Etching graphitic carbon nitride by acid for enhanced photocatalytic activity toward degradation of 4-nitrophenol

Graphitic carbon nitride （g-C3N4） with high photocatalytic activity toward degradation of 4-nitrophenol under visible light irradiation was prepared by HCI etching followed by ammonia neutralization. The structure, morphology, surface area, and photocatalytic properties of the prepared samples were studied. After treatment, the size of the g-C3N4 decreased from several micrometers to several hundred nanometers, and the specific area of the g-C3N4 increased from 11.5 m2/g to 115 m2/g. Meanwhile, the photocatalytic activity of g-C3N4 was significantly improved after treatment toward degradation of 4- nitrophenol under visible light irradiation. The degradation rate constant of the small particle g-C3N4 is 5.7 times of that of bulk g-C3N4, which makes it a promising visible light photocatalyst for future applications for water treatment and environmental remediation.     

Efficient overall water splitting under visible-light irradiation on (Ga(1-x)Zn(x))(N(1-x)O(x)) dispersed with Rh-Cr mixed-oxide nanoparticles: Effect of reaction conditions on photocatalytic activity

The photocatalytic activity of (Ga(1-x)Zn(x))(N(1-x)O(x)) loaded with Rh-Cr mixed-oxide (Rh(2-y)Cr(y)O3) nanoparticles for overall water splitting under visible-light irradiation (lambda > 400 nm) is investigated with respect to reaction pH and gas pressure. The photocatalytic performance of the catalyst is found to be strongly dependent on the pH of the reactant solution but largely independent of gas pressure. The present photocatalyst exhibits stable and high photocatalytic activity in an aqueous solution of pH 4.5 for 72 h. The photocatalytic performance is much lower at pH 3.0 and pH 6.2, attributable to corrosion of the cocatalyst and hydrolysis of the catalyst. The dispersion of Rh(2-y)Cr(y)O3 as a cocatalyst on the (Ga(1-x)Zn(x))(N(1-x)O(x)) surface promotes hydrogen evolution, which is considered to be the rate-determining step for overall water splitting on this catalyst.     

纳米TiO2薄膜耦合光催化氧化还原反应脱除水中无机氮

由溶胶-凝胶法制备了固定化二氧化钛薄膜,研究了薄膜催化剂光催化脱除含氨氮-亚硝酸氮混合液中无机氮的活性.考察了溶胶制备工艺、催化反应条件(尤其pH)对光催化活性的影响.实验证明:酸性条件有利于亚硝酸氮的还原,碱性条件有利于氨氮的氧化,通过调节pH可以获得光催化氧化氨氮和还原亚硝酸氮耦合效果.如果加入甲酸维持酸性务件,反应0.5 h后再将pH调回碱性,可以大大提高光催化脱氮的效果:经过2 h的光催化反应,二氧化钛膜催化总氮去除率可达50%以上.经多次试验证明附载二氧化钛薄膜不脱落,光催化活性未见减弱,可重复利用.提出了光催化脱氮的反应机理.     

RuO2-loaded beta-Ge3N4 as a non-oxide photocatalyst for overall water splitting

Germanium nitride beta-Ge3N4 dispersed with RuO2 nanoparticles is presented as the first example of a non-oxide photocatalyst for the stoichiometric decomposition of H2O into H2 and O2. All of the successful photocatalysts developed for overall water splitting over the past 30 years have been based on oxides of metals. The discovery of a non-oxide photocatalyst, such as nitrides and oxynitrides, achieving the same function is therefore expected to stimulate research on non-oxide photocatalysts. New opportunities for progress in the development of visible light-driven photocatalysis can thus be expected, as the higher valence band positions of metal nitrides compared to the corresponding metal oxides provide narrower band gaps, which are suitable for visible light activity.     

Preparation of a colloidal array of NaTaO3 nanoparticles via a confined space synthesis route and its photocatalytic application

The confined space synthesis method has been applied to the preparation of sodium tantalate (NaTaO(3)); hydrothermal reaction of NaOH and Ta(2)O(5) was carried out in the pores of a three-dimensional mesoporous carbon, which was replicated by the colloidal array of silica nanospheres (SNSs) 20 nm in size. This approach led to the formation of a colloidal array of NaTaO(3) nanoparticles 20 nm in size with a surface area of 34 m(2) g(-1). The photocatalytic performance of the colloidal array of NaTaO(3) nanoparticles for overall water splitting under UV irradiation (λ > 200 nm) was evaluated after loading a NiO cocatalyst onto NaTaO(3) samples. The NiO-loaded NaTaO(3) nanoparticles showed photocatalytic activity for overall water splitting more than three times as high as non-structured bulk NaTaO(3) particles.     

Overall Water Splitting on the Transition‐Metal Oxynitride Photocatalyst LaMg1/3Ta2/3O2N over a Large Portion of the Visible‐Light Spectrum

One of the main targets of studies on water splitting photocatalysts is to develop semiconductor materials with narrower bandgaps capable of overall water splitting for efficient harvesting of solar energy. A series of transition‐metal oxynitrides, LaMg_xTa_1?xO_1+3xN_2?3x (x≥1/3), with a complex perovskite structure was reported as the first example of overall water splitting operable at up to 600 nm. The photocatalytic behavior of LaMg_1/3Ta_2/3O₂N was investigated in detail in order to optimize photocatalyst preparation and water‐splitting activity. Various attempts exploring photocatalyst preparation steps, that is, cocatalyst selection, coating material and method, and synthesis method for the oxide precursor, revealed photocatalyst structures necessary for achieving overall water splitting. Careful examination of photocatalyst preparation procedures likely enhanced the quality of the produced photocatalyst, leading to a more homogeneous coating quality and semiconductor particles with fewer defects. Thus, the photocatalytic activity for water splitting on LaMg_1/3Ta_2/3O₂N was largely enhanced.     

化学镀法制备CoP量子点修饰g-C3N4用于光催化产氢（英文）

光催化分解水制氢被认为是解决当前能源危机和环境污染问题的重要途径之一.在众多光催化剂中,石墨相氮化碳(g-C3N4)因其具有高的热稳定性、高的化学稳定性、合适的能带位置以及成本低廉等优点,受到光催化领域研究者的广泛关注,成为研究热点.然而,由于g-C3N4的禁带宽度较大(Eg=2.7 eV),导致其对可见光的响应较差,而且光生电子-空穴对在其中易于复合,从而导致其光催化产氢活性较低.已有研究表明,助催化剂可以有效地促进催化剂中光生载流子的分离和传输,从而提高光催化剂的光催化活性和氢气的产生速率.目前使用最广泛的助催化剂多为贵金属(Au,Ag,Pt和Pd等),然而贵金属储量低、成本高,极大地限制了其实际应用.因而,开发适用于光催化水分解制氢的非贵金属助催化剂成为该领域的研究热点.其中,用非贵金属助催化剂修饰g-C3N4制备高效光催化剂分解水制氢技术引起了人们极大的兴趣.过渡金属磷化物(FeP,CoP,CuP,NiP等)是一种有效的光催化辅助催化剂.然而,这些金属磷化物的合成通常使用有毒的有机磷化合物和白磷或涉高温煅烧.特别是在传统水热法制备金属磷化物过程中会释放大量氢气,导致容器内压力过高,造成较大的安全问题.据报道,在这些磷化物中,磷化钴由于其合适的能带结构和较高的导电性,作为光催化分解水助催化剂受到了广泛关注.然而,截至目前,关于磷化钴作为助催化剂用于光催化的实用技术报道很少,特别是在温和条件下制备磷化钴修饰的g-C3N4复合光催化剂的研究还有待进行.本文研究了以CoP作为助催化剂来改进g-C3N4(制备g-C3N4/CoP),并用于光催化水裂解制氢气.复合光催化剂g-C3N4/CoP经由两步反应合成.第一步采用尿素热分解法制备g-C3N4,第二步通过化学镀法将CoP修饰在g-C3N4表面.采用XRD,TEM,UV-DRS和XPS等手段表征了g-C3N4/CoP光催剂的性质.结果表明,CoP以量子点(QDs)形式均匀分布在g-C3N4表面,显著提高了g-C3N4的光催化活性.不同CoP负载量的样品中,g-C3N4/CoP-4%表现出优异的光催化活性,H2生成速率为936μmol g^-1 h^-1,甚至高于4%Pt负载的g-C3N4(H2的生成速率仅为665μmol g^-1 h^-1).从紫外可见光谱上看,g-C3N4在451 nm达到吸收波长上限,但与CoP复合后,g-C3N4/CoP-4%的吸收波长上限延展到497 nm.此外,光致发光和光电流测试结果证实,将CoP量子点负载到g-C3N4上不仅可以降低光生电荷-空穴对的复合,而且可以改善光生e--h+对的转移,从而提高光催化剂的产氢性能.这项工作为开发高效的非贵金属助催化剂修饰g-C3N4的技术提供了一个可行策略,所制材料在光催化制氢领域显示出潜在的应用前景.     

两步水热法合成Sn_2Nb_2O_7纳米晶及其高效可见光分解水制氢性能（英文）

铌基半导体光催化材料因其具有独特的晶体结构和能带结构在光催化分解水制氢领域受到科研工作者的高度关注.然而,大多数铌基半导体光催化剂仅能够在紫外光驱动下实现光催化分解水制氢,具有可见光响应的铌基半导体光催化剂不仅数量少而且活性较低,因此发展新型纳米铌基半导体光催化剂并实现其高效可见光催化分解水产氢具有重要的学术和实用意义.具有烧绿石构型的Sn_2Nb_2O_7材料由于具有较窄的禁带宽度(2.4 e V)和合适的导带和价带电势在可见光催化分解水制氢方面引起了科研人员广泛的兴趣.然而,目前报道的利用高温固相法制备的块体Sn_2Nb_2O_7材料由于颗粒尺寸较大和比表面积较小而导致光催化活性较差.因此,发展一种简便高效的制备方法实现纳米Sn_2Nb_2O_7材料的可控制备进而提高其可见光催化活性仍具有一定的挑战性.我们发展了一种简便的两步水热合成方法实现了Sn_2Nb_2O_7纳米晶的可控制备.扫描电镜和透射电镜测试结果表明,通过两步水热法得到的Sn_2Nb_2O_7纳米颗粒具有较好分散度,其平均颗粒尺寸为20 nm.X射线衍射测试结果也进一步证明,通过两步水热法可以实现Sn_2Nb_2O_7纳米晶的可控制备.比表面积测试结果表明,Sn_2Nb_2O_7纳米晶的比表面积约为52.2 m~2/g,远远大于固相法制备的块体Sn_2Nb_2O_7材料(2.3 m~2/g).大量研究表明,大的比表面积有利于半导体催化材料催化活性的提升.通过考查所制备的Sn_2Nb_2O_7纳米晶的可见光分解水制氢能力,对其催化性能进行了评价.研究结果表明,以乳酸为空穴消耗剂,负载0.3wt.%Pt纳米颗粒作为助催化剂的Sn_2Nb_2O_7纳米晶表现出优异的可见光催化分解水产氢性能,其产氢速率是块体Sn_2Nb_2O_7材料的5.5倍.Sn_2Nb_2O_7纳米晶可见光催化分解水产氢性能提高的主要原因是其具有高分散度的纳米颗粒、较大的比表面积和更正的价带电势.首先,颗粒尺寸的纳米化能够显著减小光生电子和空穴的迁移距离,实现光生载流子快速迁移到催化剂表面进而参与催化反应;其次,大的比表面积能够提供更多的催化活性位点,进而有利于催化活性的提高;最后,X射线光电子能谱测试表明,Sn_2Nb_2O_7纳米晶具有更正的价带电势,研究表明,价带电势越正,其光生空穴氧化能力越强.在光催化分解水制氢过程中,具有较强氧化能力的光生空穴通过与空穴牺牲剂乳酸快速反应而被消耗掉,抑制了光生电子与空穴的复合,进而导致其具有较高的光催化产氢活性.     

Role of Dimensionality for Photocatalytic Water Splitting: CdS Nanotube versus Bulk Structure

Using state-of-the-art density functional theoretical calculations, we have modelled a facetted CdS nanotube (NT) catalyst for photocatalytic water splitting. The overall photocatalytic activity of the CdS photocatalyst has been predicted based on the electronic structures, band edge alignment, and overpotential calculations. For comparisons, we have also investigated the water splitting process over bulk CdS. The band edge alignment along with the oxygen evolution reaction/hydrogen evolution reaction (OER/HER) mechanism studies help us find out the effective overpotential for the overall water splitting on these surfaces. Our study shows that the CdS NT has a highly stabilized valence band edge compared to that of bulk CdS owing to strong p–d mixing. The highly stabilized valence band edge is important for the hole-transfer process and reduces the risk of electron-hole recombination. CdS nanotube requires less overpotential for water oxidation reaction than the bulk CdS. Our findings suggest that the efficiency of the water oxidation/reduction process further improves in CdS as we reduce its dimensionality, that is going from bulk CdS to one-dimensional nanotube. Furthermore, the stabilized valence band edge of CdS nanotube also improves the photostability of CdS, which is a problem for bulk CdS.     

富表面氧空位Fe2O3/ZnO催化剂在光催化合成氨中的应用

光催化合成氨是一种绿色节能的合成氨技术,设计制造丰富的表面氧空位和异质结构是促进氮分子活化和抑制电子-空穴复合的重要方法。我们以乙二醇作为还原剂,采用溶剂热法制备合成了Fe2O3/ZnO光催化剂,利用X射线衍射(XRD)、透射电镜(TEM)、电子顺磁共振(EPR)、紫外-可见漫反射(UV-Vis DRS)、荧光光谱(PL)及光电流(PC)对Fe2O3/ZnO催化剂进行表征,并考察了Fe2O3/ZnO催化剂在常温、常压下的光催化合成氨的性能。4%Fe2O3/ZnO催化剂在无牺牲剂下用于光催化合成氨,有较好的光催化效率和稳定性,其合成氨效率达到2059μmol·L-1·g-1·h-1。其高催化效率归因于:可见光区域吸收的提高、氮分子在表面氧空位与Fe3+活性中心上的协同活化及光生电子与空穴的高分离效率。     

石墨相氮化碳纳米管的合成及光催化产氢性能

通过硬模板法,采用氰胺前驱物和二氧化硅纳米管(SiO₂-NTs)模板,合成石墨相氮化碳纳米管(CN-NTs)光催化剂。采用扫描电镜(SEM)、透射电镜(TEM)、X射线粉末衍射(XRD)、傅立叶变换红外光谱(FT-IR)、氮气吸附/脱附测试、紫外可见漫反射光谱(UV-Vis DRS)、荧光光谱、热重分析(TGA)等手段对CN-NTs催化剂的结构与性能进行表征。结果表明,CN-NTs的化学组成是石墨相氮化碳(g-C₃N₄),形貌为均匀的纳米管,且是介孔材料。与体相氮化碳(B-CN)和介孔石墨相氮化碳(mpg-CN)相比,CN-NTs的光吸收带边蓝移到440 nm,荧光发射谱的峰强减弱。在可见光(λ>420 nm)照射下,CN-NTs具有较高的光催化分解水活性,产氢速率为58 μmol/h,且表现出良好的光催化活性稳定性和化学结构稳定性。研究结果表明纳米管状结构能有效促进g-C₃N₄半导体激子解离,提高光生电子-空穴的分离效率,进而显著优化g-C₃N₄的光催化产氢性能。     

Rh/Cr2O3 and CoOx Cocatalysts for Efficient Photocatalytic Water Splitting by Poly (Triazine Imide) Crystals

In situ photo-deposition of both Pt and CoO_x cocatalysts on the facets of poly (triazine imide) (PTI) crystals has been developed for photocatalytic overall water splitting. However, the undesired backward reaction (i.e., water formation) on the noble Pt surface is a spontaneously down-hill process, which restricts their efficiency to run the overall water splitting reaction. Herein, we demonstrate that the efficiency for photocatalytic overall water splitting could be largely promoted by the decoration of Rh/Cr₂O₃ and CoO_x as H₂ and O₂ evolution cocatalysts, respectively. Results reveal that the dual cocatalysts greatly extract charges from bulk to surface, while the Rh/Cr₂O₃ cocatalyst dramatically restrains the backward reaction, achieving an apparent quantum efficiency (AQE) of 20.2 % for the photocatalytic overall water splitting reaction.     

Characterization of Rh-Cr mixed-oxide nanoparticles dispersed on (Ga(1-x)Zn(x))(N(1-x)Ox) as a cocatalyst for visible-light-driven overall water splitting

The structure of Rh-Cr mixed-oxide (Rh(2)(-)(y)Cr(y)O(3)) nanoparticles dispersed on (Ga(1)(-)(x)Zn(x))(N(1)(-)(x)O(x)) is characterized by electron microscopy and X-ray spectroscopy. The Rh(2)(-)(y)Cr(y)O(3) nanoparticle is an efficient cocatalyst for photocatalytic overall water splitting on the (Ga(1)(-)(x)Zn(x))(N(1)(-)(x)O(x)) solid solution and is loaded onto the catalyst by impregnation from an aqueous solution containing Na(3)RhCl(6).2H(2)O and Cr(NO(3))(3).9H(2)O followed by calcination in air. Impregnation of the (Ga(1)(-)(x)Zn(x))(N(1)(-)(x)O(x)) with 1 wt % Rh and 1.5 wt % Cr followed by calcination at 623 K for 1 h provides the highest photocatalytic activity. Structural analyses reveal that the activity of this photocatalyst is strongly dependent on the generation of trivalent Rh-Cr mixed-oxide nanoparticles with optimal composition and distribution.     

离子热处理合成氮缺陷石墨相氮化碳及其光解水制氢性能

以尿素和二氰二胺为原料热聚合得到石墨相氮化碳,分别采用直接二次煅烧和熔盐离子热后热处理在不同温度下对产物进行后热处理,得到氮缺陷氮化碳CN和CNS。利用X射线衍射(XRD)、紫外-可见漫反射光谱(UV-Vis DRS)、透射电镜(TEM)等手段对所制备样品进行表征和分析,探讨了不同热处理温度和加热方法对催化剂微观聚合结构的影响;同时以光解水制氢为测试方法,考察了催化剂的可见光催化性能。结果表明,熔盐离子热更有利于氮化碳的层间聚合,得到高结晶度材料;在面内七嗪聚合单元中引入氮缺陷,产生末端氰基,优化电荷密度分布,增强电荷流动性;克服粒子尺寸效应,扩展催化剂的光吸收范围;当后热处理温度为500℃时,制备的CNS-500表现出优异的光解水制氢活性,是同温度下直接热处理得到的催化剂的3.84倍。     

Synthesis and photocatalytic properties of a new heteropolyoxoniobate compound: K10[Nb2O2(H2O)2][SiNb12O40)·12H2O

The synthesis and photocatalytic properties of a heteropolyoxoniobate, K(10)[Nb(2)O(2)(H(2)O)(2)][SiNb(12)O(40)]·12H(2)O (1), are reported, revealing an important role of Zr(4+) additives in the crystallization. Compound 1 exhibits overall photocatalytic water splitting activity, and its photocatalytic activity is significantly higher than that of Na(10)[Nb(2)O(2)][SiNb(12)O(40)]·xH(2)O (2). Fluorescence lifetime measurements suggest that the enhanced photocatalytic activity of 1 likely results from a larger yield of longer-lived charge trapping states in 1 due to the coordination of one water molecule to the bridging Nb(5+), leading to highly unsymmetrical seven-coordinated Nb(5+) sites.     

Improved photocatalytic activity of TiO_2 produced by an alcohothermal approach through in-situ decomposition of NH_4HCO_3

High crystallinity of TiO_2 was prepared by a modified alcohothermal method, in which titanium isopropoxide was used as the titania precursor, absolute ethanol as the reaction medium, and NH_4HCO_3 as the raw materials for release of water, ammonia and carbon dioxides via in-situ decomposition. The X-ray powder diffraction(XRD) and transmission electron microscope(TEM) measurements showed that water and ammonia from the in-situ decomposition of NH_4HCO_3 played an important role in conducting the size, shape, crystallinity and microstructure of TiO_2. The photoluminescence spectroscopy and photocurrent measurements indicated that enhanced crystallinity could hinder the recombination and promote the separation of electron-hole pairs in TiO_2, which contribute to the improvement of photocatalytic activity.Methyl orange photodegradation under UV light confirmed that high crystallinity of TiO_2 did present a high photocatalytic activity due to the effective separation of photoinduced charges.     

Characterization of ruthenium oxide nanocluster as a cocatalyst with (Ga(1-x)Zn(x))(N(1-x)Ox) for photocatalytic overall water splitting

The formation and structural characteristics of Ru species applied as a cocatalyst on (Ga(1)(-)(x)()Zn(x)())(N(1)(-)(x)()O(x)()) are examined by scanning electron microscopy, X-ray photoelectron spectroscopy, and X-ray absorption spectroscopy. RuO(2) is an effective cocatalyst that enhances the activity of (Ga(1)(-)(x)()Zn(x)())(N(1)(-)(x)()O(x)()) for overall water splitting under visible-light irradiation. The highest photocatalytic activity is obtained for a sample loaded with 5.0 wt % RuO(2) from an Ru(3)(CO)(12) precursor followed by calcination at 623 K. Calcination is shown to cause the decomposition of initial Ru(3)(CO)(12) on the (Ga(1)(-)(x)()Zn(x)())(N(1)(-)(x)()O(x)()) surface (373 K) to form Ru(IV) species (423 K). Amorphous RuO(2) nanoclusters are then formed by an agglomeration of finer particles (523 K), and the nanoclusters finally crystallize (623 K) to provide the highest catalytic activity. The enhancement of catalytic activity by Ru loading from Ru(3)(CO)(12) is thus shown to be dependent on the formation of crystalline RuO(2) nanoparticles with optimal size and coverage.     

Overall water splitting on (Ga(1-x)Zn(x))(N(1-x)O(x)) solid solution photocatalyst: relationship between physical properties and photocatalytic activity

The physical and photocatalytic properties of a novel solid solution between GaN and ZnO, (Ga(1-x)Zn(x))(N(1-x)O(x)), are investigated. Nitridation of a mixture of Ga(2)O(3) and ZnO at 1123 K for 5-30 h under NH(3) flow results in the formation of a (Ga(1-x)Zn(x))(N(1-x)O(x)) solid solution with x = 0.05-0.22. With increasing nitridation time, the zinc and oxygen concentrations decrease due to reduction of ZnO and volatilization of zinc, and the crystallinity and band gap energy of the product increase. The highest activity for overall water splitting is obtained for (Ga(1-x)Zn(x))(N(1-x)O(x)) with x = 0.12 after nitridation for 15 h. The crystallinity of the catalyst is also found to increase with increasing the ratio of ZnO to Ga(2)O(3) in the starting material, resulting in an increase in activity.     

Two-dimensional ruthenium nanoparticles between graphite layers: The effect of reduction temperature

A mixture of graphite powder and ruthenium chloride (III) anhydrous was treated at 723 K under 0.3 MPa chlorine for 3 days, followed by reduction under 40 kPa of hydrogen for 1 h to produce ruthenium metal particles intercalated between graphite layers (Ru-GIC). The structures of ruthenium particles depended on the reduction temperatures. Sheet-like ruthenium particles with 1–3 nm thickness and 10 to several hundred nm width containing numerous irregularly shaped holes with round edge, were formed by reduction at 573 K. A Ru-GIC sample treated at 653 K possessed two-dimensional ruthenium nanosheets with hexagonal holes (straight lines intersect at an angle of 120°) in a similar range of thickness and width. On the other hand, Ru-GIC samples reduced at 773 and 823 K showed two-dimensional plate morphology with a thickness of 1–4 nm. In addition, ruthenium nanoparticles supported on the graphite surface (Ru/Gmix) were also prepared from a slurry of ruthenium chloride (III) hydrate and graphite powder by impregnation and hydrogen reduction. The ruthenium particles in Ru/Gmix were spherical at about 3.6 nm, and the reduction temperature did not affect their particles size. Both Ru-GIC and Ru/Gmix samples were evaluated for cinnamaldehyde (CAL) hydrogenation in supercritical carbon dioxide solvent at 323 K, and they were active to produce cinnamyl alcohol (COL) and hydrocinnamaldehyde (HAL). However, Ru-GIC samples showed higher COL selectivity than Ru/Gmix prepared at the same reduction temperature, and COL selectivity over Ru-GIC increased with the reduction treatments at 773 and 823 K.     

原位构筑质子化氮化碳/碳化钛光催化制氢肖特基异质结

氢气因其具有高燃烧热、可再生性以及燃烧产物无污染等优势被认为是一种绿色可再生能源,是取代化石燃料的候选能源之一.然而,如何利用自然界中丰富的太阳能和水资源实现光分解水制氢的关键在于开发高效的光催化剂.在尺寸明确、能级带隙匹配的纳米材料间进行完美的界面复合(异质结构筑)是实现高效太阳能-氢能转换的最佳途径.石墨相氮化碳(CN)材料因其电子结构可调和化学性能稳定等特性被光催化界所关注.然而,氮化碳材料较弱的电学性能如电荷传输能力差及电子-空穴对复合率高导致其表现出较低的光催化制氢效率.基于此,我们用盐酸对氮化碳进行质子化处理,使材料表面电荷发生改变,从而实现氮化碳的电子带隙调节和电导率提升.在此基础上,将二维碳化钛原位负载于质子化的氮化碳(PCN)纳米片表面构筑肖特基结.PCN纳米片与碳化钛纳米片间的良好界面接触促进了电荷在材料界面上传输,进而加速了氮化碳材料的电荷分离,实现了氮化碳光催化剂活性的提升.Zeta电位测试结果显示,CN和PCN的表面电位分别为?9.5和27.3 mV,表明质子化处理可以有效改变材料表面电荷,并促其与碳化钛纳米片进行静电组装.该结果进一步得到了扫描电子显微镜(SEM)和原子力显微镜(AFM)的证实.改变表面电荷使氮化碳材料的能带宽度由2.53 eV(CN)减小到2.41 eV(PCN),增强了可见光区吸收.同时,PCN的光电流密度提升了约4倍,电子阻抗和激发态电子的辐射复合都显著降低.将PCN与碳化钛复合制得复合材料(PCN-x,x=10,20,40),实验结果表明5 g的PDN最佳负载碳化钛的量为20 mg(PCN-20).在标准太阳模拟器的可见光区(>420 nm),复合材料PCN-20的光催化水分解产氢量可达2181μmol·g-1,是CN催化剂的约5.5倍,PCN的2.7倍,并且经过5次产氢循环后PCN-20仍具有稳定的氢气释放速率.以上结果表明,氮化碳材料可以通过质子化处理以及与适量的碳化钛复合实现光催化产氢性能的提升,其中碳化钛在体系中起助催化剂的作用.该研究结果可为其他半导体光催化剂的性能优化以及非贵金属助催化剂的研究提供新思路.