微流动注射芯片化学发光法测定雨水中过氧化氢

基于luminolH2O2Co2+化学发光体系,设计了一种新的微流动注射芯片,准确测定了雨水中的H2O2含量。芯片由两块50mm×40mm×5mm的透明有机玻璃(PMMA)在实验室加工而成。由CO2激光雕刻机刻蚀出的微通道宽200μm,深150μm。方法的线性范围为0.05～2μmol/L;检出限为0.02μmol/L(S/N=3)。对0.6μmol/L的H2O2溶液平行测定9次,得方法的相对标准偏差(RSD)为4.6%。该方法已成功用于雨水中微量H2O2的测定。     

微分析系统对苯二酚抑制化学发光的研究

在自行设计和制作的有机玻璃 (PMMA)微流控芯片上 ,以流动注射方式进样 ,利用对苯二酚对Luminol H2 O2 Co2 +体系化学发光 (CL)的强抑制作用 ,建立了间接测定对苯二酚含量的微型全化学分析系统 ( μ TAS)。对影响化学发光反应的各因素进行优化 ,对芯片结构的设计和反应过程进行探讨 ,设计并制作出适合该反应体系的芯片。在合成水样对苯二酚的测定中 ,化学发光强度的变化与对苯二酚的浓度在 1 .0× 1 0 - 7～ 2 .0× 1 0 - 8mol/L范围内成良好线性关系 ,检出限达 2 .0× 1 0 - 9mol/L。     

流动注射化学发光增强法测定单宁酸

发现单宁酸对Luminol KIO4 Mn2 +碱性体系的化学发光有较强增敏作用 ,据此建立了流动注射化学发光增强法测定单宁酸的新方法。该法简单、快速、线性范围宽 ,测定单宁酸的检出限为 9× 10 -9mol/L ;线性范围为 3× 10 -8～ 5× 10 -6mol/L ,对于 1× 10 -6mol/L单宁酸测定的相对标准偏差 1 5 % (n =11)。应用于五倍子中单宁酸的测定 ,结果满意。     

四磺基锰酞菁作为过氧化物模拟酶在过氧化氢化学发光测定中的应用

以四磺基锰酞菁 (MnTSPc)作为过氧化物模拟酶催化H2 O2 与鲁米诺的化学发光反应 ,建立了测定环境样品中H2 O2 的化学发光分析新方法。该法的线性范围为 4 .0× 10 - 8～ 2 .0× 10 - 5mol L ;检出限为 6 .8×10 - 9mol L ;对 1.0× 10 - 6 mol L的H2 O2 进行连续 10次平行测定 ,相对标准偏差为 2 .4 %。用本法对天然雨水进行了分析测定 ,结果良好。     

化学发光法测定氧氟沙星的含量

利用氧氟沙星对碱性Luminol H2O2 化学发光体系的增敏作用,建立了一种测定氧氟沙星的新方法。方法的线性范围为5.53×10-9 ~2.21×10-5 mol/L,检出限(3σ)为5.08×10-10 mol/L,RSD为2.23%(cs=1.38×10-5 mol/L,n=8)。该法用于针剂、片剂及胶囊中氧氟沙星含量的测定,结果令人满意。     

无机流动相低压离子色谱分离-化学发光在线检测痕量锰

以0.09 mol/L KCl和0.01 mol/L HCl的混合溶液作流动相,低压离子色谱(LPIC)分离,鲁米诺-H2O2化学发光(CL)在线检测Mn2+。研究了分离条件、化学发光条件及二者匹配方式和干扰离子等因素对分离和检测的影响。测定Mn2+的线性范围为1×10-9~4×10-8g/L,检出限为1×10-9g/L。该法用于测定血清、尿液、嘉陵江水样中的Mn2+。     

流动注射邻菲啰啉化学发光体系测定羟自由基

利用Vitc-CuSO4-H2O2产生的羟自由基,建立流动注射邻菲口罗啉化学发光体系测定羟自由基的产生及物质对羟自由基的清除能力。体系中各种物质浓度的最佳组合是:邻菲口罗啉1.0×10-3mol/L(pH 8.2硼砂-硼酸缓冲液配制、内含CTMAB浓度为5.0×10-3mol/L)、Cu2+1.5×10-3mol/L、H2O2体积分数0.6%、抗坏血酸1.5×10-3mol/L。硫脲清除羟自由基的量效关系Y=25.0009ln(x)+65.3120,r=0.9988,IC50=0.542 mmol/L。龙井茶水提液对羟自由基具有较强的清除作用。     

流动注射化学发光增强法测定巯嘌呤的应用研究

试验发现6-巯基嘌呤对Luminol-H2O2-OH-体系的化学发光有较强的增敏作用。据此建立了一种流动注射化学发光增强法测定6-巯基嘌呤的新方法。该法测定6-巯基嘌呤的检出限为7.5×10-9mol/L,线性范围为2.0×10-8~2.5×10-6mol/L,对6.0×10-7mol/L的6-巯基嘌呤测定的相对标准偏差为1.6%(n=11),已用于合成样中6-巯基嘌呤的测定。     

锰(Ⅳ)-安乃近-甲醛化学发光体系的研究

实验发现锰(Ⅳ)氧化安乃近可以产生弱的化学发光,甲醛对这一化学发光反应有较强的增敏作用。据此建立了测定安乃近的流动注射化学发光分析法。在最优化的条件下,测定安乃近的线性范围为6 0×10-7～1 0×10-5mol/L,检出限为2×10-7mol/L安乃近。对1.0×10-6mol/L安乃近进行11次测定,相对标准偏差为3.4%。该方法已应用于针剂中安乃近的测定,其结果与药典方法测得值一致。     

流动注射化学发光法测定稀土矿中三价铽

NaIO4H2O2是弱的化学发光体系,而Tb3+与EDTA形成的络合物对NaIO4H2O2的化学发光有显著的增敏作用,而且Tb3+EDTANaIO4H2O2体系的相对发光强度与Tb3+浓度成正比,在选定的最佳实验条件下,Tb3+的浓度与化学发光强度在1.0×10-7～1.0×10-5mol/L之间呈良好的线性关系;检出限为8.0×10-9mol/L;对浓度为1.0×10-6mol/L的Tb3+进行12次平行测定,相对标准偏差为3.2%。利用该方法成功的测定了矿样和稀土氧化物中的铽的含量。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.