Structure and reflective properties of Al-Cu-Fe quasicrystalline thin film prepared by laser induced arc method

Al-Cu-Fe thin films were prepared by laser induced arc (laser-arc) method from a single source-Al63Cu25Fe12 alloy, which was proved to consist of quasicrystalline phase together with approximant phase. The composition of the deposited films meets the requirement for formation of icosahedral symmetry phase. Quasicrystalline phase was obtained after annealing the amorphous as-deposit film samples. The optical properties of the samples were investigated. Thin film samples of Al, Cu and Fe deposited under the same condition were employed for comparison. The results showed specific reflective properties of Al-Cu-Fe quasicrystal thin film in some wavelength range. The optical conductivity of the films exhibited a negative peak, centered about 440 nm in range of 190to 800 nm. The Al-Cu-Fe quasicrystal thin films could absorb almost all the ray in the wavelength range from 420nm to 450 nm. The ratio of absorption was greater than 99%.     

Laser radiation effects on optical and structural properties of nanostructure CdSe thin film

Cadmium selenide (CdSe) thin films were deposited on a glass substrate using the thermal evaporation method at room temperature. The changes in the optical properties (optical band gap and absorption coefficient) after irradiation by TEA N₂ laser at different energies were measured in the wavelength range 190–800 nm using a spectrophotometer. It was found that the optical band gap is decreased after irradiating the thin films. The samples were characterized using X-ray diffraction (XRD), and the grain size of the CdSe thin film was calculated from XRD data, which was found to be 41.47 nm as-deposited. It was also found that grain size increases with laser exposure. The samples were characterized using a scanning electron microscope and it was found that big clusters were formed after irradiation by TEA N₂ laser.     

Chemical bath-deposited ZnS thin films: Preparation and characterization

Chemical bath deposition of ZnS thin films from NH₃/SC(NH₂)₂/ZnSO₄ solutions has been studied. The effect of various process parameters on the growth and the film quality are presented. The influence on the growth rate of solution composition and the structural, optical properties of the ZnS thin films deposited by this method have been studied. The XRF analysis confirmed that volume of oxygen of the as-deposited film is very high. The XRD analysis of as-deposited films shows that the films are cubic ZnS structure. The XRD analysis of annealed films shows the annealed films are cubic ZnS and ZnO mixture structure. Those results confirmed that the as-deposited films have amorphous Zn(OH)₂. SEM studies of the ZnS thin films grown on various growth phases show that ZnS film formed in the none-film phase is discontinuous. ZnS film formed in quasi-linear phase shows a compact and a granular structure with the grain size about 100 nm. There are adsorbed particles on films formed in the saturation phase. Transmission measurement shows that an optical transmittance is about 90% when the wavelength over 500 nm. The band gap (E_g) value of the deposited film is about 3.51 eV.     

Phase transformation of nanostructured titanium dioxide thin films grown by sol–gel method

Nanostructured TiO₂ thin films were deposited on quartz glass at room temperature by sol–gel dip coating method. The effects of annealing temperature between 200^∘C to 1100^∘C were investigated on the structural, morphological, and optical properties of these films. The X-ray diffraction results showed that nanostructured TiO₂ thin film annealed at between 200^∘C to 600^∘C was amorphous transformed into the anatase phase at 700^∘C, and further into rutile phase at 1000^∘C. The crystallite size of TiO₂ thin films was increased with increasing annealing temperature. From atomic force microscopy images it was confirmed that the microstructure of annealed thin films changed from column to nubbly. Besides, surface roughness of the thin films increases from 1.82 to 5.20 nm, and at the same time, average grain size as well grows up from about 39 to 313 nm with increase of the annealing temperature. The transmittance of the thin films annealed at 1000 and 1100^∘C was reduced significantly in the wavelength range of about 300–700 nm due to the change of crystallite phase. Refractive index and optical high dielectric constant of the n-TiO₂ thin films were increased with increasing annealing temperature, and the film thickness and the optical band gap of nanostructured TiO₂ thin films were decreased.     

Optical characterization of tin containing novel chalcogen rich glassy semiconductors

Amorphous thin film materials with different compositions of Se_80?xTe₂₀Sn_x (0 ≤ x ≤ 10) system have been deposited on glass substrates by a well known thermal evaporation technique. Structural characterization of different compositions of aforementioned system has been done by Raman spectroscopy. The optical properties of thin films have been studied in the wavelength range 200–1100 nm by the utilization of the optical absorbance spectra of deposited thin films. To calculate the optical band gap from the optical absorption spectra, we have used Tauc model that follows the mechanism of allowed ‘non-direct electronic transition’. Subsequently, we have determined the energy band gap, metallization criterion and refractive index of thin films of aforesaid system. The variation in optical properties with composition has been interpreted in terms of density of defect states.     

Correlation between microstructure and optical properties of nano-crystalline TiO2 thin films prepared by sol-gel dip coating

Titanium dioxide thin films have been prepared from tetrabutyl-orthotitanate solution and methanol as a solvent by sol-gel dip coating technique. TiO₂ thin films prepared using a sol-gel process have been analyzed for different annealing temperatures. Structural properties in terms of crystal structure were investigated by Raman spectroscopy. The surface morphology and composition of the films were investigated by atomic force microscopy (AFM). The optical transmittance and reflectance spectra of TiO₂ thin films deposited on silicon substrate were also determined. Spectroscopic ellipsometry study was used to determine the annealing temperature effect on the optical properties and the optical gap of the TiO₂ thin films. The results show that the TiO₂ thin films crystallize in anatase phase between 400 and 800 °C, and into the anatase-rutile phase at 1000 °C, and further into the rutile phase at 1200 °C. We have found that the films consist of titanium dioxide nano-crystals. The AFM surface morphology results indicate that the particle size increases from 5 to 41 nm by increasing the annealing temperature. The TiO₂ thin films have high transparency in the visible range. For annealing temperatures between 1000 and 1400 °C, the transmittance of the films was reduced significantly in the wavelength range of 300-800 nm due to the change of crystallite phase and composition in the films. We have demonstrated as well the decrease of the optical band gap with the increase of the annealing temperature.     

Photoluminescence study of nitrogen-doped p-type Mg x Zn1−x O nanocrystalline thin film grown by plasma-assisted molecular beam epitaxy

Tin sulfide thin films have been grown on glass substrates by chemical bath deposition technique (CBD) at room temperature and irradiated with UV light source of wavelength 355 nm. The effect of UV illumination on the physical properties of the films was compared with that of the as-prepared film. Though the thickness of the films was unaltered after illumination, the structural, optical and electrical properties changed considerably. Structural studies showed the polycrystalline nature of the UV-illuminated sample, whereas the as-prepared film was mono crystalline. Both films were orthorhombic structure with Sn₂S₃ phase. The optical properties of the films were systematically studied using the optical absorbance and reflection spectra. Studies on the reflection spectra showed higher reflectance in visible and infrared region for the UV-illuminated films and lower reflectance in the infrared region for the as-prepared one. The variation of the refractive index of the samples was also analyzed. The optical absorption coefficient and the optical band gap energy of the films were evaluated. The irradiated film exhibited lower band gap of 1.74 eV than the value of as-prepared film, i.e., 1.77 eV. The measured resistivity of the tin sulfide thin films was found to be of the order of 10⁸ and 10⁹ Ωcm for UV-illuminated and as-prepared films, respectively. The SEM images showed the presence of worm-like nanostructures with almost similar appearance in both the films.     

Hydrogenation of Pd-capped Mg thin films prepared by DC magnetron sputtering

Structural and optical properties of pure Mg thin film coated with Pd have been investigated. Pd-capped Mg thin films had been prepared by DC magnetron sputtering. This work presents an ex situ study on hydrogenation and dehydrogenation kinetics of Pd/Mg films at different conditions using XRD, AFM and optical spectrophotometer. We have succeeded to load thin films of Mg to MgH₂ at normal temperature and normal pressure of hydrogen gas. In hydrogenation, α-MgH₂ phase of magnesium hydride was observed in hydrogenated films at 200 °C and γ-MgH₂ at 250 °C respectively. The desorption kinetics in vacuum also revealed the phase transformation α-MgH₂ to γ-MgH₂. A reflectance change was observed in hydrogenated films in comparison of as deposited thin film. Hydrogenated (H loaded) samples were observed partially transparent in comparison of as deposited.     

Influence of thermal annealing on optical and structural properties change in Bi-doped Ge30Se70 thin films

The effect of annealing on the structural and optical properties of thermally evaporated Ge₃₀Se₇₀ and Ge₃₀Se₆₀Bi₁₀ thin films is reported in this paper. The prepared films were thermally annealed at 250°C to optimize the optical properties which can be used for the optical device fabrication. X-ray diffraction study revealed no structural transformation whereas the surface morphology changed as observed from scanning electron microscopy. The optical properties of the deposited and annealed films have been investigated by using a UV–VIS–NIR spectrophotometer in the wavelength range of 400–1100?nm. The optical band gap of the Ge₃₀Se₇₀ annealed film is found to be increased while the energy gap of the Bi-doped annealed Ge₃₀Se₆₀Bi₁₀ thin film decreased which is explained by the chemical disorderness, defect states and density of localized states in the mobility gap. The Tauc parameter and Urbach energy which measure the degree of disorder changed with the annealing process. The transmittivity increases and the absorption power decreases in the Ge₃₀Se₇₀ annealed film, whereas the reverse effect is noticed for the annealed Ge₃₀Se₆₀Bi₁₀ thin film. The irreversible nature of this change can be useful for optical recording purposes.     

Optical and structural properties of PbI<Subscript>2</Subscript> thin film produced via chemical dipping method

PbI₂ thin films were deposited on glass substrates via chemical bath deposition. The characteristics of PbI₂ thin films were examined through their structural and optical properties. X-ray diffraction spectra showed the presence of rhombohedral structure and atom planes were subject to change with the pH of the bath. Scanning electron microscope indicated uniform distribution of grains. Optical properties were examined via UV–VIS; optical spectrum of the thin films was measured at the range of 200–1100 nm wavelength. Optimum pH levels for producing thin films were found to be pH 4–5. It has been observed that transmission and optical band gap (E _g) increased with the pH of the bath, which varied between 66–95 and 2.24–2.50 %, respectively; on the other hand film thickness of PbI₂ thin films was decreased with the pH of the bath. Energy-dispersive X-ray spectroscopy analysis were in accordance with theoretical value of PbI₂ at pH = 4 and 5. Refractive index was negatively correlated with pH of the chemical bath; it has been calculated as 1.97, 1.40, 1.29 and 1.24 for the films produced at pH 2, 3, 4 and 5. The results of the study were compared with similar studies in the literature.     

Nanocrystalline formation and optical properties of germanium thin films prepared by physical vapor deposition

Amorphous and nanocrystalline germanium thin films were prepared on glass substrates by physical vapor deposition (PVD). The influence of thermal annealing on the characteristics of the Ge thin films has been investigated. X-ray diffraction (XRD) and SEM show amorphous structure of films deposited at room temperature. After thermal annealing, the crystallinity was improved when the annealing temperature increases. The Ge thin films annealed at different temperatures in air were nanocrystalline, having the face-centered cubic structure with preferred orientation along the 〈1 1 1〉 direction. The nanostructural parameters have been evaluated by using a single-order Voigt profile analysis. Moreover, the analysis of the optical transmission and reflection behavior was carried out. The values of direct and indirect band gap energies for amorphous and nanocrystalline phases are 0.86±0.02, 0.65±0.02 and 0.79±0.02, 0.61±0.02 eV, respectively. In addition, the complex optical functions for the wavelength range 600-2200 nm are reported. The refractive index of the nanocrystalline phase drops from 4.80±0.03 to 2.04±0.02, and amorphous phase changes from 5.18±0.03 to 2.42±0.02 for the whole wavelength range. The dielectric functions ε₁ and ε₂ of the deposited films were recorded as a function of wavelength within the range from 600 to 2200 nm.     

Low temperature deposition of transparent conducting ITO/Au/ITO films by reactive magnetron sputtering

Transparent conducting indium tin oxide/Au/indium tin oxide (ITO) multilayered films were deposited on unheated polycarbonate substrates by magnetron sputtering. The thickness of the Au intermediated film varied from 5 to 20 nm. Changes in the microstructure, surface roughness and optoelectrical properties of the ITO/Au/ITO films were investigated with respect to the thickness of the Au intermediated layer. X-ray diffraction measurements of ITO single layer films did not show characteristic diffraction peaks, while ITO/Au/ITO films showed an In₂O₃ (2 2 2) characteristic diffraction peak. The optoelectrical properties of the films were also dependent on the presence and thickness of the Au thin film. The ITO 50 nm/Au 10 nm/ITO 40 nm films had a sheet resistance of 5.6 Ω/□ and an average optical transmittance of 72% in the visible wavelength range of 400-700 nm. Consequently, the crystallinity, which affects the optoelectrical properties of ITO films, can be enhanced with Au intermediated films.     

Optical properties of nanoscale BiFeO3/BaTiO3/Ni0.5Zn0.5Fe2O4 composite films obtained by the pulsed-laser deposition method

Nanoscale (30–100 nm) films of BiFeO₃/BaTiO₃/Ni_0.5Zn_0.5Fe₂O₄ complex composition have been obtained by the pulsed-laser deposition method. Optical properties of the films were studied in the wavelength range of 250–1000 nm. It is shown that the optical properties of amorphous films deposited at room temperature are explained by the Tauc model for amorphous semiconductors. An increase in the optical gap from 1.7 to 1.95 eV was observed with decreasing film thickness. Allowed direct-band transitions (E _g = 3.1 eV) were observed after annealing of films independent of their thickness.     

Optoelectronics properties of TiO<Subscript>2</Subscript>:Cu thin films obtained by sol gel method

In this research, Cu-doped TiO₂ thin films have been successfully deposited onto a glass substrate by Sol–gel technique using dip coating method. The films were annealed at different annealing temperatures (400–500 °C) for 1 h. The structural, optical and electrical properties of the films were investigated and compared using X-ray Diffraction, UV–visible spectrophotometer and 4-point probe method. Optical analysis by mean transmittance T(λ) and absorption A(λ) measurements in the wavelength range between 300 to 800 nm allow us to determine the indirect band gap energy. DRX analysis of our thin films of TiO₂:Cu shows that the intensities of the line characteristic of anatase phase increasing in function of the temperature.     

Influence of vacuum annealing on the structural and photoelectrochemical properties of nanocrystalline MoBi2S5 thin films

In the present paper we report structural, optical, morphological and electrical properties of thin films of MoBi₂S₅ prepared by facile self organized arrested precipitation technique (APT) from aqueous alkaline bath. X-ray diffraction study on thin films suggests orthorhombic and rhombohedral mixed phase structure. The samples are further annealed under vacuum at 373 and 473 K. The EDS pattern shows minor loss of sulphur upto 473 K. The optical absorption in visible region shows direct allowed transition with band gap variation over 1.2–1.1 eV. Post-heat treated samples exhibit n-type electrical conductivity. SEM images show uniform distribution of spherical grains with diameter ∼200 nm for as-synthesized MoBi₂S₅ thin film. The grain size increases with annealing temperature and morphology becomes more compact due to crystallization of thin film. The surface roughness deduced from AFM, was in the range of 1.29–1.92 nm. The MoBi₂S₅ thin films are employed for the fabrication of photoelectrochemical solar cells as all the samples exhibit strong absorption in visible to near IR region. Due to vacuum annealing it gives a significant enhancement of power conversion efficiency (η) upto 0.14% as compared to as-synthesized MoBi₂S₅ thin film.     

Structural, ferroelectric and optical properties of Bi2VO5.5 thin films deposited on platinized silicon {(100) Pt/TiO2/SiO2/Si} substrates

Bismuth vanadate (Bi₂VO_5.5, BVO) thin films have been deposited by a pulsed laser ablation technique on platinized silicon substrates. The surface morphology of the BVO thin films has been studied by atomic force microscopy (AFM). The optical properties of the BVO thin films were investigated using spectroscopic ellipsometric measurements in the 300–820 nm wavelength range. The refractive index (n), extinction coefficient (k) and thickness of the BVO thin films have been obtained by fitting the ellipsometric experimental data in a four-phase model (air/BVO_rough/BVO/Pt). The values of the optical constants n and k that were determined through multilayer analysis at 600 nm were 2.31 and 0.056, respectively. For fitting the ellipsometric data and to interpret the optical constants, the unknown dielectric function of the BVO films was constructed using a Lorentz model. The roughness of the films was modeled in the Brugmann effective medium approximation and the results were compared with the AFM observations. PACS 78.20.-e; 77.84.-s; 77.55.+f     

Electrical and optical properties of Ga doped zinc oxide thin films deposited at room temperature by continuous composition spread

Ga doped ZnO (GZO) thin films were deposited on glass substrates at room temperature by continuous composition spread (CCS) method. CCS is thin films growth method of various Ga_xZn_1−xO(GZO) thin film compositions on a substrate, and evaluating critical properties as a function position, which is directly related to material composition. Various compositions of Ga doped ZnO deposited at room temperature were explored to find excellent electrical and optical properties. Optimized GZO thin films with a low resistivity of 1.46 × 10⁻³ Ω cm and an average transmittance above 90% in the 550 nm wavelength region were able to be formed at an Ar pressure of 2.66 Pa and a room temperature. Also, optimized composition of the GZO thin film which had the lowest resistivity and high transmittance was found at 0.8 wt.% Ga₂O₃ doped in ZnO.     

Optical properties of selenium-tellurium nanostructured thin film grown by thermal evaporation

Se-Te nanostructured thin films were deposited on glass substrates in the presence of oxygen and argon by thermal evaporation. The properties of Se-Te thin films strongly depend on the deposition method. During the process used, the substrate is cooled to a temperature of 77 K employing liquid nitrogen. The nanostructured thin films of Se_100−xTe_x (where x=4, 8 and 16) are deposited on glass substrate. The surface morphology of the deposited films was investigated through Scanning Electron Microscopy (SEM). The typical size of these nanostructures is in the range 40-100 nm and the length is of the order of several micrometers. The optical parameters i.e. optical gap (E_g), absorption coefficient (α), and extinction coefficient (k) are calculated in the wavelength range 190-1100 nm. It was found that the optical band gap decreased from 3.4 to 2.9 eV when Te concentration was increased in the Se_100−xTe_x nanostructured thin films. The large bandgap may be attributed to the decrease in particle size which clearly exhibits a quantum size effect. XRD analysis was performed to confirm glassy nature of the nanostructured thin films.     

A study of structural, compositional and optical properties of spray-deposited non-stoichiometric (Zn,Fe)S thin films

Non-stoichiometric ternary chalcogenides (Zn,Fe)S were prepared in the film form by pyrolytic spray deposition technique, using air/nitrogen as the carrier gas. The precursor solution comprised of ZnCl₂, FeCl₂ and thiourea. The depositions were carried out under optimum conditions of experimental parameters viz. carrier gas (air/nitrogen) flow rate, concentration of precursor constituents, nozzle substrate distance and temperature of quartz substrate. The deposited thin films were later sintered in argon at 1073 K for 120 min.The structural, compositional and optical properties of the sintered thin films were studied. X-ray diffraction studies of the thin films indicated the presence of (Zn,Fe)S solid solution with prominent cubic sphalerite phase while surface morphology as determined by scanning electron microscopy (SEM) revealed a granular structure.The chemical composition of the resulting thin films as analyzed by energy dispersive X-ray analysis (EDAX) reflected the composition of the precursor solutions from which the depositions were carried out with Fe at% values ranging from 0.4 up to 33.SEM micrographs of thin films reveal that the grain sizes of the thin films prepared using air as carrier gas and N₂ as carrier gas are in the vicinity of 300 and 150 nm, respectively.The diffuse transmittance measurements for thin films, as a function of wavelength reveal the dependence of direct optical band gap on Fe content and type of phase.     

Optical constants of thermally evaporated As10Te10S80 thin films

10 Te₁₀S₈₀ thin films were measured over the wavelength range 300 to 900 nm. A simple method, suggested by Swanepoel, was used for the determination of the optical constants and thickness of the film. The absorption edge is described using the non-direct transition model proposed by Tauc. The effect of one hour’s thermal annealing in the temperatures range 300–475 K on the optical properties of the As₁₀Te₁₀S₈₀ film is reported and explained. Received: 12 May 1997/Accepted: 1 August 1997