PREPARATION OF POLYSULFONAMIDE/TiO_2 NANOCOMPOSITES BY SOL-GEL

1. INTRODUCTIONPolysulfonamide resin can be used to prepare heat-resistant fibers. The first investigation was started by the Chinese scientists in the 1970’s [1], then it is widely used in industry field. Its aerospace and fire protection application ha…     

A NEW KIND OF FIBER-SPUN FROM POLYSULFONAMIDE/ZINC SOLUTION

In this paper, we succeed in fabricating high-temperature fiber of polysulfonamide/ZnO. Polysulfonamide/ZnO nanocomposite was prepared by in-situ polymerization. Some studies and characterization of Polysulfonamide/ Zinc oxide nanocomposite with ZnO 0.5% have been done. It includes ηr,, Crystal degree and thermal property. Experiment＇s results showed that, ZnO as filler can improve crystal degree of polysulfonamide fiber. The crystal degree has been bnproved, from lower than 20% up to 27%. ηr of polysulfonamide/ Zinc oxide nanocomposite solution with ZnO 0.5% is 2.03. The maxinum weight loss of the nanocomposite occurred at 453.5 ℃.     

一种新型的铕络合物/TiO2发光薄膜

研究了Eu(DBM)3(DiBut-bpy)/TiO2/AA 单分子膜的表面压－分子面积(π－A)曲线和稳定性,单层膜中的TiO2纳米粒子是经TBT（tetrabutyloxyltitanium ,钛酸四丁酯）二维溶胶-凝胶法得到的.TiO2纳米粒子和铕络合物都被成功地转移到固体基片上，得到了具有良好的机械和热稳定性的新型发光薄膜.小角度X射线衍射结果证明这种复合膜具有层状有序的周期性结构.讨论了TiO2基质对复合膜发光机理的影响.     

PREPARATION OF POLYSULFONAMIDE AND MODIFIED TITANIUM OXIDE NANOCOMPOSITES BY IN-SITU POLYMERIZATION

1. INTRODUCTIONAlthough Polysulfonamide fibers have showed excellent high temperature resistance with Tg over 370℃ , their poor mechanical strength and easy broken character after the exposure of UV radiation, have limited their applications [1～3]. Titanium oxide nanoparticles were widely used as UV absorptive additives in textile materials and cosmetic industries because of its’ efficiency and harmless characters [4～6]. In our work, we used a kind of titanium oxide nanoparticles, w…     

利用Breath Figures法制备具有蜂窝状结构的 PMMA/TBT复合膜

以聚甲基丙烯酸甲酯(PMMA)和钛酸四丁酯(TBT)的氯仿溶液为铸膜溶液,采用Breath Figures法制备了蜂窝状结构的PMMA/TBT多孔阵列薄膜,采用SEM、JR、XRD对制备的多孔膜进行了表征,探讨了聚合物浓度、PMMA/TBT配比以及水解抑制剂对膜蜂窝状结构的影响.实验结果表明,起始溶液浓度为20～30m...     

PREPARATION OF POLYSULFONAMIDE AND MODIFIED TITANIUM OXIDE NANOCOMPOSITES BY IN-SITU POLYMERIZATION

A kind of new nano composite with ultraviolet (UV) ray resistance and high temperature stability was prepared by in-situ polymerization in low temperature. Polysulfonamide (PSA) was synthesized with 4, 4'-diaminodiphenyl sulfone (DDS) and terephthaloyl chloride (TPC) in the common solvent N, N-Dimethyl- -acetamide (DMAc). Nano filler is a certain nano titanium oxide modified by silicon oxide (TMS), which plays the role of UV resistance additives. Properties of the novel composite materials were characterized by Atomic Force microscopy (AFM), thermal gravimetric Analysis (TGA) and Ultraviolet Spectroscopy. AFM had showed the sizes and distributions of TMS particles in the nanocomposite. Ultraviolet Spectroscopy for the nanocomposites showed a large absorption in UV band. TGA showed the decomposition temperature was increased over ten degrees with 0.5% wt TMS for this nanocomposite compared with pure PSA.     

反应介质pH值和前驱体用量对PSt/TiO_2复合微球结构形态及TiO_2空心微球形貌的影响

首先用聚乙烯亚胺(PEI)对粒径为360 nm的单分散无皂聚苯乙烯(PSt)乳胶粒进行修饰,得到表面荷正电的PSt种子乳液,然后将其滴加到溶有钛酸正丁酯(TBT)的乙醇与水的混合介质中,通过溶胶-凝胶(sol-gel)法制备出了核壳结构PSt/TiO2复合微球,系统研究了体系pH和TBT用量对复合微球结构形态的影响.研究表明,酸性条件不利于核壳结构PSt/TiO2复合微球的形成;当体系pH值为7.2时,可得到包覆完整、TiO2壳层厚度均一的PSt/TiO2复合微球,此后随着体系pH值的升高,包覆厚度逐渐提高;当pH值升高到11.0时,壳层厚度达到最大,但出现了包覆层不完整的复合微球.在固定聚合体系pH为8.5,EtOH/H2O质量比为100/6,表面修饰PSt种子乳液用量为0.5 g(固含量为4%)的条件下,随着TBT用量从0.01 g增加到0.16 g,复合微球壳层厚度从约0 nm逐渐增加到60 nm;当TBT用量增加到0.32 g时,壳层厚度迅速降至12nm,微球表面变得粗糙,并出现大量未包覆微粒;此后随着TBT用量的增加,包覆层厚度逐渐减少,未包覆微球逐渐增多.结果显示,当复合微球中TiO2包覆层达到一定厚度时,经煅烧后才能得到形貌完整的TiO2中空微球.     

染料敏化的TiO2纳米管薄膜的光电浸润性

采用阳极氧化法在钛箔表面制备TiO2纳米管阵列, 并在其表面修饰N3染料(Ruthenium dye)作敏化剂, 用氟硅烷来提高表面疏水性, 获得超疏水薄膜. SEM测定结果表明, 纳米管薄膜具有各向异性浸润结构, 同时阳极氧化的非均匀性增加了表面的粗糙度. UV-Vis吸收光谱及电化学阻抗谱结果表明, 薄膜具有优异的光电性能. 通过施加超过一定阈值的电压, 液滴在薄膜表面由超疏水状态转变为亲水状态. 利用光电协同激励作用时, 阈值电压比单独使用电激励时降低了10 V, 这是使用高效的N3染料光电敏化层的结果.     

基于三维多孔石墨烯/含钛共轭聚合物复合多孔薄膜的柔性全固态超级电容器

采用Fe~(3+)离子交联的方法制备氧化石墨烯水凝胶,经化学还原制备出一种新型的三维多孔石墨烯薄膜材料命名为rGO-Fe;通过电化学聚合法在rGO-Fe基底上进一步制备了一种三维多孔石墨烯/含钛共轭聚合物复合薄膜材料,命名为r GO-Fe/P(EDOT:P3C)-1-Ti。作为一种新型复合薄膜材料,rGO-Fe/P(EDOT:P3C)-1-Ti较rGO-Fe具有更好的抗拉伸性能,平均厚度为3μm的rGO-Fe/P(EDOT:P3C)-1-Ti薄膜,可承受载荷拉力0.97 N,优于相同厚度的rGO-Fe薄膜(0.76 N)。将rGO-Fe/P(EDOT:P3C)-1-Ti薄膜作为自支撑电极制备了柔性全固态超级电容器,表现出优良的电容性能,且在弯折状态下仍能正常工作。当电流密度为0.1 A?g~(-1)时,该柔性全固态超级电容器的质量比容量为71.13?F?g~(-1),面积比容量为101 mF?cm~(-2),当电流密度为0.6 A?g~(-1)时,其质量比容量为18.14 F?g~(-1),面积比容量为25.8 mF?cm~(-2)。     

Determination of surface area and porosity of small, nanometer-thick films by quartz crystal microbalance measurement of gas adsorption

The Brunauer-Emmett-Teller (BET) surface area of 15 nm-thick films made of TiO2/polyelectrolyte bilayer was determined by quartz crystal microbalance (QCM) measurement of N2 and Ar adsorption isotherms at 77 K. The measurements were carried out using a home-built vacuum chamber that includes built-in 9 MHz QCM and cryostat units. As little as 1 ng of the adsorbed gas could be detected, and the BET surface area of a flat Au film (ca. 0.5 cm2) on an oscillator was determined within an experimental error of +/-5%. The titania/polymer composite film gives N2 and Ar adsorption isotherms consisting of a less-pronounced type-I curve and a break at around p/p0 = 0.7. This behavior is ascribed to the presence of irregular micropores and 6 nm phi-mesopores in the composite film. An analysis of the isotherms shows that the porosity of the composite film is about 12%, which is much smaller than that of bulk titania gel powder. The greater density appears to be related to the reported superior properties (robustness and resistance to electrical breakdown) of the organic/inorganic multilayer film. We conclude that the QCM-based, high-precision measurement of gas adsorption is a powerful tool for investigation of the detailed morphology of nanometer-thick films.     

新型聚N，N-二甲基苯胺/多壁碳纳米管修饰电极的制备、表征与应用

采用多壁碳纳米管(MWNT)改性聚N,N-二甲基苯胺(PDMA)膜,制备了新型复合膜修饰玻碳电极,并用SEM、电化学方法对修饰电极进行表征。 结果表明,无论MWNT是以掺杂还是先滴涂MWNT再聚合DMA多层修饰方式,均会改变PDMA膜的形貌和电化学性能。 复合膜修饰电极比单一PDMA膜修饰电极大幅度提高了比表面积和电活化面积,同时使PDMA和MWNT更好地协同发挥其优良的电化学特性。 实验结果表明,层层修饰制备的聚N,N-二甲基苯胺/多壁碳纳米管复合膜修饰电极对香草醛的电化学响应远大于基体电极和其它方法制备的修饰电极,电催化作用显著提高,其过电位降低了148 mV,氧化峰电流约增加了6倍;其电极反应是吸附控制的不可逆氧化过程,转移电子数n为2,质子数m为1,传递系数α为0.4062,吸附量为Γ=3.527×10-9 mol/cm2;检出下限为8.0×10-7 mol/L,样品平均回收率为99.87%。     

Multivariate optimization approach for the analysis of butyltin compounds in mussel tissues by gas chromatography-mass spectrometry

The derivatization with NaBEt(4) for the determination of butyltin compounds in mussel tissues (Mytilus galloprovincialis) by GC-MS was optimized using a central composite design. The effects of NaBEt(4) concentration, pH and acetate buffer concentration on the derivatization efficiency were considered. Solid-phase extraction with Florisil cartridges was performed, demonstrating that the clean-up drastically reduces the background and improves the sensitivity. The good accuracy of the method was verified on a certified reference material (ERM 477); the figures of merit for all the three analytes, evaluated under optimum conditions, were satisfactory. The optimized derivatization procedure was applied to the determination of the analytes in mussels exposed to tributyltin (TBT). All considered tissues showed considerable accumulation of TBT, especially gills.     

一步电沉积纳米铜/石墨烯/壳聚糖复合膜修饰玻碳电极测定邻苯二酚

用一步电沉积法制备了纳米铜/石墨烯/壳聚糖复合膜修饰玻碳电极。用循环伏安法(CV)和差分脉冲伏安法(DPV)对邻苯二酚在该修饰电极的电化学行为进行了研究。实验结果表明,在pH值为7.0的磷酸盐缓冲液(PBS)中,该修饰电极对邻苯二酚具有良好的电催化作用,其电化学信号与邻苯二酚的浓度在1.0×10-6～2.0×10-4mol/L范围内呈良好的线性关系,线性相关系数为0.991。检出限为1×10-7mol/L。结果表明,纳米铜/石墨烯/壳聚糖复合膜修饰电极显著提高了邻苯二酚的电化学响应信号,并表现出良好的选择性和重现性。该方法成功用于水样中邻苯二酚含量的测定。     

N,N-二甲氨基丙烯酸乙酯的制备

报道了一种以二甲氨基乙醇（DEAE）与丙烯酸丁酯（BA）为原料,钛酯四丁酯（TBT）为催化剂,在负压下反应及蒸馏,生产N,N－二甲氨基丙烯酸乙酯（OMAEA）的方法,并讨论了原料配比、催化剂用量、压力与温度及反应气氛对产物收率的影响,提出了优化的反应条件。     

Study on selective reflection properties of chiral nematic liquid crystalline composites with a non‐uniform pitch distribution

The preparation is reported of particles of photopolymerisable monomer/chiral dopant composites with a crystalline (Cr)‐chiral nematic (N*) phase transition. By mixing particles with different pitches of the N* phase in the Cr phase and crosslinking the liquid crystal (LC) monomer molecules by photopolymerisation in the planarly oriented N* phase, an N*‐LC composite film with a non‐uniform pitch distribution was obtained. Experimental results show that the bandwidth of the reflection spectrum and the location of reflection band of the composite films can be controlled accurately by controlling the pitch lengths of the N* phase of the particles. Effects of polymerisation temperature and UV intensity on the non‐uniform pitch distribution of N*‐LC composite films were investigated.     

Ag-PVA和Ag-PVA/TiO2复合超薄膜的制备及性能研究

用3种方法制备了银纳米粒子-聚乙烯醇复合体系,其中用加热还原法所得体系中Ag纳米粒子的尺寸较大(15nm),其表面等离子体共振吸收峰较宽,最大吸收波长位于420nm;用室温硼氢化钠还原法得到的复合体系的吸收峰蓝移至409nm,且峰形较窄,Ag纳米粒子的平均粒径为8.7nm;低温NaBH4还原法所得体系吸收峰进一步蓝移至397nm,此时Ag纳米粒子粒径最小(3.5nm).将室温还原法所得Ag-PVA复合体系旋涂成膜,所得薄膜光滑、透明、均匀性好,该法适用于制备多层薄膜,以调控薄膜的厚度和光谱性质.将Ag-PVA复合体系与钛酸四丁酯(Ti(O_nBu)₄)的乙醇溶液交替旋涂得到Ag-PVA/TiO₂有机/无机复合薄膜.紫外-可见吸收光谱研究表明,随着Ag-PVA层数的增加,薄膜的表面等离子体共振吸收强度呈线性增加,但是TiO₂层数的增加对吸收光谱没有明显影响.Ag-PVA/TiO₂有机/无机复合薄膜将金属纳米粒子、有机高分子与无机半导体材料结合在一起,这种多层纳米结构在光电、催化功能薄膜等方面具有潜在的应用前景.     

不同催化剂作用下聚乳酸/聚碳酸亚丙酯的酯交换反应

选用辛酸亚锡[Sn(Oct)₂]和钛酸四丁酯(TBT)作为聚乳酸(PLA)/聚碳酸亚丙酯(PPC)的酯交换反应催化剂, 研究了溶液条件下单一催化剂及复合催化剂对PLA/PPC酯交换反应的催化作用. 通过对反应产物的分子结构、 热力学及流变学行为进行分析, 结果发现, 无论在单一催化剂还是复合催化剂作用下, PLA与PPC分子间均发生了酯交换反应, 同时伴随着断链反应. 其中, 当Sn(Oct)₂作为单一催化剂或Sn(Oct)₂/TBT作为复合催化剂时, 样品更倾向发生断链反应而非显著的酯交换反应. 进一步分析纯样品在催化剂Sn(Oct)₂或TBT作用下的反应情况, 结果发现, PPC在反应最初阶段以高分子量的分子链断链为主, 且会发生明显的解拉链降解, 从而导致PLA/PPC在等质量比时酯交换反应程度不高, 这为今后更好地研究PLA/PPC酯交换反应提供了思路.     

Electrochemical determination of methimazole based on the acetylene black/chitosan film electrode and its application to rat serum samples

A novel method has been developed for the determination of methimazole, which was based on the enhanced electrochemical response of methimazole at the acetylene black/chitosan composite film modified glassy carbon electrode. The electrochemical behavior of methimazole was studied at this film electrode by cyclic voltammetry and differential pulse voltammetry. The experimental results showed that methimazole exhibited a remarkable oxidation peak at 0.63V at the film electrode. Compared with the bare glassy carbon electrode, the oxidation peak current increased greatly, and the peak potential shifted negatively, which indicated that the acetylene black/chitosan film electrode had good catalysis to the electrochemical oxidation of methimazole. The enhanced oxidation current of methimazole was indebted to the nano-porus structure of the composite film and the enlarged effective electrode area. The influences of some experimental conditions on the oxidation of methimazole were tested and the calibration plot was examined. The results indicated that the differential pulse response of methimazole was linear with its concentration in the range of 1.0×10(-7) to 2.0×10(-5)mol/L with a linear coefficient of 0.998, and in the range of 4.0×10(-5) to 3.0×10(-4)mol/L with a linear coefficient of 0.993. The detection limit was 2.0×10(-8)mol/L (S/N=3). The film electrode was used to detect the content of methimazole in rat serum samples by the standard addition method with satisfactory results.     

DNA／聚（3-甲基噻吩）复合膜修饰电极的制备及其应用于研究8-羟基-2＇-脱氧鸟嘌呤核苷的伏安行为及测定

首先通过电聚合方法在玻碳电极表面制备了聚（3-甲基噻吩）（P3MT）修饰膜,然后在一定电位下将DNA分子电沉积到P3MT表面,制备了DNA／（P3MT）复合膜修饰玻碳电极．研究了8-羟基-2’-脱氧鸟嘌呤核苷（8-OH-dG）在该复合膜修饰电极上的伏安行为以及扫描速度、pH值和尿酸对其伏安行为和检测的影响．实验结果表明,该复合膜修饰电极结合了P3MT和DNA两者的优点,使8-OH-dG在复合膜修饰电极上的电化学行为明显改善,而且具有很好的重现性和稳定性．在0．1mol／LpH7．0的磷酸盐缓冲溶液（PBS）中,8-OH-dG的氧化峰电流与其浓度在0．28～4．2μmol／L和4．2～19．6μmol／L两个范围内成良好的线性关系,检出限为56nmol／L（S／N=3）．该研究可以为制备HPLC或毛细管电泳电化学检测器检测8-OH—dG打下一定的基础,因此在检测尿样中8-OH-dG的研究方面具有潜在的应用价值．     

Formation of a composite based on selenium nanoparticles stabilized with poly-<Emphasis Type="Italic">N,N,N,N</Emphasis>-trimethylmethacryloyloxyethylammonium methyl sulfate and on Acetobacter xylinum cellulose gel films

Formation of a composite based on selenium nanoparticles stabilized with poly-N,N,N,N-trimethylmethacryloyloxyethylammonium methyl sulfate and on Acetobacter xylinum cellulose gel films was studied. Optimal sorption parameters at which the amorphous form of selenium is preserved in the composite film were suggested.