to lower temperature with the increasing of LT content. The KNN-0.05LT ceramics exhibit the highest high-field d₃₃ up to 220 pm/V. At the same time, we also investigated the relationship between phase structure and electric properties, showing that the orthorhombic phase presents better piezoelectric temperature stabilities than the tetragonal phase. The result may provide a new way for KNN-based lead-free ceramics.     

Dielectric and piezoelectric properties of lead-free (Na0.5K0.5)NbO3-SrTiO3 ceramics

In this article, we report successful preparation of dense [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ (x=0.005-0.100) ceramics by ordinary sintering in air. The dependence of phase structure on doping content of SrO and TiO₂ has been determined by the X-ray diffraction technique. It was found that the crystal structure changed from orthorhombic to tetragonal at x≈0.040. Dielectric study revealed that the dielectric relaxor behavior was induced by doping of SrO and TiO₂ into (Na_0.5K_0.5)NbO₃. The samples in the composition range from x=0.005 to 0.020 exhibited excellent electrical properties, piezoelectric constant of electromechanical planar and thickness coupling coefficients of k_p=26.6-32.5% and k_t=39.8-43.8%. The results show that the [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics are one of the promising lead-free materials for electromechanical transducer applications.     

Impedance spectroscopy and piezoresponse force microscopy analysis of lead-free (1 − x) K0.5Na0.5NbO3 − xLiNbO3 ceramics

(1 ? x) K_0.5Na_0.5NbO₃ ? xLiNbO₃ (where x = 0.0, 5.0, 5.5, 6.0, and 6.5 wt.%) (KNLN) perovskite structured ferroelectric ceramics were prepared by the solid-state reaction method. X-ray diffraction patterns indicate that single phase was formed for pure KNN while a small amount of second phase (K₆Li₄Nb₁₀O₃₀, ～3%) was present in LN doped KNN ceramics. Phase analysis indicated the change in the crystal structure from orthorhombic to tetragonal with increase in LN content. The electrical behavior of the ceramics was studied by impedance spectroscopy technique in the high temperature range. Impedance analysis was performed using an equivalent circuit model. The impedance response in pure KNN and KNLN ceramics could be deconvoluted into two contributions, associated with the bulk (grains) and the grain boundaries. Activation energies for conductivity were found to be strongly frequency dependent. The activation energy obtained from dielectric relaxation data was attributed to oxygen vacancies. From PFM we found that the composition with 6.5 wt.% LN displays stronger piezocontrast as compared to pure KNN implying an evidence of a pronounced piezoelectric coefficient.     

Dielectric and impedance measurements on (1−x)Ba(Fe1/2Ta1/2)O3-xBa(Zn1/3Ta2/3)O3 ceramics

In this work, ((1−x)Ba(Fe_1/2Ta_1/2)O₃-xBa(Zn_1/3Ta_2/3)O₃), ((1−x)BFT-xBZT) ceramics with x = 0.00–0.12 were synthesized by the solid–state reaction method. X-ray diffraction data revealed that both the powders and ceramics were of a pure-phase cubic perovskite structure. All ceramics showed large dielectric constants. For the x = 0.12 sample, a very high dielectric constant (>20,600) was observed. A lowering in the dielectric loss compared to pure BFT ceramics was observed with the BZT addition. The impedance measurements indicated that BZT has a strong effect on the bulk grain and grain boundary resistance of BFT ceramics. These results are in agreement with the measured dielectric properties. Based on dielectric and impedance results, (1−x)BFT-xBZT ceramics could be of great interest for high performance dielectric materials applications due their giant dielectric constant behavior.     

Na1−xLixNbO3 ceramics studied by X-ray diffraction, dielectric, pyroelectric, piezoelectric and Raman spectroscopy

Na_1−xLi_xNbO₃ ceramics with composition 0.05≤x≤0.30 were prepared by solid-state reaction method and sintered in the temperature range 1100-1150 °C. These ceramics were characterised by X-ray diffraction as well as dielectric permittivity measurements and Raman spectroscopy. Dielectric properties of ceramics belonging to the whole composition domain were investigated in a broad range of temperatures from 300 to 750 K and frequencies from 0.1 to 200 kHz. The Rietveld refinement powder X-ray diffraction analysis showed that these ceramics have a single phase of perovskite structure with orthorhombic symmetry for x≤0.15 and two phases coexistence of rhombohedral and orthorhombic above x=0.20. The evolution of the permittivity as a function of temperature and frequency showed that these ceramics Na_1−xLi_xNbO₃ with composition 0.05≤x≤0.15 present the classical ferroelectric character and the phase transition temperature T_C increases as x content increases. The polarisation state was checked by pyroelectric and piezoelectric measurements. For x=0.05, the piezoelectric coefficient d₃₁ is of 2pC/N. The evolution of the Raman spectra was studied as a function of temperatures and compositions. The results of the Raman spectroscopy study confirm our dielectric measurements, and they indicate clearly the transition from the polar ferroelectric phase to the non-polar paraelectric one.     

Properties of non-stoichiometric 0.935(K0.5+xNa0.5+x)NbO3-0.065LiSbO3 lead-free piezoelectric ceramics

0.935(K_0.5+xNa_0.5+x)NbO₃-0.065LiSbO₃ lead-free piezoelectric ceramics were prepared by normal sintering, and their piezoelectric and dielectric properties were investigated by varying the compensating amount x of alkaline elements (Na and K) addition. It was found that the crystal structure changed from tetragonal to orthorhombic with increasing x from −0.010 to 0.010. An MPB was tailored by optimizing the alkaline elements contents. Enhanced electrical and electromechanical responses of d₃₃=253 pC/N, k_p=0.47, k_t=0.45 and tanδ=0.027 were obtained in the ceramics with x=0.005. These excellent piezoelectric and electromechanical properties indicate that this system may be an attractive lead-free material for a wide range of electro-mechanical transducer applications.     

Phase diagram of (1−x%)(0.89Bi0.5Na0.5TiO3–0.06BaTiO3–0.05K0.5Na0.5NbO3)–x%MnO2 lead-free anti-ferroelectric ceramics

A phase diagram for the lead-free ceramics in the (1?x%)(0.89Bi_0.5Na_0.5TiO₃–0.06BaTiO₃–0.05K_0.5Na_0.5NbO₃)–x%MnO₂ (BNBKN-x%Mn) binary system is constructed for the first time based on the ferroelectric and dielectric measurements. The ferroelectric behaviors under different temperatures suggest that the ceramics are basically of relaxor anti-ferroelectric nature near room temperature. The temperature dependent dielectric properties show that when the addition of MnO₂ increases, the relaxor anti-ferroelectric phase can be stabilized to be close to the Curie point, which corresponds to a relaxor anti-ferroelectric to paraelectric phase transition.     

Effects of A-site non-stoichiometry on the structural and electrical properties of 0.96K0.5Na0.5NbO3- 0.04LiSbO3 lead-free piezoelectric ceramics

Effects of A-site non-stoichiometry on the structural and electrical properties of 0.96K0.5+xNa0.5+xNbO3- 0.04LiSbO3 lead-free piezoelectric ceramics were examined for 0 ≤ x ≤ 0.02. The piezoelectric coefficients exhibited a maximum, d33 = 187 pC/N at x = 0.0075, coinciding with the maximum of the grain size and the apparent density at x = 0.0075. The apparent density and the piezoelectric coefficients decreased with increasing x at higher x which was likely due to the crystal geometrical distortion of 0.96K0.5+xNa0.5+xNbO3-0.04LiSbO3. In addition, super-large grains were found and this may be due to liquid phase sintering. Excess (K++Na+) attracted a sum of space charges to keep the charge neutral, resulting in charge leakage during the course of ceramic polarization, influencing the piezoelectric and ferroelectric properties. These findings are of importance for guiding the design of K0.5Na0.5NbO3-based lead-free ceramics with enhanced electrical properties.     

Effects of composition on phase structure and electrical properties of (K0.5Na0.5)0.90Li0.06Sr0.02Nb(1−x)SbxO3 ceramics

Lead-free (K_0.5Na_0.5)_0.90Li_0.06Sr_0.02Nb_(1−x)Sb_xO₃ (KNLSN-Sb_x) ceramics were synthesized by ordinary sintering technique. The compositional dependence of phase structure and electrical properties of the ceramics was systematically investigated. All samples possessed pure perovskite structure, showing room temperature symmetries of orthorhombic at x<0.01, coexistence of orthorhombic and tetragonal phases at x=0.01, and tetragonal at 0.02≤x≤0.05. The temperature of the polymorphic phase transition (PPT) was shifted to lower temperature and dielectric relaxor behavior was induced by increasing Sb content. The samples near the coexistence region (x=0.01) exhibited enhanced electrical properties: d₃₃∼145 pC/N, k_p∼38% and P_r∼20.4 μC/cm².     

Microstructure and electrical properties of Bi0.5Na0.5TiO3–Bi0.5K0.5TiO3–LiNbO3 lead-free piezoelectric ceramics

Lead-free piezoelectric ceramics of (1?x?y)Bi_0.5Na_0.5TiO₃–xBi_0.5K_0.5TiO₃–yLiNbO₃ (BNT–BKT–LN-x/y) have been fabricated by a conventional solid-state reaction method, and their microstructure and electrical properties have been investigated. The results of X-ray diffraction (XRD) measurement show that K⁺, Li⁺ and Nb⁵⁺ diffuse into the Bi_0.5Na_0.5TiO₃ lattices to form a solid solution with a pure perovskite structure. The BKT and LN addition has no remarkable effect on the crystal structure. However, a significant change in grain size took place. Simultaneously, with increasing amount of LN, the temperature for a ferroelectric–antiferroelectric phase transition is clearly reduced. The temperature dependence of dielectric properties suggests that the ceramics have diffuse-type phase transition characteristics. The piezoelectric constant d₃₃ and the electromechanical coupling factor k_p of the ceramics attain maximum values of 195 pC/N and 0.336 at x=0.18 and y=0.01.     

Microstructure and piezoelectric properties of Bi0.5(Na0.82K0.18)0.5TiO3−NaSbO3 ceramics

Lead-free piezoelectric ceramics (1−x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃−xNaSbO₃ have been prepared by a conventional ceramics technique, and their microstructure and electrical properties have been investigated. The addition of NaSbO₃ has no remarkable effect on the crystal structure within the studied doping content; however, an obvious change in microstructure took place. With increase in NaSbO₃ content, the temperature from a ferroelectric to antiferroelectric phase transition increases, and the temperature for a transition from antiferroelectric phases to paraelectric phases changes insignificantly. Simultaneously, the temperature range between the rhombohedral phase transition point and the Curie temperature point becomes smaller. The piezoelectric properties significantly increase with increase in NaSbO₃ content and the piezoelectric constant and electromechanical coupling factor attain maximum values of d₃₃=160 pC/N and k_p=0.333 at x=0.01. The results indicate that (1−x)Bi_0.5(Na_0.82K_0.18)_0.5TiO₃−xNaSbO₃ ceramic is a promising lead-free piezoelectric candidate material.     

Structural and dielectric anomaly in Na1−XKxNbO3, at x = 0.315

Structural and dielectric properties of sodium-potassium niobate (Na_1?x K_xNbO₃) (0.250?≤?x?≤?0.350) ceramics, prepared by the solid-state reaction method were investigated. Observed dielectric properties show a strong compositional dependence, at all the measured temperatures (from room temperature to 150°C) and frequencies (from 1 to 1000?kHz). In the prepared compositions, the lowest values of dielectric permittivity, loss tangent and electrical conductivity were found, and an anomaly in the shifting pattern of X-ray diffraction (XRD) peaks and change in the slope of a/c vs. x plot were observed at x?=?0.315. The observed structural and dielectric anomaly gives a morphotropic phase boundary-like indication, in Na_1?xK_xNbO₃ system, at x?=?0.315.     

Study on the formation during the production of lead-free piezoceramics at the morphotropic phase boundary

Because of the environmental concerns, the manufacture of ceramics based on lead titanate zirconate [Pb(Zr_1−xTi_x)O₃−PZT] has been condemned because of the lead toxicity. In this context, the electromechanical properties of sodium, potassium and lithium niobate [(Na_0.5−x/2K_0.5−x/2Li_x)NbO₃−NKLN] at the morphotropic phase boundary granted these materials the position of most suitable candidate to replace PZT. However, the production of these ceramics is rather critical mainly because of a natural tendency of forming secondary phases. To help with the studies of the synthesis of this lead-free piezoceramic, this work presents an evaluation of the crystallization of the (Na_0.47K_0.47Li_0.06)NbO₃ phase by solid-state reactions. TG-DTA, XRD, dilatometric and ferroelectric hysteresis analyses indicated that a secondary phase (K₃Li₂Nb₅O₁₅) crystallizes at temperatures above 850 C and also during the sintering of the powders compacts at 1080 C. To prevent the formation of this phase, the addition of Na₂Nb₂O₆.nH₂O microfibers obtained through a microwave hydrothermal synthesis was performed in the sintering process. After to this addition, the suppression of the K₃Li₂Nb₅O₁₅ phase occurred and an increase of the NKLN electrical properties was then obtained.     

Modified structure and electrical properties of BSZT doped KNN hybrid ceramic

Lead free (1?x)(K_0.5Na_0.5)NbO₃–x(Ba_0.9Sr_0.1)(Zr_0.1Ti_0.9)O₃ [(1?x)KNN–xBSZT] (x=0,0.02,0.04 and 0.06) ceramic were synthesized by a solid-state reaction method and the effects of BSZT doping on the electrical properties of KNN have been studied. X-ray diffraction (XRD) indicates that all the samples have single-phase perovskite structure and addition of BSZT forms a morphotropic phase boundary (MPB) i.e. the coexistence of orthorhombic and tetragonal phase in the region 0.02≤x≤0.04. Field emission scanning electron microscopy (FESEM) indicates the reduction in the grain size with the addition of BSZT. Small broadening in the dielectric peak arises at higher concentration of BSZT. The value of remnant polarization at x=0.04 is found to be higher than any other value of x except x=0 and also results in enhancement of dielectric constant at room temperature. Thereby it makes it useful for application at room temperature.     

Structure, electrical properties and temperature characteristics of?Bi0.5Na0.5TiO3–Bi0.5K0.5TiO3–Bi0.5Li0.5TiO3 lead-free piezoelectric ceramics

(1−x−y)Bi_0.5Na_0.5TiO₃–xBi_0.5K_0.5TiO₃– yBi_0.5Li_0.5TiO₃ lead-free piezoelectric ceramics have been prepared by an ordinary sintering technique, and their structure, electrical properties, and temperature characteristics have been studied systematically. The ceramics can be well-sintered at 1050–1150 °C. The increase in K⁺ concentration decreases the grain-growth rate and promotes the formation of grains with a cubic shape, while the addition of Li⁺ decreases greatly the sintering temperature and assists in the densification of BNT-based ceramics. The results of XRD diffraction show that K⁺ and Li⁺ diffuse into the Bi_0.5Na_0.5TiO₃ lattices to form a solid solution with a pure perovskite structure. As x increases from 0.05 to 0.50, the ceramics transform gradually from rhombohedral phase to tetragonal phase and consequently a morphotropic phase boundary (MPB) is formed at 0.15≤x≤0.25. The concentration y of Li⁺ has no obvious influence on the crystal structure of the ceramics. Compared with pure Bi_0.5Na_0.5TiO₃, the partial substitution of K⁺ and Li⁺ for Na⁺ lowers greatly the coercive field E _c and increases the remanent polarization P _r of the ceramics. Because of the MPB, lower E _c and large P _r, the piezoelectricity of the ceramics is improved significantly. For the ceramics with the compositions near the MPB (x=0.15–0.25 and y=0.05–0.10), the piezoelectric properties become optimum: piezoelectric coefficient d ₃₃=147–231 pC/N and planar electromechanical coupling factor k _P=20.2–41.0%. In addition, the ceramics exhibit relaxor characteristic, which probably results from the cation disordering in the 12-fold coordination sites. The depolarization temperature T _d shows a strong dependence on the concentration x of K⁺ and reaches the lowest values at the MPB. The temperature dependences of the ferroelectric and dielectric properties at high temperatures may imply that the ceramics may contain both the polar and non-polar regions at temperatures above T _d.     

Ferroelectric relaxor properties of (1 − x)K0.5Na0.5NbO3–xBa0.5Ca0.5TiO3 ceramics

The Ba_0.5Ca_0.5TiO₃ (BCT) composition dependent dielectric and structural properties of (1?x)K_0.5Na_0.5NbO₃–xBa_0.5Ca_0.5TiO₃ powders were investigated. Room temperature x-ray diffraction revealed the powder structure to transform from orthorhombic to cubic with increasing BCT composition. The frequency dependent dielectric constant measurements revealed a shift in the temperature of the maximum dielectric constant for at frequencies, suggesting that the system exhibits ferroelectric relaxor behavior. The system containing 15% BCT showed the closest calculated Curie–Weiss exponent to 2, which the exponent for a relaxor ferroelectric.     

Piezoelectric and ferroelectric properties of [(K0.4725Na0.4725)Li0.055]NbO3–(Ag0.5Li0.5)TaO3 lead‐free ceramics

New lead‐free piezoelectric (1 – x)[(K_0.4725Na_0.4725)Li_0.055]NbO₃– x (Ag_0.5Li_0.5)TaO₃ [(1 – x)KNNL–x ALT] ceramics were prepared by conventional sintering. Piezoelectric and ferroelectric properties and Curie temperature of the ceramics were studied. The (1 – x)KNNL–x ALT (x = 0.04) ceramics exhibit good properties (d₃₃ ～ 252 pC/N, k_p ～ 41%, T_C ～ 471 °C, T_o–t = 47 °C, P_r = 33.1 μC/cm², E_c = 10.6 kV/cm). These results show that (1 – x)KNNL–x ALT (x = 0.04) ceramic is a promising lead‐free piezoelectric material for high temperature application. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Piezoelectric properties of [Li0.03(K0.48Na0.52)0.97](Nb0.97Sb0.03)O3-(Ba0.85Ca0.15)(Ti0.90Zr0.10)O3 lead-free piezoelectric ceramics

[Li_0.03(K_0.48Na_0.52)_0.97](Nb_0.97Sb_0.03)O₃-(Ba_0.85Ca_0.15)(Ti_0.90Zr_0.10)O₃ [(1−x)LKNNS-xBCTZ] lead-free piezoelectric ceramics were prepared by the conventional solid state method, and effects of BCTZ content on the piezoelectric properties of LKNNS ceramics were mainly investigated. A stable solid solution has been formed between LKNNS and BCTZ, and a morphotropic phase boundary of (1−x)LKNNS-xBCTZ ceramics is identified in the range of 0 < x ≤ 0.02. The Curie temperature of (1−x)LKNNS-xBCTZ ceramics decreases with increasing BCTZ content. A higher ?_r value and a lower tan δ value are demonstrated for the (1−x)LKNNS-xBCTZ ceramic with x = 0.02. The (1−x)LKNNS-xBCTZ ceramic with x = 0.02 has an enhanced electrical behavior of d₃₃ ∼ 237 pC/N, k_p ∼ 48.6%, ?_r ∼ 1451, tan δ ∼ 0.037, and T_c ∼ 335 °C. As a result, (1−x)LKNNS-xBCTZ ceramics are promising candidate materials for the field of lead-free piezoelectric materials.