C60 ion sputtering of layered organic materials

Two different organic materials, Irganox1010 and Irganox3114, were vacuum deposited as alternating layers. The layers of Irganox3114 were thin (∼2.5 nm) in comparison to the Irganox1010 (∼55 or ∼90 nm); we call these ‘organic delta layers’. Both materials are shown to have identical sputtering yields and the alternating layers may be used to determine some of the important metrological parameters for cluster ion beam depth profiling of organic materials. The sputtering yield for C₆₀ ions is shown to diminish with ion dose. Comparison with atomic force microscopy data from films of pure Irganox1010, demonstrates that the depth resolution is limited by the development of topography. Secondary ion intensities are a well-behaved function of sputtering yield and may be employed to obtain useful analytical information. Organic delta layers are shown to be valuable reference materials for comparing the capabilities of different cluster ion sources and experimental arrangements for the depth profiling of organic materials.     

溅射粒子能量对金属Mo薄膜表面特性的影响

利用原子力显微镜研究了不同溅射离子能量对Mo薄膜表面形貌的影响.利用特殊设计的夹具，在同一真空内完成所有薄膜样品的制备，减少了多次沉积过程对薄膜生长特性的影响 .对原子力显微镜测量得到的表面高度数据进行相关运算，从统计角度定量地研究了不同沉积能量下Mo薄膜表面特性.结果表明，薄膜表面具有典型的分形特征，在相关运算的基础上给出表面的分形维数、水平相关长度、界面宽度等参数.其中，屏栅电压为500V时制备 的薄膜样品与300和700?V时制备的薄膜样品表面的界面宽度及水平相关长度具有倍数差别，但三种溅射电压下薄 关键词： 离子束溅射 钼 薄膜 分形     

Synthesis of molybdenum silicide by both ion implantation and ion beam assisted deposition

Two groups of Mo/Si films were deposited on surface of Si(1 0 0) crystal. The first group of the samples was prepared by both ion beam assisted deposition (IBAD) and metal vapor vacuum arc (MEVVA) ion implantation technologies under temperatures from 200 to 400 °C. The deposited species of IBAD were Mo and Si, and different sputtering Ar ion densities were selected. The mixed Mo/Si films were implanted by Mo ion with energy of 94 keV, and fluence of Mo ion was 5 × 10¹⁶ ions/cm². The second group of the samples was prepared only by IBAD under the same test temperature range. The Mo/Si samples were analyzed by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), sheet resistance, nanohardness, and modulus of the Mo/Si films were also measured. For the Mo/Si films implanted with Mo ion, XRD results indicate that phase of the Mo/Si films prepared at 400 and 300 °C was pure MoSi₂. Sheet resistance of the Mo/Si films implanted with Mo ion was less than that of the Mo/Si films prepared without ion implantation. Nanohardness and modulus of the Mo/Si films were obviously affected by test parameters.     

Effect of implantation regimes of silver ions on the structure and optical properties of zinc-oxide nanocrystalline films

Thin (about 270 nm) nanocrystalline films of zinc oxide (ZnO) are obtained on quartz substrates using ion sputtering and irradiated with Ag⁺ ions at an energy of 30 keV and relatively high fluences at ion current densities of 4, 8, and 12 µA/cm². The X-ray analysis, scanning electron microscopy, and optical spectroscopy are used to study the effect of irradiation dose and ion current density on the structural modification and optical properties of the ZnO films. Nontrivial dependences of the structural and optical parameters of the films on the ion irradiation regimes are due to radiation heating and film sputtering under the action of the ion beam, diffusion of impurity, formation of silver nanoparticles in the irradiated layer at high implantation fluences, and the diffusion of implanted impurity at relatively high ion current densities.     

Crystal orientation control of polycrystalline TiN thin films using ZnO under layers deposited by magnetron sputtering

The effect of ZnO under layers on crystal growth of TiN thin films was investigated. TiN single layers and double-layered ZnO/TiN thin films were deposited on soda-lime-silicate glass substrates by magnetron sputtering. XRD analysis indicated that TiN single layers exhibited {1 1 1} preferred orientation on glass substrates; on the other hand, the TiN thin films with {1 0 0} preferred orientation were obtained using ZnO under layers and crystallized better than the TiN single layers. This crystal orientation change of TiN thin films should come from heteroepitaxial-like growth because the TiN{1 0 0} and ZnO{0 0 1} crystal lattice planes have similar atomic arrangements. Besides, the possible mismatch between TiN and ZnO atomic arrangements was estimated to be 7.8%. Furthermore, the resistivity and optical absorbance of TiN thin films decreased when they were deposited on ZnO under layers. It can be considered that electrical and optical properties should be improved due to the well-crystallization of TiN thin films using ZnO under layers.     

电子束蒸发和离子束溅射HfO_2紫外光学薄膜

HfO2薄膜在紫外光学中具有十分重要的地位,不同方法制备的HfO2薄膜特性不同,可以满足不同的实际应用需求。本文分别利用电子束蒸发和离子束溅射方法制备了用于紫外光区域的HfO2薄膜,并对薄膜的材料和光学特性进行了表征与比较。通过对单层HfO2薄膜的实测透射和反射光谱进行数值反演,得到了HfO2薄膜在230～800 nm波段的折射率和消光系数色散曲线,结果表明两种方法制备的HfO2薄膜在250nm的消光系数均小于2×10-3。在此基础上,制备了两种典型的紫外光学薄膜元件(紫外低通滤波器和240nm高反射镜),其光谱性能测试结果表明,两种不同方法制备的器件均具有较好的光学特性。     

Comparison of ZnO thin films grown on a polycrystalline 3C-SiC buffer layer by RF magnetron sputtering and a sol-gel method

Zinc oxide (ZnO) thin films were deposited on a polycrystalline (poly) 3C-SiC buffer layer using RF magnetron sputtering and a sol-gel method. The post-deposition annealing was performed on ZnO thin films prepared using both methods. The formation of ZnO piezoelectric thin films with less residual stress was due to a close lattice mismatch of the ZnO and SiC layers as obtained by the sputtering method. Nanocrystalline, porous ZnO film prepared using the sol-gel method showed strong ultraviolet UV emission at a wavelength of 380 nm. The 3C-SiC buffer layer improved the optical and piezoelectric properties of the ZnO film produced by the two deposition methods. Moreover, the different structures of the ZnO films on the 3C-SiC intermediate layer caused by the different deposition techniques were also considered and discussed.     

The effect of C60 cluster ion beam bombardment in sputter depth profiling of organic-inorganic hybrid multiple thin films

The effects of C₆₀ cluster ion beam bombardment in sputter depth profiling of inorganic-organic hybrid multiple nm thin films were studied. The dependence of SIMS depth profiles on sputter ion species such as 500 eV Cs⁺, 10 keV C₆₀⁺, 20 keV C₆₀²⁺ and 30 keV C₆₀³⁺ was investigated to study the effect of cluster ion bombardment on depth resolution, sputtering yield, damage accumulation, and sampling depth.     

Study on the orientation of silver films by ion-beam assisted deposition

Low energy ion beam assisted deposition (IBAD) was employed to prepare Ag films on Mo/Si (100) substrate. It was found that Ag films deposited by sputtering method without ion beam bombardment were preferred (111) orientation. When the depositing film was simultaneously bombardment by Ar⁺ beam perpendicular to the film surface at ion/atom arrival ratio of 0.18, the prepared films exhibited weak (111) and (200) mixed orientations. When the direction of Ar⁺ beam was off-normal direction of the film surface, Ag films showed highly preferred (111) orientation. Monte Carlo method was used to calculate the sputtering yields of Ar⁺ ions at various incident and azimuth angles. The effects of channeling and surface free energy on the crystallographic orientation of Ag films were discussed.     

SIMS study of annealing effect on element distribution in free-standing Al/Si and Zr/ZrSi<Subscript>2</Subscript> multilayer films

The results of secondary ion mass spectrometry (SIMS) depth profile analysis of free-standing Al/Si and Zr/ZrSi₂ multilayer films by a TOF.SIMS-5 instrument are reported for the first time. A prestudy of elemental composition in Zr and ZrSi₂ single layers and Zr/ZrSi₂ multilayer films deposited on Si substrates with sublayers revealed enhanced diffusion of carbon in Zr layers. Ion sputtering and charge neutralization conditions were determined to provide fixed position of free-standing thin films during analysis. An elemental composition of 100-nm-thick Zr/ZrSi₂ multilayer structures with Mo and B₄C protective layers was measured prior and after laser annealing.     

Effects of the sputtering time of ZnO buffer layer on the quality of GaN thin films

ZnO thin films with different thickness (the sputtering time of ZnO buffer layers was 10 min, 15 min, 20 min, and 25 min, respectively) were first prepared on Si substrates using radio frequency magnetron sputtering system and then the samples were annealed at 900 °C in oxygen ambient. Subsequently, a GaN epilayer about 500 nm thick was deposited on ZnO buffer layer. The GaN/ZnO films were annealed in NH₃ ambient at 950 °C. X-ray diffraction (XRD), atom force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and photoluminescence (PL) were used to analyze the structure, morphology, composition and optical properties of GaN films. The results show that their properties are investigated particularly as a function of the sputtering time of ZnO layers. For the better growth of GaN films, the optimal sputtering time is 15 min.     

离子束增强沉积制备p型氧化锌薄膜及其机理研究

采用离子束增强沉积方法在Si和SiO₂/Si衬底上制备In-N共掺杂ZnO薄膜(INZO)，溅射靶是用ZnO和2 atm% In₂O₃粉体均匀混合并压制而成，在氩离子溅射ZnO靶的同时，氮、氩混合离子束垂直注入沉积的薄膜.实验结果显示INZO薄膜具有(002)的择优取向，并且为p型导电，电阻率最低为0.9Ωcm.薄膜在氮气、氧气气氛下退火，对薄膜的结构和电学特性与成膜和退火条件的关系进行了分析. 关键词： 氧化锌薄膜 p型掺杂 离子束增强沉积     

Characteristics of ZnO:In thin films prepared by RF magnetron sputtering

In-doped ZnO (ZnO:In) transparent conductive thin films were deposited on glass substrates by RF magnetron sputtering. The effect of substrate temperature on the structural, electrical and optical properties of the ZnO:In thin films was investigated. It was found that higher temperature improves the crystallinity of the films and promotes In substitution easily. ZnO:In thin films with the best crystal quality were fabricated at 300 °C, which exhibit a larger grain size of 29 nm and small tensile strain of 0.9%. The transmittance of all the films was revealed to be over 85% in the visible range independence of the substrate temperatures and the lowest resistivity of ZnO:In thin films is 2.4×10⁻³ Ω cm.     

Characteristics of ZnO:In thin films prepared by RF magnetron sputtering

In-doped ZnO (ZnO:In) transparent conductive thin films were deposited on glass substrates by RF magnetron sputtering. The effect of substrate temperature on the structural, electrical and optical properties of the ZnO:In thin films was investigated. It was found that higher temperature improves the crystallinity of the films and promotes In substitution easily. ZnO:In thin films with the best crystal quality were fabricated at 300 °C, which exhibit a larger grain size of 29 nm and small tensile strain of 0.9%. The transmittance of all the films was revealed to be over 85% in the visible range independence of the substrate temperatures and the lowest resistivity of ZnO:In thin films is 2.4×10⁻³ Ω cm.     

Nitrogen-doped ZnO prepared by capillaritron reactive ion beam sputtering deposition

Nitrogen-doped ZnO thin films have been prepared by reactive ion beam sputtering deposition utilizing a capillaritron ion source. X-ray diffraction (XRD) analysis of the as-deposited film exhibits a single strong ZnO (002) diffraction peak centred at 34.40°. Post-growth annealing causes increase of grain size and decrease of c-axis lattice constant. Micro-Raman spectroscopy analysis of the as-deposited film shows strong nitrogen-related local vibration mode at 275, 582, 640 and 720 cm⁻¹, whereas the E₂ mode of ZnO at 436 cm⁻¹ can barely be identified. Annealing at 500-800 °C causes decrease of 275, 582, 640 and 720 cm⁻¹ and increase of 436 cm⁻¹ intensity, indicating out-diffusion of nitrogen and improvement of ZnO crystalline quality. Unlike un-doped ZnO, the surface roughness of nitrogen-doped ZnO deteriorates after annealing, which is also attributed to the out-diffusion of nitrogen. A nitrogen concentration of ∼10²¹/cm³ was observed while type conversion from n-type to p-type was not achieved, which is likely due to the formation of Zn_I-N_O or (N₂)_O that act as donor/double donors.     

XPS depth profiling studies of L-CVD SnO2 thin films

In this paper we present the results of the XPS atomic depth profile analysis, using ion beam sputtering, of L-CVD SnO₂ thin films grown on an atomically clean SiO₂ substrate after annealing at 400 °C in dry atmospheric air. From the evolution of the Sn 3d_5/2, O 1s, Si 2p and C 1s core level peaks our experiments allowed the determination of the in depth atomic concentration of the main components of the SnO₂/SiO₂ interface. Thin (few nm) nearly stoichiometric SnO₂ films are present at the topmost layer of the thin films, and progressive intermixing with SnO and silicon oxide is observed at deeper layer. The interface between the Sn and the Si oxide layers (i.e. the effective Sn oxide thickness) is measured at 13 nm.     

Optical and electrical properties of nanocrystal zinc oxide films prepared by dc magnetron sputtering at different sputtering pressures

The nanocrystal thin films of zinc oxide doped by Al (ZnO:Al) were deposited by dc reactive magnetron sputtering on the glass substrates, in the pressure range of 33-51 Pa. From the X-ray diffraction patterns, the nanocrystalline structure of ZnO:Al films and the grain size were determined. The optical transmission spectra depend from the sputtering pressure, but their average value was 90% in the range from 33 Pa to 47 Pa. Also, the sputtering pressure changes the optical band gap of ZnO:Al films, which is highest for films deposited at 37 Pa, 40 Pa and 47 Pa. The obtained films at room temperature have a sheet resistance of 190 Ω/cm² which increases with time, but the films annealed at temperature of 400 °C have constant resistance. The surface morphology of the films was studied by Scanning electron microscopy. XPS spectra showed that the peak of O1s of the as-deposited films is smaller than the peak of the annealed ZnO:Al films.     

Surface morphology of ZnO buffer layer and its effects on the growth of GaN films on Si substrates by magnetron sputtering

ZnO thin films were first prepared on Si(111) substrates using a radio frequency magnetron sputtering system. Then the as-grown ZnO films were annealed in oxygen ambient at temperatures of 700, 800, 900, and 1000°C , respectively. The morphologies of ZnO films were studied by an atom force microscope (AFM). Subsequently, GaN epilayers about 500 nm thick were deposited on the ZnO buffer layers. The GaN/ZnO films were annealed in NH₃ ambient at 900°C. The microstructure, morphology and optical properties of GaN films were studied by x-ray diffraction (XRD), AFM, scanning electron microscopy (SEM) and photoluminescence (PL). The results are shown, their properties having been investigated particularly as a function of the ZnO layers. For better growth of the GaN films, the optimal annealing temperature of the ZnO buffer layers was 900°C.     

Boron doped ZnO thin films fabricated by RF-magnetron sputtering

By using the radio frequency-magnetron sputtering (RF-MS) method, both pure ZnO and boron doped ZnO (ZnO:B) thin films were deposited on glass substrates at ambient temperature and then annealed at 450 °C for 2 h in air. It is found that both ZnO and ZnO:B thin films have wurtzite structure of ZnO with (0 0 2) preferred orientation and high average optical transmission (≥80%). Compared with the resistivity of 6.3 × 10² Ω cm for ZnO film, both as-deposited and annealed ZnO:B films exhibit much lower resistivity of 9.2 × 10⁻³ Ω cm and 7.5 × 10⁻³ Ω cm, respectively, due to increase in the carrier concentration. Furthermore, the optical band gaps of 3.38 eV and 3.42 eV for as-deposited and annealed ZnO:B films are broader than that of 3.35 eV for ZnO film. The first-principles calculations show that in ZnO:B thin films not only the band gap becomes narrower but also the Fermi level shifts up into the conduction band with respect to the pure ZnO film. These are consistent with their lower resistivities and suggest that in the process of annealing some substituted B in the lattice change into interstitial B because of its smaller ion radius and this transformation widens the optical band gap of ZnO:B thin film.     

Grain size of nanocrystalline YSZ buffer layers fabricated by ion beam deposition

Amorphous or nanocrystalline thin films are capable to be efficient diffusion barrier layers for YBCO coated conductors of ion beam assisted deposition route. Nanocrystalline Yttria-Stabilized Zirconia (YSZ) buffer layers were fabricated by the ion beam deposition. Kr and Ar gases were utilized for the dual Kaufman type sputtering ion sources sequently. Both of the ion beams were fixed at 200 mA, while the ion energy was in the range of 450–2000 eV. The thickness of the YSZ buffer layers was several hundreds of nanometers. The grain size of YSZ thin films, which varied from 2 to 20 nm, was calculated by Scherrer Formulation based on the X-ray diffraction measurement results. The grain size always decreased at first and then increased when the ion energy was increased. In the cases Kr gas was utilized and Ar gas was utilized, the grain size reached its minimum value at the ion energy of about 1800 eV and 1000 eV, respectively. Such phenomenon was discussed using the thermodynamic theory of thin film nucleation. Deposition rate and substrate temperature were the two chief variables of the critical nuclei concentration and grain size.