纳米二氧化钛对水中Sn(Ⅱ)、Sn(Ⅳ)和二丁基锡吸附性能的研究

采用流动注射-氢化物发生-原子吸收光谱法研究纳米TiO2对Sn(Ⅱ)、Sn(Ⅳ)和二丁基锡(DBT)的吸附作用,探讨在不同pH值、吸附时间、试样浓度和试样体积下,不同用量的纳米TiO2的吸附效果以及试样的洗脱条件和效率。结果表明,Sn(Ⅱ)和Sn(Ⅳ)的浓度≤6.0μg/mL、体积≤500 mL、pH=3.0;DBT的浓度≤0.2μg/mL、体积≤50 mLp、H=4.0,30 mg纳米TiO2对Sn(Ⅱ)、Sn(Ⅳ)和DBT的吸附率≥90.0%。在25℃条件下,纳米TiO2对Sn(Ⅱ)、Sn(Ⅳ)和DBT的饱和吸附容量分别为23.6μg/mg、13.7μg/mg和0.628μg/mg,适用于无机锡和二丁基锡污染的吸附去除及对水中无机及丁基锡的定量富集。用4 mol/L HCl对吸附的Sn(Ⅱ)、Sn(Ⅳ)和DBT进行洗脱,洗脱率达到98%以上,可做为样品分析的前处理方法。     

印迹壳聚糖/凹土分离富集-FAAS测定水中痕量镉

建立了用离子印迹壳聚糖/凹土(ⅡGA)分离富集-火焰原子吸收光谱(FAAS)测定痕量镉的新方法.在动态吸附条件下,系统地研究了溶液pH值、流速、洗脱条件和干扰离子对痕量镉分离富集的影响;在pH4.5、上样流速为0.60 mL/min的条件下,镉能被ⅡCA定量富集;吸附的镉可用1.0 mol/L HCl-0.1 mol/...     

交联壳聚糖在汞形态分析中的应用

研究了一种新型溶于水，酸，碱的交联壳聚糖在汞形态分析中的应用。以ＥＤＴＡ为络合剂，交联壳聚糖能选择性富集分离无机汞；以ＫＩ作为络合剂，交联壳聚糖同时富集甲基汞，乙基汞和苯基汞，０．４ｍｏｌ／ＬＮａＯＨ可定量洗脱苯基汞，１．０ｍｏｌ／ＬＮａＯＨ定量洗脱烷基汞，     

离子印迹壳聚糖/凹土分离富集-火焰原子吸收光谱测定中药材中痕量Cd(Ⅱ)的研究

建立了离子印迹壳聚糖/凹凸棒石(IICA)分离富集-火焰原子吸收光谱(FAAS)测定中药材中痕量Cd(Ⅱ)的新方法。在动态吸附条件下,系统研究了溶液pH值、流速、洗脱条件和干扰离子对痕量Cd(Ⅱ)分离富集的影响。研究表明,在pH为4.5,上样流速为0.60mL/min条件下,Cd(Ⅱ)能被IICA定量富集;吸附的Cd(Ⅱ)可用1.0mol/L HCl-0.1mol/L甲基异丁酮的乙醇溶液,在流速为0.96mL/min条件下完全洗脱。优化条件下,IICA对Cd(Ⅱ)的动态吸附容量为56.45mg/g。线性范围为0.00097～1.28mg/L,r=0.9994,检出限(3σ,n=11)为0.97μg/L,相对标准偏差为1.32%(n=6,c=0.08mg/L),回收率在96.5%～106.4%之间。该方法操作简便,灵敏度和精密度高,可应用于实际中药材样品中痕量镉的测定。     

交联壳聚糖预富集分离-石墨炉原子吸收光谱法测定痕量银(Ⅰ)

研究了交联壳聚糖(CCTS)对银(Ⅰ)的吸附性能,提出了用CCTS作为富集剂预富集分离水样中痕量银的新方法。研究结果表明:在pH 3.0时,CCTS对银的吸附率达99%以上,其饱和吸附量为0.6 mg/g;采用8 mL 0.5 moL/L的氨水可将吸附在CCTS上的银定量洗脱。用CCTS将水中痕量银(Ⅰ)富集20倍,石墨炉原子吸收光谱法(GFAAS)进行检测,检出限(3σ,n=6)为0.406μg/L,相对标准偏差(RSD)小于6.8%。该方法也适合贵金属银的回收利用。     

激光共振电离质谱法测量锡的同位素比

采用实验室研制的激光共振电离质谱仪,建立了锡(Sn)同位素的激光共振电离质谱分析方法.测量了锡原子的自电离态光谱,确认了锡的一条三色三光子共振电离路径,其各步激发/电离的激光波长分别为λ1=286.4 nm、λ2=811.6 nm、λ3=823.7 nm;通过将样品与氧化石墨烯溶液混合制样,有效提高了锡样品的电热原子化效率,1μg锡的总探测效率达到3×10-5以上,是直接滴样方式的4.5倍左右.采用本方法对锡、锑、硫(1:1:1,m/m)混合模拟样品进行测试,实现了锡的选择性电离,有效避免了测量过程中锑、硫对锡的同量异位素干扰,样品中主要同位素比116 Sn/120 Sn,117 Sn/120 Sn,118 Sn/120 Sn和119 Sn/120 Sn测量的相对标准偏差均°1%.结果表明,本方法能够有效解决TIMS、ICP-MS等商业质谱仪在锡同位素质谱分析过程中的同量异位素干扰难题,有望应用于反应堆乏燃料中裂变产物121m Sn、126 Sn的测量.     

接枝壳聚糖对铅、镉吸附行为研究及应用

在碱性条件下,用环氧氯丙烷交联制备水不溶性交联壳聚糖(CCTS),将丙烯腈单体接枝到CCTS分子骨架上制得接枝壳聚糖(CTCA)。研究了CTCA对水中Pb2 、Cd2 的吸附富集行为和洗脱行为,用原子吸收光谱法测定。结果表明,溶液的pH值为6.0时,Pb2 、Cd2 的吸附率达94%和95%,吸附容量分别达到56.6 mg/g、47.0 mg/g。用1 mol/L HCl洗脱,Pb2 、Cd2 的解吸率均可达97%。方法的检出限为:Pb2 ,0.065μg/L;Cd2 ,0.024μg/L。对10 mg/L的Pb2 、Cd2 溶液进行分离富集和测定,其相对标准偏差为3.4%和5.2%。方法已用于天然水中Pb2 、Cd2 的分离富集和测定,其回收率:Pb2 ,94%~101.9%;Cd2 ,95.6%~108%。     

邻苯三酚红修饰碳糊电级阳极溶出伏安法测定痕量锡的研究

研制了邻苯三酚红 ( PR)修饰碳糊电极 ,研究了采用该电极测定痕量锡的阳极溶出伏安法。在 0 .1 5 mol/L乙酸盐缓冲溶液 ( p H 4.5 )中 ,通过开路富集 ,Sn( )与修饰电极表面的邻苯三酚红生成络合物而富集于电极表面 ,然后介质交换至 4.0mol/L盐酸中 ,于 - 0 .80 V还原后再进行阳极化扫描 ,于 - 0 .69V左右获得一灵敏的 Sn的溶出峰 ,二次导数峰电流与 Sn( )浓度在 1 .68× 1 0 - 8～ 1 .68× 1 0 - 6mol/L范围内呈现良好的线性关系 ,检出限达 8× 1 0 - 9mol/L。对电极反应机理进行了讨论 ,方法已应用于罐头食品中锡的测定     

壳聚糖富集火焰原子吸收法测定天然水中痕量镉

提出了壳聚糖分离富集火焰原子吸收法检测水中痕量镉的新方法。研究了富集的最佳条件及洗脱方法。回收率达98％,灵敏度0.021μg·L~(-1)。方法灵敏度高,选择性好,用于天然水中痕量镉的测定,获得满意结果。     

邻苯三酚红修饰碳糊电极阳极溶出伏安法测定痕量锡的研究

研制了邻苯三酚红(PR)修饰碳糊电极,研究了采用该电极测定痕量锡的阳极溶出伏安法.在0.15 mol/L乙酸盐缓冲溶液(pH 4.5)中,通过开路富集,Sn(Ⅳ)与修饰电极表面的邻苯三酚红生成络合物而富集于电极表面,然后介质交换至4.0mol/L盐酸中,于-0.80 V还原后再进行阳极化扫描,于-0.69 V左右获得一灵敏的Sn的溶出峰,二次导数峰电流与Sn(Ⅳ)浓度在1.68×10-8～1.68×10-6mol/L范围内呈现良好的线性关系,检出限达8×10-9mol/L.对电极反应机理进行了讨论,方法已应用于罐头食品中锡的测定.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.