Development of a headspace-solid phase micro extraction method to monitor changes in volatile profile of rose (Rosa hybrida, cv David Austin) petals during processing

In the present study, headspace solid phase microextraction combined to capillary gas chromatography (HS-SPME-GC) has been applied for the determination of changes in the volatile profile of rose petals (Rosa hybrida, cvs David Austin) following processing (heat treatment and addition as an ingredient to a food product--for example yoghurt). Four SPME fibres at two sampling temperatures (40 and 60 degrees C) with a sampling time of 30 min were examined. Volatile profiles were detected either by FID or/and by olfactometry (ODP-II, Gerstel). Fibre testing was performed using raw rose petals for sampling temperature selection and an 18 characteristic rose volatile standard mixture in water was used to compare fibre performances at the sampling temperature of 60 degrees C. Polydimethylsiloxane-divinylbenzene (PDMS-DVB) fibre at the sampling temperature of 60 degrees C was the most suitable to sample the rose alcohols phenyl ethanol, citronellol, nerol, geraniol and eugenol, as assessed by GC-olfactometry, not only from raw petals, but also from processed rose petals and the food product. PDMS-DVB fibre also showed a desired low affinity to volatiles from yoghurt, which reduces the influence of food matrix on the volatile profile. The method was linear over two orders of magnitude and had satisfactory repeatability, with limits of detection for the rose alcohols ranging from <1 to 10 ng/ml concentration levels.     

山楂挥发性化合物的气相色谱-质谱分析

采用蒸馏－萃取法收集山楂果的挥发性化合物,通过气相色谱及气相色谱／质谱分析,鉴定了３２种化合物,占总峰面积的６１％～６８％。其中主要的１０种化合物是顺－３－己烯醇、顺－３－乙酸己烯酯、α－萜品醇、糠醛、己醇、乙酸己酯、壬醛、柠檬醛、３－戊烯－２－酮,反－２－癸烯醛等。     

气相色谱-质谱法分析橡苔浸膏中的挥发性化学成分

 用挥发油提取器提取橡苔浸膏中的挥发油,利用气相色谱-质谱法(GC-MS)分析了其中的化学成分,采用GC峰面积归一化法定量,鉴定出24种化合物,共占挥发油总量的83%以上     

The role of biodegradation during bioventing of soil contaminated with jet fuel

The enhancing rem oval of kerosene (jet fuel) from contaminated soil during bioventing resulting from biodegradation was compared to the physical removal by evaporation only on bench-scale columns at the controlled temperature of 20°C (±2.5°C). Carbon dioxide-free air and nitrogen were used as flushing gases, at the constant continuous flow rate of 1 dm³/h. Kerosene concentrations in soil up to 35000 mg/kg were not toxic for indigenous microbial population. Much slower kerosene biodegradation rates observed for soil from a contaminated site, as compared to soil artificialy contaminated with kerosene, were the result of a lower bioavailability of “aged” kerosene, and the presence of compounds that might be persistent or toxic to kerosene-specific degraders. The inhibitory effect of toluene to indigenous microorganisms was found at above 75% of the toluene saturation concentrations in the gas phase. After 29 d, the overall bioventing efficiency was 17–23%, depending on whether CO₂ production or O₂ uptake wasused for caculations, as compared to the removal of 10% when biodegradation was excluded. The increase in efficiency by 50–100% owing to biodegradation would be more spectacular at lowr kerosene concentrations during the “tailing” phase, with diffusionlimited desorption, and much lower evaporation of less volatile constituents. Limitation of bioventing as a result of low bioavailability related to intraparticle sorption of residual contamination is discussed.     

Analysis of volatile contaminants in vegetable oils by headspace solid-phase microextraction with carboxen-based fibres

The headspace solid-phase microextraction (HS-SPME) efficiencies from vegetable oil of the recently available Carboxen-poly(dimethylsiloxane) (PDMS) and divinylbenzene-Carboxen-PDMS fibres were found to be much greater than those of the PDMS fibre for a number of volatile contaminants. Using these Carboxen-based fibres, the commonly used HS-SPME equilibration times for aqueous matrices of 30-45 min at room temperature for a number of halogenated and aromatic analytes with volatilities ranging from 1,1-dichloroethylene to hexachlorobenzene were found to be insufficient for the effective extraction of the less volatile analytes from vegetable oil. HS-SPME at 100 degrees C for 45 min, followed by rapid cooling to 0 degrees C with a 10 min continuing extraction, however, significantly increased the SPME efficiencies for the less volatile analytes. Spiking solutions were prepared in vegetable oil instead of methanol as the latter was found to displace analytes from the Carboxen material. Using either of the Carboxen-based fibres and SPME at 100 degrees C, all the target analytes could be determined at low or sub-microg kg(-1) with repeatability < or =10%, even though an equilibrium SPME of the less volatile analytes was not achieved.     

Systematic study of beta-asarone-rich volatile oil from Acori graminei rhizoma by off-line supercritical CO2 extraction-gas chromatography-mass spectrometry

Supercritical CO2 extraction (SCE) technology was used to extract a volatile oil, rich in beta-asarone, from Acori graminei rhizoma (AGR). The effect of different extraction and fractionation parameters on oil yield and selectivity towards beta-asarone was investigated by SCE using commercial AGR samples. The optimal conditions (P(e)/T(e) = 10 MPa/45 degrees C; P(f1)/T(f1) = 8 MPa/-10 degrees C; P(f2)/T(f2 )= 2 MPa/10 degrees C) gave a good oil yield and selectivity for beta-asarone. The extracts were also analyzed by GC-MS and compared with the volatile oil obtained by hydrodistillation, in which 39 main constituents including beta-asarone were found. Different cultivated AGR samples obtained from three areas of China were evaluated in terms of their volatile oil compositions obtained by extraction of commercial AGR samples under optimal conditions; the extract of the Guangdong (GD) sample showed a high beta-asarone content.     

气相色谱-质谱法测定大蒜挥发油的组成

采用改进的水蒸汽蒸馏法从山东金乡大蒜中提取挥发油。实验确定了气相色谱-质谱法分析大蒜油的条件,并对大蒜挥发油的化学成分进行了定性分析,共鉴定出20种物质。用峰面积归一化法对各物质的相对含量进行了测定,结果表明含硫化合物约占挥发油总成分的95%以上,其中含量最高的是大蒜新素,约占挥发油总量的三分之一。对低温储藏半年的挥发油进行分析的结果表明样品在低温下可稳定存放。     

Comparative analysis of the oil and supercritical CO(2) extract of Artemisia arborescens L. and Helichrysum splendidum (Thunb.) Less

Isolation of volatile concentrate from the dried leaves of Artemisia arborescens and of Helichrysum splendidum has been obtained by supercritical extraction with carbon dioxide. To obtain a pure volatile extract devoid of cuticular waxes, the extraction products were fractionated in two separators operating in series. A good extraction process was obtained operating at 90 bar and 50 degrees C in the extraction vessel, at 90 bar and at -5 degrees C in the first separator and at a pressure between 20 and 15 bar and temperatures in the range 10-20 degrees C in the second one. The composition of the volatile concentrate has been analyzed by GC/MS. The volatile concentrate of A. arborescens was found to contain: trans-thujone (13.96%), camphor (6.15%) and chamazulene (5.95%).The main constituents in the extract of H. splendidum were: germacrene D-4-ol (17.08%), germacrene D (9.04%), bicyclogermacrene (8.79%) and delta-cadinene (8.43%). A comparison with the oils obtained by hydrodistillation is also given.The differences observed between the composition of the SFE volatile concentrates and of the hydrodistilled (HD) oils were relevant. Indeed, the HD oils had a blue color whereas the volatile concentrates were pale yellow. The HD oil of H. splendidum had a blue color due to the presence of guaiazulene (0.42% vs 0%), whereas the coloration of HD oil of A. arborecens was due to the high concentration of chamazulene (26.64% vs 3.37%).     

树兰花挥发性成分的提取及鉴定

采用超临界CO2流体从树兰花中提取挥发油,得油率为2.64%。利用气相色谱-质谱联用仪(GC-MS)对树兰花油中的化学成分进行分离和鉴定,共分离出54种组分,确认了其中的48种成分,其中有18种萜烯类化合物和12种酯类物质等成分,如α-蛇麻烯、亚麻酸乙酯、大根香叶烯-D、β-榄香烯、古巴烯、石竹烯、茉莉酮酸甲酯、β-蛇麻烯-7-醇和棕榈酸乙酯等。     

Controlled nucleation and growth of CdS nanoparticles in a polymer matrix

In-situ synchrotron X-ray diffraction (XRD) was used to monitor the thermal decomposition (thermolysis) of Cd thiolates precursors embedded in a polymer matrix and the nucleation of CdS nanoparticles. A thiolate precursor/polymer solid foil was heated to 300 degrees C in the X-ray diffraction setup of beamline W1.1 at Hasylab, and the diffraction curves were each recorded at 10 degrees C. At temperatures above 240 degrees C, the precursor decomposition is complete and CdS nanoparticles grow within the polymer matrix forming a nanocomposite with interesting optical properties. The nanoparticle structural properties (size and crystal structure) depend on the annealing temperature. Transmission electron microscopy (TEM) and photoluminescence (PL) analyses were used to characterize the nanoparticles. A possible mechanism driving the structural transformation of the precursor is inferred from the diffraction features arising at the different temperatures.     

A DNA sieving matrix with thermally tunable mesh size

We present a "proof-of-concept" study showing that a blend of thermo-responsive and nonthermo-responsive polymers can be used to create a DNA sieving matrix with a thermally tunable mesh size, or "dynamic porosity". Various blends of two well-studied sieving polymers for CE, including hydroxypropylcellulose (HPC), a thermo-responsive polymer, and hydroxyethylcellulose (HEC), a nonthermo-responsive polymer, were used to separate a double-stranded DNA restriction digest (Phi X174-HaeIII). HPC exhibits a volume-phase transition in aqueous solution which results in a collapse in polymer coil volume at approximately 39 degrees C. Utilizing a blend of HPC and HEC in a ratio of 1:5 by weight, we investigated the effects of changing mesh size on DNA separation, as controlled by temperature. High-resolution DNA separations were obtained with the blended matrix at temperatures ranging from 25 degrees C to 38 degrees C. We evaluated changes in the selectivity of DNA separation with increasing temperature for certain pairs of small and large fragments. A pure HEC (nonthermo-responsive) matrix was used over the same temperature range as a negative control. In the blended matrix, we observe a maximum in selectivity at approximately 31 degrees C for small DNA, while a significant increase in the selectivity of large-DNA separation occurs at approximately 36 degrees C as the polymer mesh "opens". We also demonstrate, through a temperature ramping experiment, that this matrix can be utilized to obtain high-resolution separation of both small and large DNA fragments simultaneously in a single CE run. Blended polymer matrices with "dynamic porosity" have the potential to provide enhanced genomic analysis by capillary array or microchip electrophoresis in microfluidic devices with advanced temperature control.     

固相微萃取-气相色谱/质谱测定植物叶片中的挥发性物质

采用固相微萃取（SPME)方法吸附植物叶片中的挥发性物质,然后采用气相色谱/质谱法（GC/MS）分析了挥发性物 质的成分。在45 ℃水浴温度下,采用Polyacrylate(85 μm)固相微萃取头,在广口瓶中植物叶片的上方顶空吸附60 min,然后进行GC/MS分析。结果表明,植物叶片中的挥发性物质得到了很好的分离,受山楂叶螨(Tetraychus vienneis) 危害严重的植物的完好叶片中的挥发性物质均含有顺-3-己烯-1-醇乙酸酯、顺-3-己烯-1-醇丁酸酯和α-法呢烯,且含量 较大。初步确定这些物质是对山楂叶螨具有引诱作用的主要物质,从而为利用天然生物活性物质防治山楂叶螨提供了理论 依据。     

顶空固相微萃取气相-质谱法测定纺织品中防虫蛀剂的残留

 采用顶空固相微萃取技术和气相 质谱联用技术对纺织品中的挥发性防虫蛀剂的残留进行了测定。该方法对挥发性二氯苯和萘的检测限量为 1μg/kg ,回收率为 83 6 %～ 115 2 % ,相对标准偏差为 8 1%～ 9 8%。     

Rapid headspace solid-phase microextraction-gas chromatographic-time-of-flight mass spectrometric method for qualitative profiling of ice wine volatile fraction. I. Method development and optimization

An analytical method for the determination of volatile and semi-volatile compounds representing various chemical groups in ice wines was developed and optimized in the presented study. A combination of the fully automated solid-phase microextraction (SPME) sample preparation technique and gas chromatographic-mass spectrometric (GC-MS) system to perform the final chromatographic separation and identification of the analytes of interest was utilized. A time-of-flight mass spectrometric (TOF-MS) analyzer provided very rapid analysis of this relatively complex matrix. Full spectral information in the range of m/z 35-450 was collected across the short GC run (less than 5 min). Divinylbenzene/Carboxen/Polydimethylsiloxane (DVB/CAR/PDMS) 50/30 microm fiber performed best during the optimization experiments and it was used in the headspace SPME mode to isolate compounds from ice wine samples, consisting of 3 mL wine with 1g salt addition. After the sample incubation and extraction (both 5 min at 45 degrees C), analytes were thermally desorbed in the GC injector for 2 min (injector maintained at 260 degrees C) and transferred into the column. The MS data acquisition rate of 50 spectra/s was selected as optimal. The optimized analytical method did not exceed 20 min per sample, including both the isolation and pre-concentration of the analytes of interest, the final GC-TOF-MS analysis and the fiber bake-out. Both a linear temperature-programmed retention index (LTPRI) method using C(8)-C(20) alkanes loaded onto the fiber and a mass spectral library search were employed to identify the target compounds. The repeatability of the developed and optimized HS-SPME-GC-TOF-MS method for ice wine analysis, expressed as relative standard deviation (RSD, %, n=7), ranged from 3.2 to 9.0%.     

Headspace solid phase microextraction (HSSPME) for the determination of volatile and semivolatile pollutants in soils

We have investigated the use of headspace solid phase microextraction (HSSPME) as a sample concentration and preparation technique for the analysis of volatile and semivolatile pollutants in soil samples. Soil samples were suspended in solvent and the SPME fibre suspended in the headspace above the slurry. Finally, the fibre was desorbed in the Gas Chromatograph (GC) injection port and the analysis of the samples was carried out. Since the transfer of contaminants from the soil to the SPME fibre involves four separate phases (soil-solvent-headspace and fibre coating), parameters affecting the distribution of the analytes were investigated. Using a well-aged artificially spiked garden soil, different solvents (both organic and aqueous) were used to enhance the release of the contaminants from the solid matrix to the headspace. It was found that simple addition of water is adequate for the purpose of analysing the target volatile organic chemicals (VOCs) in soil. The addition of 1 ml of water to 1 g of soil yielded maximum response. Without water addition, the target VOCs were almost not released from the matrix and a poor response was observed. The effect of headspace volume on response as well as the addition of salt were also investigated. Comparison studies between conventional static headspace (HS) at high temperature (95 degrees C) and the new technology HSSPME at room temperature ( approximately 20 degrees C) were performed. The results obtained with both techniques were in good agreement. HSSPME precision and linearity were found to be better than automated headspace method and HSSPME also produced a significant enhancement in response. The detection and quantification limits for the target VOCs in soils were in the sub-ng g(-1) level. Finally, we tried to extend the applicability of the method to the analysis of semivolatiles. For these studies, two natural soils contaminated with diesel fuel and wood preservative, as well as a standard urban dust contaminated with polyaromatic hydrocarbons (PAHs) were tested. Discrimination in the response for the heaviest compounds studied was clearly observed, due to the poor partition in the headspace and to the slow kinetics of all the processes involved in HSSPME.     

Evaluation of matrix effects in the analysis of volatile organic compounds in whole blood with solid‐phase microextraction

The complexity and matrix variability of biological samples requires an accurate evaluation of matrix effects. The dilution of the biological sample is the simplest way to reduce or avoid the matrix effect. In the present study, a set of volatile organic compounds with different volatilities was used to assess the effect of the dilution of blood samples on the extraction efficiency by headspace solid‐phase microextraction. It was found that there was a significant matrix effect but that this effect differs significantly depending on the volatility of the compound. A 1:2 (blood/water) dilution was enough to allow quantitative recoveries of those compounds with boiling points <100°C. For compounds with boiling points between 100 and 150°C, the matrix effect was stronger and a 1:5 dilution was required. The dilution of blood samples proved to be inefficient for quantitative recovery of compounds with boiling points >150°C. A 1:5 dilution of the sample allowed detection limits in the range of nanogram per liter to be obtained. This was sufficient to detect the main volatile compounds present in blood and contamination after exposure.     

Quantification of volatile sulfur compounds in complex gaseous matrices by solid-phase microextraction

Procedures were assessed for quantifying nine volatile sulfur compounds found in complex gaseous samples collected at a biogas-production plant and a sewage treatment plant. The target compounds were extracted by solid-phase microextraction (using the 75-microm Carboxen-polydimethylsiloxane fiber coating) at 22 degrees C for 20 min, and analyzed by GC-MS. Detection limits ranged between 1 pptv (v/v) for carbon disulfide and 470 pptv (v/v) for hydrogen sulfide. High amounts of organic compounds were found during full-scan analysis of the samples and standard additions to individual sub-samples revealed that the analysis was subject to matrix effects. However, the functions obtained by standard additions were still linear and quantification was possible for all the compounds tested except hydrogen sulfide. No detectable losses were observed during storage in the sampling containers, made of Tedlar film, over a storage period of 20 h. However, water permeated through the walls and the relative humidity in the bag increased during storage until it reached the ambient level. Finally, it was shown that the drying agent, CaCl2, caused no detectable losses of any of the compounds.     

Determination of volatile residual solvents in traditional Chinese medicines by headspace solid-phase microextraction and cryogenic gas chromatography with flame ionization detection

A method based on headspace solid-phase microextraction and cryogenic gas chromatography with flame ionization detection was developed for the determination of volatile residual solvents in traditional Chinese medicines. A laboratory-made cryogenic chromatographic system was used for the separation of 15 kinds of residual solvents. During the analysis, a 65 microm PDMS/DVB fiber was used to extract the residual solvents, the extraction time was controlled at 0 degrees C for 15 min, and the NaCl content of the sample was maintained at 30%. The limits of detection ranged from 0.08 (for octane) to 5000 microg/L (for ethanol), and the relative standard deviations were < 8%. The recoveries from spiked samples ranged from 88 to 112%. Trace levels of residual solvents in several traditional Chinese medicines were effectively identified and quantified.     

Optimum heat treatment conditions for masking the bitterness of the clarithromycin wax matrix

The effects of the contents of aminoalkyl methacrylate copolymer E (AMCE) in a wax matrix on the mechanism of polymorphic transformation of glyceryl monostearate (GM) were clarified by evaluating the enthalpy change defined as 1.51 (DeltaH(1)-DeltaH(2))/DeltaH(2), where DeltaH(1) and DeltaH(2) denote the enthalpies in the first and second thermal analyses, respectively. Using this value, K(1), the rate constant of transformation from alpha-form to beta'-form, and K(2), the rate constant of transformation from beta'-form to beta-form, could be obtained. As the ratio of AMCE increased, K(2) increased, but a minimum point existed for K(1). K(1) was always larger than K(2), but gradually approached K(2) as the ratio of AMCE increased. The optimum temperature for the transformation of GM was 50 degrees C, at which the enthalpy change was maximum. To prepare the wax matrix preparation of clarithromycin (CAM), we considered 40 degrees C the optimum treatment temperature for the transformation of GM in a CAM wax matrix compounded from CAM, GM and AMCE, since the matrices were mutually welded at above 45 degrees C during the spray congealing process. Although K(1) and K(2) were almost the same at 40 degrees C, the rate of transformation was accelerated by tumbling. By applying the tumbling that accelerated the transformation of GM in a CAM wax matrix, almost all of the alpha-form disappeared, and the release of CAM from the wax matrix diminished when the enthalpy change was more than 0.8.     

Thermoresponsive N,N-dialkylacrylamide copolymer blends as DNA sieving matrices with a thermally tunable mesh size

In an earlier study we showed that a blend of thermoresponsive and nonthermoresponsive hydroxyalkylcelluloses could be used to create a thermally tunable polymer network for double-stranded (ds) DNA separation. Here, we show the generality of this approach using a family of polymers suited to a wider range of DNA separations: a blended mixture of N,N-dialkylacrylamide copolymers with different thermoresponsive behaviors. A mixture of 47% w/w N,N-diethylacrylamide (DEA)/53% w/w N,N-dimethylacrylamide (DMA) (DEA47; thermoresponsive, transition temperature = 55 degrees C in water) and 30% w/w DEA/70% w/w DMA (DEA30; nonthermoresponsive, transition temperature > 85 degrees C in water) copolymers in the ratio of 1:5 w/w DEA47:DEA30 was used to separate a dsDNA restriction digest (PhiX174-HaeIII). We investigated the effects of changing mesh size on dsDNA separation, as controlled by temperature. We observed good DNA separation performance with the copolymer blend at temperatures ranging from 25 degrees C to 48 degrees C. The separation selectivity was evaluated quantitatively for certain DNA fragment pairs as a function of temperature. The results were compared with those obtained with a control matrix consisting only of the nonthermoresponsive DEA30. Different DNA fragment pairs of various sizes show distinct temperature-dependent selectivities. Over the same temperature range, no significant temperature dependence of selectivity is observed for these DNA fragment pairs in the nonthermoresponsive control matrix. Overall, the results show similar trends in the temperature dependency of separation selectivity to what was previously observed in hydroxyalkylcellulose blends, for the same DNA fragment pairs. Finally, we showed that a ramped temperature scheme enables improved separation in the blended copolymer matrix for both small and large DNA fragments, simultaneously in a single capillary electrophoresis (CE) run.