NMR and FT-IR Investigation of Spinel LiMn2O4 Cathode Prepared by the Tartaric Acid Gel Process

The structure of the lithium manganese tartrate precursor and the synthesis mechanism of LiMn₂O₄ were investigated by FT-IR, NMR, TG/DSC, and XRD in this study. The results of FT-IR and ⁷Li and ¹³C NMR measurements revealed that lithium ions bond with carboxylic acid ligands and the O–H stretching modes of tartaric acid. Manganese ion bonds only with carboxylic acid. Lithium and manganese ions were trapped homogeneously on an atomic scale throughout the precursor. Such a structure eliminates the need for long-range diffusion during the formation of lithium manganese oxides. Therefore, spinel LiMn₂O₄ was synthesized at temperatures as low as 300°C. In this work, the electrochemical properties of Li/Li_xMn₂O₄ were studied. It is clear that the discharge curves exhibit two pseudo plateaus as the LiMn₂O₄ is fired to higher temperatures. The discharge capacity of LiMn₂O₄ increases from 84 to 117 mAh/g as the calcination temperature increases from 300 to 500°C. The LiMn₂O₄ powders calcined at low temperatures with a high specific surface area and an average valence of manganese exhibit a better cycle life.     

锰源对燃烧法制备5V级正极材料LiNi0.5Mn1.5O4的影响

以硝酸锰和醋酸锰,采用蔗糖燃烧法制备锂离子电池正极材料LiNi0.5Mn1.5O4通过XRD、SEM、粒径分布测试、循环伏安、恒流充放电测试以及交流阻抗等方法,研究了醋酸锰和硝酸锰对产物的结构、形貌、粒径及电化学性能的影响。XRD测试结果表明样品的结构都为立方尖晶石型,属于Fd3m空间群。不同的锰源对材料的粒径及粒径分布有很大的影响。以醋酸锰为原料制得的材料的粒径较小并且分布更均匀,有利于锂离子的脱出和嵌入从而提高电化学性能。以醋酸锰为锰源制得的LiNi0.5Mn1.5O4在3.6~5.2 V的充放电电压范围内的电化学性能更好,1C(1C=140.0 mA.g-1)倍率的首次放电容量为144.5 mAh.g-1,循环100周后容量保持率为96%,在3C,5C,10C以及20C的放电容量分别为136.3,132.0,124.7以及96.6 mAh.g-1。     

Ge4+、Sn4+掺杂尖晶石LiMn2O4的合成与电化学表征

使用Ge⁴⁺、Sn⁴⁺作为掺杂离子, 通过高温固相法制备四价阳离子掺杂改性的尖晶石LiMn₂O₄材料. X射线衍射(XRD)和扫描电子显微镜(SEM)分析表明, Ge⁴⁺离子取代尖晶石中Mn⁴⁺离子形成了LiMn_2-xGe_xO₄ (x=0.02,0.04, 0.06)固溶体; 而Sn⁴⁺离子则以SnO₂的形式存在于尖晶石LiMn₂O₄的颗粒表面. Ge⁴⁺离子掺入到尖晶石LiMn₂O₄材料中, 抑制了锂离子在尖晶石中的有序化排列, 提高了尖晶石LiMn₂O₄的结构稳定性; 而在尖晶石颗粒表面的SnO₂可以减少电解液中酸的含量, 抑制酸对LiMn₂O₄活性材料的侵蚀. 恒电流充放电测试表明, 两种离子改性后材料的容量保持率均有较大幅度的提升, 有利于促进尖晶石型LiMn₂O₄锂离子电池正极材料的商业化生产.     

球磨辅助高温固相法制备Li1.0Na0.2Ni0.13Co0.13Mn0.54O2正极材料及其性能

以乙酸盐(乙酸锂、乙酸钠、乙酸钴、乙酸镍、乙酸锰等)为原材料,采用球磨辅助高温固相法制备Li_1.0Na_0.2Ni_0.13Co_0.13Mn_0.54O₂正极材料。借助XRD、SEM等表征材料的结构和形貌,利用循环伏安、恒流充放电、交流阻抗等方法研究材料的电化学性能。结果表明,钠的掺杂导致颗粒表面光滑度降低,形成Na_0.77MnO_2.05新相。0.05C活化过程中,掺钠样品和未掺钠样品首次放电比容量分别为258.4 mAh·g^-1和215.8 mAh·g^-1,库伦效率分别为75.2%和72.8%;2C放电比容量分别为116.3 mAh·g^-1和106.2 mAh·g^-1。研究发现,掺钠可减小首次充放电过程的不可逆容量,提高容量保持率;改善倍率性能与容量恢复特性;降低SEI膜阻抗和电荷转移阻抗;掺钠后样品首次循环就可以基本完成Li₂MnO₃组分向稳定结构的转化,而未掺杂的样品需要两次循环才能逐步完成该过程;XPS结果表明,掺钠样品中Ni²⁺、Co³⁺、Mn⁴⁺所占比例明显提高,改善了样品的稳定性和电化学性能;循环200次后的XRD结果表明掺钠与未掺钠材料在脱嵌锂反应中的相变化过程基本一致,良好有序的层状结构遭到破坏是循环过程中容量衰减的主要原因。     

Synthesis and phase transition of Li-Mn-O spinels with high Li/Mn ratio by thermo-decomposition of LiMnC2O4(Ac)

LiMnC₂O₄(Ac) precursor in which Li⁺ and Mn²⁺ were amalgamated in one molecule was prepared by solid-state reaction at room-temperature using manganese acetate, lithium hydroxide and oxalic acid as raw materials. By thermo-decomposition of LiMnC₂O₄(Ac) at various temperatures, a series of Li_1+y[Mn_2−xLi_x]_16dO₄ spinels were prepared with Li₂MnO₃ as impurities. The structure and phase transition of these spinels were investigated by XRD, TG/DTA, average oxidation state of Mn and cyclic voltammeric techniques. Results revealed that the Li-Mn-O spinels with high Li/Mn ratio were unstable at high temperature, and the phase transition was associated with the transfer of Li⁺ from octahedral 16c sites to 16d sites. With the sintering temperature increasing from 450 to 850 °C, the phase structure varied from lithiated-spinel Li₂Mn₂O₄ to Li₄Mn₅O₁₂-like to LiMn₂O₄-like and finally to rock-salt LiMnO₂-like. A way of determining x with average oxidation state of Mn and the content of Li₂MnO₃ was also demonstrated.     

不同组分下富锂正极材料xLi_2MnO_3·(1-x)LiNi_(0.5)Mn_(0.5)O_2(x=0.1-0.8)的晶体结构与电化学性能

采用溶胶-凝胶法制备了一系列富锂锰基正极材料xLi2MnO3?(1-x)LiNi0.5Mn0.5O2(x=0.1-0.8),通过X射线衍射(XRD)仪,扫描电子显微镜(SEM)和电化学测试等检测手段表征了所得样品的晶体结构与电化学性能,研究了不同组分下富锂材料的结构与电化学性能.结果表明:Li2MnO3组分含量较高时,材料的首次放电容量较高,但循环稳定性较差;该组分含量较少时,所得样品中出现尖晶石杂相,且放电容量较低,但循环稳定性较好;综合来看,x=0.5时材料的电化学性能最优.x=0.4,0.6时材料也表现出了较好的电化学性能,值得关注.     

溶胶-凝胶法合成Li_(1-x)Na_xMn_2O_4及其作为水系锂离子电池正极材料的电化学性能

用溶胶凝胶法合成了Na+离子掺杂的Li_(1-x)Na_xMn_2O_4(x=0,0.01,0.03,0.05)。X射线衍射图表明Na+取代Li+进入Li_(1-x)Na_xMn_2O_4晶格中,扫描电镜图看出产物是粒径为100~300 nm的颗粒。恒流充放电测试结果表明,Li_(0.97)Na_(0.03)Mn_2O_4在2C倍率下循环100圈后放电容量保持率比未掺杂的LiMn_2O_4从51.2%提升到84.1%。循环伏安测试表明Na+离子掺杂降低了材料极化且增大了锂离子扩散系数。10C倍率下Li0.97Na0.03Mn2O4仍有79.0 m Ah·g-1的放电容量,高于未掺杂样品的52.1 m Ah·g~(-1)。Na+离子掺杂可以稳定材料结构并提高锂离子扩散系数,从而提高LiMn_2O_4的电化学性能,是一种可行的改性方法。     

溶胶-凝胶法合成Li1-xNaxMn2O4及其作为水系锂离子电池正极材料的电化学性能

用溶胶凝胶法合成了Na⁺离子掺杂的Li_1-xNa_xMn₂O₄(x=0,0.01,0.03,0.05)。X射线衍射图表明Na⁺取代Li⁺进入Li_1-xNa_x Mn₂O₄晶格中,扫描电镜图看出产物是粒径为100~300 nm的颗粒。恒流充放电测试结果表明,Li_0.97Na_0.03Mn₂O₄在2C倍率下循环100圈后放电容量保持率比未掺杂的LiMn₂O₄从51.2%提升到84.1%。循环伏安测试表明Na⁺离子掺杂降低了材料极化且增大了锂离子扩散系数。10C倍率下Li_0.97Na_0.03Mn₂O₄仍有79.0 mAh·g^-1的放电容量,高于未掺杂样品的52.1 mAh·g^-1。Na⁺离子掺杂可以稳定材料结构并提高锂离子扩散系数,从而提高LiMn₂O₄的电化学性能,是一种可行的改性方法。     

球磨辅助高温固相法制备Li1.0Na0.2Ni0.13Co0.13Mn0.54O2正极材料及其性能

以乙酸盐(乙酸锂、乙酸钠、乙酸钴、乙酸镍、乙酸锰等)为原材料,采用球磨辅助高温固相法制备Li_(1.0)Na_(0.2)Ni_(0.13)Co_(0.13)Mn_(0.54)O_2正极材料。借助XRD、SEM等表征材料的结构和形貌,利用循环伏安、恒流充放电、交流阻抗等方法研究材料的电化学性能。结果表明,钠的掺杂导致颗粒表面光滑度降低,形成Na_(0.77)Mn O_(2.05)新相。0.05C活化过程中,掺钠样品和未掺钠样品首次放电比容量分别为258.4 m Ah·g~(-1)和215.8 m Ah·g~(-1),库伦效率分别为75.2%和72.8%;2C放电比容量分别为116.3 m Ah·g~(-1)和106.2 m Ah·g~(-1)。研究发现,掺钠可减小首次充放电过程的不可逆容量,提高容量保持率;改善倍率性能与容量恢复特性;降低SEI膜阻抗和电荷转移阻抗;掺钠后样品首次循环就可以基本完成Li_2Mn O_3组分向稳定结构的转化,而未掺杂的样品需要两次循环才能逐步完成该过程;XPS结果表明,掺钠样品中Ni~(2+)、Co~(3+)、Mn~(4+)所占比例明显提高,改善了样品的稳定性和电化学性能;循环200次后的XRD结果表明掺钠与未掺钠材料在脱嵌锂反应中的相变化过程基本一致,良好有序的层状结构遭到破坏是循环过程中容量衰减的主要原因。     

(Li0.91Mn0.09)Mn2O4

Lithium manganese oxide crystals with composition (Li_0.91Mn_0.09)Mn₂O₄ were synthesized by a flux method. The crystals have a structure closely related to that of the cubic spinel LiMn₂O₄, but 9% of the lithium ions in the tetrahedral 4a site are substituted by Mn²⁺ ions. This substitution lowers the average Mn oxidation state below 3.5+, resulting in a Jahn–Teller distortion of the MnO₆ octahedron.     

LiMn2O4表面包覆Li4Ti5O12的制备及倍率特性

采用固相法合成了尖晶石型LiMn₂O₄，并通过溶胶-凝胶法制备了不同物质的量的百分比含量Li₄Ti₅O₁₂包覆的正极材料。X-射线衍射和扫描电镜结果表明，Li₄Ti₅O₁₂微粒包覆在LiMn₂O₄的表面没有产生晶体结构的变化。实验电池在室温下，以1C，2C和5C倍率作充放电循环测试；结果表明，与未包覆的LiMn₂O₄相比，表面包覆Li₄Ti₅O₁₂微粒的正极材料在高倍率下具有更好的循环稳定性。     

Electrochemical properties and synthesis of LiAl0.05Mn1.95O3.95F0.05 by a solution-based gel method for lithium secondary battery

The cathode materials, LiMn₂O₄, LiAl_0.05Mn_1.95O₄ and LiAl_0.05Mn_1.95O_3.95F_0.05 were firstly prepared by a simple solution-based gel method using the mixture of acetate and ethanol as the chelating agent. The synthesized samples were investigated by X-ray diffraction, scanning electronic microscope and differential and thermal analysis. The as-prepared powders were used as positive materials for lithium-ion battery, whose discharge capacity and cycle voltammogram properties were examined. The results revealed that LiAl_0.05Mn_1.95O_3.95F_0.05 synthesized by the solution-based gel method had higher initial capacity than LiAl_0.05Mn_1.95O₄ and better capacity retention rate (92%) than that of LiAl_0.05Mn_1.95O₄ and LiMn₂O₄, which revealed that Al and F dual-doped LiMn₂O₄ could gain better electrochemical properties of LiMn₂O₄ than only the Al-doped LiMn₂O₄.     

LiCoO2对LiMn2O4改性过程的研究

在LiCoO2、LiMn2O4、LiNiO2这三种锂离子电池正极材料中,尖晶石LiMn2O4由于具有价廉、对环境友好、使用安全的显著优点,被普遍认为是最有希望的新型正极材料。但该材料在高温下较快的容量衰减制约了其规模应用[1~3]。为改善LiMn2O4的高温性能,各国学者普遍采用掺杂法,即在制备L     

High capacity lithium-manganese-nickel-oxide composite cathodes with low irreversible capacity loss and good cycle life for lithium ion batteries

We report a method to eliminate the irreversible capacity of 0.4Li_2MnO_3·0.6LiNi_(0.5)Mn_(0.5)O_2(Li_(1.17)Ni_(0.25)Mn_(0.583)O_2) by decreasing lithium content to yield integrated layered-spinel structures.XRD patterns,High-resolution TEM image and electrochemical cycling of the materials in lithium cells revealed features consistent with the presence of spinel phase within the materials.When discharged to about 2.8 V,the spinel phase of LiM_2O_4(M=Ni,Mn) can transform to rock-salt phase of Li_2M_2O_4(M=Ni,Mn) during which the tetravalent manganese ions are reduced to an oxidation state of 3.0.So the spinel phase can act as a host to insert back the extracted lithium ions(from the layered matrix) that could not embed back into the layered lattice to eliminate the irreversible capacity loss and increase the discharge capacity.Their electrochemical properties at room temperature showed a high capacity(about 275 mAh g~(-1) at 0.1 C) and exhibited good cycling performance.     

石墨烯/尖晶石LiMn2O4纳米复合材料制备及电化学性能

采用溶胶凝胶法和还原氧化石墨法制备尖晶石LiMn2O4纳米晶和石墨烯纳米片,并采用冷冻干燥法制备了石墨烯/尖晶石LiMn2O4纳米复合材料,利用XRD、SEM、AFM等对其结构及表面形貌进行表征;利用CV、充放电、EIS研究纳米复合材料的电化学性能和电极过程动力学特征。结果表明:纳米LiMn2O4电极材料及其石墨烯掺杂纳米复合材料的放电比容量分别为107.16 mAh.g-1,124.30 mAh.g-1,循环100周后,对应容量保持率为74.31%和96.66%,石墨烯可显著改善尖晶石LiMn2O4电极材料的电化学性能,归结于其良好的导电性。纳米复合材料EIS上感抗的产生与半导体尖晶石LiMn2O4不均匀地分布在石墨烯膜表面所造成局域浓差有关,并提出了感抗产生的模型。     

锂离子电池镍掺杂尖晶石LiMn2O4正极材料的电子结构

采用密度泛甬平面波赝势方法对LiMn2O4和LiNi0.5Mn1.5O4的几何结构进行了优化,并计算了相应的电子结构.计算的结果表明:在Li 脱嵌前后,LiMn2O4和LiNi0.5Mn1.5O4均为导体,且锂元素主要以离子形式存在于两种材料中,O2p轨道与Mn(Ni)的3d轨道形成了较强的共价键.Li 嵌入导致Mn(Ni)3d轨道的态密度峰发生移动.Ni的掺杂导致Mn(Ni)和O2p轨道的成键作用得以加强,电子在Mn(Ni)3d轨道的填充发生变化,从而提高了电池的充放电电压.     

Lithium insertion into manganese dioxide polymorphs in aqueous electrolytes

The electrochemical behaviour of the spinel-like LiMn₂O₄ was studied in non-aqueous and aqueous saturated alkali nitrate electrolytes in comparison with the layered manganese dioxide δ-MnO₂. The results obtained by galvanostatic and cyclic voltammetry techniques showed that the insertion of Li⁺/e^– or H⁺/e^– depends on both the host lattice and the type of electrolyte. The spinel-like LiMn₂O₄ preferably allowed the insertion of Li⁺/e^– in non-aqueous and aqueous saturated LiNO₃ electrolytes, as observed from the similarity of the electrochemical behaviour in these electrolytes and the stability of the structure. This was explained by the presence of a three-dimensional network of vacant tetrahedral and half-filled octahedral sites in LiMn₂O₄, which guarantee high mobility of Li⁺ ions. The layered manganese dioxide could be inserted by Li⁺/e^– only in non-aqueous electrolytes. The work described herein was carried out at the Institut für Anorganische und Analytische Chemie, Technische Universit?t Berlin, Germany     

Analysis of the temperature dependence of the high-frequency EMR spectra of Mn ions in the lithium-ion battery material LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>

This paper deals with the analysis of the temperature dependence of high-frequency EMR (HF-EMR) spectra due to Mn³⁺ and Mn⁴⁺ ions in the lithium manganese spinel LiMn₂O₄. A range of powder samples obtained by the sol-gel method with calcinations in several temperature ranges were prepared for this study. Based on the initial characterization carried out by a number of techniques, the physicochemical and structural properties of the samples were earlier determined. Independently, temperature magnetization and HF-EMR measurements were carried out. The EMR spectra vary strongly between samples, indicating possible structural or chemical changes. Quantitative analysis of the temperature dependence of the HF-EMR spectra due to Mn³⁺ and Mn⁴⁺ ions in LiMn₂O₄ is presented in this paper. The spectral analysis concerns the line shape, linewidth, intensity and g-factors. Fittings using the Lorentzian spectral shape and, to a certain extent, the Gaussian spectral shape have been carried out in order to parameterize the temperature dependence of the HF-EMR spectra. This parameterization of the HF-EMR experimental data enables a deeper characterization of the samples. Subsequently, a better insight into the role of the Mn³⁺ and Mn⁴⁺ ions in accounting for the characteristics most suitable for application of LiMn₂O₄ as a cathode material may be gained.     

尖晶石LiMn2O4高温电化学容量衰减及改进

综述了高温下尖晶石LiMn2O4容量衰减的原因、机理研究和改进它的高温性能的方法以及目前的进展,且指出了可能的提高它的高温性能的途径。     

球形尖晶石LiMn2O4掺杂钇的性能研究

利用控制结晶方法, 在前驱体碳酸锰中共沉淀掺杂适量的钇, 得到球形掺杂钇的碳酸锰, 在540 ℃预烧后, 与锂盐一起焙烧, 可以得到高活性的掺钇球形尖晶石LiMn₂O₄. XRD分析表明, 产物中无杂相产生. 研究表明, 掺杂钇与掺杂其它金属离子的特性不一样, 钇具有催化特性, 掺杂钇可以提高尖晶石LiMn₂O₄中锰的活性. 掺钇使得更多的Mn^3＋参加电化学反应, 增加容量; 但同时也使更多的锰与电解液反应, 造成锰的溶解, 容量损失. 掺钇量越多, 锰的溶解量越大. 因此, 合适的掺杂量对于保证产品良好的电化学性能至关重要. 实验证明, 掺钇0.5%的产品Li(Y_0.005Mn_0.995)₂O₄具有较好的电化学性能. 其常温初始比容量为130 mAh•g^－1, 大于纯相的锰酸锂的125 mAh•g^－1, 100次循环后比容量为120 mAh•g^－1, 容量保持率为92.3%.