凝胶自燃法合成LaxSr1-x CoyFe1-y O3-α纳米粉体

用凝胶自燃法制备了La_xSr_1-x Co_yFe_1-y O_3-α纳米粉体，研究了粉体的元素组成和掺杂性能，表征了粉体的晶相结构，测试了其粒度和形貌。结果表明应用凝胶自燃工艺合成的La_xSr_1-x Co_yFe_1-y O_3-α粉体材料粒子大小非常均匀，元素掺杂性能好，晶相单一，不需经高温热处理便能直接形成钙钛矿型结构。     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

钙钛矿型LaxSr1－xNi1－yCoyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧合成法, 制备La_xSr_1－xNi_1－yCo_yO₃复合氧化物的陶瓷粉末, 对钙钛矿氧化物进行了XRD结构分析. 在通氧或不通氧下测试氧还原和氧析出的循环伏安曲线. 结果表明: 该氧电极具有双功能催化特性, 但不完全可逆. 利用汞灯作为激发光源, 进行几种水溶性染料和五种混合染料光解实验, 利用紫外-可见、红外以及人工神经网络光度法研究La_xSr_1－xNi_1－yCo_yO₃的催化性能. 结果表明: La_xSr_1－xNi_1－yCo_yO₃ (x＝0.7, 0.9, 1; y＝0.3, 0.75)复合氧化物都具有较强光催化特性; La_xSr_1－xNi_1－yCo_yO₃的光催化活性高于La_xSr_1－xNiO₃, 这与B位离子(Ni^2—, Co^2－)的电子构型有关; Co^2＋的加入可使La_xSr_1－xNiO₃的光催化活性有所提高.     

新型中温固体氧化物燃料电池阴极材料Fe掺杂Sm0.5Sr0.5CoO3性能研究

本文系统研究了新型中温固体氧化物燃料电池(IT-SOFC)阴极材料Sm_0.5Sr_0.5Co_1-xFe_xO_3－δ(SSCF)的晶体结构、热膨胀系数、导电率及电化学性能。固相合成的Sm_0.5Sr_0.5Co_1-xFe_xO_3－δ化合物均为单相材料，随着掺Fe量的不同，SSCF的晶体结构发生变化，在0≤x≤0.4时，SSCF为正交晶系钙钛矿结构，在0.5≤x≤0.9时，SSCF为立方晶系钙钛矿结构。Fe掺杂可以显著的改善Sm_0.5Sr_0.5CoO₃的热膨胀系数，随着Fe含量的增加，热膨胀系数减小。在800℃下，SSCF导电率均大于100 S·cm^-1。随着Fe含量的增加，极化电阻增大；含量x=0.4时，极化电阻达到最大值；之后，随Fe含量的增加，极化电阻减小，在700～800 ℃时，Sm_0.5Sr_0.5Co_0.2Fe_0.8O_3－δ表现出了良好的氧催化活性。     

Bi4-xEuxTi3-yMyO12（M=Fe，Co，Ni）纳米颗粒的制备及光学和磁学性能

三层结构的Aurivillius相的Bi_4-xEu_xTi_3-yM_yO₁₂（x=0~0.6;M=Fe/Co/Ni,y=0.01,0.02,0.04,0.06,0.08,0.10）纳米颗粒,是通过共沉淀法和后续的高温煅烧处理所制备的。利用XRD,SEM,PL,Raman,PPMS等方法对样品进行表征,研究了不同掺杂浓度下的产物的物相、形貌和性能等。实验结果表明,通过掺杂,发现纳米颗粒的粒径变小,形貌更均一,分散性也更好。通过对掺杂离子浓度的优化,发现Eu³⁺离子的掺杂浓度为x=0.4时,发光强度是最强的。此外,对Ti位进行了磁性离子（Fe³⁺,Co³⁺和Ni²⁺）的掺杂,实验结果发现随着掺杂的磁性离子浓度的减少,发光强度是逐渐增强,而且产物具有很好的铁磁性。     

不同方法制备的CoxZr1-xO2催化剂及其氧化甲苯和甲醛的性能

采用沉淀法、水热法、热分解法和浸渍法制备了Co_xZr_1-xO₂催化剂。通过热重（TG）、X射线衍射（XRD）、扫描电子显微镜（SEM）、能量散射X射线光谱（EDS）、N₂吸附/脱附测试等手段对催化剂的理化性质进行了表征。结果表明,水热法制备的催化剂Co_xZr_1-xO₂-H（1∶1）中的钴、锆的分散性好、颗粒均匀、孔结构发达,比表面积可达到102 m²·g^-1,氧化甲苯和甲醛的活性优于其他催化剂,其表观活化能为65.2和53.6 kJ·mol^-1。Co_xZr_1-xO₂-H（1∶1）的优异催化性能与物种的分散度及协同效应、比表面积和孔结构有关。控制Co-Zr催化剂的制备方法可以获得良好的物化性能。     

表面缺陷α-Fe2O3(001)纳米片双活性位点类芬顿催化剂用于降解污染物

纯Fe₂O₃表面活性位点较少具有较低的催化活性限制了其在多相芬顿催化体系中的应用。通常采用元素掺杂、贵金属负载以及与其它化合物质复合等改性措施来提升催化活性,然而这些措施存在催化剂制备复杂,制备成本高以及催化剂的精细结构难以精准控制等问题。因此,本文提出在α-Fe₂O₃表面引入氧空位缺陷构筑双活性位点（Fe²⁺和氧空位）用于促进H₂O₂分解提高降解污染物降解效率。实验结果发现α-Fe₂O_3-x-330/H₂O₂体系具有较宽的pH使用范围（pH=2~10）。当pH=4时,罗丹明B的降解速率常数为0.834 h^-1,而且催化剂具有磁性,易回收重复使用。催化机理研究表明氧空位缺陷α-Fe₂O_3-x催化剂的氧空位和Fe²⁺两种活性位点均可促进H₂O₂分解,而且氧空位的引入有利于污染物在催化剂表面的吸附进一步提高催化性能。     

铕掺杂对Co3O4活化过一硫酸盐降解亚甲基蓝性能的增强

以Co （NO₃）₂和Eu （NO₃）₃为原料,采用草酸盐-热分解法制得了系列不同Co/Eu比例（n_Co/n_Eu）的多孔双金属复合氧化物催化剂,并对其活化过一硫酸盐（PMS）降解亚甲基蓝（MB）的性能进行对比评价。结果表明,按n_Co/n_Eu=9制得的材料（Co₉Eu₁）具有最为优异的活化PMS降解MB的性能。在温度为25℃、催化剂用量和PMS浓度分别为0.10 g·L^-1和0.6 mmol·L^-1的反应条件下,Co₉Eu₁/PMS体系对MB的降解率可达86.66%,而纯Co₃O₄催化下的MB降解率仅为52.62%。Co₉Eu₁出色的催化性能是由于Eu³⁺的缺电子特性增强了对吸附于催化剂表面PMS的极化而使其更易被主催化成分Co₃O₄活化。体系中阴离子C₂O₄^2-和HCO₃^-的存在对Co₉Eu₁/PMS氧化降解MB的性能具有明显抑制作用。猝灭实验和电子顺磁共振谱（EPR）证实Co₉Eu₁/PMS体系中同时存在SO₄^-·、·OH和·O₂^-三种自由基型活性物种以及¹O₂非自由基型活性物种,其中SO₄^-·对MB的氧化降解起关键作用。Co₉Eu₁具有良好的稳定性,在连续4次循环使用中其催化性能未见明显变化。     

Ba0.4Sr0.6Co1-xFexO3-δ系阴极材料的制备和表征

采用甘氨酸-硝酸盐(GNP)法合成了中温固体氧化物燃料电池阴极材料Ba_0.4Sr_0.6Co_1-xFe_xO_3-δ(x=0.0～0.8)系列粉体。利用XRD和SEM对材料的结构和微观形貌进行分析,用直流四端子法测量了烧结陶瓷体在中温(450～800 ℃)范围内的电导率。结果表明,制备的样品为单一钙钛矿相,随着Fe含量增加,XRD衍射峰值向高角度方向稍有偏移。电导率随着温度及Fe含量的变化出现极大值,在x＜0.2时,Ba_0.4Sr_0.6Co_1-xFe_xO_3-δ系列烧结体在中温(450～800 ℃)区的电导率,随Fe掺入量的增大而增大,x=0.2样品的电导率最高,800 ℃时达244.7 S·cm^-1,远超过文献报道值,进一步增大Fe含量导电性能变差。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.