利用交叉相位调制和四波混频制作的时间透镜的仿真分析

利用高非线性光纤中的交叉相位调制和四波混频分别在仿真中实现了时间透镜. 对基于交叉相位调制的时间透镜中的高非线性光纤中的非线性过程进行了仿真分析. 仿真结果表明, 该时间透镜的主要影响因素为色散、自相位调制与四波混频; 通过采用带有一定色散斜率的高非线性光纤可同时消除色散、自相位调制和四波混频的影响; 另外, 该高非线性光纤的色散零点最好选在信号脉冲和抽运脉冲波长的中心附近. 然后对基于四波混频的时间透镜的实现进行了仿真分析. 仿真结果表明, 该时间透镜的主要影响因素为色散、 自相位调制和其他的四波混频; 通过设定合适大小的信号脉冲和抽运脉冲的功率可消除自相位调制和其他的四波混频的影响; 另外, 通过在高非线性光纤中引入一定的色散可进一步提高信号脉冲和抽运脉冲的功率, 从而获得更高功率的输出脉冲. 最后对两种时间透镜系统做出了比较. 关键词： 光脉冲压缩 时间透镜 交叉相位调制 四波混频     

Large-signal results for degenerate four-wave mixing and phase conjugate resonators

A numerical calculation procedure and various large-signal numerical solutions are presented for degenerate four-wave mixing in optical Kerr media, and for phase conjugate resonators using degenerate four-wave mixing. The solutions presented take full account of nonlinear refractive index changes, pump depletion, signal saturation, distributed losses, and possible external mirrors with laser gain. We find that including the nonlinear index change generally causes little change in the reflectivity or power output of degenerate four-wave mixing devices, at least with symmetric pumping. The optimum power output from a phase conjugate resonator with and without a laser gain medium is calculated. The results provide some theoretical guidance for designing phase conjugate resonators.     

Four-wave mixing crosstalk in optical fibre parametric amplifiers with orthogonal pumps

We experimentally investigated the generation of new unwanted frequencies generated by four-wave-mixing in fibre optical parametric amplifiers with two orthogonally polarised pumps and 17 dB of small signal gain. At these gain levels, we simultaneously observe two distinct types of mixing interactions and demonstrate that they vary with changing output power and gain at different rates. We also demonstrate that a combination of high pump power and low nonlinearity fibre results in less power in the unwanted peaks than a combination of low pump power and highly nonlinear fibre. Because these new unwanted four-wave mixing peaks result in crosstalk between wavelength division multiplexed channels, building parametric amplifiers with a combination of high pump power and fibre of low nonlinearity is desirable.     

Characteristics of a cw monolithic optical parametric oscillator

4 as a nonlinear crystal and obtained a pump threshold of 7 mW and an output power of 6 mW for a pump power of 40 mW. The OPO operated in a single longitudinal mode pair of a signal and an idler, over 1 h without mode hopping in the free-running condition. The signal and the idler wavelengths were tunable by 1 nm by changing the crystal temperature by 20 °C. The continuous tuning of the beat frequency between the signal and the idler was achieved by temperature tuning (slow control, 80 MHz/K) and E-field tuning (fast control, 0.75 MHz/V). We demonstrated the feasibility of frequency control by phase locking the beat frequency. The beat frequency could be successfully phase locked to a signal generated by a synthesizer through the electrooptic effect of the crystal. The phase locking could be maintained over 1 h. Received: 27 January 1998/Revised version: 9 March 1998     

Quantum cascade structure for mid-IR four-wave mixing

The design and modeling of a quantum cascade optical amplifier (QCOA) using intra-cavity non-linear interactions to achieve wavelength conversion is proposed. The model is based on the nonlinear equation coupled with Maxwell wave equations for different emission modes. In the proposed structure, four wave mixing (FWM) output exhibits a peak as a function of pump and probe frequency if they are tuned to the energy levels of the QC structure subbands. Results demonstrate that the FWM output signal power significantly depends on how subbands are engineered and interact with optical pulses which propagate in multi layer medium. In addition, we show that by adjusting pump and probe signal frequencies, FWM output power can be tuned.     

Noise squeezing in a nanomechanical Duffing resonator

We study mechanical amplification and noise squeezing in a nonlinear nanomechanical resonator driven by an intense pump near its dynamical bifurcation point, namely, the onset of Duffing bistability. Phase sensitive amplification is achieved by a homodyne detection scheme, where the displacement detector's output, which has a correlated spectrum around the pump frequency, is down-converted by mixing with a local oscillator operating at the pump frequency with an adjustable phase. The down-converted signal at the mixer's output could be either amplified or deamplified, yielding noise squeezing, depending on the local oscillator phase.     

窄线宽纳秒脉冲光纤拉曼放大器的理论模型和数值分析

窄线宽纳秒脉冲光纤拉曼放大器在非线性频率变换、遥感探测和量子信息等领域有广泛的应用前景.综合考虑受激拉曼散射(stimulated Raman scattering,SRS)、受激布里渊散射(stimulated Brillouin scattering,SBS)、自相位调制(self-phase modulation)和交叉相位调制(cross-phase modulation)等非线性效应,建立了窄线宽纳秒脉冲光纤拉曼放大器的非线性动力学模型.仿真分析了放大器中脉冲激光的时频演化特性,对比研究了抽运脉冲宽度、光纤长度和信号光功率等因素对放大器性能的影响.研究发现,上述因素会影响放大器的SRS阈值、SBS阈值、输出激光线宽、激光转换效率等.例如,当脉冲宽度为800 ns时,SBS随着抽运功率的增加而发生,限制了激光功率的提升;减短抽运脉宽可以抑制SBS,但是输出激光的线宽易于展宽到数百MHz以上;增加光纤长度可以获得更低的SRS阈值和更高的转换效率,但是SBS效应和光谱展宽程度也随之增强.系统搭建中需要平衡各非线性效应,选择合适的系统参数.研究内容可以为窄线宽纳秒脉冲光纤拉曼放大器的设计搭建提供参考.     

掺铒光纤非线性耦合器的实验研究

提出一种耦合参量可用光调控的掺铒光纤非线性耦合器.用熔融拉锥法熔合两根掺铒光纤,拉制成工作波长为155nm的3dB掺铒光纤耦合器.通过调变输入耦合器一臂的980nm泵浦光功率,可以改变两臂的传播常量差,从而改变耦合器两臂信号光的相对输出功率.通过测量输入泵浦光功率和两臂信号光输出功率,得到直通臂耦合比依赖于泵浦光功率的实验曲线.实验研究表明,当泵浦光功率从0 mW变化至20 mW时,耦合比的变化可达到40％.与理论模拟的结果一致.     

Numerical analysis of polarization character in Yb~(3+)-doped fiber amplifiers

Polarization-dependent gain (PDG) and state of polarization (SOP) of the output signal light in Yb3+-doped fiber amplifiers are studied by numerically stimulation, which showed that PDG of output signal light is not only changed with the input pump power and signal power, input polarization of pump and signal light, but also changed with the doping concentration, the cross-section anisotropy, the fiber length, the phase difference of the fiber, and so on. Moreover, SOP of the output signal light is studied. It is found that the polarization of output signal light is relative not only to the phase difference of the fiber, polarization of pump and signal light as the non-doped fiber, but also to PDG of output signal light, the cross-section anisotropy, the doping concentration, and so on, which is different to the non-doped fiber.     

大信号增益区的宽带OPCPA系统特性分析

 利用大啁啾信号光脉冲的光谱在时域内的分布特点，采用四阶龙格-库塔算法对宽光谱的光参量啁啾脉冲放大（OPCPA）激光器特性进行了数值分析。以LBO晶体为增益介质，信号光脉冲宽度取100 ps、啁啾系数为1 000，中心波长为800 nm；泵浦光的中心波长为532 nm，脉宽为100 ps。数值计算结果表明：信号光的非线性相位变化的中心部分为线性分布区，且随增益饱和的程度增大而增大；系统的功率转换效率有准振荡结构，且其第一个极值点为系统能量最大的转换率点；随着系统进入增益饱和区，压缩光脉冲的对比度明显降低，预脉冲长度显著增大。     

Phase noise generation in an amplitude limiter using saturation of a fiber-optic parametric amplifier

Generation of phase noise in an amplitude limiter using saturation of a fiber-optic parametric amplifier is analyzed. The analysis is based on the coupled differential equations for the amplitudes and phases of pump, signal, and idler involved in the four-wave mixing interaction. The equations are linearized about small fluctuations at operation points and are solved, which results in relations between the input and output phase and amplitude noise. These relations are used in deriving expressions of amplitude signal-to-noise ratio (SNR) and variance of phase noise of the output signal in terms of SNRs of input signal and pump. It is shown that optimum pump power exists for minimum output phase noise in the output signal.     

Kerr nonlinear switch based on ultra-compact photonic crystal directional coupler

In this paper, an all optical switch based on nonlinear photonic crystal directional coupler has been simulated and analyzed by the finite difference time domain (FDTD) method. The lunched pump signal increases the refractive indices of the central row of the coupler, due to nonlinear Kerr effect, hence the coupler works in the nonlinear conditions and lightwave guides to the other output port. We have tried to increase the coupling efficiency and reduce the required power in the nonlinear status by optimizing the bends structure and increasing the interaction between dielectric and lightwave signal. Therefore, the input signal beam can be controlled to be exchanged between two output ports to earn the highest output power ratio and the smallest amount of power required for nonlinear performance, the physical length of the coupler is determined to be 20a, where a is the structure lattice constant.     

Intra-cavity power effects in singly resonant cw OPOs

A continuous wave singly resonant optical parametric oscillator (cw SRO) has been developed that can be pumped at a level of up to 15 times its oscillation threshold by a single frequency fiber laser pump source. We report the observation of extremely high intra-cavity circulating powers of over 1 kW at the signal wavelength, and associated effects including heating of the nonlinear crystal, and beam quality degradation. Furthermore we show that these effects may be mitigated by implementing output coupling, while also extracting multi-Watt single frequency power output at both signal and idler wavelengths. PACS 42.65.Yj; 42.55.Wd; 42.62.Fi     

Interferometric output coupling of ring optical oscillators

We demonstrate the successful deployment of an antiresonant ring (ARR) interferometer within a ring optical resonator and its use for absolute optimization of output power. The integration of the ARR interferometer in a folded arm of the ring oscillator provides continuously variable output coupling over broad spectral range and under any operating conditions. We demonstrate the technique using a picosecond optical parametric oscillator (OPO), where we show continuously adjustable output coupling and optimization of the output power for different pump power conditions, from 3.5 W to 13.5 W. By operating the OPO under an optimized output coupling at 14 W of pump power, we obtain >5 W of extracted signal power, more than 2.6 times that with a ~5% conventional output coupler. We also show that the inclusion of the ARR interferometer has no detrimental effect on the spatial, temporal, and spectral characteristics of OPO output.     

The on-off contrast in an all optical switch based on stimulated Raman scattering in optical fibers

We present the investigation of the ON-OFF contrast in an optical switch using stimulated Raman Scattering in optical fibers. The setup consists of a Raman circuit of two fiber stages connected in series with a spectral filter rejecting the signal inserted between them. The stage 1 works as saturated amplifier, in this stage the pump pulses are saturated when pump and signal are launched to the input or travel through the fiber without saturation when pump only is launched at the input. The stage 2 works as a Raman amplifier with amplification depending on the pump power entering from the first stage. When pump only is launched at the input enter to the second stage without saturation and amplifies the signal entering this stage, strong signal pulses appear at the output; when pump and signal are launched to the input the pump is saturated in the first stage and the filter rejected the amplified signal, so that only low power pump enters the second stage and no signal pulses appear at the output. We use 2 ns pump pulses at 1528 nm and continuous-wave signal at 1620 nm. In the first stage of Raman circuit, we use both fibers with normal and anomalous dispersion. In fibers with anomalous dispersion, pump saturation is affected by modulation instability. We find that the contrast may be improved using fibers with normal and anomalous dispersion connected in series in the first stage, provided there is appropriate selection of their lengths. The best achieved contrast was 15 dB at 6 W pump peak power.     

All-Fiber Ultra-Fast Switching Using Stimulated Raman Scattering

We propose a method for all-fiber ultra-fast switching using stimulated Raman scattering. It is based on the transference of energy from the signal as pump to the control signal as first Stokes by stimulated Raman scattering. In the absence of a control signal, the transference of energy from the pump signal to the generated first Stokes is negligible, which results in high output power at the pump signal wavelength. To minimize the walk-off problem between two wavelengths, we chose pump signal and control signal to be equally spaced on opposite sides of the zero dispersion wavelength of the fiber. Based on this assumption, the all-fiber ultra-fast optical switch with low power consumption and high output extinction ratio can be realized.     

非临界相位匹配RTP晶体1.6μm光参量振荡器

采用非临界相位匹配切割,尺寸4mm×4mm×20mm的磷酸钛氧铷(RTP)晶体作为非线性光学晶体,进行了半导体激光端面抽运Nd:YAG/RTP的内腔式光参量振荡获得人眼安全激光的实验研究。对比了不同声光调Q重复频率下的信号光输出特性。在10.5W的抽运功率和15kHz的重复频率下,获得了最高900mW的1.62μm人眼安全激光输出,光光转换效率达8.6%。1.62μm信号光和对应的1.06μm基频光的脉冲宽度分别为4.6和8.2ns。信号光中心波长在1618nm,谱线宽度小于0.5nm。     

LD端面抽运Nd:YLF/KTA连续光参量振荡激光

采用非临界相位匹配切割,尺寸5mm×5mm×20mm的KTA作为非线性光学晶体,进行了基于半导体激光端面抽运Nd:YLF/KTA的内腔式连续光学参量振荡激光研究,获得了中红外3.5μm波段的连续激光输出。为了提高连续光参量振荡腔内信号光的功率密度,降低激光输出阈值,采用对信号光高反射的单谐振腔结构进行激光实验。在8.35W的抽运功率下,分别获得了335mW和110mW的3440nm和1505nm的激光输出,对应的总转换效率达到了5.6%。该实验研究表明半导体激光端面抽运的内腔式KTA连续光学参量振荡也能获得高效的中红外激光输出。     

Nonlinear repolarization in optical fibers: polarization attraction with copropagating beams

We propose a type of lossless nonlinear polarizer, novel to our knowledge, a device that transforms any input state of polarization (SOP) of a signal beam into one and the same well-defined SOP toward the output, and perform this without any polarization-dependent losses. At the polarizer output end, the signal SOP appears to be locked to the input pump SOP. The polarizer is based on the nonlinear Kerr interaction of copropagating signal and pump beams in a telecom or randomly birefringent optical fiber.     

Stimulated Brillouin scattering limited intensity-dependent four-wave mixing between pump and signal in a non-zero dispersion shifted fiber

The intensity-dependent four-wave mixing (FWM) efficiency is derived by the nonlinear Schrodinger equations including the self phase modulation and cross phase modulation between the two Fabry–Perot modes of a pump and a single-wavelength signal. The maximum FWM for mixing the pump with signal in non-zero dispersion shifted fiber is explained as the minimum phase mismatch for FWM due to equal group delay for the pump and signal. It was also found that the experimental measurements for the generated FWM power are limited by the stimulated Brillouin scattering (SBS) threshold. Under the SBS threshold, the experimental results are still coincided well with the theoretical calculations of the FWM generated power ratio to have the difference of 0.12 dB for the input signal power of 12 mW.