可交联聚甲基丙烯酸甲酯的合成、表征及在阵列式波导光栅中的应用

合成了含环氧基团的可交联的甲基丙烯酸甲酯和甲基丙烯酸环氧丙酯的共聚物[Poly(MMA-co-GMA)],通过FTIR,NMR,GPC,DSC和AFM等技术对其进行了表征. 结果表明,所合成的聚合物材料具有较好的成膜性; 通过热固化使引入的环氧基团开环交联,该聚合物的玻璃化转变温度(Tg)比固化前提高了24 K,同时有效地降低了聚合物的双折射率. 用Poly(MMA-co-GMA)作为包层材料,双酚A型环氧化合物作为高折射率材料, 将其引入到包层材料中形成芯层材料的折射率在波长1.55 μm处可调,其范围是1.483~1.588. 采用旋涂、 铝掩膜和氧反应离子刻蚀的方法(RIE)制得了阵列式光波导. 测试结果表明,制作的波导在1.55 μm处实现了光的单模传输,光损小于3.0 dB/cm.      

二阶非线性光学活性聚酰亚胺有机-无机杂化材料的合成与表征

通过溶胶-凝胶法制备了含二阶非线性光学发色团分散红19(DR₁₉)的硅氧烷染料与聚酰亚胺有机-无机杂化材料.利用红外光谱、紫外-可见光谱、SEM、DSC和TGA等手段对其进行了表征.杂化极化后的序参数高达0.48,并具有优良的极化取向稳定性,423K下处理300h后,序参数仍能保持初始值的90%.杂化薄膜有较好的表面平整性,其断面呈网络结构.杂化材料的玻璃化转变温度(T_g)为561K,比纯聚酰亚胺的T_g(543K)高18K,表现出优良的高温热稳定性,其5%热失重温度为691K,10%热失重温度为758K.     

PMMA型非线性光学膜的制备及其极化取向

采用封管反应, 以较高产率(80%以上)合成了一种PMMA型的极化非线性光学聚合物材料. 该材料具有很好的成膜性, 用电晕极化的方法使其旋涂膜中的生色团极化取向, 并利用偏振红外光谱和偏振紫外光谱等方法, 对膜中生色团极化前后的取向进行了研究.     

异氰酸酯交联的环氧树脂基二阶非线性光学聚合物

通过双酚A 二 (缩水甘油醚 )与苯胺的逐步聚合反应合成环氧树脂类先驱聚合物BPAN ,进一步通过先驱聚合物的后重氮偶合反应 ,制备了侧链带偶氮生色团的二阶非线性光学聚合物BPAN 1A NT .将BPAN 1A NT与适当量的异氰酸酯交联剂M2 0S混合 ,得到了双组分非线性光学聚合物体系BPAN 1A NT M2 0S .该体系在电场极化的同时可发生交联固化 ,极化后其二阶非线性光学系数高达 10 5 2pm v(λ =1 0 6 4 μm) ,同时还具有很好的极化偶极取向稳定性 ,2 0 0℃时的非线性光学系数仍可维持在初始的 80 %以上 .上述双组分非线性光学聚合物材料 (BPAN 1A NT M2 0S)同时具有高二阶非线性光学系数和高极化偶极取向稳定温度 ,可以预期 ,在聚合物电光调制器、光开关等器件中将有很好的应用前景 .     

聚苯乙烯胶乳颗粒的成膜过程及尺寸效应

聚合物乳液成膜过程可分为介质蒸发、颗粒形变和相邻颗粒间高分子的扩散融合三个阶段.一般认为,环境温度达到或高于高分子的玻璃化转变温度(T_g)时颗粒才可能发生形变.Goudy等研究了粒径为0.24～1.05μm的聚苯乙烯(PS)胶乳的成膜过程,发现PS颗粒在368K(T_g约373K)热处理很长时间也不发生形变,而在378K热处理后,粒径较小的颗粒融合速度快于较大颗粒.     

丁腈羟型聚氨酯弹性体的分子结构设计与电机械性能研究

本文对端羟基聚丁二烯丙烯腈液态橡胶(丁腈羟，HTBN)进行端基化改性，合成带不同光活性端官能团的遥爪型丁腈羟(HTBN)预聚物，并最终通过光固化制备了不同分子链结构的丁腈羟型聚氨酯(BNPU)介电弹性体。研究表明，随着前驱体HTBN分子链长度的增加，固化交联后BNPU弹性体的线性链缠结网络密度增加，使得弹性体的模量(Y)和断裂伸长率(E_B)分别最高增加到1.89 MPa与112.26%,同时使弹性体的玻璃化转变温度(T_g)降低。根据活性封端基团的不同，采用季戊四醇三丙烯酸酯(PETA)封端的HTBN预聚物，光固化后的BNPU弹性体内部形成较大体积位阻的局部交联区域，可使BNPU弹性体的T_g升高，热分解速率降低，同时相分离导致的界面极化增强，从而进一步提升弹性体介电性能：使BNPU弹性体样品在10³ Hz频率下介电常数(ε′)最高达到807,介电损耗保持在1以下。最终局部大位阻交联结构和一定量的氰基结构可协同赋予BNPU弹性体优异的综合电机械性能，克服了纯聚氨酯和高交联度丁腈橡胶模量大、易击穿的问题。     

一种光交联电光聚合物的合成及其外部电光测量

合成了一种新的带有光交联基团的电光聚合物,其高分子基体是双酚A环氧树脂,二阶非线性生色团对硝基苯胺和光交联基团肉桂酰氯都键接在高分子链上.将聚合物溶解后旋涂成膜,对薄膜进行电晕极化.极化的后阶段用紫外光照射,使聚合物体系交联成网络结构,形成生色团取向长时间稳定的聚合物电光薄膜.用这种聚合物电光薄膜构成外部电光调制系统,测量了共面波导上的电信号.     

一种新型的交联极化聚合物的合成及性能研究

以成膜性能优异、主链上含有多个羟基的聚双酚A二缩水甘油醚-苯胺(BPAN)为骨架,将二阶非线性光学活性发色团分子以键合形式挂接到聚合物主链上,形成新型侧链型聚合物.此聚合物保留了原聚合物体系成膜性好和可进一步交联等优点.极化过程中以含有异氰酸酯基的同种发色团分子作为交联剂,得到发色团含量进一步提高的交联型极化聚合物.采用衰减全反射法(ATR)测得体系的电光系数(r₃₃)为6.7 pm/V(1315 nm).     

新型光交联互穿网络体系的合成与非线性光学性能

设计合成了侧链上接有肉桂酸酯基团功能化聚合物(E51-DO3-C)和侧链同时含有环氧基团和偶氮苯生色团的功能化低聚物(PPGF-DO3-50),这两种功能化聚合物可分别以环加成反应和阳离子光引发机制进行交联反应形成先交联IPN体系,研究了E51-DO3-C、PPGFDO3-50体系和光IPN体系的极化交联后材料的二阶非线性光学(NLO)性能。研究含DO3生色团的酚醛环氧甘油醚低聚体在BDS·2PF_6阳离子光引发下的光交联过程以及NLO性能,非线性光学系数d_(33)值稳定性较差。利用这两种体系的相容性,设计获得了复合物E51-DO3-C/PPGF-DO3-50,其d_(33)值稳定性有显著提高,室温下30天后d_(33)值保持初值的80％左右。     

一步法合成高T_g可溶含偶氮三嗪发色团的新型侧链含氟聚酰亚胺

采用一步法合成了一系列侧链含偶氮三嗪发色团的新型含氟聚酰亚胺FPI(x),并研究其溶解性能、热性能以及光学性能.该系列聚酰亚胺具有优良的溶解性能,不仅溶于NMP,DMAc,DMF,DMSO等强极性非质子性溶剂,而且还溶于THF和乙二醇单甲醚等低沸点溶剂.FPI(x)系列共聚聚酰亚胺具有较高的玻璃化转变温度(T_g,在544～562K之间),且与主链中染料发色团的含量无关.所有聚酰亚胺都表现出优良的高温稳定性,其5%热失重温度(T₅)比T_g高出100K以上,基本能满足电场极化对聚合物材料热稳定性的要求.另外,FPI(x)系列聚酰亚胺的紫外截止吸收波长小于500nm,即在大于500nm波长范围内基本透明.其面内折光指数n_TE随着染料发色团含量的增加而逐渐增加.     

高热稳定性和可逆交联性质的含新型偶氮发色团电光聚合物的研究(英文)

制备了两种新型的分别含有以三苯胺为电子给体的偶氮类发色团作为特征活性官能团和3-呋喃甲酸及受保护的马来酰亚胺的可交联型聚合物体系.通过研究表明利用该制备方法,发色团在聚合物中的含量得到了极大的提高,分别达到32 .1 %( NLO1-P1)和44 .4 %( NLO1-P2) .该聚合物体系以"Diels-Alder"[4 +2]环加成反应作为其交联特征,具有高温非交联、低温交联的特点,其过程与以往的热交联型聚合物相反,可解决传统电光交联聚合物中存在的热交联对极化效率影响的问题并用热失重分析法(TGA)和差示扫描量热法(DSC)分析了这一过程.此外DA交联型聚合物,不需要引入额外的助交联剂,克服了传统热交联聚合物分离难的问题,最大程度的保证了材料的纯度.     

Anionically prepared poly(ε-caprolactam-co-ε-caprolactone) and poly(ε-caprolactam-co-δ-valerolactone) copolymers: Thermal and mechanical properties

Thermal and representative physico-mechanical properties of newly prepared poly[(ε-caprolactam)-co-(ε-caprolactone)] and poly[(ε-caprolactam)-co-(δ-valerolactone)] copolymers were studied. The copolymers were synthesized by anionic polymerization of ε-caprolactam activated by isocyanate end-capped oligomeric aliphatic polyesters designated as the macroactivators (MAs). Type, concentration and molecular weight of the MAs were varied, which resulted in copolymers with different structure and properties. The impact of the new MAs used in this study on the glass transition temperature and the melting temperature of poly-ε-caprolactam was investigated by DSC. DMTA was used to analyze the effect of copolymerization on the storage modulus (E^′) and tan δ of poly-ε-caprolactam. Conventional and high-resolution TGA data revealed that all the synthesized polyesteramides possess good thermal stability. Mechanical properties were studied by notched impact and tensile testing. According to the experimental data the impact toughness increase with the MA content, being six time higher compared to the poly(ε-caprolactam) in the best situation. Water absorption was also considered in relation to the composition of the copolymers.     

Biosynthesis and biodegradability of copolythioesters from 3,3'-thiodipropionic acid and plant oils by Cupriviadus necator

To prepare sulfur-containing natural polymers effectively, several plant oils and 3,3'-thiodipropionic acid (TDP) have been used as carbon sources for the biosynthesis of copolymer poly[(3-hydroxybutyrate)-co-(3-mercaptopropionate)] [poly(3HB-co-3MP)] by a wild-type bacterium Cupriviadus necator H16. By using the plant oils, copolymer accumulation and incorporation of 3MP units are greater than those of cases using sugars. The 3MP fraction is controllable over a range of 1-39 mol-% by adjusting the cultivation conditions. Microbial degradability of the copolymers has been examined in an activated sludge supernatant. The biodegradation proceeded by two mechanisms: surface erosion and auto-catalytic hydrolysis, depending on the 3MP unit fraction, and show preferential degradation of 3HB unit sequences.     

Highly stable rigid main‐chain nonlinear optical polymers with nematic phase: Effect of liquid‐crystalline phase on nonlinear optical response

Nonlinear optical (NLO) rigid main‐chain polyesters containing azobenzene mesogens with high thermal and temporal stabilities were synthesized from derivatives of hydroxyphenylazobenzoic acid. The NLO properties of the homopolymer, poly[4‐(4‐hydroxy‐3‐methyl phenyl)azo]benzoic acid, and copolymers of 4‐[(4‐hydroxy‐3‐methylphenyl)azo]benzoic acid, 4‐[(4‐hydroxy‐2‐methylphenyl)azo]benzoic acid, and 4‐[(4‐hydroxy‐2‐pentadecyl phenyl)azo]benzoic acid (PSCpHBA) with p‐HBA were measured by the Maker fringe technique. The thermal and liquid‐crystalline (LC) phase behaviors of the polymers were examined by differential scanning calorimetry, a thermal‐stimulated polarization current, and polarized light microscopy. The polymers except PSCpHBA exhibited nematic‐threaded and Schlieren textures. The LC orientations give rise to an enhanced NLO response. The polymers had high thermal and temporal stabilities for second‐harmonic generation activity because of their rigid aromatic backbone. This study suggests that the rigid aromatic main chain exhibiting an LC phase is a promising simple method to synthesize highly stable NLO polymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1527–1535, 2003     

Synthesis and characterization of poly[(methylsilylene ethynylenephenyleneethynylene)-co-(dimethylsilylene ethynylenephenyleneethynylene)]s

<正>A series of poly[(methylsilylene ethynylenephenyleneethynylene)-co-(dimethylsilylene ethynylenephenyleneethynylene)]s were synthesized by the incorporation of various ratios of methylsilylene to dimethylsilylene units into the polymer chain backbone.The resultant copolymers were soluble in a variety of common organic solvents at room temperature.The copolymers were characterized by FT-IR,~1H-NMR,GPC,rheological analysis,differential scanning calorimetry(DSC) and thermogravimetric analysis(TGA).The results showed that the copolymers exhibited good processability and cured at low temperatures like 200℃.The curing reactions involved in hydrosilylation of Si—H and alkyne groups and the polymerization of alkynes.Y_(d5)(5%weight loss) of the cured copolymers ranged from 629℃to 686℃,and the decomposition residues of cured copolymers at 1000℃ranged from 88.1%to 90.9%under nitrogen.Thermal stability of the copolymers increased with the introduction of methylsilylene units into polymer chains.The cured copolymers were sintered at 1450℃,and the results of X-ray diffraction analysis showed that β-SiC was formed in the sintered products.     

Synthesis and second-order nonlinear optical properties of a crosslinkable functionalized hyperbranched polymer

A new implementation of copper-free thermal Huisgen 1,3-dipolar crosslinking reaction into a high T_g hyperbranched polyimide polymer in order to stabilize the electro-optic (EO) activity of second-order non linear materials is reported. Towards this goal, two different synthetic approaches were explored. The first strategy is based on the post-functionalization of the polymer with mixtures of DR1 azido derivative and propargylic alcohol, whereas, the second consists in the preparation of two complementary functionalized hyperbranched polymers that are mixed just before the preparation of films. Materials exhibit good second-order nonlinear optical coefficients (d₃₃) close to 30 pm/V at the fundamental wavelength of 1064 nm. Moreover, the thermal stability of the NLO properties of these materials reaches temperatures as high as 150 °C, and probably higher. This represents the highest thermal stability of crosslinkable EO polymers based on the crosslinking Huisgen reaction.     

丙烯酸接枝邻苯二酚衍生物的二次聚合

合成了2种聚合前驱体邻苯二丙烯酸酯(o-PDA)和2-甲氧基苯丙烯酸酯(2-MOPA), 分别通过与丙烯酸(AA)自由基共聚得到邻苯二丙烯酸酯-丙烯酸共聚物(O1)和2-甲氧基苯丙烯酸酯-丙烯酸共聚物(O2). 产物邻苯二酚(o-DHB)-O1(质量比1∶1)和1-羟基-2-甲氧基苯(HMOB)-O2(质量比1∶1)分别在乙腈/二氯甲烷-三氟化硼乙醚体系中直接阳极氧化聚合获得交联网状共聚物P1和P2. P1和P2均可溶于DMSO, 而难溶于ACN, DCM和THF等有机溶剂. 通过UV-Vis, FTIR和 ¹H NMR对交联共聚物膜的结构进行了表征. AA的引入不仅可以增加链的柔韧性, 而且提高了共聚物的力学性能. 而o-DHB/ HMOB的引入极大地减弱了单体的聚合位阻, 实现了单体的二次聚合, 同时也增强了单体及聚合物的电化学活性. 荧光光谱显示, 得到的2种交联共聚物膜分别在415和487 nm处有较强的发射峰, 表明共聚物仍具有良好的蓝色发光性能, 且聚丙烯酸结构的引入并没有对聚邻苯二酚(Po-DHB)和聚(1-羟基-2-甲氧基苯)(PHMOB)产生较大的荧光猝灭作用. 热重分析曲线(TGA)表明2种交联共聚物膜均具有较高的热稳定性.     

Synthesis of molecular imprinted organic-inorganic hybrid polymer binding caffeine

Random copolymers of poly{(methacrylamide)-co-(vinyl trimethoxysilane)} and poly{(methacrylic acid)-co-(vinyl trimethoxysilane)} were synthesized via a free radical polymerization reaction. Acid catalyzed sol-gel process of tetraethylorthosilicate (TEOS) with aforementioned polymers in the presence of methyl xanthine class of alkaloid like caffeine resulted in the formation of highly transparent monoliths. Solvent extraction of the template leaves behind the recognition sites intact with high selectivity towards the print molecule. The ionic and non-specific adsorptions, which are considered to be the main disadvantages of the molecularly imprinted polymers (MIP), are prevented to a considerable extent by the end capping of surface silanol groups. The template binding efficiencies of MIP were determined by HPLC analysis.     

一种新型二阶非线性光学功能分子及其交联聚氨酯材料的合成

合成了新型的含有偶氮和噻吩环的二阶非线性光学功能分子, 用红外光谱、紫外光谱、核磁共振和质谱确定了其结构; 制备了含有该功能分子的两种交联型聚氨酯聚合物薄膜, 当测量波长为1 064 nm时,  用Marker条纹法测得的二阶非线性光学系数d33值分别为80.6 pm/V(发色团的数密度为0.91×1020 Molecules/cm3)和20.1 pm/V(发色团的数密度为2.21×1020 Molecules/cm3); 聚合物Ⅱ的取向热稳定性达到了152 ℃.