固相浸渍法制备NiO/CeO2催化剂及其在CO氧化反应中的应用

采用固相浸渍法制备了一系列NiO/CeO2催化剂,并通过与常规湿浸渍法比较,考察了制备方法对催化剂和CO氧化反应性能的影响.同时结合X射线衍射(XRD),N2吸附-脱附(BET),透射电镜(TEM),氢气-程序升温还原(H2-TPR),拉曼(Raman)光谱,X射线光电子能谱(XPS)等手段对催化剂的结构和表面物种分散状态进行了表征.CO氧化活性测试结果表明,当镍负载量相同时,固相浸渍法制备的催化剂相比于湿浸渍法表现出更好的催化性能.TEM、XPS、H2-TPR结果表明,固相浸渍法更有利于加强镍铈间的相互作用和得到高分散的镍物种,从而促进镍物种的还原.Raman结果表明固相浸渍法相比于湿浸渍法能产生更多氧空位,这有利于氧气在催化剂表面的活化,使得CO氧化反应更容易进行.     

Highly Active Nickel Nanoparticles Supported on TiO2 Nanotube Electrodes for Methanol Electrooxidation

Nickel nanoparticles/TiO₂ nanotubes/Ti electrodes were prepared by galvanic deposition of nickel nanoparticles on the TiO₂ nanotubes layer on titanium substrates. Titanium oxide nanotubes were fabricated by anodizing titanium foil in a DMSO fluoride‐containing electrolyte. The morphology and surface characteristics of titanium dioxide nanotubes and Ni/TiO₂/Ti electrodes were investigated using scanning electron microscopy and energy‐dispersive X‐ray spectroscopy, respectively. The results indicated that nickel nanoparticles were homogeneously deposited on the surface of TiO₂ nanotubes. The electrocatalytic behaviour of nickel nanoparticles/TiO₂/Ti electrodes for the methanol electrooxidation was studied by electrochemical impedance spectroscopy, cyclic voltammetry, differential pulse voltammetry and chronoamperometry methods. The results showed that Ni/TiO₂/Ti electrodes exhibit a considerably higher electrocatalytic activity toward the oxidation of methanol.     

Study of the nature and properties of surface centers of a Ni-Cr oxide catalyst according to ir spectra of adsorbed CO and NH3 probe molecules

The modification of a Ni-Cr oxide catalyst during reduction was studied by IR spectroscopy of adsorbed CO and NH₃ probe molecules. It was determined that in the starting oxidized sample the nickel cations were in the form of oxide clusters distributed over the surface of chromium oxide. As a result of reduction, they were depleted in oxygen, and metal clusters were formed and enlarged. Effective oxidation, by water vapor, of part of the surface of the metallic-nickel clusters that formed during reduction was observed.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 12, pp. 2718–2725, December, 1991.     

Enhancement of Lewis Acidity of Cr-Doped Nanocrystalline SnO2: Effect on Surface NH3 Oxidation and Sensory Detection Pattern

Understanding ammonia oxidation over metal oxide surfaces is crucial for improving its detection with resistive type gas sensors. Formation of NO_x during this process makes sensor response and calibration unstable. Cr-doping of nanocrystalline metal oxides has been reported to suppress NO₂ sensitivity and improve response towards NH₃, however the exact mechanism of such chromium action remained unknown. Herein, by using EPR spectroscopy we demonstrate formation of Cr(VI) lattice defects on the surface of nanocrystalline Cr-doped SnO₂. Enhancement of Cr-doped SnO₂ surface acidity and ammonia adsorption as a result has been revealed by using in situ IR spectroscopy. Moreover, a decrease in concentration of free electrons in the conduction band has been shown as a result of substitutional Cr(III) defects formation. Weaker NO_x chemisorption during ammonia oxidation over SnO₂ surface after Cr doping has been found with the use of mass-spectrometry assisted NH₃ thermo-programmed desorption. The given example of surface acidity adjustment and electronic configuration by means of doping may find use in the design of new gas-sensing metal oxide materials.     

Catalytic activity of Cu-containing oxide systems with K2CO3 additives in the oxidation of diesel soot by oxygen

It is shown by XRD that mixed oxide phases Cu_0.92Co_2.08O₄ and Cu₄MgO₅ are formed along with the oxides CuO, Co₃O₄, MgO, and CaO under certain conditions. The positive catalytic effect of individual oxides (CuO and Co₃O₄) and mixed oxide systems (CuO-Cu_0.92Co_2.08O₄, CuO-CaO, and Cu-MgO-Cu₄MgO₅) on the oxidation of diesel soot at 280–580°C is established, and a series of catalytic activities CuO-Cu_0.92Co_2.08O₄ > CuO-MgO-Cu₄MgO₅ > CuO-CaO = CuO > Co₃O₄ is revealed. Using TEM, the surface micromorphology of crystallites that form oxide systems is characterized. It is found that a catalytic system’s activity increases as the size and surface smoothness of crystallites diminishes. According to data from X-ray photoelectron spectroscopy, a considerable increase in the concentration of O₂ in soot with CuO and Co₃O₄ additives after its oxidation by oxygen is observed without changing the oxidation state of Cu and Co oxidation. The promoting effect of potassium additives in the form of K₂CO₃ on the investigated catalytic systems during soot oxidation is revealed.     

Reactivity of the Pt/WO3/GC Electrode Towards Ethylene Glycol Oxidation in 0.1 M H2SO4

WO₃ has been prepared via thermal decomposition of ammonium paratungstate. The obtained oxide has been characterized by X‐ray diffraction (XRD) spectroscopy. The particle size was found to increase with increasing calcination temperature. The modified Pt/WO₃/GC electrode has been prepared and characterized using various analytical and electrochemical techniques. The electrochemical oxidation of ethylene glycol (EG) on the modified electrode was investigated and compared with that of a Pt/GC electrode in acidic solution. The presence of WO₃ enhanced the electrode activity towards EG oxidation. The enhancement factor was found to depend on the ratio of WO₃:Pt as well as on the calcination temperature during WO₃ preparation     

Effect of La2O3 on Catalytic Performance of Au/TiO2 for CO Oxidation

Pure TiO₂ and La-doped TiO₂ were prepared by the sol-gel method. Au was supported on TiO₂ by the deposition-precipitation (DP) method, and its catalytic activity for CO oxidation was tested. The results showed that doping La in Au/TiO₂ could improve its catalytic activity obviously for CO oxidation. The analyses of X-ray diffraction (XRD), temperature-programmed desorption (TPD), and Brunauer-Emmett-Teller (BET) surface area further showed that the presence of La in TiO₂ not only increased its surface area and restrained the growth of TiO₂ crystallites, but could also enhance the microstrain of TiO₂. In terms of O₂-TPD, a new adsorbed species O⁻ appeared on the surface of La-doped TiO₂. The results of in-situ Fourier transform-infrared (FT-IR) spectroscopy illustrated that the high activity of Au/La₂O₃-TiO₂ was attributed to the presence of La promoting the reactivity of CO adsorbed on the Au site and the formation of the second active site on the surface of TiO₂     

钙钛矿型氧化物负载纳米金属催化剂结构的动态调变及其催化氧化CO反应性能

研究了钛酸钡和钛酸钙担载的Ag和Pt纳米催化剂的表面结构随氧化-还原处理过程的动态变化及其对CO完全氧化反应性能的影响.发现氧化物担载的Ag催化剂在氧化处理后其催化活性较还原处理的高; X射线衍射(XRD)和X射线光电子能谱(XPS)表征结果表明,氧化处理能够提高载体表面Ag颗粒的分散度,而还原处理导致Ag颗粒的聚集,从而降低了催化氧化CO反应的活性.氧化-还原处理改变了担载Ag纳米粒子的尺寸并影响其CO氧化反应活性.与此相反,氧化物担载的Pt催化剂在还原处理后所表现出的CO氧化反应活性较氧化处理的高; 对比研究发现,氧化和还原处理后Pt纳米粒子的尺寸基本相同,但是氧化处理的样品中Pt表面物种以氧化态为主,而还原处理后Pt表面物种主要为金属态.Pt纳米粒子表面化学状态随氧化-还原处理的调变是导致表面催化活性差异的主要原因.     

A Raman spectroscopy study of cerium oxide in a cerium–5 wt.% lanthanum alloy

This paper describes a study of a cerium–5 wt.% lanthanum (Ce–5 wt.% La) alloy using Raman spectroscopy and X-ray diffraction (XRD). Examination of the alloy microstructure by optical microscopy and Raman spectroscopy revealed the presence of inclusions which were identified as cerium oxide (CeO₂). The study also highlighted the need to avoid excessive laser power during acquisition of the Raman spectra as this appeared to cause the oxidation of the region being analysed where previously no cerium oxide peak had been detected. The propensity of cerium to oxidise in air results in the formation of a CeO₂ layer on the surface of the alloy. Raman spectroscopy of the oxide layer formed on the alloy after exposure to air for 21 days found that the Raman peak denoting cerium oxide was seen at between 5 and 7 cm⁻¹ lower than the value for CeO₂ (465 cm⁻¹). This is attributed to a combination of a sub-stoichiometric oxide layer and the presence of La in the alloy.     

Preparation, characterization and gas-sensitive properties of nano-crystalline Cr2O3Fe2O3 mixed oxides

A series of Fe₂-_xCr_xO₃(x = 0, 0.4, 0.8, 1.2, 1.6, 2.0) mixed oxides have been prepared with the chemical coprecipitation method and characterized by specific surface area, transmission electron microscopy (TEM), powder X-ray diffraction (XRD), IR and Mössbauer spectroscopy. Single-phase Fe-Cr mixed oxide nano-crystalline powders with corundum structure are obtained, and the results of the five characterization methods are well accordant with each other. Furthermore, gas-sensitive properties of the sensors made of the oxide powders have been studied.     

Comparative analysis of the composition, structure, and catalytic activity of the NiO-CuO-TiO2 on Titanium and NiO-CuO-Al2O3 on aluminum composites

The catalytically active oxide structures based on Al and Ti prepared by plasma-electrolytic oxidation (PEO) and additionally modified by impregnation with an aqueous solution of nickel and copper nitrates followed by annealing were studied. The oxide film-metal composites were studied using X-ray diffraction and X-ray spectroscopic analysis, X-ray electron spectroscopy, and electron microscopy. The catalytic activity of the composites in the reaction of CO oxidation was studied. In spite of differences in the elemental composition and morphology, the initial oxide layers on Al and Ti were comparable in terms of activity. Microgranules of size ～ 1 µm and formations from tens to hundreds of nanometers in size were detected on the surface of PEO layers. The modified layers contained crystalline CuO, NiO, and Al₂O₃ or TiO₂ phases. The surface layers of the modified structures about 3 nm in thickness on AMg5 aluminum alloy and VT1-0 titanium had the same elemental composition but exhibited different activity in the reaction of CO oxidation to CO₂.     

Catalytic Etching of Platinoid Gauzes during the Oxidation of Ammonia by Air. Reconstruction of Surface of Platinoid Gauzes at 1133 K in Air,in Ammonia,and in an NH<Subscript>3</Subscript> + O<Subscript>2</Subscript> Reaction Medium

The structure, morphology, and chemical composition of the surface and near-surface layers of platinoid wires of polycrystalline gauzes, containing Pt (81 wt %), Pd (15 wt %), Rh (3.5 wt %), and Ru (0.5 wt %) after treatment at 1133 K in various media—in air, in ammonia, and after NH3 oxidation in air—are studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectroscopy, and X-ray photoelectron spectroscopy (XPS). A thin film is found on the surface of the initial gauze containing an oxide layer of Rh₂O₃ with a thickness of ~2 nm, on the surface of which an inhomogeneous graphite-like layer 10–50 nm thick is located. It is shown that the heat treatment of gauzes in air leads to the partial removal of the surface graphite-like film that forms the reticulated structure on the wire surface. The treatment of gauzes in an ammonia atmosphere leads to the complete removal of the graphite-like and oxide layers and to the growth of metal grains of ~10 μm. After the catalytic reaction of NH3 oxidation, a deep structural rearrangement of the surface layer of the wire takes place, as a result of which crystalline metal agglomerates of ~10 μm are formed. It is supposed that the reaction of NH3 molecules with oxygen atoms penetrated on the defects leads to the local increase of temperature, due to which the metal atoms emerge on the surface and form large crystalline agglomerates and pores in the region of the grain boundaries.     

Investigation of Fe−Ni Mixed‐Oxide Catalysts for the Reduction of NO by CO: Physicochemical Properties and Catalytic Performance

A series of Fe?Ni mixed‐oxide catalysts were synthesized by using the sol–gel method for the reduction of NO by CO. These Fe?Ni mixed‐oxide catalysts exhibited tremendously enhanced catalytic performance compared to monometallic catalysts that were prepared by using the same method. The effects of Fe/Ni molar ratio and calcination temperature on the catalytic activity were examined and the physicochemical properties of the catalysts were characterized by using XRD, Raman spectroscopy, N₂‐adsorption/‐desorption isotherms, temperature‐programmed reduction with hydrogen (H₂‐TPR), temperature‐programmed desorption of nitric oxide (NO‐TPD), and X‐ray photoelectron spectroscopy (XPS). The results indicated that the reduction behavior, surface oxygen species, and surface chemical valence states of iron and nickel in the catalysts were the key factors in the NO elimination. Fe_0.5Ni_0.5O_x that was calcined at 250 °C exhibited excellent catalytic activity of 100 % NO conversion at 130 °C and a lifetime of more than 40 hours. A plausible mechanism for the reduction of NO by CO over the Fe?Ni mixed‐oxide catalysts is proposed, based on XPS and in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) analyses.     

XPS spectroscopic study of potentiostatic and galvanostatic oxidation of Pt electrodes in H2SO4 and HClO4

The surface oxides produced from potentiostatic and galvanostatic oxidation of Pt electrodes in HClO₄ and H₂SO₄ are examined using X-ray photoelectron spectroscopy. The oxide I species produced as the initial oxidation product by successively more anodic potentiostatic oxidation in 0.2 M HClO₄ is found to have a Pt²⁺ oxidation state, a binding energy characteristic of neither PtO, Pt(OH)₂ or PtO₂, and a limiting thickness of 8 Å. Galvanostatic oxidation in HClO₄ and H₂SO₄ is found to produce PtO₂·H₂O as an unlimiting growth oxide or a limiting growth oxide layer depending on the concentration of the acid electrolyte. The incorporation of the acid electrolyte anion in the surface layer is shown to have an effect on which type of oxide layer is produced. X-ray decomposition and chemical modification by Ar⁺ stripping are shown to produce chemical artifacts complicating any interpretation of a Pt oxide surface layer.     

O2和CO在Ni(111)表面的吸附活化

采用高分辨电子能量损失谱(HREELS)、俄歇电子能谱(AES)和低能电子衍射(LEED)研究镍单晶表面氧物种及CO与O₂的共吸附。实验结果表明,Ni(111)表面氧化后存在两种氧物种,位于54 meV能量损失峰的表面化学吸附氧物种和位于69 meV能量损失峰的表面氧化镍。首先,随着暴露氧量的增加,表面化学吸附氧物种的能量损失峰蓝移至58 meV;其次,通过真空退火及与CO相互作用考察,发现表面化学吸附氧物种较不稳定。在室温条件下,表面预吸附形成的表面化学吸附氧物种与CO共吸附,导致端位吸附CO增多,表明氧优先吸附在穴位上,随着CO暴露量的增加化学吸附氧物种与CO反应脱去;而表面氧化镍需在较高温度和较高CO分压下才能被CO还原。预吸附CO可被氧逐渐移去。     

Preparation,properties, and catalytic activity of platinum-modified plasma electrolytic oxide structures on aluminum

Catalytically active Pt-containing oxide composites on aluminum have been prepared by plasma electrolytic oxidation (PEO) and by additional modification of the resulting coating by impregnation with an aqueous solution of chloroplatinic acid followed by calcination. The oxide film/metal composites have been characterized by X-ray diffraction, X-ray photoelectron spectroscopy, and electron microscopy. The modified films contain the γ-Al₂O₃ and Pt crystalline phases. Platinum in the surface and subsurface layers is in the Pt⁰ state. There are platinum-rich areas on the surface of the PEO films. A higher catalytic activity in CO oxidation into CO₂ is shown by the samples whose oxide film contains nickel and copper along with platinum.     

Synthesis, crystal structure and thermal decomposition of a new copper propionate [Cu(CH3CH2COO)2]·2H2O

A new copper propionate complex was synthesised and characterized for application as precursor for CuO based oxide thin films deposition. The FT-IR and X-ray diffraction analyses have revealed the formation of a cooper propionate complex [Cu(CH₃CH₂COO)₂]·2H₂O. The crystal and molecular structure of a new copper propionate complex was determined by XRD on the copper propionate single crystal. The copper propionate complex has a binuclear structure, connected by bridging bidentate carboxylates groups and a Cu?Cu bond of 2.6 Å. The thermal decomposition of copper propionate has been investigated by thermal analysis using thermogravimetric (TG) and differential thermal analysis (DTA), differential thermal analysis coupled with quadrupole mass spectrometry-QMS, X-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FT-IR) techniques. TG and XRD data indicate the reduction of Cu(II)-Cu(I,0) during the decomposition of copper propionate.     

Oscillatory electrocatalytic oxidation of methanol on an Ni(OH)2 film electrode

A film of Ni(OH)₂ deposited cathodically on a roughened nickel substrate consists of even nanoparticles, which were characterized by atomic-force microscopy (AFM). The mechanism of potential oscillations in the electrocatalytic oxidation of methanol on this film electrode in alkaline medium was studied in situ by means of Raman spectroscopy in combination with electrochemical measurements. The redox change of the nickel hydroxide film, the concentration distribution of methanol in the diffusion layer, and the oxidation products of methanol were characterized in situ by time-resolved, spatial-resolved, and potential-dependent Raman spectroscopy, respectively. Electrochemical reactions, i.e. methanol oxidation and periodic oxygen evolution, coupling with alternately predominant diffusion and convection mass transfer of methanol, account for the potential oscillations that occur during oxidation of methanol above its limiting diffusion current. This mechanism is totally different from that of methanol oxidation on platinum electrodes, for which surface steps, i.e. formation and removal of CO_ad, are essential.This work is dedicated to Professor Gyorgy Horanyi on the occasion of his 70th birthday in recognition of his numerous contributions to field of electrochemical oscillations and electrocatalysis at Ni-hydroxide electrodes.     

CO oxidation on Ta-Modified SnO2 solid solution catalysts

Co-precipitation method was adopted to prepare Sn–Ta mixed oxide catalysts with different Sn/Ta molar ratios and used for CO oxidation. The catalysts were investigated by N₂-Brunauer–Emmett–Teller (N₂-BET), X-ray diffraction patterns (XRD), H₂-temperature programmed reduction (H₂-TPR), Thermal Gravity Analysis – Differential Scanning Calorimetry (TGA–DSC) techniques. It is revealed that a small amount of Ta cations can be doped into SnO₂ lattice to form solid solution by co-precipitation method, which resulted in samples having higher surface areas, improved thermal stability and more deficient oxygen species on the surface of SnO₂. As a result, those Sn rich Sn–Ta solid solution catalysts with an Sn/Ta molar ratio higher than 4/2 showed significantly enhanced activity as well as good resistance to water deactivation. It is noted here that if tantala disperses onto SnO₂ surface instead of doping into its lattice, it will then have negative effect on its activity.     

TG measurement of reactivity of candidate oxygen carrier materials

This study examined several candidate raw materials for use as the reactive agents in developing new oxygen carriers for chemical looping combustion. A thermogravimetric analyzer, Mettler TGA/DSC1, was used to measure oxygen capacity and relative reaction rates during oxidation and reduction cycles. The reactive gases used were 4 % hydrogen in inert gas for the reduction cycle and air for the oxidation cycle, with a nitrogen purge between reduction and oxidation cycles. Samples were typically tested for at least ten cycles to study any change in reactivity or oxygen capacity. Reaction temperatures tested ranged from 700 to 900 °C. Materials tested included an iron oxide ore, iron-based tailings from a metals extraction process, a nickel oxide supported on nickel aluminate and a copper oxide plus inert material system. The materials varied in their oxygen capacity, reactivity and the change in properties with repeat cycles. Of the samples tested, the NiO–NiAl₂O₄ oxygen carrier demonstrated the fastest reaction in reduction and oxidation and had stable properties over ten cycles. The iron oxide ore sample performance declined significantly with repeat cycles. The performance of the iron-based tailings declined slightly over the ten cycles. The addition of inert second phase materials to CuO improved the performance by inhibiting sintering of the oxide at the operating temperature. Although the reactivity of the tailings and iron hydroxide samples was not as high as the NiO based oxygen carrier, they are promising carrier materials due to their low cost and lower toxicity relative to nickel. Future experiments will look at CO and CH₄ reduction reactions using the TG, surface characterization using SEM, XRD, and cyclic testing in a batch fluidized bed reactor.