用镧系元素(Ⅲ)测定有机化合物中的磷和氟

本文应用14个镧系元素(Ⅲ)对有机化合物中的磷和氟进行了测定,阐明了影响测定的因素。测定的误差:磷为±0.20%,氟为±0.30%。     

元素分析仪法快速测定海洋地质样品中的硫

采用元素分析仪测定海洋沉积物中硫的含量,确定了元素分析仪的最佳工作条件为:氧化炉温度1050℃;载气压力80 kPa;载气流量125 mL/min;加氧量20 mL;氧气分压45 kPa。方法的检出限为0.013%,测定结果的相对标准偏差为1.52%～3.31%(n=12),回收率为97.2%～101.1%。方法可用于沉积物和土壤样品中硫的快速测定。     

ICP-AES法测定AuNiGd合金中的Ni、Gd、Pd、Fe和Bi

报道了采用ICP-AES法测定AuNiGd合金中Ni、 Gd、 Pd、 Fe、 Bi.对测定元素的波长、测定条件进行了选择;考察了基体和无机酸对测定的影响;在优化条件下,对试样进行测定,其相对标准偏差(n＝15) Ni 1.6%、 Gd 1.8%、 Pd 13%、 Fe 4.9%、 Bi 13%;回收率 Ni 98%～105%、 Gd 97%～99%、 Pd 101%～105%、 Fe 98%～104%、 Bi 104%～106%.     

用镧系元素(III)测定有机化合物中的磷和氟

应用14个镧系元素(III)对有机化合物中的磷和氟进行了测定, 阐明了影响测定的因素. 测定的误差:磷为±0.20%,氟为±0.30%.     

电感耦合等离子发射光谱法测定工业碳酸锂中杂质元素

采用电感耦合等离子发射光谱仪,同时测定工业碳酸锂中钾、钠、钙镁等多种元素.回收率在94.7%～106%之间;线性相关系数大于0.999;相对标准偏差在0.01%～0.53%.方法用于实际样品的分析,测定结果与国标方法的测定结果吻合较好.     

电感耦合等离子体质谱法测定水中铀钍元素的含量

建立了电感耦合等离子体质谱测定水中铀钍元素含量的方法。水样以硝酸酸化处理后直接用电感耦合等离子体质谱法测定,为了消除铀记忆效应对测定结果的干扰,测试溶液的质量浓度以不超过10μg/L为宜,样品测定间隙设置清洗时间为2 min。铀钍元素标准曲线线性相关系数分别为0.999 4,0.999 5;铀、钍的检出限分别为0.000 9,0.002 1μg/L;加标回收率分别为95.70%~112.33%,96.94%~109.98%;测定结果的相对标准偏差分别为0.61%~5.33%,1.16%~1.33%。     

HCl沉淀分离-氢化物发生-原子荧光光谱法测定银锭中锑和铋

采用氢化物发生-原子荧光光谱法同时测定银锭中铋和锑。用HCl沉淀分离银,滤液还原后利用氢化物发生-原子荧光光谱法测定铋和锑。方法检出限:Bi和Sb分别为0.02mg/kg和0.002mg/kg;回收率91%～96%;RSD小于1.2%。方法能同时准确测定铋和锑且检出限极低,测定结果与国家标准方法一致。     

氢化物发生原子荧光法同时测定保健品中痕量锗和硒

采用微波消解样品,氢化物发生原子荧光法同时测定保健品中的锗和硒.研究了仪器条件、酸度、 KBH4浓度等对测定的影响,锗和硒的检出限为0.40和0.51 μg/L;相对标准偏差均为2.0%;回收率为77.1%～105.2%和80.0%～108.2%,已用于保健品中锗和硒的测定.     

原子荧光光谱法测定化探样品中的砷和锑

对氢化物原子荧光光谱法测定化探样品中砷和锑元素的分析条件,尤其是浸提法及预还原顺序进行了考察。样品经王水和王水溶液(1+1)分别浸提后以不同顺序预还原,结果表明,王水的氧化性会降低硫脲–抗坏血酸的还原效果,预还原时降低王水浓度能提高测定结果的准确度。在优化的测定条件下,样品中砷、锑测定结果的相对标准偏差分别为0.6%,2.7%;回收率分别为95%～101%,91%～106%;检出限分别为0.020,0.026 ng/mL。改善样品处理方法后测定结果的的准确度得到提高。     

连续流动法同时测定污水中氨氮和总磷

采用连续流动分析法测定污水中氨氮、总磷的含量。比较了污水样品不同的稀释倍数对测定结果的影响。实验结果表明:氨氮和总磷的质量浓度在0.1~8 mg/L范围内线性良好,线性相关系数均为0.99997;测量结果的相对标准偏差分别为2.01%,0.84%(n=7);方法检出限分别为0.012,0.009 mg/L;质控样测量值均在标示值范围内;样品加标回收率为93.4%~101.1%。污水的洁净程度对测定结果影响较大。洁净度高的污水,直接测定与稀释后测定,测定值无显著性差异;而洁净度低的污水,直接测定与稀释后测定结果差异比较大。该法采用全谱直读CCD检测方式,灵敏度高,稳定性好,无光谱干扰,且支持氨氮和总磷同时测定,方便快捷,适合污水中氨氮和总磷的测定。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.