纳米Ag/ZnO光催化剂及其催化降解壬基酚聚氧乙烯醚性能

采用氨浸法制备了不同Ag负载量的纳米Ag/ZnO光催化剂,并用X射线衍射、比表面积测定、X射线光电子能谱和漫反射紫外-可见光谱测定了Ag/ZnO的晶型结构、比表面积、表面组成和光谱特征.以壬基酚聚氧乙烯醚(NPE-10)为模型污染物,分别在紫外光和可见光照射下考察了纳米Ag/ZnO的光催化活性.结果表明,Ag能成功地负载到ZnO表面,且随着Ag负载量的增加,ZnO的粒径逐渐增大,比表面积逐渐减小.与纳米ZnO样品相比,Ag/ZnO中Ag 3d5/2结合能减小,而Zn 2p和O 1s结合能增大,ZnO表面的羟基氧和吸附氧含量增加.当Ag负载量大于0.5%时,Ag/ZnO样品的吸收光谱发生红移,在可见光区出现吸收.光催化降解结果表明,0.5%Ag/ZnO样品的光催化活性最高,在紫外光和可见光照射3 h后NPE-10降解率分别约为77%和56%,而ZnO样品的光催化活性仅约为61%和40%.     

纳米V2O5／ZnO光催化剂对壬基酚聚氧乙烯醚降解的催化活性

采用氨浸法制备了不同V2O5含量的纳米V2O5/ZnO光催化剂,并用X射线衍射、比表面积测定、透射电镜、X射线光电子能谱和漫反射紫外-可见光谱测定了催化剂的晶型、比表面积、形貌尺寸、表面组成和光谱特征.以壬基酚聚氧乙烯醚(NPE-10)为模型污染物,分别在紫外光和可见光照射下考察了光催化剂的催化活性.结果表明,随着V2O5含量的增加,V2O5/ZnO的粒径逐渐减小,比表面积逐渐增大.与纳米ZnO样品相比,V2O5/ZnO中V2p的结合能减小,而Zn2p和O1s的结合能增大,V2O5/ZnO表面的羟基氧和吸附氧含量增加.n(V)/n(Zn)=2·5%的V2O5/ZnO光催化剂样品的催化活性最高(在紫外光和可见光照射3h后,NPE-10降解率分别约为79%和62%).     

ZnO纳米柱状阵列表面AgX等离子基元修饰及其可见光光催化活性

采用浸渍法制备了表面AgX（X=I,Br）等离子基元修饰的ZnO纳米柱状阵列,研究了浸渍浓度和时间以及紫外光光照预处理对ZnO纳米柱状阵列可见光光催化活性的影响.采用场发射扫描电子显微镜、X射线衍射仪、紫外可见漫反射吸收光谱以及X射线光电子能谱仪等手段对ZnO纳米柱状阵列的形貌、相组成、禁带宽度及其表面特性进行了表征.结果显示,AgBr颗粒分布于ZnO纳米柱状阵列的顶端及顶端侧面,同时AgBr颗粒之间相互接触而形成网状结构.通过紫外光光照预处理,AgBr表面出现细小颗粒,形成Ag/AgBr/ZnO纳米复合结构.可见光光催化降解甲基橙结果表明,在相同工艺条件下所制AgBr/ZnO的可见光光催化活性明显优于AgI/ZnO,且与浸渍浓度及时间有关.由于ZnO纳米柱状阵列的比表面积大,AgBr的可见光响应特性以及Ag/AgBr纳米结构的表面等离子效应,经过紫外光光照预处理形成的Ag/AgBr/ZnO纳米复合结构表现出最好的可见光光催化活性.     

ZnO/Ag微米球的合成与光催化性能

用微波辅助多元醇法对预先制备的ZnO微米球进行修饰,合成了载银氧化锌微米球（ZnO/Ag）. 利用X射线衍射仪、场发射扫描电子显微镜、透射电子显微镜、X射线光电子能谱仪、紫外-可见双光束分光光度计和光致发光光谱仪等对样品的结构、形貌和光学性能进行了表征. 在紫外光照射下,通过亚甲基蓝的降解反应研究了样品的光催化活性. 结果表明,所制备的ZnO/Ag微米球是由面心立方的Ag纳米颗粒附着在纤锌矿结构的ZnO球表面形成;与ZnO相比,ZnO/Ag的紫外-可见光吸收光谱发生明显红移,在紫外和可见光范围均有较强的吸收;随着Ag含量的增加,ZnO/Ag荧光光谱强度先减弱后增强;与ZnO相比,ZnO/Ag的光催化活性明显提高,AgNO₃ 浓度为0.05 mol/L时制得的ZnO/Ag光催化活性最高.     

ZnO纳米管的光学性质及其对甲基橙降解的光催化活性

以十二烷基硫酸钠为模板剂采用水热法合成了ZnO纳米管,以尿素和ZnSO4为原料制备了ZnO纳米颗粒,并应用透射电镜、x射线衍射、光致发射光谱、拉曼光谱、比表面积测定、傅里叶红外光谱和紫外-可见漫反射光谱等技术对样品进行了表征.结果表明,ZnO纳米管的比表面积较大,在λ≈650nm的可见光波段ZnO纳米管开始出现吸收峰,而ZnO纳米颗粒在可见光波段几乎没有吸收.ZnO纳米管和纳米颗粒在紫外光照射下均对甲基橙有降解作用,其中ZnO纳米管的光催化活性较高.随着催化剂用量的增加和光照时间的延长,甲基橙降解率逐渐提高;甲基橙浓度的增大使甲基橙降解率降低.     

一步火焰辅助热解法制备Fe掺杂嵌碳TiO2及其光催化性能

以钛酸四丁酯、无水乙醇和无水氯化铁为前驱体,通过一步火焰辅助热解法制备了Fe掺杂嵌碳TiO₂,并研究了样品的光催化活性. 利用扫描电子显微镜及能谱、X射线光电子能谱、X射线粉末衍射和紫外-可见漫反射吸收光谱等对样品的形貌、组分、晶型和光吸收进行了表征,并研究了样品在紫外和可见光下的光催化活性. 结果表明,无需后续热处理可直接得到主要是锐钛矿相TiO₂的样品,Fe³⁺以替位掺杂形式进入TiO₂晶格,随掺杂量增加,样品在可见光区域的吸光度提高,吸收带边红移. Fe掺杂量（摩尔分数）小于0.2%可改善样品的光催化活性,当Fe掺杂量为0.1%时,样品在可见光和紫外-可见光照射下均显示出最高的降解亚甲基蓝速率.     

WO3/ZnO复合光催化剂的制备及其光催化性能

采用沉淀-研磨法制备了一系列不同WO3含量的WO3/ZnO复合光催化剂,应用N2物理吸附、X射线衍射、扫描电镜、傅里叶变换红外光谱、紫外-可见光谱和光致发光谱等手段对催化剂进行了表征,并以λ=365nm的紫外光为光源,评价了该催化剂光催化降解酸性橙Ⅱ的活性,考察了WO3的复合对WO3/ZnO样品光催化性能的影响.结果表...     

Pt/BiOCl纳米片的制备、表征及其光催化性能

采用光化学沉积法制备了一系列不同Pt含量的新型Pt/BiOCl纳米片光催化剂,运用N2物理吸附-脱附、X射线粉末衍射、扫描电镜、透射电镜、X射线光电子能谱、光致发光光谱、紫外-可见漫反射光谱等手段对Pt/BiOCl进行了表征,并以λ=254nm的紫外灯和钨灯为光源,考察了Pt含量对Pt/BiOCl光催化降解酸性橙II活性的影响.结果表明,沉积的Pt对BiOCl样品比表面积的影响不大,但可有效增强催化剂对可见光的吸收能力,显著抑制光生电子与空穴的复合.当Pt含量为1%~2%时,能大幅度提高紫外光下BiOCl催化降解染料的活性,并产生可见光活性.这是由于Pt/BiOCl具有一定的可见光吸收能力,产生了Pt纳米粒子的等离子体光催化作用.     

用TiO2，ZnO及Fe2O3纳米粒子光催化氧化庚烷的反应

 制备了三种n－型半导体氧化物TiO2，ZnO和Fe2O3纳米粒子，用X射线衍射和N2吸附技术分别对它们的结构及比表面积进行了表征．考察了三种氧化物粒子对庚烷的气相光催化氧化反应的催化活性．研究表明，对于同种催化剂，随着焙烧温度的升高，催化剂的粒径增大，比表 面积减小，光催化活性下降．三种催化剂纳米粒子的光催化活性顺序为TiO2（锐钛矿）＞ZnO＞Fe2O3，金红石型TiO2粒子的催化活性低于ZnO粒子．结合能带理论探讨了三种催化剂光催化活性差异的原因．     

CTAB作用下纳米复合材料Ag/ZnO-SnO2的制备与光催化降解罗丹明B

在模板剂溴化十六烷基三甲基胺(CTAB)作用下,采用溶胶-凝胶法再结合程序升温溶剂热法制备了纳米复合材料Ag/ZnO-SnO2(CTAB),其中Ag,Zn,Sn摩尔比为0.1∶2∶1.利用X射线衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)、扫描电子显微镜配合X射线能量色散谱(SEM-EDS)和N2吸附-脱附测定等方法对复合材料的组成、结构及形貌等进行了表征.结果表明,该复合材料具有纤锌矿和金红石结构,Ag以单质形式存在.与未经CTAB作用的样品相比,Ag/ZnO-SnO2(CTAB)颗粒分布更均匀,且呈现规则的纳米棒状结构.复合材料在紫外光和可见光作用下对罗丹明B(RhB)的光催化降解结果显示,样品Ag/ZnO-SnO2(CTAB)的光催化活性明显高于Ag/ZnO-SnO2、ZnO-SnO2、ZnO和商用P-25.     

Fe-Ni 共掺杂 ZnO 的制备及其光催化降解甲基橙活性

 采用溶液法制备了 Fe-Ni 共掺杂 ZnO 光催化剂, 并运用 X 射线衍射、扫描电镜和原子发射光谱等对催化剂进行了表征. 以甲基橙 (MO) 为模型污染物, 评价了样品的光催化活性, 考察了甲基橙初始浓度及其 pH 值, 以及催化剂用量等对光催化反应性能的影响. 结果表明, Fe-Ni 共掺杂降低了 ZnO 的结晶度, 并促进了晶粒的长大. 光催化降解反应表明, Fe-Ni 共掺杂显著提高了 ZnO 光催化降解甲基橙的活性, 当催化剂用量为 0.6 g/L, 经 120 min 紫外光照射时, 可使甲基橙溶液 (10 mg/L) 降解率达到 93.5%. 关键词：铁; 镍; 共掺杂; 氧化锌; 光催化; 甲基橙; 降解     

Band structure tuning of ZnO/CuO composites for enhanced photocatalytic activity

The toxic dye pigments, even in small quantities, can damage ecosystems. Removing organic, inorganic, and microbiological contaminants from wastewater via heterogeneous photocatalysis is a promising method. Herein, we report the band structure tuning of ZnO/CuO nanocomposites to enhance photocatalytic activity. The nanocomposites were synthesized by a chemical approach using step-wise implantation of p-type semiconductor CuO to n-type semiconductor ZnO. Various characterization techniques such as X-ray diffraction analysis (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X-ray analysis (EDX) and UV spectroscopy were used to investigate the crystal structure, surface morphology, elemental composition and optical properties of the synthesized samples. As the CuO content increased from 10% to 50% in ZnO/CuO nanocomposites, the optical bandgap decreased from 3.36 to 2.14 eV. The photocatalytic activity of the samples was evaluated against the degradation of methylene blue (MB) under visible irradiation. Our study demonstrates a novel p–n junction oxide photocatalyst based on wt. 10% CuO/ZnO with superior photocatalytic activity. Effectively 66.6% increase in degradation rate was achieved for wt. 10% CuO/ZnO nanocomposite compared to pure ZnO nanoparticles.     

Ag改性纳米ZnO薄膜及光催化活性

采用溶胶-凝胶法和光还原沉积贵金属法结合制备出Ag改性的纳米ZnO薄膜。利用FESEM、XPS、ESR、UV-Vis分析了纳米Ag-ZnO薄膜的表面形貌、表面组成和光谱特征。FESEM分析表明银在纳米ZnO薄膜表面形成原子簇而没有形成均匀覆盖层。XPS分析表明负载在纳米ZnO薄膜表面的银以Ag⁰形式存在; 相对于纳米ZnO薄膜, 纳米Ag-ZnO薄膜中晶格氧的含量有所下降,而表面羟基氧和吸附氧的含量显著增加。纳米Ag-ZnO薄膜的ESR峰强比纳米ZnO薄膜大,表明纳米Ag-ZnO薄膜中束缚单电子的氧空位的浓度高于纳米ZnO薄膜。UV-Vis分析纳米Ag-ZnO薄膜的紫外可见吸收光谱可能是纳米银粒子与纳米ZnO薄膜共同作用的结果。以甲基橙为模拟污染物,考察了纳米Ag-ZnO薄膜的光催化活性以及银沉积量对催化剂活性的影响。光催化降解结果表明,银的沉积量为0.018 2 mg·cm^-2的纳米Ag-ZnO薄膜的光催化活性最高,在紫外光照射3 h后甲基橙降解率约为78%,而纳米ZnO薄膜约为62%。     

Microwave-assisted synthesis of ZnO and its photocatalytic activity in degradation of CTAB

Nanosized zinc oxide (nano-ZnO) was prepared by a microwave irradiation method using zinc nitrate and triethanolamine as starting materials and distilled water as a solvent. The as-prepared powder was characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The photocatalytic degradation of cetyltrimethylammonium bromide (CTAB) using the prepared material under UV irradiation was studied.The effects of ZnO dosage and initial pH on the photodegradation of CTAB were investigated. As the ZnO load increased, the CTAB degradation first increased and then decreased. The optimum ZnO dosage was 3 g L^–1. Photodegradation of CTAB is more efficient in slightly alkaline media (pH 9).     

Visible-light-induced photocatalytic performances of ZnO-CuO nanocomposites for degradation of 2,4-dichlorophenol

Nanostructured ZnO and CuO, and coupled oxides, i.e., ZnCu, Zn2Cu, and ZnCu2, with ZnO:CuO molar ratios of 1:1, 2:1, and 1:2, respectively, were successfully prepared through a simple, one-step, mi-crowave-assisted urea–nitrate combustion synthesis, without the use of organic solvents or surfac-tants. The prepared samples were characterized using X-ray diffraction, X-ray photoelectron spec-troscopy, scanning electron microscopy, energy-dispersive X-ray analysis, transmission electron microscopy, Fourier-transform infrared spectroscopy, diffuse reflectance spectroscopy, and photo-luminescence spectroscopy. The optical absorption of ZnO extended into the visible region after CuO loading. The photocatalytic activities of ZnO, CuO, and the coupled oxides were evaluated based on photodegradation of 2,4-dichlorophenol under visible-light irradiation. The coupled metal oxide Zn2Cu showed the best photocatalytic activity;this was mainly attributed to the extended photore-sponsive range and the increased charge separation rate in the nanocomposite. The photocatalytic degradation process obeyed pseudo-first-order kinetics. The results suggest that the coupled metal oxide Zn2Cu has potential applications as an efficient catalytic material with high efficiency and recyclability for the photocatalytic degradation of organic pollutants in aqueous solution under visible-light irradiation.     

Highly reusable chitosan-stabilized Fe-ZnO immobilized onto fiberglass cloth and the photocatalytic degradation properties in batch and loop reactors

The new design of the photocatalytic reactor is crucial to study for improving compatibility and scaling up the operation. A compatible loop photocatalytic reactor has been designed and used for rhodamine B decomposition. The photocatalysts were either ZnO or Fe-ZnO immobilized onto fiberglass cloth. The ZnO catalyst exhibited high crystallinity with or without Fe as the dopant. The crystallite size increased with the presence of Fe in the lattices. Most of the crystal parameters matched the standard ZnO data, and the cluster size was comparable to most reported studies. Diffuse Reflectance Spectroscopy (DRS) analysis confirmed the photon absorption shifted to the visible light range. The Fe dopant decreased the ZnO bandgap, and SEM-EDS confirmed the catalysts adhered to the fiberglass surface. The volume, thickness of the substrate solution, and reaction temperature influenced the photocatalytic-degradation rate. The photocatalytic degradation rate was higher under sunlight than ultraviolet irradiation. The reaction rate was lower in the batch reactor than in the loop reactor. The photocatalytic reaction almost completely mineralized RhB and changed the red solution to colorless. The immobilized photocatalyst has been reused more than 50 times without significantly decreasing the catalytic activity.     

Mesoporous Fe2O3-doped TiO2 nanostructured fibers with higher photocatalytic activity

Mesoporous Fe(2)O(3)-doped TiO(2) nanostructured fibers were fabricated through electrospinning the relevant gel precursor. The prepared fibers were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and surface analysis, respectively. The photocatalytic activity of these mesoporous composite fibers was evaluated by photocatalytic degradation of methylene blue (MB) in water under UV irradiation. Compared with different types of photocatalysts, the 1% Fe(2)O(3)-doped TiO(2) fibers exhibited super photocatalytic activity.     

交联累托石/Cu2O纳米复合材料的制备及可见光催化性能

以醋酸铜为原料, 交联累托石(CN-REC)为载体和模板, 制备了CN-REC /Cu₂O纳米复合材料. 利用X射线衍射(XRD)、透射电镜(TEM)、傅里叶变换红外(FTIR)光谱、紫外-可见漫反射光谱(UV-Vis DRS)等技术对复合材料的形貌、表面结构、层间微结构、光响应性能进行了研究. 结果表明: CN-REC对Cu₂O的形貌具有较好的调控作用, Cu₂O均匀分散负载于CN-REC的层间和片层表面; Cu₂O和CN-REC通过Si―O―Cu键发生相互作用; 复合材料的能带隙变宽、光响应能力增强. 以卤素灯为可见光光源, 活性艳红(X-3B)为目标污染物, 研究了复合材料的可见光催化性能, 结果表明, 光催化反应过程符合L-H动力学模型, 2 h内浓度为160 mg·L^-1的X-3B去除效率可超过80%.