聚(4-乙酰基丙烯酰乙酸乙酯-co-丙烯酸)水凝胶的溶胀动力学以及温度敏感性研究

通过分子结构设计, 合成了疏水性单体4-乙酰基丙烯酰乙酸乙酯(AAEA), 并以该单体与丙烯酸(AA)进行自由基溶液共聚, 制备了P(AAEA-co-AA)新型温度敏感性水凝胶. AAEA的¹H NMR及FT-IR分析表明, 该单体主要以烯醇式结构存在; P(AAEA-co-AA)的FT-IR分析发现, PAAEA与PAA之间存在较强烈的氢键作用, 使得AAEA烯醇异构体中的C—O伸缩振动吸收峰移向了低波数处. 对冷冻干燥后凝胶的电镜分析发现, 当AAEA用量较高时, 由于凝胶内部分子链段的疏水聚集, 各部分溶胀度以及溶胀速度不均一而使得凝胶表面粗糙不平. 采用DSC对凝胶的体积相转变进行了研究, 结果表明, 该水凝胶的体积相转变温度(VPTT)在48.2至61.8 ℃之间, 并且随着AAEA用量的减小, 凝胶的VPTT逐渐增加. 对该新型温度敏感性水凝胶在去离子水中的溶胀动力学研究发现, 当AAEA用量高于4.6 g时, 凝胶属于Fick凝胶; 反之凝胶则属于非Fick凝胶. 该水凝胶在去离子水中具有良好的温度敏感性, 当外界温度低于VPTT时, 凝胶能保持溶胀状态; 而当外界温度高于VPTT时, 凝胶的平衡溶胀度迅速下降, 表现为温度敏感性. 进一步研究发现, 凝胶组成不仅会影响凝胶的VPTT, 而且会影响凝胶温度敏感性的强弱.     

PVA-PAMPS-PAA三元互穿网络型水凝胶的合成及其性能研究

以2-丙烯酰胺基-2-甲基丙磺酸(AMPS)、丙烯酸(AA)以及聚乙烯醇(PVA)为原料,制备了PVA-PAMPS-PAA三元互穿网络型(T-IPN)水凝胶.红外分析表明,PVA与PAA以及PAMPS之间形成了较强的氢键,使得PVA分子上的C—O伸缩震动吸收峰移向了低波数处.X射线衍射以及电镜分析表明,当PVA用量较低时,PVA能均匀的穿插于凝胶网络中,形成完善的互穿网络结构,当PVA用量过高时,部分的PVA结晶而使得凝胶出现相分离.研究了该三元互穿网络型水凝胶的溶胀性能,结果表明,该水凝胶的平衡溶胀比在200至340之间,并且随着AA以及AMPS用量的增加,凝胶的溶胀速率以及平衡溶胀比均升高.该三元互穿网络型水凝胶在酸性溶液中和在碱性溶液中表现出截然不同的消溶胀性能;并且随着溶液pH的升高,凝胶在pH=9.0附近出现体积突变,表现出pH敏感性.通过研究T-IPN水凝胶的抗压缩性能发现,利用线型高分子、柔性高分子网络以及刚性高分子网络制备的三元互穿网络型水凝胶能在高溶胀比下保持较高的强度.溶胀比为180的T-IPN水凝胶,其最大抗压缩强度可达12.1 MPa.进一步研究发现,凝胶的组成以及溶胀比均对凝胶的抗压缩强度和压缩应变均存在较大的影响.     

大孔PAMPS/PVA半互穿网络型水凝胶的制备及其性能研究

以PEG6000为成孔剂, 合成了大孔聚(2-丙烯酰胺-2-甲基丙磺酸)/聚乙烯醇半互穿网络型(s-IPN)水凝胶. 红外分析表明, PVA与PAMPS之间形成了较强的氢键, 使得PVA分子上的C—O伸缩振动吸收峰移向了低波数处. X射线衍射分析发现, 当PVA用量较高时, 由于部分的PVA结晶, 使得凝胶的半互穿网络结构不均匀. 电镜分析结果表明, 没有使用成孔剂的凝胶表面成褶皱形, 不存在任何孔洞结构; 而以PEG6000为成孔剂的凝胶表面存在相互贯穿的大孔结构. 研究了该水凝胶的溶胀性能, 结果表明, 该水凝胶的平衡溶胀度在116至320之间; 而成孔剂PEG6000的加入能较大幅度提高凝胶的溶胀速率, 凝胶在240 min之内就能达到溶胀平衡. 对凝胶抗压缩性能的研究表明, 当PVA用量为9.1% (w)时, 凝胶的抗压缩强度最大, 可达12.0 MPa; 而成孔剂的加入会在一定程度削弱凝胶的抗压缩强度. 该凝胶具有较好的电场敏感性, 研究发现, 将吸去离子水达到溶胀平衡的凝胶放入施加有电场的0.2 mol•L－1 NaCl溶液中时, 凝胶迅速偏向阳极. 而PVA和成孔剂PGE6000的用量均对凝胶的偏转速度以及最大偏转角存在较大的影响.     

P(AA-co-DMDAAC)/PVA凝胶的制备和吸金性能研究

以丙烯酸(AA)、二甲基二烯丙基氯化铵(DMDAAC)为单体,聚乙烯醇(PVA)为第二网络,通过水溶液聚合法制备P(AA-co-DMDAAC)/PVA半互穿水凝胶(SIPNH)。采用FT-IR、XRD、SEM等对凝胶的结构进行了表征。结果表明,PVA用量为5%时,PVA与P(AA-co-DMDAAC)能形成较完善的半互穿网络结构。探讨了凝胶的抗压缩性能、溶胀/消溶胀性能。结果表明,SIPNH形成的半互穿网络结构可以改善凝胶的抗压缩强度,最大抗压缩强度达到0.37MPa。凝胶的溶胀/消溶胀速率随PVA用量的增加呈下降趋势。着重研究了PVA及氯金酸(HAuCl4)用量对SIPNH吸金能力的影响。结果表明,PVA用量大于5%时,SIPNH的吸金能力明显降低。当HAuCl4浓度为250mg/L时,最大吸附量为108.5mg/g。     

聚丙烯酰胺/聚异丙基丙烯酰胺互穿网络水凝胶的制备与性能

采用分步法用电子加速器辐射合成了聚丙烯酰胺(PAAm)/聚异丙基丙烯酰胺(PNIPAAm)互穿网络水凝胶,并考察了温度、pH值、离子强度对其溶胀性能的影响.研究表明:互穿水凝胶具有温度敏感性,且其体积相变与互穿网络中PAAm和PNIPAAm含量有关,随着网络中PAAm含量的增加水凝胶的体积相变趋于平缓,可以通过改变PAAm和PNIPAAm的组成比来控制水凝胶的体积相变行为.此外,互穿水凝胶还具有pH敏感性和一定的抗盐性.     

羧甲基壳聚糖/海藻酸钠半互穿网络水凝胶的制备及性能研究

以羧甲基壳聚糖(CMC)和海藻酸钠(SA)为原料,京尼平(GP)为交联剂,制备具有pH敏感性的CMC/SA半互穿网络(semi-IPN)水凝胶.利用特性黏数、红外光谱对CMC/SA水凝胶的半互穿网络结构及形成机理进行了分析与表征;对水凝胶的力学性能进行了测试;探讨了pH值及交联剂含量对水凝胶溶胀性能的影响.结果表明,京尼平交联的CMC/SA水凝胶具有半互穿网络结构.当w(CMC)∶w(SA)=5∶5时,CMC/SA水凝胶的断裂强度达到最大值(59 MPa),分别比纯的CMC(40 MPa)和SA(36 MPa)提高了47.5%和63.9%;当SA含量为60%时,CMC/SA水凝胶的断裂伸长率达到最大值(13.0%).当pH3.0时,溶胀率随pH值的增大而减小,pH=3.0时,溶胀率最小(186%);当pH3.0时,溶胀率随pH值的增大而增大,pH=9.0时,溶胀率最大(886%).京尼平交联的CMC/SA半互穿网络水凝胶具有明显的pH敏感性、溶胀可逆性及对pH的快速响应性.     

丝胶基半互穿温敏凝胶的合成及其溶胀行为的研究

采用半互穿网络技术, 将具有生物相容性的丝胶蛋白(silk sericin)作为第二网络进入聚(N-异丙基丙烯酰胺)(PNIPAM)水凝胶网络中, 在水溶液中制备得到具有半互穿网络结构的丝胶基温敏水凝胶(SS/PNIPAM semi-IPNs). 采用称重法研究了产物的(消)溶胀、温度敏感性、最大溶胀度及脉冲响应行为; 利用扫描电镜(SEM), 差示扫描量热仪(DSC)和动态热机械分析仪(DMA)分别考察了产物的内部形态、热相转变行为和其储能模量随温度的变化. 结果表明: 具有较高亲水性的丝胶蛋白的引入增大了semi-IPNs水凝胶的内部孔径, 导致SS/PNIPAM半互穿水凝胶的溶胀度增加, 并且其储能模量随温度变化更明显. 相比于纯PNIPAM水凝胶, 半互穿水凝胶的消溶胀速率和低临界溶解温度(LCST)变化不大.     

聚乙烯醇/羧甲基壳聚糖共混水凝胶的辐射合成及性能

采用电子加速器辐照法制备了聚乙烯醇(PVA)/羧甲基壳聚糖(CMCH)共混水凝胶;研究了PVA与CMCH的配比、辐照剂量、温度以及pH值对PVA/CMCH共混水凝胶性能的影响.实验发现,PVA与CMCH在辐照剂量为40 kGy、配比为w(PVA)/w(CMCH)=5/1的条件下可得到强度较好的PVA/CMCH共混水凝胶,该水凝胶具有一定的温度和pH敏感性:在5~20℃时具有较高的溶胀率,温度在20℃以上溶胀率较低;水凝胶在pH<4.0和pH>6.0时溶胀率均较大,而当pH为4.0~6.0时溶胀率较小.     

磁性半互穿网络智能水凝胶的合成及性质评价

以甲基丙烯酸(MAA)、N-异丙基丙烯酰胺(NIPAAm)、丙烯酰胺(AM)为原料,N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,利用IPN技术并结合磁性的γ-Fe2O3增强剂,在水溶液中制备了半互穿网络水凝胶(PMAA/PAM-NIPAAm/γ-Fe2O3),研究了水凝胶的溶胀性﹑热稳定性和电磁性。实验表明,水凝胶形成稳定的IPN互穿网络结构且该水凝胶具温度、pH双重敏感性和顺电磁性。所合成的水凝胶在低临界溶解温度31℃以下,具有明显正向温敏性,高于此温度,水凝胶的温度敏感性会逐渐减弱。产品成功克服了NIPAAm类水凝胶的温缩性。     

温度和pH敏感P(NIPA-co-AA)/粘土复合水凝胶的辐射制备与表征

以N-异丙基丙烯酰胺(NIPA)作为温敏性聚合单体,丙烯酸(AA)为pH敏感性单体,有机粘土为改性剂,采用~(60)Co-γ射线为辐射源,辐射合成了P(NIPA-co-AA),粘土复合水凝胶,研究了粘土的加入对水凝胶溶胀率、温度及pH敏感性和压缩性能的影响.结果表明,P(NIPA-co-AA)/粘土复合水凝胶的溶胀性能优于P(NIPA-co-AA)水凝胶,平衡溶胀率(SR)明显提高;且复合水凝胶仍表现出明显的温度和pH敏感性;粘土的加入提高了水凝胶的压缩强度、最大压缩力和压缩屈服力等力学性能,当粘土含量为15%时,P(NIPA-co-AA)/粘土复合水凝胶的压缩强度为P(NIPA-co-AA)共聚水凝胶的2.4倍,最大压缩力为P(NIPA-co-AA)的2.1倍.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.