红外光谱法研究重氮树脂自组装膜的光化学反应

将具有导电功能的聚(4-羧酸钠苯基)乙炔阴离子(PCPA)与具有生物活性的DNA聚阴离子交替与重氮树脂聚阳离子(DR)进行自组装,可以得到层重复单元为DR／DNA／DR／PCPA的三夹层聚电解质自组装膜。重氮树脂聚阳离子在紫外光照射下可与聚阴离子发生光化学反应,使层与层之间的离子键连接转化为共价键连接,从而制备稳定的纳米级超薄膜。本文用红外光谱法对此类聚电解质自组装膜的光化学反应过程进行了研究。     

负载肝素及生物素化肝素修饰的纳米粒子的基质介导基因传递系统

首先通过静电作用将带负电荷的肝素及生物素化肝素和带正电荷的PAMAM/DNA自组装,分别制备了PAM AM/DNA/heparin和PAMA M/DNA/heparin-biotin复合物,然后用快速降解胆酸功能化星型聚(DL-丙交酯)作为基质、并加入水溶性高分子α,β-聚(N-2-羟乙基)-L-天冬酰胺(PHEA)作...     

聚谷氨酸为骨架的梳状基因载体的合成及生物学性能评价

以聚谷氨酸为骨架, 用低分子量聚乙烯亚胺胺解聚谷氨酸苄酯, 得到聚谷氨酸-g-聚乙烯亚胺, 用异佛尔酮二异氰酸酯将聚乙二醇单甲醚偶联到聚谷氨酸-g-聚乙烯亚胺上, 合成了梳状聚阳离子基因载体聚谷氨酸-g-(聚乙烯亚胺-b-聚乙二醇). 利用核磁共振氢谱、 激光粒度分析仪、 Zeta电位仪和凝胶电泳对聚阳离子载体及其与质粒脱氧核糖核酸(pDNA)形成的复合物进行了表征. 通过噻唑蓝(MTT)细胞毒性测试、 绿色荧光蛋白质粒pEGFP-C1及荧光素酶质粒pGL3体外转染实验考察了载体的细胞毒性及基因转染效率. 结果表明, 当聚乙烯亚胺中N原子和DNA中P原子的摩尔比(N/P)大于5时, 载体能很好地包裹DNA, 载体与DNA形成的复合物粒径约为130 nm, Zeta电位约为28 mV; 通过MTT实验和体外质粒转染实验显示出载体在测量范围内具有极低的细胞毒性和较高的转染效率.     

CMC-g-DNA接枝共聚物的合成与表征

在磷酸盐缓冲溶液中用1-(3-二甲氨基丙基)-3-乙基碳二亚胺(EDC)与N-羟基琥珀酰亚胺(NHS)活化羧甲基纤维素钠(CMC)侧链上的羧基; 在室温下再将活化的CMC与5'端经氨基修饰的单链脱氧核糖核酸(DNA)齐聚物(ODNs)反应, 获得CMC上接枝ODNs的共聚物(CMC-g-ODNs), 以Lambda DNA为模板, 通过聚合酶链式反应(PCR), 将接枝的ODNs扩增为长度为1300个碱基对的双链DNA, 从而制得CMC侧链上接枝DNA的共聚物CMC-g-DNA. 采用傅里叶红外光谱仪测定CMC与NHS形成的中间体; 用水平式琼脂糖凝胶电泳和垂直板变性聚丙烯酰胺凝胶电泳对CMC-g-DNA接枝共聚物进行表征. 结果表明, 合成了CMC-g-DNA接枝共聚物, 且在酸性条件下CMC的活化效果更好; 同时, 接枝在CMC上的DNA在琼脂糖凝胶电泳中迁移速率加快, 而在聚丙烯酰胺凝胶电泳中迁移速率减慢.     

DNA-树状聚脂肪醚杂化体的合成及组装性能研究

通过半固相合成方法得到一类新型的具柔性骨架的树状聚脂肪醚(PMDC)与DNA的嵌段共聚物, 也称为DNA-树状聚脂肪醚杂化体, 其结构通过了MALDI-TOF MS、HPLC和聚丙烯酰胺凝胶电泳(PAGE)表征. 研究证明, 通过调节DNA-树状聚脂肪醚杂化体的结构和组装的溶剂体系, 可以得到各种不同的有序聚集体(球形胶束、纳米纤维等), 这些组装形貌均通过透射电镜(TEM)、原子力显微镜(AFM)和动态光散射(DLS)进行表征; 荧光包裹实验和DNA互补配对实验不仅证明了疏水树状聚脂肪醚位于组装体内核、DNA处于外壳的组装机理, 也说明这类DNA-树状聚脂肪醚杂化体将在疏水药物运输和纳米技术等领域具有潜在的应用.     

adr亚型乙型肝炎病毒表面抗原基因在大肠杆菌中的表达

利用adr亚型乙型肝炎病毒(HBV)DNA克隆株,组建表面抗原(HBsAg)基因表达质粒。用竞争性抑制放射免疫分析方法和聚丙烯酰胺——SDS凝胶电泳检测表达产物,获得了含HBsAg的杂合多肽。     

PLL-PEG-PLL三嵌段共聚物的制备及DNA包覆应用

将PLL(Z)-PEG-PLL(Z)中的氨基去保护得到两端为聚阳离子的嵌段共聚物PLL-PEG- PLL, 并对与DNA结合形成的聚集体的性质进行了研究. 结果表明: PLL-PEG-PLL与DNA在水相中形成了聚离子复合物胶束; DNA与PLL通过静电作用形成核, PEG包裹在外面, 得到的聚离子复合物胶束为均一体系, 即使在化学计量点也不会沉淀, 保持着很好的流动性和稳定性, 这一点对基因治疗是很重要的; 而且随着PLL段的增加, 包覆效果更好; 聚离子复合物胶束使得DNA具有较强的核酶抗性; 大小在10~35 nm之间, 主要呈球形; 聚离子复合物胶束能够用于基因的传递, 使基因在细胞系SF9中表达出蛋白质.     

阳离子基因载体的pH敏感遮蔽体系的制备及表征

合成了一种pH敏感的遮蔽体系-谷氨酸苄酯/谷氨酸共聚物(PBLG-co-PGA), 用于对DNA/阳离子基因载体复合物颗粒表面正电荷的遮蔽, 以提高其在体内的稳定性. 研究表明, PBLG-co-PGA (PGA(x), x为PGA占共聚物中摩尔百分数)具有pH敏感性. 并以pH敏感点接近生理pH值的PGA(60)为遮蔽体系进行研究. PGA(60)能够对DNA/PEI(1:1)复合物颗粒表面正电荷进行有效遮蔽. 凝胶阻滞电泳显示, 用PGA(60)对DNA/PEI复合物进行不同比例遮蔽, 没有发生与DNA的链交换作用. MTT细胞毒性测试表明, PGA(60)和三元复合物DNA/PEI/PGA(60) 在测试范围内几乎没有细胞毒性. 荧光素酶转染实验表明, 部分遮蔽后转染效率有所提高; 用PGA(60)对DNA/PEI复合物完全遮蔽为负电后, 由于同细胞表面的电荷排斥作用, 三元复合物不易被细胞内吞, 导致不发生细胞转染. 因其合适的pH响应性, PGA(60)将可能成为一种能随pH值的变化, 实现对聚阳离子基因载体进行电荷遮蔽/智能释放的遮蔽材料.     

聚电解质结构及盐浓度对基于DNA和聚阳离子的层层组装型大孔薄膜结构的影响

选择2种不同类型的聚阳离子[强电解质型聚二烯丙基二甲基氯化铵(PDDA)和弱电解质型聚盐酸丙烯胺(PAH)], 分别和脱氧核糖核酸(DNA)分子通过静电吸附作用制备层层组装膜. 利用原子力显微镜和紫外-可见分光光度计研究了聚阳离子结构和组装分子溶液中盐(NaCl)浓度对大孔结构及薄膜生长规律的影响. 结果表明, 在DNA/PDDA体系中, 盐浓度对于大孔结构的形成起到关键性作用. 而对于DNA/PAH薄膜体系, 即使增加DNA或PAH溶液中盐的浓度, 也不会有大孔结构出现, 这主要是由PAH分子的弱电解质特性决定的.     

无标记DNA在氨基改性导电聚吡咯表面的固定/杂交

通过吡咯(Py)与其衍生物——6-吡咯己胺(PyHA)的共聚物聚(吡咯-co-6-吡咯己胺)[poly(Py-co-PyHA)]的合成研究,并采用电化学循环伏安法来考察体系的电化学活性.在缓冲溶液中,由于探针DNA链上的负电荷与共聚物分子链上的正电荷之间存在强烈的静电吸引力,使得DNA能够固定在导电聚合物膜上.实验结果证明,目标DNA和聚吡咯薄膜之间不存在非特异性吸附,而能和探针DNA进行顺利杂交.此结果为以后研究更为敏感的DNA固定及导电聚合物敏感膜提供了实验基础.     

Direct Electrochemistry of Hemoglobin in Layer‐by‐Layer Films Assembled with DNA and Room Temperature Ionic Liquid

Based on electrostatic interaction and electrodeposition, poly‐anionic deoxyribonucleic acid (DNA), room temperature ionic liquid 1‐butyl‐3‐methyl‐imidazolium tetrafluoroborate (BMIMBF₄), hemoglobin (Hb) and Poly(diallyldimethylammonium chloride) (PDDA) were successfully assembled into Hb/IL/DNA/PDDA layer‐by‐layer complex films on the surface of ITO electrode. FTIR spectroscopy, electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) were used to characterize the composite film. The obtained results demonstrated that the Hb molecule in the film kept its native structure and showed its good electrochemical behavior. A pair of well‐defined redox peaks of Hb with the formal potentials (E°′) of ?0.180 V (vs. SCE) was appeared in phosphate buffer solution (PBS, pH 7.0). The Hb/IL/DNA/PDDA/ITO modified electrode also showed an excellent electrocatalytic behavior to the reduction of hydrogen peroxide (H₂O₂). Therefore, the IL/DNA/PDDA complex film as a novel matrix open up a possibility for further study on the direct electrochemistry of other proteins and the fabrication of the third‐generation electrochemical biosensors.     

Adsorption and Electrooxidation of DNA at Glassy Carbon Electrodes Modified with Multiwall Carbon Nanotubes Dispersed in Glucose Oxidase

We are proposing for the first time the successful immobilization of DNA at glassy carbon electrodes (GCE) modified with carbon nanotubes (CNT) dispersed in glucose oxidase (GOx) (GCE/CNT‐GOx) either by direct adsorption or by layer‐by‐layer self‐assembling using polydiallyldimethylamine (PDDA). The presence of GOx allows an efficient dispersion of CNT and gives a most favorable environment that promotes the adsorption and makes possible a more sensitive electrooxidation of DNA. The PDDA incorporated in the self‐assembled architecture largely facilitates the adsorption and electrooxidation of dsDNA and the adsorbed layer can be successfully used for evaluating the interaction of DNA with methylene blue.     

血清样品中乙肝病毒的DNA电化学传感器检测

利用自组装单分子膜技术，将巯己基修饰的具有乙肝病毒(HBV)DNA序列特异性的单链DNA探针固定在金电极表面，制得DNA电化学传感器；以电活性的Hoechst 33258为指示剂，考察了该传感器对血清样品中乙肝病毒DNA的响应；探讨DNA电化学传感器在临床检测中的应用；将传感器法与荧光聚合酶链反应(PCR)法进行对比，两者的分析结果具有一致性。     

Preparation of a Reduced Graphene Oxide Wrapped Lithium‐Rich Cathode Material by Self‐Assembly

A lithium‐rich cathode material wrapped in sheets of reduced graphene oxide (RGO) and functionalized with polydiallyldimethylammonium chloride (PDDA) was prepared by self‐assembly induced from the electrostatic interaction between PDDA–RGO and the Li‐rich cathode material. At current densities of 1000 and 2000 mA g^?1, the PDDA–RGO sheet wrapped samples demonstrated increased discharge capacities, increasing from 125 to 155 mA h g^?1 and from 82 to 124 mA h g^?1, respectively. The decreased resistance implied by this result was confirmed from electrochemical impedance spectroscopy results, wherein the charge‐transfer resistance of the pristine sample decreased after wrapping with the PDDA–RGO sheets. The PDDA–RGO sheets served as a protective layer sand as a conductive material, which resulted in an improvement in the retention capacity from 56 to 81 % after 90 cycles.     

毛细管电泳-修饰电极电化学检测法测定饮用水中溴酸盐

通过静电组装技术在碳圆盘电极（PGE）表面制备{聚二烯丙基二甲基氯化铵（PDDA）/多壁碳纳米管（MWCNT）}n/PDDA多膜,并采用循环伏安法在多膜表面电化学修饰一磷钼酸（PMo12）膜,构筑PGE/{PDDA/MWNTs}5/PDDA/PMo12复合膜修饰电极,研究该复合膜修饰电极电化学及其对溴酸盐（BrO3-）电催化还原性质.在此基础上建立毛细管电泳-PGE/{PDDA/MWNTs}5/PDDA/PMo12修饰电极电化学检法定饮用水中溴酸盐分析新方法.在优化实验条件下,电泳峰面积与溴酸根浓度在5.0×10-8～5.0×10-5mol/L范围内呈良好性关系（r=0.9954）,检出为2.0×10-8mol/L（S/N=3）.     

Cyclic voltammetric detection of chemical DNA damage induced by styrene oxide in natural dsDNA layer-by-layer films using methylene blue as electroactive probe

In this work, an electrochemical sensor for detecting damage of natural double-stranded DNA (dsDNA) was constructed based on PSS/{PDDA/dsDNA}₃ layer-by-layer films, where PSS was poly(styrene sulfonate) and PDDA was poly(diallyldimethyl ammonium). When the PSS/{PDDA/dsDNA}₃ films assembled on pyrolytic graphite (PG) electrodes were immersed into methylene blue (MB) solution and loaded MB into the films, the formed PSS/{PDDA/dsDNA}₃-MB films in blank buffers at pH 7.0 showed a reversible cyclic voltammetric (CV) peak pair at −0.23 V vs. SCE for MB redox couple. In blank solutions, the MB loaded into the films was released gradually from the films, but the complete reloading of MB into the films could be realized by immersing the films into MB solution again, indicating the good reversibility of MB incorporation. However, after incubation in the solution of known genotoxic agent styrene oxide (SO), the damaged PSS/{PDDA/dsDNA}₃-MB films could not return to their original and fully-loaded state with reloading of MB, and showed smaller CV peak currents than those of intact PSS/{PDDA/dsDNA}₃-MB films. The relative peak current ratio, I_p,I/I_p,III, where I_p,I was the anodic peak current of intact DNA films in blank buffers after fully loading with MB and I_p,III was that of SO-damaged DNA films after reloading with MB, increased linearly with the incubation time with SO in the range of 5–40 min with a damage rate of 0.0099 min⁻¹. While the formation of SO adducts with dsDNA had no substantial effect on the dsDNA conformation, the steric hindrance of SO adducts with guanine or adenine blocked the intercalation of MB into the base pairs of dsDNA, resulting in the decrease of CV peak currents of loaded MB. The specific intercalation of MB into dsDNA base pairs and the sensitive electrochemical response of MB, combined with the unique feature of loading reversibility of MB in the DNA layer-by-layer films, make the difference in CV response between the intact and damaged dsDNA films become pronounced in the “loading/release/reloading” procedure. This may provide a new and general approach for constructing a biosensor for screening genetoxic chemicals in vitro.     

A Competitor-switched Electrochemical Sensor for Detection of DNA

A competitor‐switched electrochemical sensor based on a generic displacement strategy was designed for DNA detection. In this strategy, an unmodified single‐stranded DNA (cDNA) completely complementary to the target DNA served as the molecular recognition element, while a hairpin DNA (hDNA) labeled with a ferrocene (Fc) and a thiol group at its terminals served as both the competitor element and the probe. This electrochemical sensor was fabricated by self‐assembling a dsDNA onto a gold electrode surface. The dsDNA was pre‐formed through the hybridization of Fc‐labeled hDNA and cDNA with their part complementary sequences. Initially, the labeled ferrocene in the dsDNA was far from surface of the electrode, the electrochemical sensor exhibited a "switch‐off" mode due to unfavorable electron transfer of Fc label. However, in the presence of target DNA, cDNA was released from hDNA by target DNA, the hairpin‐open hDNA restored its original hairpin structure and the ferrocene approached onto the electrode surface, thus the electrochemical sensor exhibited a "switch‐on" mode accompanying with a change in the current response. The experimental results showed that as low as 4.4×10⁻¹⁰ mol/L target DNA could be distinguishingly detected, and this method had obvious advantages such as facile operation, low cost and reagentless procedure.     

A sensitive amperometric immunosensor for alpha-fetoprotein based on carbon nanotube/DNA/Thi/nano-Au modified glassy carbon electrode

A novel amperometric immunosensor for the determination of alpha-fetoprotein (AFP) was constructed using films of multi-wall carbon nanotubes/DNA/thionine/gold nanoparticles (nano-Au). Firstly, multi-wall carbon nanotubes (MWCNT) dispersed in poly(diallydimethlammonium chloride) (PDDA) were immobilized on the nano-Au film which was electrochemically deposited on the surface of glassy carbon electrode. Then a negatively charged DNA film was absorbed on the positively charged PDDA. Subsequently, thionine was attached to the electrode via the electrostatic interaction between thionine and the DNA. Finally, the nano-Au was retained on the thionine film for immobilization of AFP antibody (anti-AFP). The modification process was characterized by cyclic voltammetry (CV) and scanning electron microscope (SEM). The factors possibly influenced the performance of the proposed immunosensors were studied in detail. Under optimal conditions, the proposed immunosensor exhibited good electrochemical behavior to AFP in a two concentration ranges: 0.01–10.0 and 10.0–200.0 ng/mL with a relatively low detection limit of 0.04 ng/mL at three times the background noise. Moreover, the selectivity, repeatability and stability of the proposed immunosensor were acceptable.     

差分脉冲伏安法同时检测硝苯地平和尼群地平

采用绿色环保的还原剂聚二烯丙基二甲基氯化铵,制备石墨烯(GR)/聚二烯丙基二甲基氯化铵(PDDA)/铂纳米粒子(PtNPs)复合材料,在此基础上制备了GR/PDDA/PtNPs复合修饰电极,并采用透射电镜、电化学等方法对GR/PDDA/PtNPs进行表征。以pH=8.5的B.R缓冲溶液为支持电解质,采用循环伏安法研究了硝苯地平(Nifedipine,NF)和尼群地平(Nitrendipine,NT)在复合修饰电极上的电化学行为,并优化了电化学测量条件。NF溶液浓度为4.0×10(-7)~1.6×10(-4) mol·L^-1,NT溶液浓度为1.0×10^-6~1.4×10^-4 mol·L^-1,它们的还原峰电流与浓度成线性关系,检出限分别为5.0×10^-8 mol·L^-1,3.7×10^-7 mol·L^-1。所建立的方法成功应用于血药中NF、NT的测定,获得可靠满意的结果。     

碳纳米管/聚二烯丙基二甲基氯化铵/磷钼酸复合膜的组装及其在溴酸盐检测中的应用

通过静电层层组装技术在玻碳(GC)电极表面制备{多壁碳纳米管(MWCNT)/聚二烯丙基二甲基氯化铵(PDDA)}n多层膜,并采用循环伏安法在多层膜的表面电化学修饰一层磷钼酸(PMo12)膜,构筑GC/{MWCNT/PDDA}n-PMo12复合膜修饰电极.利用SEM对比观察{MWCNT/PDDA}n和{PDDA/MWCNT}n-PMo12的微观结构,并研究该复合膜修饰电极的电化学及其对溴酸盐(BrO3-)电催化还原性质.在此基础上研发一种基于GC/{MWCNT/PDDA}n-PMo12复合膜修饰电极的电流型BrO3-传感器,该传感器表现出明显增大的响应电流.在最优的实验条件下,采用电流时间曲线(i-t)法考察该复合膜修饰电极对BrO3-的安培响应.实验结果表明,该传感器在BrO3-浓度为50～400nmol/L的范围内具有良好的线性关系,相关系数R2为0.9950,响应时间为1.53s,检出限为20nmol/L,灵敏度为13.81mA(mmol/L)-1cm-2.