A complementary and synergistic effect of Fe-Zn binary metal oxide in the process of high-temperature fuel gas desulfurization

57Fe Mossbauer spectroscopy was used to investigate the evolution of Fe-Zn binary metal oxide sorbent in the process of high-temperature fuel gas desulfurization. The results of phase analyses show that Fe-Zn binary metal oxide sorbent is rapidly reduced in hot fuel gas and decomposed to new phases of highly dispersed microcrystalline elemental iron and zinc oxide, both of which become the active desulfurization constituents. A complementary and synergistic effect between active iron acting as a high sulfur capacity constituent and active zinc oxide acting as a deep refining desulfurization constituent exists in this type of sorbent for hot fuel gas desulfurization.     

担载型钴镍金属氧化物催化剂上CH4还原NO反应研究

ＮＯｘ是大气的主要污染物之一,近年来,利用甲烷选择还原ＮＯｘ引起了广泛关注,研究发现,Ｃｏ、Ｍｎ和Ｎｉ离子交换的ＺＳＭ－５分子筛具有较高的活性［１～３］．但金属离子交换的分子筛催化剂有热稳定性差、易失活等缺点．最近已有金属氧化物用作甲烷还原ＮＯｘ反应...     

Ga2O3催化剂上CO2气氛中丙烷脱氢反应的研究

考察了Ga2O3对于丙烷脱氢和CO2气氛脱氢反应的催化性能,结果表明,Ga2O3具有较高的催化活性,其性能优于传统的Cr2O3脱氢催化剂,催化反应可能经过了一个丙烷异裂的过程,其中CO2是通过逆水煤气反应和Boudouard反应来促进催化剂性能的,在高于823K时该促进作用更为明显,催化剂的催化活性和其表面酸密度密切相关,在Ga2O3结构中,四配位Ga^3＋是其酸位的来源,并通过质子与氧化物的共同作用促进反应进行,催化剂的失活是由于表面的积碳和活性氧的消耗共同造成的,同时还对Ga2O3作为丙烷脱氢反应的催化剂的催化反应机理进行了初步探讨。     

Effect of pretreatment of graphite oxide on activity of platinum supported catalysts in liquid-phase hydrogenation

The effect of the reduction procedure of graphite oxide (GO) on activity of platinum supported catalysts in liquid-phase hydrogenation of nitrobenzene and dec-1-ene was studied. The following methods were applied to prepare the catalysts: simultaneous reduction of graphite oxide and H₂PtCl₆; deposition of platinum on graphite oxide which was preliminary subjected to reduction with sodium tetrahydroborate or hydrazine hydrate, or to thermal reduction at 1000 and 1050 °С. It was shown that at equal Pt particles size of ca. 2 nm the catalyst supported on thermally reduced graphite oxide is more active in the model reactions than the catalysts supported on chemically reduced graphite oxide. The catalyst prepared by simultaneous reduction was the least active.     

Determination of the chemical nature of active surface sites present on bulk mixed metal oxide catalysts

CH3OH temperature programmed surface reaction (TPSR) spectroscopy was employed to determine the chemical nature of active surface sites for bulk mixed metal oxide catalysts. The CH3OH-TPSR spectra peak temperature, Tp, for model supported metal oxides and bulk, pure metal oxides was found to be sensitive to the specific surface metal oxide as well as its oxidation state. The catalytic activity of the surface metal oxide sites was found to decrease upon reduction of these sites and the most active surface sites were the fully oxidized surface cations. The surface V5+ sites were found to be more active than the surface Mo6+ sites, which in turn were significantly more active than the surface Nb5+ and Te4+ sites. Furthermore, the reaction products formed also reflected the chemical nature of surface active sites. Surface redox sites are able to liberate oxygen and yield H2CO, while surface acidic sites are not able to liberate oxygen, contain either H+ or oxygen vacancies, and produce CH3OCH3. Surface V5+, Mo6+, and Te4+ sites behave as redox sites, and surface Nb5+ sites are Lewis acid sites. This experimental information was used to determine the chemical nature of the different surface cations in bulk Mo-V-Te-Nb-Ox mixed oxide catalysts (Mo(0.6)V(1.5)Ox, Mo(1.0)V(0.5)Te(0.16)Ox, Mo(1.0)V(0.3)Te(0.16)Nb(0.12)Ox). The bulk Mo(0.6)V(1.5)Ox and Mo(1.0)V(0.5)Te(0.16)Ox mixed oxide catalytic characteristics were dominated by the catalytic properties of the surface V5+ redox sites. The surface enrichment of these bulk mixed oxide by surface V5+ is related to its high mobility, V5+ possesses the lowest Tammann temperature among the different oxide cations, and the lower surface free energy associated with the surface termination of V=O bonds. The quaternary bulk Mo(1.0)V(0.3)Te(0.16)Nb(0.12)Ox mixed oxide possessed both surface redox and acidic sites. The surface redox sites reflect the characteristics of surface V5+ and the surface acidic sites reflect the properties normally associated with supported Mo6+. The major roles of Nb5+ and Te4+ appear to be that of ligand promoters for the more active surface V and Mo sites. These reactivity trends for CH3OH ODH parallel the reactivity trends of propane ODH because of their similar rate-determining step involving cleavage of a C-H bond. This novel CH3OH-TPSR spectroscopic method is a universal method that has also been successfully applied to other bulk mixed metal oxide systems to determine the chemical nature of the active surface sites.     

Asymmetric selective copolymerization of propylene oxide with d-camphoric acid anhydride

The ring-opening copolymerization of propylene oxide with d-camphoric acid anhydride [α]_D ?3.4° was carried out with diethylzinc and triethylamine as catalysts. It was found that the products were alternating copolymers which were optically active. The optical rotatory dispersion curves were found to fit a simple Drude equation having a λ_c value of 201 mμ. The specific rotation increased with increasing intrinsic viscosity of the product. The propylene oxide recovered from the polymerization system was optically active. Its specific rotation increased with increasing polymerization time. It is thought that the asymmetric selective copolymerization of propylene oxide is caused by the influence of the optically active camphoryl group of the polymer end.     

Effect of silicon oxidation on long-term cell selectivity of cell-patterned Au/SiO2 platforms

Cellular patterning on silicon platforms is the basis for development of integrated cell-based biosensing devices, for which long-term cell selectivity and biostability remain a major challenge. We report the development of a silicon-based platform in a metal-insulator format capable of producing uniform and biostable cell patterns with long-term cell selectivity. Substrates patterned with arrays of gold electrodes were surface-engineered such that the electrodes were activated with fibronectin to mediate cell attachment and the silicon oxide background was passivated with PEG to resist protein adsorption and cell adhesion. Three types of oxide surfaces, i.e., native oxide, dry thermally grown oxide, and wet thermally grown oxide, were produced to illustrate the effect of oxide state of the surface on long-term cell selectivity. Results indicated that the cell selectivity over time differed dramatically among three patterned platforms and the best cell selectivity was found on the dry oxide surface for up to 10 days. Surface analysis results suggested that this enhancement in cell selectivity may be related to the presence of additional, more active oxide states on the dry oxide surface supporting the stability of PEG films and effectively suppressing the cell adhesion. This research offers a new strategy for development of stable and uniform cell-patterned surfaces, which is versatile for immobilization of silane-based chemicals for preparation of biostable interfaces.     

氧化镧对HDPE热氧化分解行为的影响

聚合物改性是聚合物结构与性能研究中的一个重要领域,而稀土元素具有4f0-145dl-106s2的电子构型,由于4f轨道的特殊性和5d轨道的存在,稀土离子具有丰富的电子能级,离子半径较大,电荷较高,又有较强的络合能力,可对多种聚合物的热稳定性产生影响[1,7].     

Promoter effect of La_2O_3 on gold catalyst with different textural structures

Silica supported gold nanoparticles were synthesized and promoted by lanthanum oxide as dopant. The influences of La_2O_3 and silica textural structure on the gold dispersion, formation of active species, crystalline composition and the reacting role of dopants were studied in detail. The characterization results suggested that the dispersion of gold nanoparticles depended on the textural structure of silica without lanthanum oxide doping where small mesopores are more preferable to disperse gold nanoparticles. The addition of lanthanum oxide largely increased the dispersion of gold nanoparticles and oxygen active sites independent of the textural structure of silica support. The interaction between lanthanum oxide and silica enhanced by the synergy facilitated the release of oxygen vacancies and transition of active oxygen species. In addition, the chemical properties were greatly changed after lanthanum oxide addition which was only inconspicuously impacted by the initial textural structure of silica supports, shedding light on the further design of economic gold catalyst based on simple synthesis method.     

CuO／活性炭和Fe2O3／活性炭催化还原NO

ＣｕＯ／活性炭和Ｆｅ_２Ｏ_３／活性炭催化还原ＮＯ高志明，赵震，杨向光，吴越（中国科学院长春应用化学研究所长春１３００２２）关键词活性炭，还原，ＮＯ，氧化铜，氧化铁目前，对固定源的ＮＯ处理是采用Ｖ２Ｏ５／ＴｉＯ２作催化剂，ＮＨ３作还原剂的选择催化还原方...     

Hydrous manganese oxide/carbon nanotube composite electrodes for electrochemical capacitors

A novel type of composite electrode based on hydrous manganese oxide and a single-walled carbon nanotube has been prepared and used in electrochemical capacitors. Cyclic voltammetry, galvanostatic charging/discharging tests and electrochemical impedance measurements were applied to investigate the performance of the composite electrodes with different ratios of hydrous manganese oxide and single-walled carbon nanotube. For comparison, the performance of pure hydrous manganese oxide and pure carbon nanotubes was also studied. In this way, the composite electrode with a 6:4 ratio of hydrous manganese oxide to carbon nanotube was found to be the most promising active material for an electrochemical capacitor, which shows both good capacitance and power characteristics.     

Effect of the perfluoroalkyl groups on the preparation of carbon-based transparent and conductive thin films from silylated graphite oxides

Carbon-based transparent thin films were prepared from the pyrolysis of silylated graphite oxide containing perfluoroalkyl groups. The saturated amount of n-hexadecylamine molecules which accommodated between the layers of silylated graphite oxide containing larger pefluoroalkyl groups was smaller than that observed for silylated graphite oxide without perfluoroalkyl groups. The resulting intercalation compounds were dispersed in a chloroform/cyclohexane solution and precursor thin films were obtained by a cast method. The sheet resistance of the obtained carbon-based films was about 5 times smaller than that of the films prepared from silylated graphite oxide prepared with the analogous hydrocarbon substituents. The spectroscopic measurements indicated that the number of defects within the carbon layers was larger, however, that of carbon atoms participating π-conjugating system was larger. This probably ascribed to the active fluorine species formed as the result of thermal decomposition of perfluoroalkyl groups. The latter was responsible for the lower sheet resistance of carbon-based thin films.     

Polymerization of ethylene oxide with potassium-graphite inclusion compounds

The polymerization of ethylene oxide (EO) in tetrahydrofuran (THF) initiated by inclusion compounds of potassium in graphite (C₂₄K) at 50°C was studied. During the initial slow stage of the polymerization the catalyst efficiency increases, while during the second rapid stage the reaction proceeds at a constant concentration of the active centers. The influence of the catalyst and monomer concentrations on the concentration of the active centers and on the catalyst efficiency was studied. The existence of the slow stage is explained by diffusion of ethylene oxide between the graphite planes, where both initiation and initial chain growth take place. The diffusion of the growing chains from the catalyst into the solution brings about the formation of a necessary concentration of active centers in the solution, which ensures the rapid growth of the polymer chains under homogeneous conditions. An x-ray study of the catalyst after polymerization shows a strongly disturbed crystal structure of the graphite. Poly-(ethylene oxide) obtained at a higher degree of conversion, does not contain low molecular weight fractions.     

Cycloaddition of CO2 to epoxides catalyzed by polyaniline salts

The catalytic activity of polyaniline-HX (X=I, Br, Cl) (PANI-HI, PANI-HBr, PANI-HCl) for the cycloaddition of CO2 to propylene oxide (PO) to produce propylene carbonate (PC) was studied for the first time. It was shown that all the PANI salts were active for the reaction, and PANI-HI was most active and selective. On the basis of the preliminary results, the effect of the reaction conditions on the cycloadditions of CO2 to propylene oxide and epichlorohydrin was further investigated by using PANI-HI as the catalyst. The results indicated that the optimized temperature was around 115 degrees C. The maxima occurred in yield versus pressure curves at about 5 MPa for both substrates. Complete conversion was achieved in 3 h for epichlorohydrin and 6 h for propylene oxide at 115 degrees C and 5 MPa. With propylene oxide as the substrate, the reusability of PANI-HI was evaluated and no loss of catalytic activity was detectable after the catalyst had been reused five times. The catalyst was characterized by thermogravimetric analysis (TGA) and scanning electron microscopy (SEM), which provided further evidence for the high stability of the catalyst. We believe that the catalyst has great potential for industrial applications because it has some unusual advantages, such as its easy preparation, high activity, selectivity, stability, low cost, and simple separation from products.     

The structure of active sites in a molybdenum/zeolite catalyst for methane dehydroaromatization: a DFT study

Mononuclear active sites in molybdenum-zeolite catalysts for methane dehydroaromatization were studied within the framework of the density functional theory (DFT). The optimized structures of mononuclear sites in molybdenum oxide, molybdenum oxycarbide, and molybdenum carbide were obtained. A mechanism of carbidization i.e., formation of molybdenum oxycarbide and molybdenum carbide from molybdenum oxide was proposed. Carbidization using three (radical, cationic, and anionic) structures of mononuclear active sites was studied. It was found that the anionic structure provides the best conditions for methane activation on the mononuclear active site.     

Functions of Acyclic Poly(ethylene Oxide) Homologs: Acceleration of Nucleophilic Reactions and Selective Ion Transport through Membranes

The acceleration effect of poly(ethylene oxide) on nucleophilic reactions was investigated. The enhancement of the reaction rate was interpreted by the cooperative solvation of alkali metal ions with ethereal oxygens of PEO resulting in active nucleophilic anions. In relation to the complex formation of alkali metal ions with PEO, the oligo(ethylene oxide) derivatives were prepared as the synthetic ionophores, which were able to transport alkali metal ions selectively through a liquid membrane against the alkali metal ion concentration.     

The morphology modulation of graphene to produce wrinkles and folds for effective electrochemical determination of Hg(II)

A highly efficient electrode material, three-dimensional reduced graphene oxide with varying wrinkles and folds (WRGO), applicable for electrochemical determination of Hg(II) was obtained by treating graphene oxide (GO) with KOH aqueous solution. After alkaline etching, the relatively flat graphene was altered and its self-aggregation was significantly alleviated, producing more wrinkles and folds, which provided more active adsorption sites for heavy metal ions. WRGO-5 modified electrode system herein offers a highest sensitivity of (31.83 μAμM⁻¹) and a lowest LOD of (16.28 nM). Moreover, the electrode sensor possesses good stability and reproducibility.     

Adsorption of selected ions on hydrous cerium oxide

Hydrous cerium oxide was synthesized and laboratory study was conducted to address its applicability for decontamination of barium, strontium, molybdenum, europium, iodine, samarium and cesium ions from radioactive liquid wastes using radiotracer technique. The adsorption of Ba(II), Sr(II), Mo(II), Eu(II), I(I), Sm(III) and Cs(I) on hydrous cerium oxide has been investigated as a function of pH, concentration and temperature of the adsorptive solution and the result obtained show that these parameters affect the extent of adsorption. The ion-exchange capacity decreased at higher temperatures which could be due to decrease of active sites as well as hydrophilic properties of surface adsorbent. Hydrous cerium oxide shows relatively high adsorption in acidic and neutral media towards the radiotracers studied, which can be attributed to large hydrated radius and ion exclusion effect.     

Au/SiO(2) as a highly active catalyst for the selective oxidation of silanes to silanols

Au/SiO(2), which was prepared properly to have a high dispersion of gold nanoparticles, acts as an extremely active catalyst for the selective oxidation of a variety of silanes. It outperforms other reducible oxide supported gold catalysts thanks to the affinity of the silica support to the silane substrate.