甘氨酸燃烧合成YAG∶Tb荧光粉的微观结构和发光特性

Luminescent terbium doped yttrium aluminum garnet (YAG∶Tb) powders were prepared using yttrium and aluminum oxide precursor particles produced by combustion process with glycine. Heat treatment of the resulting precursor powders at 950℃ or 1450℃ for 2h, yielded pure YAG particles. The morphology of YAG∶Yb phosphor after sintering at 1450℃ appeared to be spherical or elliptical and the grain size of the phosphor was in the range of 0.6 to 1.4μm. From the photoluminescence spectra, transitions ⁵D₄- ⁷F_J corresponding to Tb³⁺ in YAG matrices were identified. The prominent transition ⁵D₄- ⁷F₆ emission for YAG∶0.05Tb phosphor after sintering at 1450℃ was very significant to improve the chromaticity of YAG∶Tb phosphor.     

助熔剂法制备的LaMgAl11O19∶Eun+(n=2，3)的发光特性

LaMgAl₁₁O₁₉∶Euⁿ⁺(n=2,3) was synthesized by solid state reaction using H₃BO₃ as a flux at 1 400 ℃ for 4 hours. And their luminescent properties was investigated under UV and VUV excitation. Strong pure blue emission due to d-f transition of Eu²⁺ was observed in LaMgAl₁₁O₁₉∶Eu²⁺ both in 254 nm and 147 nm excitation. At the same time, red emission due to ⁵D₀ → ⁷F_J (J=0, 1, 2, 3, 4) transition of Eu³⁺ also observed in LaMgAl₁₁O₁₉∶Eu³⁺. The dependence of emission intensity of blue/red emission on Eu²⁺ / Eu³⁺-content was evaluated. The result indicated that the blue emission intensity was arrived optimum when Eu²⁺-content was 0.10 mol·mol^-1under both UV and VUV excitation while red emission intensity reached optimum when Eu³⁺-content was 0.125 mol·mol^-1 under UV excitation. This suggests that LaMgAl₁₁O₁₉∶Eu²⁺ phosphors could be potential blue phosphor for the application in PDP.     

球形La2O3∶Eu纳米晶的制备及其发光特性

The spheric La₂O₃∶Eu nanocrystals were prepared using NH₃·H₂O-NH₄HCO₃ mixture as precipitant. The material was characterized by FTIR, XRD and TEM techniques. The luminescence properties of Eu³⁺ in spheric La₂O₃ were measured by three dimension spectra, emission and excitation spectra. The results indicate that the La₂O₃∶Eu nanocrystals are in hexagonal phase by annealing at 800 ℃, the crystal size is about 30 nm. The maximum emission and excitation wavelength were determined by three dimensional spectroscopy to be at 591 nm and 394 nm, respectively. In emission spectrum the band at 591 nm and 612 nm are corresponding to ⁵D₀-⁷F₁ and ⁵D₀-⁷F₂ transition of Eu³⁺ ions. With increasing in annealing temperature the differences of intensity of the two transitions are increased. This phenomenon shows that the luminescence intensity of La₂O₃∶Eu nanocrystals can be tuned by changing annealing temperature.     

Eu3+在La2O2S中的长余辉发光

The new Eu³⁺ doped lanthanum oxysulfide phosphors,which have the orange-red long afterg low emission,were synthesized by solid-state reaction method.The synthesized phosphors were characterized by X-ray diffraction.The excitation and emission spectra,afterglow spectra and afterglow decay curves were examined.XRD confirmed the phosphor as pure phase La₂O₂S.The phosphors showed typical transitions ⁵D_J(J=0,1) → ⁷J_J(J=0,1,2,3,4)of Eu³⁺.The photoluminescence spectra and afterglow spectra presented the regular alteration with various Eu³⁺ concentration, due to cross relaxation between energy levels of Eu³⁺. In addition, we studied the effects of activator concentration and dopants species on the afterglow property. The data showed afterglow result was the best with 2 % Eu³⁺ and doped with Mg²⁺ and Zr⁴⁺. A prominent phosphorescence can be seen in this phosphor after illuminated with UV light.     

稀土红色荧光粉SrZnO2∶Eu3+的发光性能

A series of novel luminescent materials, SrZnO₂∶M (M=Eu³⁺, or Eu³⁺ + Li⁺) have been synthesized by high-temperature solid-state reaction. The structure and luminescence properties of SrZnO₂∶Eu³⁺ phosphor were studied through XRD, photoluminescence and Raman spectroscopy. The excitation spectra show a broad intense band and a number of small peaks corresponding to the inner 4f-shell excitations of Eu³⁺ (the strongest one is at 395 nm for ⁷F₀-⁵L₆). After SrZnO₂∶Eu³⁺ phosphor was co-doped with Li⁺ ions, its charge transfer band extended to longer wavelengths. This resulted in increase of luminescent quantum efficiency of the sample. SrZnO₂∶Eu³⁺,Li⁺ phosphor can be efficiently excited by longer UV. From the fluorescence spectrum of SrZnO₂∶Eu³⁺ phosphor, apart from transition emissions of ⁵D₀→ ⁷F_J (J=0～4), the transition emissions from ⁵D₁ → ⁷F_J (J=0～2) have been observed. For the SrZnO₂∶Eu³⁺ phosphor, under excitation of UV, the dominant emission is at about 612 nm, due to the ⁵D₀→ ⁷F₂ hypersensitive transition. The incorporation of Li⁺ ions greatly enhanced the luminescence intensity and made emission peak from ⁵D₀ → ⁷F₂ transition red-shifted.     

Si5P6O25∶Tb3+的结构与荧光性质

Tb³⁺ ions were incorporated in P-Si matrix material through a sol-gel process. Luminescence properties of Tb³⁺ as a function of dopant， firing temperature， composition and structure of matrices were investigated. The gels synthesized by the reaction of P₂O₅ or H₃PO₄ with tetraethoxy silane and TbCl₃ as dopant were fired in air from the temperature 25～1000℃ to form P-Si crystalline phase. The crystal structure was determined by powder X-ray diffraction. Si₅O(PO₄)₆ were the only crystalline phase and belong to hexagonal crystal system. The emission of ⁵D₄-⁷F₅(～545nm) transition of Tb³⁺ in the P-Si system is composed of two peaks. The amount of doping Tb³⁺ varied from 0.664% to 1.644%， and no obvious concentration quenching was observed in this doping concentra-tion range. The intensity of Tb³⁺ emission increased with firing temperature increasing and becomes stable at 800～1000℃.     

Eu3+掺杂SiO2-B2O3-NaF玻璃的制备及发光性质

The Eu-doped SiO₂-B₂O₃-NaF glass was prepared by sol-gel process, using tetraethoxy Silicane, boric acid and sodium fluoride as starting materials, 0.10 mol·L^-1 EuCl₃ solution as the dopant. The luminescent properties of Eu³⁺ doped SiO₂-B₂O₃-NaF phosphors were investigated. The phosphors showed prominent luminescence in pink, the strong emission of Eu³⁺ comes from electronic transition of ⁵D₀- ⁷F₁（591 nm）and ⁵D₀- ⁷F₂（615 nm）,which derived from two transition modes of magnetic-dipole and electric-dipole .The peak intensity of 591nm in SiO₂-B₂O₃-NaF matrix is much stronger than it in the other matrixes, it means that SiO₂-B₂O₃-NaF has sensitization on the transition of ⁵D₀- ⁷F₁ (Eu³⁺). If there are broad bonds in the range of 275～380 nm in the excitation spectrum of Eu³⁺ -doped SiO₂-B₂O₃-NaF glass, the emission peak intensity should be intensified. It is because the electron migration CT band of O^2--Eu³⁺. For all Eu³⁺ concentrations used, the investigation found that when the mass of fraction got to 29.19×10^-3, the luminescence intensity reached the summit. And there is a phenomenon of concentration quenching. Investigation with the same concentration of Eu³⁺ at different annealed temperature, we found that the sample annealed at 400 ℃, the luminescence intensity achieved its maximum value, and Eu³⁺ in this matrix had a phenomenon of temperature quenching. The structural characterization of these luminescent materials was carried by used XRD and TEM. The result showed that the phosphor was in amorphous phase.     

沉淀法合成纳米晶长余辉材料Y2O2S∶Eu3+，Ti

The long-lasting phosphorescent materials, yttrium oxysulfides doped by Eu and Ti, were systhesized by coprecipitation with their subsequent thermal decomposition in the presence of sulphur. The products were characterized by XRD, TEM, phosphorescent spectra, and thermoluminescence. The XRD results indicate that the lowest synthesis temperature is 700 ℃. From the TEM, the average diameter of particles was in the range of 60～120 nm, and augmented with the increase of temperature. The materials under UV excitation presented well afterglow from the transition of ⁵D_0,1 → ⁷F_J of Eu³⁺, and the persistent time was about 2 h. The long-lasting afterglow mechanism was discussed, too.     

Ce0.8Y0.2O1.9-Ca3(PO4)2-K3PO4复合电解质在中温区的质子导电性及在常压合成氨中的应用

A precursor of Ce_0.8Y_0.2O_1.9(YDC) solid electrolyte was synthesized by the gol-gel method. YDC and phosphates powders were prepared by mixing the YDC and phosphates according to different weight ratios. The mixtures of the YDC and binary phosphates were ground and sintered at 1 400 ℃. The proton conductivity in solid electrolyte of the sintered samples was examined using electrochemical methods at 400～800 ℃. Ammonia was synthesized from nitrogen and hydrogen at atmospheric pressure in the solid state proton conducting cell reactor. The optimal condition for the ammonia production was determined. The result indicated that composite electrolyte of 80wt% YDC: 20wt% binary phosphates as proton conductor could obtain the highest ionic conductivity and ammonia production rate among the four samples, the rate of evolution of ammonia was up to 9.5 × 10^-9 mol·s^-1·cm^-2.     

ZrWO4F2的前驱物法合成和表征

Zirconium tungsten oxyfluoride, ZrWO₄F₂, was firstly synthesized with the precursor route. The composition of the compound was determined by combining the results of ICP and XPS. The indexed powder X-ray diffraction pattern of this compound indicates that it is a pure phase, orthorhombic crystal system, space group D₂²=P2₁22 and a=15.32(2)?,b=13.877(7)?,c=8.42(2)?.Combining the results of the DTA-TGA curves from room temperature to 700℃ and XRD patterns in different temperatures the mechanism was revealed during the solid precursor (1) been heated to 700℃. The zirconium tungsten oxyfluoride was considered to be a metastable com-pound. The ascertaining of annealing time and temperature is the key of handling.     

Die Kristallstruktur des W3CoB3 und der dazu isotypen Phasen Mo3CoB3, Mo3NiB3 und W3NiB3

Zusammenfassung Mo₃CoB₃, Mo₃NiB₃, W₃CoB₃ und W₃NiB₃ kristallisieren in einem eigenen Typ (W₃CoB₃-Struktur). Das trigonal prismatische Bauelement [T ₆B]^* ist zu Ketten vereinigt, wobei B₃-Gruppen entstehen. Die Phasen sind vermutlich Bor-reicher als obiger Formel entspricht.

---

The crystal structure of W₃CoB₃ and the isotypic phases Mo₃CoB₃, Mo₃NiB₃, and W₃NiB₃

Mo₃CoB₃, Mo₃NiB₃, W₃CoB₃, and W₃NiB₃ were found to possess a new type of crystal structure (W₃CoB₃-structure type). Trigonal prismatic groups [T ₆B]^* are linked together forming chains in such a way that B₃-groups occur. These borides do probably exist with a larger amount of boron as to compared with the formula.

---

---

Mit 2 Abbildungen     

γ-Nitro-γ-butyrolacton

γ-Nitro-γ-butyrolactone By oxidation of 3-(1-nitro-2-oxocyclohexyl)propanal ( 1 ) with KMnO₄, besides 3-(1′-nitro-2′-oxocyclohexyl)pripionic acid ( 2 ), the complete hydrolysis product 4-oxononanedioic acid ( 4 ) and the oxidized semi-hydrolysis product 5-(2-nitro-5-oxotetrahydro-2-furyl)pentanoic acid ( 3 ) were formed. The crystalline 3 decomposes at r.t. forming 4 and nitrous gases; its structure was established by X-ray determination.     

Synthesis of γγγ-trifluorocarbonyl compounds

γγγ-Trifluorocarbonyl compounds are easily obtained in a good yield by introduction of the 1,1,1-trifluoroethyl moiety (CF₃-CH₂-) on the -methylene group of a ketone.     

K3SbSe3, Rb3SbSe3 und Cs3SbSe3 – Synthese und Kristallstruktur

K₃SbSe₃, Rb₃SbSe₃, and Cs₃SbSe₃ – Synthesis and Crystal Structure The compounds K₃SbSe₃, Rb₃SbSe₃ and Cs₃SbSe₃ were synthesized by heating mixtures of Sb₂O₃ and an alkalicarbonate in a stream of hydrogen saturated by selenium in a temperature range between 750 °C and 800 °C. The compounds crystallize isostructural with Na₃AsS₃. A comparison of atomic distances and bond angles with those of the isostructural arsenic and bismuth compounds shows the effect of lone pairs.     

Freezing the polarization of CH3NH3PbI3 and CH3NH3PbI3-xClx perovskite films

Thin films of methylammonium lead halides, CH₃NH₃PbI₃ and CH₃NH₃PbI_3-xCl_x, were deposited onto symmetrical microstructured electrode arrays of gold or platinum on Si/SiO₂ wafers. Polarization studies were carried out on perovskite films under vacuum in the dark. For poling, a constant voltage was applied to the samples while the temperature was cycled between 295 K and 4 K. The measured current densities depending on the temperature showed distinct characteristics relating strongly to the crystal phase and the dielectric properties of the perovskite films. Voltage sweeps were carried out at different scan rates at specific temperature intervals after poling. The polarization of the films due to the migration of iodide vacancies in direction of the blocking perovskite/metal interface was frozen almost up to room temperature. Charge carriers were only able to cross the blocking barrier and contribute to the current where the ions have accumulated during poling. All J-V curves showed hysteresis: inverted and regular hysteresis at room temperature and below, respectively. Inverted hysteresis originates from the slow accumulation of ions at the blocking barrier, while regular hysteresis arises from a distortion in the adjacent crystals which will be discussed.     

Synthesis of some derivatives of 3-amino-3-desoxyerythrose and 3-amino-3-desoxy-D-3-erythrose

The synthesis of derivatives of 3-amino-3-deoxy-L-erythrose by LAH or LAD reduction of the oxime of 1,2-O-isopropylidene α-L -glycero-tetros-3-ulofuranose is described.     

3x-pyrrolizin-3-ones

Condensation of pyrrole-2-dithiocarboxylates with CH acids containing ester groups, in the KOH-DMSO system, was used to prepare previously unknown 1-alkylthio-3H pyrrolizin-3-ones. The latter, treated with secondary amines, are readily converted to the corresponding 1-amino derivatives.     

3-H-pyrrolizin-3-ones

Previously unknown 1-alkylthio-3H-pyrrolizin-3-ones have been obtained by the condensation of pyrrole-2-dithiocarboxylates with CH acids containing ester groupings in the KOH-DMSO system. On treating the products with secondary amines they are readily converted into the corresponding 1-amino derivatives.Irkutsk Branch of the Russian Academy of Sciences, Irkutsk 664033. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 7, pp. 919–924, July, 1996. Original article submitted May 2, 1996.