国产全光纤结构激光器实现245 W高功率激光输出

 以国产掺镱光纤为增益介质,利用国产泵浦源和光纤器件,构建了主振荡功率放大（MOPA）结构的全国产大功率全光纤激光器。激光器包括10 W种子激光器和高功率放大器两部分。在注入最大泵浦功率为356 W时,获得了245 W波长1 080 nm激光的稳定输出,光-光效率为69%。激光器单次连续出光时间约30 min,功率稳定性在1%以内。目前激光器输出功率受限于泵浦功率,增加泵浦源的数目有望进一步提高输出功率。     

基于MOPA结构的1120nm掺Yb光纤放大器

基于主振荡功率放大器,采用1120nm光纤激光器作为种子激光,将其注入20m大模场面积单模双包层掺Yb光纤放大器,并用976nm半导体激光器泵浦实现了1 120nm信号光输出.实验中将注入种子激光功率预设为10mW,当半导体激光器泵浦功率增大至1.5 W时,放大器系统开始输出1 120nm信号光.当泵浦功率低于3.4W时,信号光功率随泵浦功率缓慢增长,系统斜率效率较低;而当泵浦功率高于3.4W时,信号光功率随泵浦功率线性增长,斜率效率明显增大,达到48.5%.限于最大注入泵浦功率为6.8W,放大器输出最高1 120nm信号光功率为1.97W,总的光-光转化效率为29%.输出信号光中心波长为1 120.89nm,线宽为0.02nm,极好地保持了种子激光的特性.结合实验情况,利用双包层光纤放大器的稳态理论模型,采用有限差分方法模拟了放大器输出信号光功率随泵浦光功率的变化曲线,结果显示理论模拟所得变化趋势与实验结果吻合良好,系统将在泵浦功率达到200W左右时达到饱和状态,说明目前光纤放大器系统具有很大的功率提升空间.     

高功率全光纤激光器特性

介绍了采用国产光纤光栅研制的全光纤激光器,单端泵浦获得468 W的连续激光输出。从理论上分析了光纤光栅的反射率与波长的关系,计算了输出谱宽值,与实验测得的数据相符。全光纤激光器的光-光转换效率达到70%,且随着功率的增加,光纤光栅的中心波长有向长波方向漂移的趋势。在最高输出功率下180 s之内输出功率波动在0.04%以内。     

分布式抽运连续光纤激光器研究

为了避免高功率光纤激光器中光纤端面出现热效应问题,依据多点级联结构的耦合器,对分布式抽运的光纤激光器进行了研究。首先,介绍了实验室自主研制的级联耦合器。然后,分析了耦合器插入对光纤激光器的影响。最后,选用自制的耦合器搭建了分布式抽运的光纤激光器。实验结果表明:对耦合器插入损耗的研究,能够促进高功率级联耦合器的实现。在光纤激光器结构中,975 nm泵浦功率注入1.1 k W时,1 080nm激光功率输出为770 W,光-光转换效率为77%。在主控振荡功率放大结构中,激光功率输出为635 W,放大级的光-光转换效率为78%。分布式抽运方式可以使泵浦光多点注入,避免了热量的集中,能够获得千瓦级的激光功率输出。     

窄线宽1064 nm光纤激光泵浦高效率中红外3.8μm MgO:PPLN光参量振荡器

采用放大1064 nm掺镱光纤激光器作为泵浦源,实现了中红外3.8μm MgO:PPLN光参量振荡(OPO)激光输出。在泵浦源中,采用分布式反馈激光器(DFB)作为种子源来实现光纤激光窄线宽的调制,实现线宽2.5 nm到0.1 nm的压缩,最大平均输出功率可达40 W。进一步对不同泵浦线宽条件下中红外3.8μm MgO:PPLN OPO激光进行研究,最终在泵浦功率为18.1 W、线宽为0.1 nm、重频为1 MHz、脉宽为2 ns时,获得了最高平均输出功率为2.06 W的3822.5 nm激光输出,光-光转换效率为11.38%,光束质量为M2=2.34,提高了窄线宽泵浦对中红外MgO:PPLN OPO激光输出效率。     

光子晶体光纤放大器增益特性的实验研究

 采用掺Yb³⁺双包层光子晶体光纤作为放大器的增益介质,在双端泵浦方式下,理论并实验研究了不同信号光时放大器的增益特性。在双端泵浦方式下,泵浦总功率为150.2 W、信号光功率为6 W时,获得了72 W的功率输出,斜率效率达到了60%。实验发现当泵浦总功率超过一定值时,由光纤端面反射形成的振荡腔引起放大器寄生振荡,并由于各种非线性效应出现了自脉动现象,影响了输出功率的进一步提高。     

全光纤激光器实现kW级功率输出

 搭建了一台全光纤结构的光纤激光器。采用双端泵浦结构,共有36个泵浦输入端。在使用其中的24个泵浦输入端,泵浦功率为1 477 W时,获得了1 008 W高功率输出,光光转换效率为68%。输出激光的中心波长为1 082 nm,半波全宽为3 nm。目前激光器输出功率受限于泵浦功率,增加泵浦源的数目有望进一步提高输出功率。     

端面泵浦掺Yb3+双包层光纤激光器

从双包层光纤激光器的速率方程出发，得到了光纤中泵浦光与激光的功率分布、输出功率与泵浦功率的关系、腔镜反射率及光纤长度对输出功率的影响。研究结果表明：输出激光功率与光纤长度及后腔镜反射率有很强的依赖关系，存在一个输出功率最大的最佳光纤长度。后腔镜反射率越大，输出激光功率越小；当光纤长度较短时，在输出端放置反射镜使泵浦光高反射，可以提高输出功率和效率。通过对端面泵浦掺Yb3+双包层光纤激光器进行理论分析和实验研究，得到输出激光的中心波长为1088.3nm，斜率效率为33.7%，最大输出功率为1.75W。     

67.9W高功率全光纤白光超连续谱激光器

利用自主研发的全光纤被动锁模激光器以及高功率光纤模场匹配器,将145 W的皮秒脉冲耦合进国产光子晶体光纤,实现了67.9 W的高功率全光纤结构白光超连续谱输出,光谱范围为500~1700nm,10dB光谱宽度大于1000nm(泵浦波长除外)。整个激光器系统的光-光(半导体泵浦源输出激光-超连续谱输出激光)转化效率达到33.8%。     

七芯光子晶体光纤中百瓦量级超连续谱的产生

采用平均功率为141.6 W的皮秒光纤激光泵浦一段国产七芯光子晶体光纤,获得了平均功率为104.2 W、连续光谱覆盖范围从750至1700 nm以上的超连续谱输出.详细研究了超连续光谱随泵浦功率增加的演变过程,并对基于该七芯光子晶体光纤的超连续谱光源的光谱拓展和功率提升潜力进行相关的分析和讨论.该研究结果对高功率超连续谱光源的发展具有一定的参考价值.     

Picosecond laser oscillator with a cavity design for stable CW mode-locking operation

A detailed design of a picosecond laser oscillator is made by using optical resonance theory and semiconductor saturable absorber mirror continuous wave mode-locked technology. Mode parameters in the optical resonance including beam sizes on the laser crystal and mode locker are calculated. By theoretical calculations, 3.7 W output power is obtained at a pump power of 11 W and the optical to optical efficiency is 34% in the designed model of picosecond laser. Based on the detailed design, an experiment is proceeded and a picosecond laser oscillator of about 3.5 W output power with 10.6 W pump power is fabricated. The optical to optical efficiency of the laser is 33%, the pulse duration is about 20 ps, and the repetition rate is about 80.3 MHz. The oscillator presents long-term stability in the experiment.     

20 W all fiber supercontinuum generation from picosecond MOPA pumped photonic crystal fiber

An all fiber high power supercontinuum (SC) source is demonstrated by pumping a section of photonic crystal fiber (PCF) with a picosecond MOPA laser. The core of the PCF is enlarged at the input end through a serious of PCF post processing method to match the output fiber of the picosecond laser, to ensure low loss splicing, hence high power operation of the whole system. The supercontinuum output spectrum covers the wavelength range from 650 nm to beyond 1700 nm. Limited by available pump power, 20 W super-continuum output power is obtained under 29.5 W picosecond pump power, giving a high optical to optical conversion efficiency of 67.8%.     

Interferometric output coupling of ring optical oscillators

We demonstrate the successful deployment of an antiresonant ring (ARR) interferometer within a ring optical resonator and its use for absolute optimization of output power. The integration of the ARR interferometer in a folded arm of the ring oscillator provides continuously variable output coupling over broad spectral range and under any operating conditions. We demonstrate the technique using a picosecond optical parametric oscillator (OPO), where we show continuously adjustable output coupling and optimization of the output power for different pump power conditions, from 3.5 W to 13.5 W. By operating the OPO under an optimized output coupling at 14 W of pump power, we obtain >5 W of extracted signal power, more than 2.6 times that with a ~5% conventional output coupler. We also show that the inclusion of the ARR interferometer has no detrimental effect on the spatial, temporal, and spectral characteristics of OPO output.     

High power continuous-wave diode-laser-pumped Nd:YAG laser

We report on a diode-laser-pumped cw Nd: YAG laser operating at a power level of 150 W. By using a transverse pump geometry, the radiation of 54 diode lasers with an output power of 10 W each is coupled into a Nd:YAG rod. In multimode operation, an optical slope efficiency of 32% and an optical to optical efficiency of 29% are obtained. In TEM₀₀ operation, an output power of more than 30 W is realized with an optical to optical efficiency of 10%.     

Continuous-wave and pulsed laser performance of Nd:LuVO4 crystal

Received August 11, 2003 We report continuous-wave and actively Q-switched laser performance achieved with Nd:LuVO4 crystal for the 4F(3/2) --> 4I(1/2) transition (corresponding wavelength of 1065.8 nm) under high-power diode pumping. Continuous-wave output power of 12.55 W is obtained with an optical conversion efficiency of 50.2%. In actively Q-switched operation the average output power reaches 5.42 W at a pulse repetition frequency of 40 kHz with 18 W of pump power incident upon the crystal, yielding an optical conversion efficiency of 30.1%. The pulse energy and peak power reach 138 microJ and 16.2 kW, respectively, at a pulse repetition frequency of 25 kHz under a pump power of 14.2 W; the pulse duration is 8.5 ns.     

Highly-Efficient Ho:S<Subscript>i</Subscript>Sc<Subscript>2</Subscript>O<Subscript>5</Subscript> Laser Pumped by a Narrow Line-Width Tm:YAP Laser at 1.94 <Emphasis Type="Italic">μ</Emphasis>m

We present a highly-efficient continuous-wave Ho:SSO laser pumped by a diode-pumped Tm:YAP laser with a narrow linewidth (NL) of 0.3 nm. With the free-running (FR) Tm:YAP laser, we obtain a maximum output power of 2.23 W at an absorption pump power of 7.2 W, corresponding to an optical conversion efficiency of 31% and a slope efficiency of 42.6%. With the NL Tm:YAP laser, we obtain a maximum output power of 2.88 W at the same absorption pump power. The optical conversion efficiency increases to 40% when the slope efficiency increases to 55.5%. The output linewidth of the Ho:SSO laser is 0.8 nm when we use the Tm:YAP laser with a narrow linewidth of 1.8 nm pumped by a FR Tm:YAP laser. The beam quality also changes from 1.31 to 1.22.     

An efficient continuous-wave YVO_4/Nd:YVO_4/YVO_4 self-Raman laser pumped by a wavelength-locked 878.9 nm laser diode

We report an efficient continuous-wave self-Raman laser at 1176 nm based on a 20-mm-long composite YVO_4/Nd:YVO_4/YVO_4 crystal and pumped by a wavelength-locked 878.9 nm diode laser.A maximum output power of 5.3 W is achieved at a pump power of 26 W,corresponding to an optical conversion efficiency of 20%and a slope efficiency of 21%.The Raman threshold for the diode pump power was only 0.92 W.The results reveal that in-band pumping by a wavelength-locked diode laser significantly enhances output power and efficiency of self-Raman lasers by virtue of improved pump absorption and relieved thermal loading.     

888nm LD泵浦Nd：LuV04倍频绿光激光器

报道了采用888nIn的激光二极管（LD）泵浦Nd：LuVO4晶体得到1066nm的激光输出,其对应能级跃迁为4F3／2→4I11/2。在注入的泵浦功率为18．2W时,获得了11．3W的近红外1066nm激光输出;然后采用非线性晶体LiB。O。（LBO）进行腔内倍频,获得了533nm的绿激光输出,输出功率为4．3W,其光-光转换效率为23．6％,光束质量因子为M2=1．3,4h功率稳定度优于3．7％。     

双波长Yb∶YAG连续激光理论及实验研究

报道了Yb∶YAG双波长激光振荡阈值的理论结果,实验获得了连续双波长激光输出.实验中,采用紧凑的平凹腔结构、940nm光纤耦合LD端面泵浦方式,Yb∶YAG晶体作为激光晶体,采用10%、15%和20%的输出耦合镜,分别实现了单波长和双波长激光输出,在最高泵浦功率为20 W时,输出耦合率分别为10%、20%,最高获得3.94W的1 050nm激光和3.40 W的1 030nm激光,对应的光光转换效率分别为19.7%和17.0%;当输出耦合率为15%、泵浦功率为11.7 W时,获得0.79 W的双波长激光,对应的光光转换效率为6.8%,功率比为1∶1.3,通过光栅光谱仪测量得到双波长谱线中心分别为1 030.31nm和1 047.50nm;当1 030nm激光功率为3.0 W时,30min内输出功率RMS稳定性优于0.18%.该实验结果与理论分析相吻合,可应用于设计稳定可靠的掺Yb双波长激光器.