Fe2+/UV催化臭氧-曝气生物滤池降解腈纶废水研究

腈纶废水是一种难降解的有毒有机废水。本文采用Fe2+/UV催化臭氧-曝气生物滤池降解腈纶废水,探讨了臭氧浓度和紫外光辐射强度等影响因素对腈纶废水的COD去除效果的影响,并考察了紫外催化臭氧氧化单元和曝气生物滤池单元对COD去除的协同作用。结果表明,臭氧浓度对COD的去除率影响较大,臭氧浓度下降25%时,臭氧催化氧化和曝气生物滤池单元处理的COD去除率分别下降了12.53%和15.98%。紫外光强度对臭氧催化氧化单元的COD去除率影响较小,但对曝气生物滤池单元影响较大。臭氧催化氧化单元和曝气生物滤池单元COD去除率之比为1∶2,其协同作用使总出水COD值稳定在较低水平。     

絮凝-漂白粉催化氧化处理印染废水

采用絮凝-漂白粉催化氧化法,筛选出硫酸镁催化剂,提高难生化处理的印染废水对色度、COD的去除效果。实验结果表明,对COD_(Cr) 592 mg/L、色度625倍、pH 9.82、SS 150 mg/L的某印染废水,当废水p H为6时,投加Al_2(SO_4)_3·18H_2O 400 mg/L、聚丙烯酰胺(PAM)2 mg/L,催化剂硫酸镁80 mg/L,有效氯30%的漂白粉1.0 g/L,CODCr最终去除率达到88.2%,色度去除率98.4%,浊度去除率86.6%,出水pH为6,达到国家二级排放标准。催化氧化的脱色速率提高近一倍,结果对印染废水的处理研究和实际应用具有一定价值。     

铁炭微电解-亚铁还原氧化法处理花菁废水的研究

研究了微电解-亚铁还原氧化法在处理花菁废水上的应用,结果显示,经过处理,废水色度的去除率>97%,化学需氧量(COD)的去除率>90%.研究了影响处理效果的因素,对于废水中有机物的去除、脱色以及废水可生化性的提高进行了探讨,并通过紫外-可见光谱和色质联用(GC/MS)对处理前后的废水组分进行了分析.     

混凝吸附法联合处理小麦麸膳食纤维废水

用聚合硫酸铝铁为混凝剂,阳离子型聚丙烯酰胺为助凝剂,活性炭为吸附剂,采用混凝吸附的方法,处理了小麦麸膳食纤维废水.结果表明当聚合硫酸铝铁(PAFS)的质量浓度为500 mg/L,聚丙烯酰胺(PAM)的质量浓度为10 mg/L,pH为4.21时,混凝处理后的废水COD去除率最大.絮凝后水样经活性炭吸附后COD去除率可达85.82%,色度去除率为100%,浊度去除率为93.03%.     

进水盐度对膜生物反应器运行效能的影响研究

进水盐度对膜生物反应器(MBR)的运行效能影响显著,尤其是进水含盐量为5 g/L时,明显恶化了污泥可滤性,膜污染速率加快;MBR混合液中溶解性微生物产物(SMP)和胞外聚合物(EPS)含量随钠离子浓度变化而变化,其中SMP中蛋白质含量与钠离子浓度密切相关;与紧密结合态EPS(TB)相比,钠离子含量对松散结合态EPS(LB)浓度的影响更大;不同盐度对COD及NH4+-N影响不明显,系统对COD及NH4+-N的去除效果稳定,分别保持在92%及94%以上,高盐度对MBR总磷去除率降低明显。     

UF-两段厌氧处理茶多酚废水的研究

采用前置超滤膜(UF)的两相厌氧工艺对原水COD为18362.6mg/L,荼多酚为3608.3mg/L、色度为2624.2倍的茶多酚生产废水进行为期90d的实验研究.结果表明,当实验压力为0.2Mpa时,膜组件对COD去除率为63.4%,茶多酚去除率为95.1%,色度去除率为93.4%.然后,对两相厌氧工艺的投配率、P含量和酸化段水力停留时间(HRT1)对废水COD、色度与茶多酚去除率和产气率的影响进行了研究.当投配率为15.0%、P含量为38.1mg/L、HRT1=24h,该工艺达到最佳处理效果,出水COD为1288.1mg/L,COD去除率为80.8%,色度为95.6倍,色度去除率为44.6%,残余茶多酚为119.8mg/L,茶多酚去除率为32.3%,产气率为0.85m3/kg COD,与未采用UF预处理的两相厌氧水解工艺相比,COD、色度和荼多酚去除率分别提高23.40%,10.2%和1613%,产气率增加0.15m3/kg COD.     

双极室联合处理啤酒废水的微生物燃料电池

构建了双极室连续流联合处理废水的微生物燃料电池(MFC), 该MFC阳极室的出水直接用于阴极室的进水, 利用阴极室的好氧微生物进一步降解有机物. 以啤酒废水作底物, 研究了该MFC的产电性能和废水处理效果. 结果表明, 采用双极室连续流MFC可以大大提高废水的处理效果, 对啤酒废水化学需氧量(COD)的总去除率可达92.2%~95.1%, 其中阳极室中COD去除率为47.6%~56.5%. MFC的开路电压为0.451 V, 最大输出功率为2.89 W/m³. 实验中抑制MFC性能的主要因素是阴极的极化损失, 通过降低进入阴极室溶液的COD浓度、采用优质的阴极材料和加大阴极室内的曝气量等方法进一步优化电池的性能.     

微生物燃料电池处理餐饮废水及同步发电性能研究

针对食堂餐饮废水,建立微生物燃料电池实验系统,研究微生物燃料电池废水处理与同步发电性能。首先使用Fe(NO3)3溶液作为阴极电解液进行实验,证明餐饮废水生物降解及产电的可行性;分别采用NaCl溶液和K3[Fe(CN)6]溶液作为阴极电解液进行对比实验,研究不同运行环境下微生物燃料电池的发电性能和污水净化效果。结果表明,采用NaCl溶液和K3[Fe(CN)6]溶液作为阴极电解液时的COD去除率分别是30%和22%左右,平均电流密度分别为5.6和5.2mA/m2。在污水稀释比为2∶1、NaCl电解液浓度为0.4mol/L的情况下,微生物燃料电池系统的发电性能和净水效果达到最佳状态,稳态电流密度为8.8mA/m2,COD去除率为33.3%。     

不同电催化工艺下苯酚的降解特性

比较了苯酚在电催化阳极氧化(AE)、阴阳两极协同降解(ACE)及亚铁离子存在下阴阳两极协同催化降解(FeACE)₃种工艺下的降解及产物变化.在电流0.25A下处理2h,废水中COD的去除率在AE下仅30％,在ACE下为60％,而在FeACE下高达90％.苯酚降解的中间产物主要为对苯二酚、邻苯二酚、间苯二酚、对苯醌、顺丁烯二酸、反丁烯二酸和草酸等.在FeACE工艺下,中间产物还有甲酸.最终产物为CO₂.FeACE不仅提高了COD的去除速率,而且还有助于有毒中间产物的迅速消除,并使有机物彻底氧化,因而在环境保护中更具有应用前景.采用水杨酸作捕获剂证实了3种电催化工艺降解有机物的羟基自由基作用机理,其进攻苯环的活性顺序为:对位>邻位>间位,根据产物变化提出了苯酚降解路径.     

一种复合脱色剂在印染废水中的应用研究

以甲醛、双氰胺、醋酸钠、氯化铵、氯化铝等为原料制备了一种印染废水脱色絮凝剂T-1。采用福州某纺织印染有限公司的印染废水为处理对象,以脱色率为主要考核指标,讨论了T-1的投加量、pH值、废水温度等对絮凝效果的影响。实验结果表明,双氰胺-甲醛缩聚物对印染废水具有优良的脱色絮凝效果,当投加量为100mg/L,废水温度为30℃,pH=8时,处理效果最佳,色度去除率达70%,COD去除率为78.3%。而且其絮凝性能明显优于聚合氯化铝(PAC)、聚合硫酸铝(PAS)絮凝剂。     

Li_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3,Na_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3的离子交换研究

研究了在不同温度下的NaNO3和AgNO3水溶液中Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3离子交换行为.实验表明Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3均显示出了高选择性与Na+和Ag+进行离子交换的特征,且对Ag+的选择性高于Na+.升高温度可显著提高Ag/Li和Ag/Na的交换反应速度.     

Crystal growth, structure determination, and optical properties of new potassium-rare-earth silicates K3RESi2O7 (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu)

Single crystals of K₃RESi₂O₇ (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu) were grown from a potassium fluoride flux. Two different structure types were found for this series. Silicates containing the larger rare earths, RE=Gd, Tb, Dy, Ho, Er, Tm, Yb crystallize in a structure K₃RESi₂O₇ that contains the rare-earth cation in both a slightly distorted octahedral and an ideal trigonal prismatic coordination environment, while in K₃LuSi₂O₇, containing the smallest of the rare earths, lutetium is found solely in an octahedral coordination environment. The structure of K₃LuSi₂O₇ crystallizes in space group P6₃/mmc with a=5.71160(10) Å and c=13.8883(6) Å. The structures containing the remaining rare earths crystallize in the space group P6₃/mcm with the lattice parameters of a=9.9359(2) Å, c=14.4295(4) Å, (K₃GdSi₂O₇); a=9.88730(10) Å, c=14.3856(3) Å, (K₃TbSi₂O₇); a=9.8673(2) Å, c=14.3572(4) Å, (K₃DySi₂O₇); a=9.8408(3) Å, c=14.3206(6) Å, (K₃HoSi₂O₇); a=9.82120(10) Å, c=14.2986(2) Å, (K₃ErSi₂O₇); a=9.80200(10) Å, c=14.2863(4) Å, (K₃TmSi₂O₇); a=9.78190(10) Å, c=14.2401(3) Å, (K₃YbSi₂O₇). The optical properties of the silicates were investigated and K₃TbSi₂O₇ was found to fluoresce in the visible.     

Near infrared study of aqueous rare-earth ethylsulfates

The near infrared spectra of aqueous solutions of the ethylsulfates of La, Nd, Gd, Tb, Er, Yb, Lu, Y, and Na have been determined from about 0.2 mol-dm^–3 to nearly saturation. The extinction coefficients of water have been calculated taking into account the absorption of ethylslfate anions determined in separate experiments. Their values appeared to be nearly the same as that of pure water. The relative contents of free OH groups in 0.5 and 0.7M solutions have been estimated from the absorbances at 1160 nm. They were lower in solutions of the heavy rare-earth ethylsulfates (Tb, Er, Yb, Lu) than in equimolar solutions of the lighter ones (La, Nd), confirming our previous view that secondary hydration of the heavy trivalent rare-earth cations is distinctly stronger than that of the lighter ones. A comparison of the spectra of these aqueous ethylsulfates with those of perchlorates shows that the structure-breaking ability of the C₂H₅SO ₄ ^– ion is much smaller than that of perchlorate anion.     

The crystal chemistry of Bi6TP2O15+x, T=Fe, Ni, Zn: Isomorphism and polymorphism, structural relationship to Bi6TiP2O16

The crystal structures of compounds with nominal compositions Bi₆FeP₂O_15+x (I), Bi₆NiP₂O_15+x (II) and Bi₆ZnP₂O_15+x (III) were determined from single-crystal X-ray diffraction data. They are monoclinic, space group I2, Z=2. The lattice parameters for (I) are a=11.2644(7), b=5.4380(3), c=11.1440(5) Å, β=96.154(4)°; for (II) a=11.259(7), b=5.461(4), c=11.109(7) Å, β=96.65(1)°; for (III) a=19.7271(5), b=5.4376(2), c=16.9730(6) Å, β=131.932(1)°. Least squares refinements on F² converged for (I) to R1=0.0554, wR₂=0.1408; for (II) R₁=0.0647, wR₂=0.1697; for (III) R₁=0.0385, wR₂=0.1023. The crystals are complexly twinned by 2-fold rotation about , by inversion and by mirror reflection. The structures consist of edge-sharing articulations of OBi₄ tetrahedra forming layers in the a-c plane that then continue by edge-sharing parallel to the b-axis. The three-dimensional networks are bridged by Fe and Ni octahedra in (I) and (II) and by Zn trigonal bipyramids in (III) as well as by oxygen atoms of the PO₄ moieties. Bi also randomly occupies the octahedral sites. Oxygen vacancies exist in the structures of the three compounds due to required charge balances and they occur in the octahedral coordination polyhedron of the transition metal. In compound (III), no positional disorder in atomic sites is present. The Bi-O coordination polyhedra are trigonal prisms with one, two or three faces capped. Magnetic susceptibility data for compound (I) were obtained between 4.2 and 350 K. Between 4.2 and 250 K it is paramagnetic, μ_eff=6.1 μ_B; a magnetic transition occurs above 250 K.     

Structural studies of five layer Aurivillius oxides: A2Bi4Ti5O18 (A=Ca, Sr, Ba and Pb)

The room temperature structures of the five layer Aurivillius phases A₂Bi₄Ti₅O₁₈ (A=Ca, Sr, Ba and Pb) have been refined from powder neutron diffraction data using the Rietveld method. The structures consist of [Bi₂O₂]²⁺ layers interleaved with perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks. The structures were refined in the orthorhombic space group B2eb (SG. No. 41), Z=4, and the unit cell parameters of the oxides are a=5.4251(2), b=5.4034(1), c=48.486(1); a=5.4650(2), b=5.4625(3), c=48.852(1); a=5.4988(3), b=5.4980(4), c=50.352(1); a=5.4701(2), b=5.4577(2), c=49.643(1) for A=Ca, Sr, Ba and Pb, respectively. The structural features of the compounds were found similar to n=2-4 layers bismuth oxides. The strain caused by mismatch of cell parameter requirements for the [Bi₂O₂]²⁺ layers and perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks were relieved by tilting of the TiO₆ octahedra. Variable temperature synchrotron X-ray studies for Ca and Pb compounds showed that the orthorhombic structure persisted up to 675 and 475 K, respectively. Raman spectra of the compounds are also presented.     

电感耦合等离子体光谱法(ICP-AES)测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量

针对银精矿样品复杂,难消解的特点,研究了不同酸溶法和碱熔法对样品的消解情况,建立了硝酸,盐酸,氢氟酸,高氯酸消解银精矿的方法。根据元素灵敏度和抗干扰性,选定各元素的测定波长。通过酸溶样和碱熔样测定结果比对,验证了方法准确性。建立了四酸消解-电感耦合等离子体光谱法测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的方法,元素的线性相关系数均在0.9999以上。通过共存元素干扰实验,确定了银精矿中高含量元素(铜、铅、锌、铁、锑、铋等)对测定元素结果没有影响。方法检出限：Cu 0.0063 mg/L, Pb 0.0159 mg/L ,Zn 0.0090 mg/L,As 0.0192 mg/L, Cd 0.0093 mg/L ,Ca 0.0084 mg/L, Mg 0.0075 mg/L, Mn 0.0081 mg/L。测定下限：Cu 0.0105mg/L,Pb 0.0265 mg/L, Zn 0.0150 mg/L, As 0.0320 mg/L, Cd 0.0155 mg/L, Ca 0.0140 mg/L, Mg 0.0125 mg/L,Mn 0.0135 mg/L。3个样品的相对标准偏差在0.87%~3.56%之间,加标回收率在95.00%~103.56%之间。方法流程短,操作简单,快速,灵敏度和再现性高,结果准确可靠,可以满足银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的测定。     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃-Bi₂O₃-ZnO-Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1 350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1 364,介电损耗低至1.2%。     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

The Phase Relations in the System In2O3–TiO2–MgO at 1100 and 1350°C

The phase relations in the system In₂O₃–TiO₂–MgO at 1100 and 1350°C are determined by a classical quenching method. In this system, there are four pseudobinary compounds, In₂TiO₅, MgTi₂O₅ (pseudobrookite type), MgTiO₃ (ilmenite type), and Mg₂TiO₄ (spinel type) at 1100°C. At 1350°C, in addition to these compounds there exist a spinel-type solid solution Mg_2−xIn_2xTi_1−xO₄ (0≤x≤1) and a compound In₆Ti₆MgO₂₂ with lattice constants a=5.9236(7) Å, b=3.3862(4) Å, c=6.3609(7) Å, β=108.15(1)°, and q=0.369, which is isostructural with the monoclinic In₃Ti₂FeO₁₀ in the system In₂O₃–TiO₂–MgO. The relation between the lattice constants of the spinel phase and the composition nearly satisfies Vegard's law. In₆Ti₆MgO₂₂ extends a solid solution range to In₂₀Ti₁₇Mg₃O₆₇ with lattice constants of a=5.9230(5) Å, b=3.3823(3) Å, c=6.3698(6) Å, β=108.10(5)°, and q=0.360. The distributions of constituent cations in the solid solutions are discussed in terms of their ionic radius and site preference effect.     

Structure Study of Bi2.5Na0.5Ta2O9 and Bi2.5Nam−1.5NbmO3m+3 (m=2-4) by Neutron Powder Diffraction and Electron Microscopy

The crystal structures of Bi_2.5Na_0.5Ta₂O₉ and Bi_2.5Na_m-1.5Nb_mO_3m+3 (m=3,4) have been investigated by the Rietveld analysis of their neutron powder diffraction patterns (λ=1.470 Å). These compounds belong to the Aurivillius phase family and are built up by (Bi₂O₂)²⁺ fluorite layers and (A_m-1B_mO_3m+1)^2- (m=2-4) pseudo-perovskite slabs. Bi_2.5Na_0.5Ta₂O₉ (m=2) and Bi_2.5Na_2.5Nb₄O₁₅ (m=4) crystallize in the orthorhombic space group A2₁am, Z=4, with lattice constants of a=5.4763(4), b=5.4478(4), c=24.9710 (15) and a=5.5095(5), b=5.4783(5), c=40.553(3) Å, respectively. Bi_2.5Na_1.5Nb₃O₁₂ (m=3) has been refined in the orthorhombic space group B2cb, Z=4, with the unit-cell parameters a=5.5024(7), b=5.4622(7), and c=32.735(4) Å. In comparison with its isostructural Nb analogue, the structure of Bi_2.5Na_0.5Ta₂O₉ is less distorted and bond valence sum calculations indicate that the Ta-O bonds are somewhat stronger than the Nb-O bonds. The cell parameters a and b increase with increasing m for the compounds Bi_2.5Na_m-1.5Nb_mO_3m+3 (m=2-4), causing a greater strain in the structure. Electron microscopy studies verify that the intergrowth of mixed perovskite layers, caused by stacking faults, also increases with increasing m.