三通管路的管壁声传递损失测试方法

针对汽车进气系统三通管路的特点,提出了多通管路的管壁传递损失测试方法。并以某车型的双涡轮增压发动机进气三通管道为例,采用该方法评价其用塑料代替铝后的声学性能,主要以声传递损失来评价涡轮增压器噪声通过三通连接管路管壁的辐射和透射特性。测试过程中,三通管道的两个连接涡轮增压器端口分别用声源两次发声,靠近进气歧管端口采用两种不同反射末端,然后在每段管路布置两个压力场扬声器进行测试,并基于平面波分离入射波和反射波,同时在三通管道外用声功率半球面十点分布法自由场扬声器测试,经过3次测量来计算管道管壁的声传递损失。由于声传递损失是管道本身特性决定,所以该测试方法能够准确找出塑料件和金属件在不同频率的声学特性差异。而后,在声传递损失测试结果的基础上,结合近场声全息方法和波束形成原理进行声源识别,可知该三通管路材质改为塑料后主要噪声来自焊缝薄弱处的中高频透射声和管壁结构的低频辐射声。     

T型三通水管路噪声特性数值研究

水管路系统工作运行中会产生较大的管路振动和流噪声.作为偶极子声源,充液管路内湍流激发的脉动压力会形成流噪声,且激励管壁产生流激振动噪声.为了揭示水管道系统的流激振动噪声与流噪声特性的区别,基于有限元方法对不同厚度的充液管路声学模态、结构模态以及耦合模态进行计算;基于计算流体力学联合声学边界元的混合计算方法探讨变流速下流...     

电动声源热声致冷机声学和计算实例

我们将各种热声致机简化为一包括声学终端在内的声管道系统，并通过实例讨论了致冷机的声学特性，该管道系统与一般声管道不同：１．在热声堆中热波和粘滞波不可不计。２．在热声堆与声管连接时，必需考虑合成波的体积流；而热声堆内只需考虑传播波的体积流。本文对此提出了阻抗连接条件的修正。实例使用电动扬声器为声源，给出了热声行波和驻波致冷的声学计算方法以及它们的声学特性，所用扬声器的标称伏安为１００ＶＡ，可为热声致     

参量阵扬声器在管道噪声控制中的研究*

为了解决管道有源噪声控制中声反馈造成的系统复杂度和计算量的增加,文中引入参量阵扬声器作为次级声源,利用其强指向性减小控制系统的声反馈。为了验证该方法可行性,本文分别在直管和L管中,对600 Hz单频噪声和频率范围为500 Hz~1000 Hz的窄带噪声进行了管道有源噪声控制,同时测量了参量阵扬声器的管内声场和降噪范围。结果表明,参量阵扬声器声反馈小,在没有声反馈补偿的条件下对单频噪声的降噪效果基本达到了声反馈补偿条件下普通扬声器的降噪效果,对窄带噪声的降噪效果稍差。此外,通过测量管道声场和降噪量,确定了参量阵扬声器的降噪区域为误差传感器下游整个管道,降噪面积为管道整个截面。这说明参量阵扬声器作为次级声源降低了系统的复杂度和算法的计算量,并取得了较好的降噪效果。     

面向目标的定向声辐射技术及其应用研究

面向目标的定向声辐射是指利用声源特性和阵列信号处理技术,将声波传送至目标方向或区域的声场控制方法。本文介绍了定向声辐射技术的原理和进展,重点阐述了普通扬声器阵列和参量阵扬声器这两种声源形式的理论、算法和应用研究。其中,针对扬声器阵列,主要分析了基于声能量对比度控制的声聚焦技术;针对参量阵扬声器,综述了利用非线性效应产生高指向性可听声的计算方法、信号预处理和应用等进展。面向目标的定向声辐射技术的研究对实现智能声场控制有着重要意义。     

旋转声源辐射噪声的矢量声学研究方法

通过采用频域方法直接求解旋转声源辐射噪声的声压和声粒子速度矢量,建立了旋转声源辐射噪声的矢量声学研究方法。该方法的最大优势在于提供了一种直观、形象的方法显示声能量的传播途径。基于该方法分别分析了旋转声源在自由空间和边界散射情形下的声能量传播特征。     

没有声反射的房间──消声室

 在房间里,人说话、音响设备通过扬声器（喇叭）发出声音或者机器发出噪声,另一个人耳朵听到的声音,不仅有直达声,还有墙面、地面、天花板的一次和多次反射声,同时还有室外传来的干扰声．ＡＢ两人,在办公室内、在空旷安静的大操场上和在山洞里保持相同距离,Ａ发出相同的声音,而Ｂ听到的声音却明显不同．因为在这三种情况下,反射声的强弱明显不同．对声源进行精确测量时,必须没有反射声和室外干扰声．例如：１．电声厂生产的各种规格的扬声器,必须测量其频率响应、指向性等声学特性,看其是否达到设计要求．２．音响的整机声学特性的测量．３．机器（如冰箱、空调器、机床、汽车等）的噪声特性测量．４．语音的声调、频谱研究.     

基于声辐射模态讨论声能量辐射与传递

声辐射模态表示了振动声源表面的辐射模式。基于声辐射模态讨论了振动声源表面声能量辐射和声场中声能量传递的性质,给出声能量辐射和传递的模式。采用表面声强描述振动声源表面的声能量辐射,采用声强描述声能量在声场中的传递。表面声强和声强可分解成两部分,一部分将辐射的声能量传递到远场;另一部分表现为振动声源与声场之间的能量交换。针对矩形板分析了声能量辐射和传递,数值计算结果与理论结果一致。结果表明基于声辐射模态讨论声能量辐射与传递是可行的和有效的。     

点噪声源在近程声场中传播损失的仿真研究

在分层介质条件下，用本征声线法仿真计算了点声源这距离噪声场的传播损失曲线，仿真结果表明，其传播损失不仅依赖于声速分布，海区深度，海底反射特性等环境条件，也依赖于声源及接收水听器的深度，声传播损失显著不同于球面波衰减规律，其传播损失率差别可达８ｄＢ，这表明在测量舰船目标的辐射噪声声源级时必要的声场校正测量是必须的。     

矢量气动声学的理论研究进展及应用

气动声学的声比拟理论以密度、声压等标量为波动算子变量,建立非齐次波动方程,描述流体运动及与边界作用诱发声音的辐射,但标量无法直接描述声能量的传播过程和途径.在流体力学研究中,标量用于描述当前当地的物质状态,而矢量用于描述质量和能量的传输.借鉴上述思想,开展了矢量气动声学的研究,概述矢量气动声学的理论研究进展及应用,主要包括:（1）以声粒子速度为变量,采用声比拟理论的思想直接从Navier-Stokes方程出发推导建立了气动声学的矢量波动方程及两种频域解;（2）综合利用声压和声粒子速度的积分解,直接求解声源周围的瞬时和有功声强矢量场,直观显示声能量的传播途径,应用于旋转声源辐射声能量的传播分析,揭示了亚音速旋转声源辐射声能量的3种传播模式:螺旋模式、声学黑洞模式和R-A模式;（3）采用球谐级数展开方法建立旋转点/紧凑声源辐射噪声的声压和声粒子速度的频域解析解,在此基础上推导了声功率谱的频域解析解,建立了识别旋转叶片声源在空间域和频域分布特征的方法;（4）综合利用矢量气动声学方法和等效源方法,显示声源和散射边界周围声强矢量场的分布特征和能量传播途径,直接揭示了阻抗边界主要的吸声位置以及直接计算得到阻抗边界的吸收声功率.      

Low frequency acoustic transmission through the walls of rectangular ducts

A simple theory is described for the transmission of low frequency sound through the walls of rectangular ducts, particularly those in air conditioning systems. The model is based on a coupled acoustic/structural wave system, and it is assumed that the duct radiates in the same way as a finite-length line source incorporating a single travelling wave. Measurements of wall transmission loss on two types of duct system are compared to theoretical predictions, and good agreement is obtained within the frequency range of validity of the theory. It is concluded that the present approach should give reliable estimates of noise transmission in practical situations.     

Feedback control of sound transmission through a double glazed window

One way to tackle the control of stochastic noise in three dimensions is to reduce the sound transmission to the zone of interest. In buildings, windows are often the weak link in protecting the interior from outside noise. In particular, double glazed windows have a poor sound insulation at low frequency around the mass-air-mass resonance (double wall resonance). Since passive means for windows are exhausted, an active controller that increases the transmission loss in the low-frequency range is an attractive approach to reduce the noise level in buildings. Previously suggested feedforward controllers need reference microphones to measure the disturbance outside and error microphones for the adaptation somewhere in the room. For a real window this is unpractical or even unfeasible. These limitations can be overcome with the feedback controller presented here, which only uses sensors and actuators in the cavity of the double glazed window. Four different controllers—two feedforward and two feedback strategies—are designed, implemented and compared. With feedback the noise transmission around the mass-air-mass resonance can be reduced by , compared to with a feedforward controller.     

Sound attenuation of a periodic array of micro-perforated tube mufflers

The wave propagation in a periodic array of micro-perforated tube mufflers is investigated theoretically, numerically and experimentally. Because of the high acoustic resistance and low mass reactance due to the sub-millimeter perforation, the micro-perforated muffler can provide considerable sound attenuation of duct noise. Multiple mufflers are often used to enhance attenuation performance. When mufflers are distributed periodically in a duct, the periodic structure produces special dispersion characteristics in the overall sound transmission loss. The Bloch wave theory and the transfer matrix method are used to study the wave propagation in periodic micro-perforated tube mufflers and the dispersion characteristics of periodic micro-perforated mufflers are examined. The results predicted by the theory are compared with finite element method simulation and experimental results. The results indicate that the periodic structure can influence the performance of micro-perforated mufflers. With different periodic distances, the combination of the periodic structure and the micro-perforated tube muffler can contribute to the control of lower frequency noise with a broader frequency range or improvement of the peak transmission loss around the resonant frequency.     

Prediction of intake noise of an automotive engine in run-up condition

It is very important to predict the radiated noise from the engine intake system for the effective noise control and virtual prototyping of in-cavity and outdoor noise of a vehicle. To this end, one should precisely measure the in-duct acoustic source parameters of the intake system, viz., source strength and source impedance. Usually, the noise radiation characteristics need to be expressed as a function of engine speed. In this study, acoustic source parameters of an engine intake system under engine run-up condition were measured by using the direct method. Direct method employed two external loudspeakers, turned on simultaneously, and three microphones for the separation of upstream and downstream wave components. It was noted that the frequency spectra of source impedance hardly changes with the increase of engine speed. Utilizing this fact, source strength under the engine run-up condition was calculated by assuming invariant source impedance. Predicted insertion loss and radiated sound pressure level using the measured source parameters were compared with those of measured data and predicted data using several idealized source models, which have been adopted for the calculations. A reasonably good agreement was observed between measured sound spectra at the intake orifice and predicted one using the measured source data. It was shown that the source data obtained by the present method yielded a far better prediction accuracy than those by the idealized source models.     

Sound power flux measurements in strongly exited ducts with flow

This contribution describes new robust procedures for the measurement of sound power flux at appropriate axial positions along a duct with flow, using pairs of flush wall mounted microphones, or pressure transducers. The technology includes the application of selective averaging, order tracking, and optimized sampling rate methods to identify the small fraction of the total fluctuating wave energy that is being propagated along the flow path in a reverberent, or highly reactive duct system. Such measurements can also be used to quantify the local acoustic characteristics that govern the generation, transfer, and propagation of wave energy in the system. Illustrative examples include the determination of the acoustic characteristics of individual silencing elements installed in IC engine intakes and exhausts both on the flow bench and during controlled acceleration or run down on a test bed, where the wave component spectral levels approached 170 dB.     

Application of cylindrical near-field acoustical holography to the visualization of aeroacoustic sources

The purpose of this study was to develop methods for visualizing the sound radiation from aeroacoustic sources in order to identify their source strength distribution, radiation patterns, and to quantify the performance of noise control solutions. Here, cylindrical Near-field Acoustical Holography was used for that purpose. In a practical holographic measurement of sources comprising either partially correlated or uncorrelated subsources, it is necessary to use a number of reference microphones so that the sound field on the hologram surface can be decomposed into mutually incoherent partial fields before holographic projection. In this article, procedures are described for determining the number of reference microphones required when visualizing partially correlated aeroacoustic sources; performing source nonstationarity compensation; and applying regularization. The procedures have been demonstrated by application to a ducted fan. Holographic tests were performed to visualize the sound radiation from that source in its original form. The system was then altered to investigate the effect of two modifications on the fan's sound radiation pattern: first, leaks were created in the fan and duct assembly, and second, sound absorbing material was used to line the downstream duct section. Results in all three cases are shown at the blade passing frequency and for a broadband noise component. In the absence of leakage, both components were found to exhibit a dipole-like radiation pattern. Leakage was found to have a strong influence on the directivity of the blade passing tone. The increase of the flow resistance caused by adding the acoustical lining resulted in a nearly symmetric reduction of sound radiation.     

切向流对微穿孔共振吸声结构声学性能的影响

切向流对微穿孔共振吸声结构声学性能的影响可以分成三类:(1)对小孔辐射声抗的影响;(2)对结构斜入射吸声性能的影响;(3)对消声通道消声性能的影响。根据声学基本理论,详细讨论这些影响,得到对应的理论分析公式。定性而言,若声波的传播方向与气流的运动方向一致,小孔外侧的辐射声抗、空腔声阻抗函数coth (ξ)的宗量ξ赋值和消声通道的消声系数都会减小;同时呈现多普勒效应,使得结构的吸声系数共振峰频率向低频移动。理论分析得到相应实验研究的支持。      

Investigation into higher-order mode propagation through orifice plates in circular ducts

Most established techniques for analyzing sound transmission in ducts containing orifices plates are only applicable for plane wave propagation. Once the wavelength of the sound approaches the cross section of the duct, higher order mode propagation in the system must be considered in the analysis. This is a numerically intensive activity if fully coupled calculations of the higher order modes are undertaken. This investigation estimates the acoustic fields in a duct with a simple orifice plate installed using an uncoupled model to estimate the higher order mode contribution. The uncoupled model is then used as the basis for a hybrid decomposition approach to estimate the sound field in the regions before and after the orifice plate installed in a circular duct. This approach is applied to a duct, excited by a point source over a wide frequency range, containing a single orifice plate installed a distance inside the duct. Different orifice plates with one, two and multiple openings are investigated. Of particular interest is the location of the point source relative to the duct axis. If the source is located concentric to the duct axis then, without any orifice plate present, only axially symmetric higher order modes may be excited in the duct. Thus, the investigation considers the point source located in the concentric position and in eccentric positions to vary the contribution from the different types of higher order mode. Estimates of the acoustic fields in the duct obtained using the hybrid decomposition approach are compared with measured data and the applicability of using an uncoupled estimate for the acoustic fields is commented on.     

The effect of grazing mean flow on acoustical characteristics of the micro-perforated panel absorber

There are three effects of grazing mean flow on acoustical characteristics of the micro-perforated panel absorber(1) on radiation impedance of the orifice,(2) on acoustical impedance of the construction at sound wave angle incidence,(3) on sound propagation property in a duct lined by absorber.Based on the acoustical fundamental principle,these effects were analyzed respectively,and relative formulas were derived. Some qualitative tendencies were shown that radiation impedance of an orifice,value ofξin function coth(ξ) which estimates cavity impedance,and transmission loss in a lined duct all will decrease with flow speed increases as well as the resonant frequency will move to lower frequency caused by Doppler Effect,when sound wave propagation direction is the same with flow direction. The discussion was also supported by a relative experimental study.