Effect of surface composition on electronic structure, stability, and electrocatalytic properties of Pt-transition metal alloys: Pt-skin versus Pt-skeleton surfaces

The surface properties of PtM (M = Co, Ni, Fe) polycrystalline alloys are studied by utilizing Auger electron spectroscopy, low energy ion scattering spectroscopy, and ultraviolet photoemission spectroscopy. For each alloy initial surface characterization was done in an ultrahigh vacuum (UHV) system, and depending on preparation procedure it was possible to form surfaces with two different compositions. Due to surface segregation thermodynamics, annealed alloy surfaces form the outermost Pt-skin surface layer, which consists only platinum atoms, while the sputtered surfaces have the bulk ratio of alloying components. The measured valence band density of state spectra clearly shows the differences in electronic structures between Pt-skin and sputtered surfaces. Well-defined surfaces were hereafter transferred out from UHV and exposed to the acidic (electro)chemical environment. The electrochemical and post-electrochemical UHV surface characterizations revealed that Pt-skin surfaces are stable during and after immersion to an electrolyte. In contrast all sputtered surfaces formed Pt-skeleton outermost layers due to dissolution of transition metal atoms. Therefore, these three different near-surface compositions (Pt-skin, Pt-skeleton, and pure polycrystalline Pt) all having pure-Pt outermost layers are found to have different electronic structures, which originates from different arrangements of subsurface atoms of the alloying component. Modification in Pt electronic properties alters adsorption/catalytic properties of the corresponding bimetallic alloy. The most active systems for the electrochemical oxygen reduction reaction are established to be the Pt-skin near-surface composition, which also have the most shifted metallic d-band center position versus Fermi level.     

Impact of metal cations on the electrocatalytic properties of Pt/C nanoparticles at multiple phase interfaces

Proton-exchange membrane fuel cells (PEMFCs) use carbon-supported nanoparticles based on platinum and its alloys to accelerate the rate of the sluggish oxygen-reduction reaction (ORR). The most common metals alloyed to Pt include Co, Ni and Cu, and are thermodynamically unstable in the PEMFC environment. Their dissolution yields the formation and redistribution of metal cations (M(y+)) within the membrane electrode assembly (MEA). Metal cations can also contaminate the MEA when metallic bipolar plates are used as current collectors. In each case, the electrical performance of the PEMFC severely decreases, an effect that is commonly attributed to the poisoning of the sulfonic acid groups of the perfluorosulfonated membrane (PEM) and the resulting decrease of the proton transport properties. However, the impact of metal cations on the kinetics of electrochemical reactions involving adsorption/desorption and bond-breaking processes remains poorly understood. In this paper, we use model electrodes to highlight the effect of metal cations on Pt/C nanoparticles coated or not with a perfluorosulfonated ionomer for the CO electrooxidation reaction and the oxygen reduction reaction. We show that metal cations negatively impact the ORR kinetics and the mass-transport resistance of molecular oxygen. However, the specific adsorption of sulfonate groups of the Nafion? ionomer locally modifies the double layer structure and increases the tolerance to metal cations, even in the presence of sulphate ions in the electrolyte. The survey is extended by using an ultramicroelectrode with cavity and a solid state cell (SSC) specifically developed for this study.     

Electronic structures of Pt-Co and Pt-Ru alloys for CO-tolerant anode catalysts in polymer electrolyte fuel cells studied by EC-XPS

CO tolerance at pure Pt, Pt-Co, and Pt-Ru alloys was investigated by X-ray photoelectron spectroscopy combined with an electrochemical cell (EC-XPS) in order to discover a hint for designing higher performance anode catalysts. After the electrochemical stabilization and/or CO adsorption, these electrodes were immediately transferred to the XPS chamber without exposure to air to avoid contamination of the surfaces. It was revealed that alloying with Co or Ru modified the electronic structures of Pt atoms, resulting in a positive core level (CL) shift of Pt 4f(7/2) which could weaken the Pt-CO interaction. For the Pt-Co alloy electrode, the Pt 4f(7/2) CL shift remained after the electrochemical stabilization despite Co dissolution and formation of a Pt skin layer. Changes in surface core level shifts (DeltaSCLSs) induced by CO adsorption were evaluated and related to the CO adsorption energy. The values of DeltaSCLS at these alloys were smaller than that of pure Pt, indicating that Ru and Co are effective elements to weaken the bond strength of Pt-CO.     

Shell-anchor-core structures for enhanced stability and catalytic oxygen reduction activity

Density functional theory is used to evaluate activity and stability properties of shell-anchor-core structures. The structures consist of a Pt surface monolayer and a composite core having an anchor bilayer where C atoms in the interstitial sites lock 3d metals in their locations, thus avoiding their surface segregation and posterior dissolution. The modified subsurface geometry induces less strain on the top surface, thus exerting a favorable effect on the surface catalytic activity where the adsorption strength of the oxygenated species becomes more moderate: weaker than on pure Pt(111) but stronger than on a Pt monolayer having a 3d metal subsurface. Here we analyze the effect of changing the nature of the 3d metal in the subsurface anchor bilayer, and we also test the use of a Pd monolayer instead of Pt on the surface. It is found that a subsurface constituted by two layers with an approximate composition of M(2)C (M = Fe, Ni, and Co) provides a barrier for the migration of subsurface core metal atoms to the surface. Consequently, an enhanced resistance against dissolution in parallel to improved oxygen reduction activity is expected, as given by the values of adsorption energies of reaction intermediates, delayed onset of water oxidation, and/or low coverage of oxygenated species at surface oxidation potentials.     

First-principles study of superabundant vacancy formation in metal hydrides

Recent experiments have established the generality of superabundant vacancies (SAV) formation in metal hydrides. Aiming to elucidate this intriguing phenomenon and to clarify previous interpretations, we employ density-functional theory to investigate atomic mechanisms of SAV formation in fcc hydrides of Ni, Cu, Rh, Pd, Ag, Ir, Pt, and Au. We have found that upon H insertion, vacancy formation energies reduce substantially. This is consistent with experimental suggestions. We demonstrate that the entropy effect, which has been proposed to explain SAV formation, is not the main cause. Instead, it is the drastic change of electronic structure induced by the H in the SAV hydrides, which is to a large extent responsible. Interesting trends in systems investigated are also found: ideal hydrides of 5d metals and noble metals are unstable compared to the corresponding pure metals, but the SAV hydrides are more stable than the corresponding ideal hydrides, whereas opposite results exist in the cases of Ni, Rh, and Pd. These trends of stabilities of the SAV hydrides are discussed in detail and a general understanding for SAV formation is provided. Finally, we propose an alternative reaction pathway to generate a SAV hydride from a metal alloy.     

Synthesis of carbon-supported sub-2 nanometer bimetallic catalysts by strong metal–sulfur interaction

Small-sized bimetallic nanoparticles that integrate the advantages of efficient exposure of the active metal surface and optimal geometric/electronic effects are of immense interest in the field of catalysis, yet there are few universal strategies for synthesizing such unique structures. Here, we report a novel method to synthesize sub-2 nm bimetallic nanoparticles (Pt–Co, Rh–Co, and Ir–Co) on mesoporous sulfur-doped carbon (S–C) supports. The approach is based on the strong chemical interaction between metals and sulfur atoms that are doped in the carbon matrix, which suppresses the metal aggregation at high temperature and thus ensures the formation of small-sized and well alloyed bimetallic nanoparticles. We also demonstrate the enhanced catalytic performance of the small-sized bimetallic Pt–Co nanoparticle catalysts for the selective hydrogenation of nitroarenes.

The strong interactions between metal and sulfur atoms doped in a carbon matrix allow for the synthesis of supported sub-2 nanometer M–Co (M = Pt, Rh, Ir) bimetallic nanocluster catalysts.     

General Synthesis of Single-Atom Catalysts for Hydrogen Evolution Reactions and Room-Temperature Na-S Batteries

Herein, we report a comprehensive strategy to synthesize a full range of single-atom metals on carbon matrix, including V, Mn, Fe, Co, Ni, Cu, Ge, Mo, Ru, Rh, Pd, Ag, In, Sn, W, Ir, Pt, Pb, and Bi. The extensive applications of various SACs are manifested via their ability to electro-catalyze typical hydrogen evolution reactions (HER) and conversion reactions in novel room-temperature sodium sulfur batteries (RT-Na-S). The enhanced performances for these electrochemical reactions arisen from the ability of different single active atoms on local structures to tune their electronic configuration. Significantly, the electrocatalytic behaviors of diverse SACs, assisted by density functional theory calculations, are systematically revealed by in situ synchrotron X-ray diffraction and in situ transmission electronic microscopy, providing a strategic library for the general synthesis and extensive applications of SACs in energy conversion and storage.     

Nanoporous ultra-high-entropy alloys containing fourteen elements for water splitting electrocatalysis

High-entropy alloys (HEAs) are near-equimolar alloys comprising five or more elements. In recent years, catalysis using HEAs has attracted considerable attention across various fields. Herein, we demonstrate the facile synthesis of nanoporous ultra-high-entropy alloys (np-UHEAs) with hierarchical porosity via dealloying. These np-UHEAs contain up to 14 elements, namely, Al, Ag, Au, Co, Cu, Fe, Ir, Mo, Ni, Pd, Pt, Rh, Ru, and Ti. Furthermore, they exhibit high catalytic activities and electrochemical stabilities in the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in acidic media, superior to that of commercial Pt/graphene and IrO₂ catalysts. Our results offer valuable insights for the selection of elements as catalysts for various applications.

Nanoporous ultra-high-entropy alloys containing 14 elements (Al, Ag, Au, Co, Cu, Fe, Ir, Mo, Ni, Pd, Pt, Rh, Ru, and Ti) were obtained by dealloying. The products showed excellent electrocatalytic performance for water splitting in acidic media.     

碳载合金 IrM（M = Fe，Ni，Co）纳米颗粒催化酸性与碱性介质中氢氧化反应

质子交换膜燃料电池(PEMFC)因能量转化率高、电流密度大、对负荷响应快及环境友好等优点而应用前景广阔.然而, Pt基催化剂的大量使用使得 PEMFC成本居高不下,阻碍了其商业化进程.金属 Ir具有良好的稳定性和相比 Pt较低的成本,可替代金属 Pt催化燃料电池阳极氢氧化反应.但是, Ir基催化剂的催化活性比 Pt低,难以满足商业化要求.通过合金调控 Ir纳米晶的电子结构和几何结构是降低 Ir用量、提高 Ir催化剂氢氧化活性的有效方法.
　　本文研究了 Ir基合金纳米晶中合金元素(Fe, Ni, Co)所产生的合金效应在酸碱性介质中对催化氢氧化的影响.采用溶剂蒸发-氢气还原法合成了具有相近合金度且平均粒径小于5 nm的 IrFe, IrNi和 IrCo纳米合金催化剂.电化学测试表明, IrNi合金催化剂具有最高的催化氢氧化活性.在酸性介质中, IrNi合金催化剂的质量比活性达到152 A/gIr (@0.1 V vs RHE),高于 IrFe (146 A/gIr)和IrCo (133 A/gIr)合金催化剂以及商业化 Pt/C催化剂(116 A/gPt).而在碱性介质中, Ir基合金催化剂活性较酸性介质中低,各合金催化剂优劣次序与酸性介质中一致.结构分析表明,合金化致使 Ir晶格收缩,收缩程度以 IrFe, IrNi和 IrCo的顺序依次降低. IrNi合金催化剂中 Ni合金元素诱导 Ir发生晶格收缩适中,使催化剂与中间物种(Had, OHad)的相互作用适度,从而获得最优的催化性质.另外,合金效应在不同 pH介质中影响不一：在酸性介质中,由合金元素(Fe, Ni, Co)导致的 Ir–Had相互作用弱化是提高氢氧化活性的主要原因;在碱性介质中,催化剂表面的亲氧效应决定了电极表面的 OHad吸/脱附性质和 Had表面覆盖度,从而影响催化氢氧化活性.     

Carbon/titanium oxide supported bimetallic platinum/iridium nanocomposites as bifunctional electrocatalysts for lithium-air batteries

Platinum (Pt) and iridium (Ir) catalysts are well known to strongly enhance the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) kinetics, respectively. Pt–Ir-based bimetallic compounds along with carbon-supported titanium oxides (C–TiO₂) have been synthesized for the application as electrocatalysts in lithium oxygen batteries. Transition metal oxide-based bimetallic nanocomposites (Pt–Ir/C–TiO₂) were prepared by an incipient wetness impregnation technique. The as-prepared electrocatalysts were composed of a well-dispersed homogenous alloy of nanoparticles as confirmed by X-ray diffraction patterns and Fourier transform scanning electron microscopy analyses. The electrochemical characterizations reveal that the Pt–Ir/C–TiO₂ electrocatalysts were bifunctional with high activity for both ORR and OER. When applied as an air cathode catalyst in lithium-air batteries, the electrocatalyst improved the battery performance in terms of capacity, reversibility, and cycle life compared to that of cathodes without any catalysts.     

Mixed-metal pt monolayer electrocatalysts for enhanced oxygen reduction kinetics

We have synthesized a new class of electrocatalysts for the O2 reduction reaction, consisting of a mixed monolayer of Pt and another late transition metal (Ir, Ru, Rh, Re, or Os) deposited on a Pd(111) single crystal or on carbon-supported Pd nanoparticles. Several of these mixed monolayer electrocatalysts exhibited very high activity and increased stability of Pt against oxidation, as well as a 20-fold increase in a Pt mass-specific activity, compared with state-of-the-art all-Pt electrocatalysts. Their superior activity and stability reflect a low OH coverage on Pt, caused by the lateral repulsion between the OH adsorbed on Pt and the OH or O adsorbed on neighboring, other than Pt, late transition metal atoms. The origin of this effect was identified through a combination of experimental and theoretical methods, employing electrochemical techniques, in situ X-ray absorption spectroscopy, and periodic, self-consistent density functional theory calculations. This new class of electrocatalysts promises to alleviate some major problems of existing fuel cell technology by simultaneously decreasing materials cost and enhancing performance. Our studies suggest a new way of synthesizing improved ORR catalysts through the modification and control of the surface reactivity of Pt-based mixed monolayers supported on transition metals other than Pt. In addition to improving the ORR catalysts, co-depositing oxophilic metals may be a promising possibility for improving a variety of other catalysts.     

Chemical Dealloying Mechanism of Bimetallic Pt–Co Nanoparticles and Enhancement of Catalytic Activity toward Oxygen Reduction

The chemical dealloying mechanism of bimetallic Pt–Co nanoparticles (NPs) and enhancement of their electrocatalytic activity towards the oxygen reduction reaction (ORR) have been investigated on a fundamental level by the combination of X‐ray absorption spectroscopy (XAS) and aberration‐corrected scanning transmission electron microscopy (STEM). Structural parameters, such as coordination numbers, alloy extent, and the unfilled d states of Pt atoms, are derived from the XAS spectra, together with the compositional variation analyzed by line‐scanning energy‐dispersive X‐ray spectroscopy (EDX) on an atomic scale, to gain new insights into the dealloying process of bimetallic Pt–Co NPs. The XAS results on acid‐treated Pt–Co/C NPs reveal that the Co–Co bonding in the bimetallic NPs dissolves first and the remaining morphology gradually transforms to a Pt‐skin structure. From cyclic voltammetry and mass activity measurements, Pt–Co alloy NPs with a Pt‐skin structure significantly enhance the catalytic performance towards the ORR. Further, it is observed that such an imperfect Pt‐skin surface feature will collapse due to the penetration of electrolyte into layers underneath and cause further dissolution of Co and the loss of Pt. The electrocatalytic activity decreases accordingly, if the dealloying process lasts for 4 h. The findings not only demonstrate the importance of appropriate treatment of bimetallic catalysts, but also can be referred to other Pt bimetallic alloys with transition metals.     

Temperature dependence of oxygen reduction activity at Pt-Fe, Pt-Co, and Pt-Ni alloy electrodes

Oxygen reduction reaction (ORR) activity and H(2)O(2) formation at Pt(54)Fe(46), Pt(68)Co(32), and Pt(63)Ni(37) electrodes in 0.1 M HClO(4) solution at 20 to 90 degrees C were investigated by using a channel flow double electrode method. In the temperature range of 20-50 degrees C, the apparent rate constants k(app) for ORR at these electrodes were found to be 2.4-4.0 times larger than that at a pure Pt electrode, whereas their apparent activation energies of 41 kJ mol(-1) at -0.525 V vs E degrees (0.760 V vs RHE at 30 degrees C) were comparable to that at the Pt electrode. H(2)O(2) yield was ca. 1.0% at Pt(54)Fe(46) and ca. 0.16% at Pt(68)Co(32) and Pt(63)Ni(37) between 0.3 and 1.0 V vs RHE. The k(app) values at the alloy electrodes decreased with elevating temperature above 60 degrees C, and settled to almost the same values at the Pt electrode. The H(2)O(2) production was not detected at the alloy electrodes once heated at the high temperature in the solution, probably due to the thickening of the Pt skin-layer by a considerable dissolution of nonprecious metal components (Fe, Co, Ni) from the alloys.     

Synthesis of PtRu nanoparticles from the hydrosilylation reaction and application as catalyst for direct methanol fuel cell

Nanosized Pt, PtRu, and Ru particles were prepared by a novel process, the hydrosilylation reaction. The hydrosilylation reaction is an effective method of preparation not only for Pt particles but also for other metal colloids, such as Ru. Vulcan XC-72 was selected as catalyst support for Pt, PtRu, and Ru colloids, and TEM investigations showed nanoscale particles and narrow size distribution for both supported and unsupported metals. All Pt and Pt-rich catalysts showed the X-ray diffraction pattern of a face-centered cubic (fcc) crystal structure, whereas the Ru and Ru-rich alloys were more typical of a hexagonal close-packed (hcp) structure. As evidenced by XPS, most Pt and Ru atoms in the nanoparticles were zerovalent, except a trace of oxidation-state metals. The electrooxidation of liquid methanol on these catalysts was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results concluded that some alloy catalysts showed higher catalytic activities and better CO tolerance than the Pt-only catalyst; Pt56Ru44/C have displayed the best electrocatalytic performance among all carbon-supported catalysts.     

Preparation, characterization, and catalysis of mecro-catalysts

Because catalysis by metals is a surface phenomenon, many technological catalysts contain small (typically nanometre-sired) supported metal particles with a large fraction of the atoms exposed. Many reactions, such as hydrocarbon hydrogenations, are structure-insensitive, proceeding at approximately the same rates on metal particles of various sizes provided that they are larger than 1 nm and show bulk-like metallic behavior. But the catalytic properties are not known when metal particles become so small that their sizes are indium clusters consisting of several indium atoms. Here the catalytic behavior of precisely defined clusters of just four and six indium atoms on solid supports is shown. It is found that the Ir4 and Ir6 clusters differ in catalytic activity both from each other and from metallic Ir particles.     

在氢气氧化反应中具有高催化活性的Pt修饰的Ni/C纳米催化剂

随着能源需求的进一步增多和化石能源的大幅度减少,新型环境友好型能源成为近十年许多科研工作者的着力点.其中,燃料电池作为一种高效率、高能量密度、环境友好型能源引起了人们的关注.氢氧燃料电池研究最早、应用最早,具有得天独厚的优势.此外,由于近些年CO2的大量排放,造成了严重的温室效应,其处理也是一个严峻的课题.谢和平课题组提出的CO2矿化发电,不仅可以处理CO2,也可以作为新型能源应用,前景广阔.而不论是氢氧燃料电池还是CO2矿化电池,其阳极反应均为氢气氧化反应(HOR).Pt作为目前仍无法取代的HOR反应催化剂,不仅全球储量有限且价格昂贵,所以,寻找一种价格低廉催化性能好的催化剂成为这些新能源进一步应用的重要课题之一.对此人们进行了大量探索,主要包括尝试不同的载体、改变金属颗粒尺寸形貌等.其中,伽伐尼置换法对于制备纳米核壳结构催化剂以及降低金属颗粒尺寸、增加比表面积均有很大帮助.基于此,本文采用浸渍法和伽伐尼置换法制备了用Pt修饰Ni/C的纳米催化剂,使得纳米级活性金属均匀分散在载体上,加之双金属效应,相对于纯Pt/C催化剂,催化能力提高.浸渍法制得Ni/C前驱体,再将其置于纯乙醇中,用H2PtCl6作为Pt源置换部分Ni,得到Pt修饰的Ni/C催化剂.XRD射线衍射测试结果表明,一般的PtNi合金由于晶格相互影响,只会出现Pt的偏移衍射峰,而该催化剂均出现明显的PtNi两种元素的衍射峰,PtNi晶格互相没有影响.循环伏安法测试结果表明,在Pt-Ni/C系列催化剂中,Pt和Ni含量不同,其电化学活性面积(ECSA)各不相同.在金属总含量一致的前提下,随着Pt含量的增加,催化剂ECSA先增加后减小,最大值为66.90 m2/g,是市售Pt/C(54.12 m2/g)的1.24倍.Tafel测试HOR/HER反应交换电流密度的结果与ECSA结果一致,而Pt-Ni/C催化剂的交换电流密度最高可达485.45 A/g,是市售Pt/C(301.91 A/g)的1.6倍.对性能较好的Pt-Ni/C催化剂进行了表征,X射线光电子能谱结果发现,该催化剂载体上只有少部分Ni的氧化物裸露在表面,大部分为Pt.而透射电镜结果表明,该催化剂纳米级活性金属颗粒尺寸一致,且均匀地分散在载体表面.综合催化剂表征和电化学性能测试结果可知,使用伽伐尼置换法得到的Pt修饰的Ni/C催化剂分散均匀、颗粒尺寸小,且由于Pt作为主要催化活性金属分散于催化剂表面,而Ni作为辅助金属并不直接参与HOR反应,使得该催化剂具有较高的电化学活性.在Pt含量较少时,由于有很多Ni在催化剂表面,且催化层厚度较大,故催化活性一般.随着Pt含量的增加和Ni含量的减少,当催化剂表面只有很少Ni及相关化合物时,由于Pt比表面积大,故活性最高.当Pt含量继续增加时,Pt在Ni表面厚度增加,很多Pt被包裹,故催化活性再次降低.     

Theoretical Investigations of the Activation of CO_2 on the Transition Metal-doped Cu(100) and Cu(111) Surfaces

Periodic density functional theory calculations have been performed to investigate the chemisorption behavior of CO_2 molecule on a series of surface alloys that are built by dispersing individual middle-late transition metal(TM) atoms(TM = Fe, Co, Ni, Ru, Rh, Pd, Ag, Os, Ir, Pt, Au) on the Cu(100) and Cu(111) surfaces. The most stable configurations of CO_2 chemisorbed on different TM/Cu surfaces are determined, and the results show that among the late transition metals, Co, Ru, and Os are potentially good dopants to enhance the chemisorption and activation of CO_2 on copper surfaces. To obtain a deep understanding of the adsorption property, the bonding characteristics of the adsorption bonds are carefully examined by the crystal orbital Hamilton population technique, which reveals that the TM atom primarily provides d orbitals with z-component, namely d_z~2, d_(xz), and d_(yz) orbitals to interact with the adsorbate.     

Growth of single-layer carbon tubes assisted with iron-group metal catalysts in carbon arc

Single-layer (SL) carbon tubes were produced by arc evaporation of graphite rods containing iron-group metals (Fe, Co, Ni, Fe/Co, Co/Ni, Fe/Ni) under He and Ar gas. Transmission electron microscopy (TEM) revealed that these elemental and binary metals, excluding Fe which need a special atmosphere (a mixture of Ar and CH₄), showed catalytic activity producing SL tubes under pure inactive gases. Fe/Ni alloy was the most effectual catalysts for producing SL tubes. The highest abundance of SL tubes in raw soot was estimated to be ～ 10% from TEM observation. Smoke particles directly caught on TEM grids near an evaporation source during arcburning were also investigated, and it was suggested that small metal particles were first formed in the gas phase and then SL tubes grew from them.     

Electronic composition-property relationship applied to SO2 chemisorption on Pt111 surfaces, alloys, and overlayers

We have developed a new electronic composition-property relationship between the adsorption energy of molecules binding unequally to multiple atoms on metal surfaces and the electronic properties of the surface. This relationship allows the estimation of the relative stability of adsorbates on various surfaces, assuming that the adsorbate adopts the same local configuration on each surface, and therefore also allows the estimation of the adsorption energy of molecules through large regions of parameter space in alloy systems with data from only a few explicit calculations. We have applied this relationship to the adsorption of SO(2) on Pt surfaces alloyed with Pd, Cu, Ru, and Ni. Using a new formula for weighting the metal d-band, we found a strong linear relationship between the weighted positions of the d states of surfaces and the most stable molecular adsorption energies. The consequences of our electronic composition-property relationship for catalyst design are also discussed.     

铂族金属催化剂低温 CO氧化研究近期进展

CO氧化可能是多相催化领域最常见的反应,它不仅能作为探针反应研究催化剂结构、反应活性位等,而且在诸多实际过程如空气净化、汽车尾气污染物控制、燃料电池所用氢源净化等扮演重要角色.最早的 CO氧化催化剂为霍加拉特剂,其组分主要为 CuO与 MnO2混合氧化物,然而在实际应用过程中存在低温活性低、吸湿易失活等缺点.1987年, Haruta等发现湿化学法制备的氧化物负载 Au催化剂表现出非常高的低温 CO氧化活性及耐水稳定性,其 Au粒子以纳米尺度分散,进而引发了催化研究领域的“淘金热”及纳米催化研究热潮.而 CO氧化通常作为考察 Au催化剂结构性质的探针反应,也成为考核其它金属催化剂是否具有高活性的判据之一. Pt族金属上 CO氧化反应从 Langmuir等研究开始至今已有100多年,然而低温下该金属催化剂活性与 Au催化剂相比要低一个数量级.本质原因为 Pt族金属上 CO吸附较强, O2吸附与活化受到抑制,而该步骤被认为是 CO氧化的速控步,因而表现出较低的催化活性.通常 Pt族金属催化剂需要100oC以上 CO才能脱附, O2进而得以吸附.目前研究人员采取多种策略,其基本原则为削弱 Pt族金属上 CO吸附强度或者提供其它活性位供 O2吸附与活化.本综述将概括近十年来Pt族金属催化剂 CO氧化研究进展,主要总结室温甚至超低温条件下的研究成果.高活性 CO氧化催化剂主要是通过采用可还原氧化物为载体或助剂,或者改变催化剂表面性质如使表面富 OH基物种来形成. Au催化剂的研究发现,改变金属粒子尺寸极有可能获得不同寻常的催化性能,而常规的 Pt族金属催化剂研究主要是在纳米尺度.近期人们发现逐渐减小 Pt族金属粒子尺寸,从纳米到亚纳米甚至单原子时,其电荷状态逐渐呈正价形式,这有利于削弱其 CO吸附强度.此外,可通过增强金属载体间的相互作用,改变金属载体接触方式,如从核壳到交叉结联结构,构筑出更多的金属载体界面,使得 O2更容易吸附与活化或稳定更多的 OH基物种进而在此界面与吸附的 CO反应.伴随着表征技术的发展, CO氧化机理的认识也更加深入,这给催化剂的设计带来更多新的思路.(1)改变 CO吸附活化位,将 CO吸附活化位从金属转移到载体上,从而大大降低 CO吸附强度,活化的 CO物种在反应过程中容易溢流到金属载体界面处,这甚至有利于超低温度下(–100oC左右) CO氧化.(2)改变 O2活化形式. O2通常在 Pt族金属上容易以解离氧原子形式存在,通过改变载体、金属载体界面性质使得 O2以分子氧形式活化,如形成超氧或过氧物种,这有利于降低 CO氧化的活化能垒,进而提高其低温甚至超低温下 CO氧化活性.今后,设计并合成出在超低温度下能够氧化 CO的 Pt族金属催化剂将成为 CO氧化催化剂研究的重要方向之一.