人造玫瑰花花瓣的微结构分布与水滴黏附性质的关系

本文采用模板印刷法制备得到了“人造玫瑰花花瓣”,即具有玫瑰花花瓣结构的PDMS薄膜,通过对该薄膜逐级拉伸改变微观结构的分布;采用环境扫描电镜（ESEM）观察了不同拉伸程度下薄膜表面微观结构的变化,采用高敏感性微电力学天平测试了样品表面微观结构变化过程中水滴的粘附力,分析了微观结构分布与水滴粘附性质的关系;采用接触角测量仪表征不同拉伸条件下薄膜的浸润性.实验结果表明随着PDMS薄膜被逐次拉伸,单位面积内玫瑰花花瓣乳突的数目减少,纳米褶皱面积不断增加,而纳米级褶皱结构尺寸随着拉伸基本上不发生变化,直到样品破坏;与微观结构变化相对应的,该表面对水滴的粘附力先增大后减小,直到该表面彻底破坏.由此可见,微米结构及纳米结构的分布是影响玫瑰花花瓣对水滴粘附的主要因素.     

基于水滴模板法的微纳复合超疏水结构制备的研究

利用粒子辅助水滴模板法的实施获得规则蜂窝状图案化多孔结构模板,并进一步利用聚二甲基硅氧烷(PDMS)复制转移技术获得表面具有微米尺寸蜂窝状突起阵列的反向图案化结构.以这种图案化突起结构作为微米尺寸所提供的微米级粗糙度为基础,设计了2种的简单的二次纳米结构的引入过程,最终实现了微米级阵列和纳米级粗糙度的复合.第一种方法借助银镜反应来实现纳米银结构的化学沉积,最终在PDMS阵列表面获得了致密的纳米银颗粒沉积层,并成功获得了表面接触角达166度的超疏水性质.第二种方法利用了聚电解质/二氧化硅粒子层层静电自组装的方法引入纳米结构,结果在仅仅进行了2个组装循环的条件下即可获得超疏水性质的表面复合结构.通过简单的实验设计试图提供一种基于水滴模板法的微纳复合超疏水结构的普适性制备方法.     

静电纺丝制备具有浸润性梯度的聚酰亚胺纳米纤维膜

采用高压静电纺丝技术, 在非对称异型电极上制备得到放射状聚酰亚胺(PI)纳米纤维膜. 采用环境扫描电子显微镜(ESEM)观察了PI膜的微观形貌以及纳米纤维的排列状态; 采用接触角测量仪研究了水滴浸润性的变化; 采用高敏感性力学微电力学天平测量了水滴的黏附力, 分析了微观形貌变化与水滴浸润性质和黏附性质的关系. 结果表明, 该PI纳米纤维膜沿着非对称异型电极三角电极至弧型电极方向纤维排列由密到疏, 呈放射状, 具有独特的微结构梯度; 整个纤维膜上的PI纳米纤维直径均一且具有光滑均匀表面, 纤维与纤维之间的距离约为几微米到几十微米. 由于PI纳米纤维膜所具有的独特的微结构梯度, 致使沿着微结构梯度方向水滴的接触角(从超疏水到疏水)和黏附力(从低黏附到高黏附)均表现出梯度变化的特征.     

花生叶表面的高黏附超疏水特性研究及其仿生制备

花生是一种常见的豆科作物.与低黏附超疏水的荷叶不同,花生叶表面同时具有超疏水和高黏附特性.水滴在花生叶表面的接触角为151±2°,显示出超疏水特性.此外,水滴可以牢固地附着在花生叶表面,将花生叶翻转90°甚至180°,水滴均不会从表面滚落,显示了良好的黏附性(黏附力超过80μN).研究发现,花生叶表面呈现微纳米多级结构,丘陵状微米结构表面具有无规则排列的纳米结构.花生叶表面特殊的微纳米多尺度结构是其表面呈现高黏附超疏水特性的关键因素.结合实验数据,对花生叶表面特殊浸润性机理进行了简要阐述.受此启发,利用聚二甲基硅氧烷复形得到了与花生叶表面微结构类似的高黏附疏水表面.本文以期为仿生制备高黏附超疏水表面提供新思路.     

喷砂-阳极氧化-氟化处理构筑铝合金超疏水表面

为研究复合法制备超疏水表面过程中主要工艺参数对表面形貌及超疏水性能的影响, 开发了一种喷砂-阳极氧化复合方法, 在铝合金表面构筑了微米-纳米二级结构, 经氟化处理后获得了超疏水特性. 结果表明, 喷砂处理在铝合金表面通过冲蚀的凹坑构筑出微米结构, 阳极氧化则在铝合金表面通过蜂窝状氧化膜构筑纳米结构. 但单纯构筑粗糙结构或单纯改变表面化学组成均不能在铝合金表面获得超疏水特性. 单纯的微米结构或纳米结构, 即使有低表面能聚合物修饰也不能获得超疏水特性. 只有微米-纳米二级结构和低表面能聚合物的协同作用, 才能有效构筑铝合金超疏水表面. 这种铝合金与水滴接触时, 形成的气阱可减小固体表面与水滴的接触面积, 降低表面与水滴间的热量交换, 从而减缓水分子的凝结, 提高铝合金的抗霜冻性. 同时, 气阱还可有效减缓海水的腐蚀, 提高铝合金的耐海水腐蚀性.     

霸王鞭和麒麟掌叶片的表面微结构及超疏水性

霸王鞭(Euphorbia antiquorum)和麒麟掌(Euphorbia neriifolia var. cristata)是2种特殊的叶片, 正面不疏水而叶片背面超疏水的沙漠植物. 本文通过接触角测试仪、 电子显微镜和表面张力测试仪分别对叶片的超疏水性、 表面微观形貌和表面黏附力进行了测试和表征. 采用模板法, 以聚乙烯醇为模板、 以聚苯乙烯为基底制备仿叶片背面结构的聚苯乙烯薄膜, 并对薄膜表面的超疏水性、 表面微观形貌和表面黏附力进行了测试和表征, 发现这2种叶片背面的平均间距为1~3 μm的层片状微观结构可以构建出具有超疏水高黏附力特性的表面.     

软模板印刷法制备超疏水性聚苯乙烯膜

首次利用软模板印刷的方法,以微米-亚微米-纳米复合结构的PDMS为软模板,在平滑聚苯乙烯表面上成功制备了同样具有微米-亚微米-纳米复合结构的超疏水表面,该表面与水的接触角高达161.2º。软模板印刷方法可以用在其它热塑性聚合物如聚丙烯、聚甲基丙烯酸甲酯和聚碳酸酯等材料上,是一种简单有效地制备超疏水性表面的方法。     

超疏水低粘着铜表面制备及其防覆冰性能

用喷砂处理在铜片表面形成微米级丘陵状凹坑,再用表面氧化处理在铜片表面制备菊花花瓣状CuO纳米片.通过喷砂-表面氧化处理在铜片表面成功构建了微米-纳米复合结构,这种表面氟化后与水滴的接触角高达161°,滚动角低至1°,显示出优异的超疏水性和很低的粘着性.低温下,这种表面与水滴间的热量交换较小,水滴不易凝结,有效地提高了抗结霜性.抗结霜性良好的超疏水铜有望在热交换器或低温运行设备等领域获得应用,这种简便的超疏水铜表面的制备方法也给其它工程材料超疏水表面的工业化制备提供了一个思路.     

快速提拉法制备PDMS/SiO2/PDMS-PDA光子弹性体薄膜

采用快速提拉法制备出SiO₂结构色薄膜，将其嵌入到聚二甲基硅氧烷(PDMS)中，然后将掺杂聚多巴胺(PDA)的PDMS(PDMS-PDA)涂覆在SiO₂结构色薄膜表面制备了PDMS/SiO₂/PDMS-PDA光子弹性体薄膜。采用扫描电子显微镜、纳米激光粒度仪、分光光度计、光纤光谱仪、拉力机和手机相机对SiO₂结构色薄膜的微观结构和光学性能以及PDMS/SiO₂/PDMS-PDA薄膜的力致变色性能和力学性能进行了表征。结果表明：SiO₂结构色薄膜为短程有序的非晶光子晶体薄膜，其结构色在漫射光下无角度依赖性，在直射光下有角度依赖性。通过表面涂覆黑色PDMS-PDA层，有效提高了光子弹性体薄膜在拉伸过程中结构色的饱和度，当应变为20%时，薄膜出现明显的结构色，并随着应变的增加反射峰位置不断蓝移。该薄膜具有较好的力学性能，其断裂伸长率达140%。     

双级微结构上二氧化硅粒子对微注压成型PP表面润湿特性的影响

提出一种柔性复制法,采用微注射压缩(μ-ICM)成型具有微拓扑结构的仿生聚丙烯(PP)表面.通过复制模板上的双级微结构,所成型的PP材料表面上呈现具有锥形顶面的双级微结构,即微棱和高纵横比的微锥体.由于微锥体之间的间隙较大,水滴浸润其间隙的上方,这使该表面呈现中等黏附的超疏水特性.在μ-ICM过程中,涂覆在模板上的二氧化硅纳米粒子(SNPs)被转移到熔体中,并牢牢附着于微结构表层,赋予其表面亚微米或微米粗糙度,形成多层次微结构.在附着有亲水SNPs的微结构上,高表面自由能使水滴完全浸润微锥体之间的间隙,表面的水接触角为161.9°、滚动角大于90°,呈现极高黏附的超疏水特性(花瓣效应);在附着有疏水SNPs的微结构上,水滴受疏水SNPs的排斥而减弱与表面之间的黏附作用,表面的水接触角为163.5°、滚动角为3.5°,呈现极低黏附的超疏水特性(荷叶效应).     

Petal effect: a superhydrophobic state with high adhesive force

Hierarchical micropapillae and nanofolds are known to exist on the petals' surfaces of red roses. These micro- and nanostructures provide a sufficient roughness for superhydrophobicity and yet at the same time a high adhesive force with water. A water droplet on the surface of the petal appears spherical in shape, which cannot roll off even when the petal is turned upside down. We define this phenomenon as the "petal effect" as compared with the popular "lotus effect". Artificial fabrication of biomimic polymer films, with well-defined nanoembossed structures obtained by duplicating the petal's surface, indicates that the superhydrophobic surface and the adhesive petal are in Cassie impregnating wetting state.     

超疏水性聚二甲基硅氧烷膜的制备及其表面吸附性研究

采用简单的激光刻蚀方法制备了具有类“菜花”状多级结构的粗糙聚二甲基硅氧烷(PDMS)膜, 并用CCD与高敏感性微电力学天平观察和测量PDMS表面对水的吸附情况. 结果表明, 该膜表面具有超疏水性, 同时对水滴具有超低的吸附力. 还对其表面特殊多级结构产生的机理进行了分析, 并探讨了在化学组成和表面结构对超疏水性以及吸附性产生的影响.     

Application of colloid probe atomic force microscopy to the adhesion of thin films of viscous and viscoelastic silicone fluids

The adhesive characteristics of thin films (0.2-2 μm) of linear poly(dimethylsiloxane) (PDMS) liquids with a wide range of molecular weights have been measured using an atomic force microscope with a colloid probe (diameters 5 and 12 μm) for different separation velocities. The data were consistent with a residual film in the contact region having a thickness of ～6 nm following an extended dwell time before separation of the probe. It was possible to estimate the maximum adhesive force as a function of the capillary number, Ca, by applying existing theoretical models based on capillary interactions and viscous flow except at large values of Ca in the case of viscoelastic fluids, for which it was necessary to develop a nonlinear viscoelastic model. The compliance of the atomic force microscope colloid beam was an important factor in governing the retraction velocity of the probe and therefore the value of the adhesive force, but the inertia of the beam and viscoelastic stress overshoot effects were not significant in the range of separation velocities investigated.     

蝴蝶翅膀表面水滴各向异性黏附性质

采用扫描电子显微镜(SEM)观察了双带闪蝶(Morpho Achilles)翅膀表面的微观形貌, 通过样品的表观接触角表征了其浸润性, 采用高敏感性微电力学天平比较了水滴在蝴蝶翅膀表面不同方向运动时受到的黏附力. 实验结果表明, 水滴沿着干燥的蝴蝶翅膀鳞片堆叠方向运动时受到的黏附力要明显小于其它方向运动时受到的力, 且受力较稳定; 当蝴蝶翅膀被水滴浸润后, 水滴沿着湿润的蝴蝶翅膀鳞片堆叠方向运动时受到的黏附力接近甚至大于逆着鳞片堆叠方向运动时受到的力.     

仿生表面液固界面摩擦力的动态调控

仿生超疏水材料在自清洁、防雾抗冰、油水分离、集水等领域有着重要应用;而在不同疏水状态之间的转换将大大促进仿生超疏水材料在智能技术领域的应用.利用软印刷技术将玫瑰花表面微观结构转印到聚氨酯弹性体PU膜表面,利用机械应力实现表面微结构的动态实时调控,实现了表面微观结构在各向同性与各向异性之间的可逆转换;利用毛细管投影传感技...     

Changes in silicon elastomeric surface properties under stretching induced by three surface treatments

Poly(dimethylsiloxane) (PDMS) substrates are used in many applications where the substrates need to be elongated and various treatments are used to regulate their surface properties. In this article, we compare the effect of three of such treatments, namely, UV irradiation, water plasma, and plasma polymerization, both from a molecular and from a macroscopic point of view. We focus our attention in particular on the behavior of the treated surfaces under mechanical stretching. UV irradiation induces the substitution of methyl groups by hydroxyl and acid groups, water plasma leads to a silicate-like layer, and plasma polymerization causes the formation of an organic thin film with a major content of anhydride and acid groups. Stretching induces cracks on the surface both for silicate-like layers and for plasma polymer thin coatings. This is not the case for the UV irradiated PDMS substrates. We then analyzed the chemical composition of these cracks. In the case of water plasma, the cracks reveal native PDMS. In the case of plasma polymerization, the cracks reveal modified PDMS. The contact angles of plasma polymer and UV treated surfaces vary only very slightly under stretching, whereas large variations are observed for water plasma treatments. The small variation in the contact angle values observed on the plasma polymer thin film under stretching even when cracks appear on the surface are explained by the specific chemistry of the PDMS in the cracks. We find that it is very different from native PDMS and that its structure is somewhere between Si(O2) and Si(O3). This is, to our knowledge, the first study where different surface treatments of PDMS are compared for films under stretching.     

Biomimetic superhydrophobic UHMWPE/nanosilica films with different sticky behavior on several metals

A kind of organic–inorganic composite film with biomimetic superhydrophobic performance was prepared on several metals including steel, aluminum, and copper. The organic matrix was ultrahigh‐molecular‐weight polyethylene (UHMWPE), and the inorganic filler was nanosilica. Scanning electron microscope observation indicated addition of nanosilica greatly changed the topography of the UHMWPE film. Special convexities were formed on the surfaces of the composite films, which made the composite films rougher than that of pure UHMWPE film. The nanosilica randomly scattered on the surface of the convexities and formed hierarchical structure similar to that of some plant leaves with superhydrophobic characteristics. Interestingly, it was found that there were remarkable differences between the sliding angles (SA) of water droplet on the composite films on different metals although the contact angles (CA) of water droplet on these films were quite close. The CA on the composite films on steel was about 157°, and the SA was larger than 90°, which demonstrated obvious superhydrophobic and sticky characteristic. But to the films on aluminum and copper, the CAs on them were larger than 160° and the SAs were between 3° and 4°, which meant excellent superhydrophobic and roll‐off performance. Scanning electron microscope observation indicated that there were some micro‐orifices in the film on steel and these micro‐orifices were connected to some extent. It was believed that these micro‐orifices provided capillary force and restrained sliding of water droplet. A sticky model based on capillary mechanism was proposed. Copyright © 2017 John Wiley & Sons, Ltd.     

Effect of Heat Treatment Temperature on Surface Topography and Hydrophobicity of Polydimethylsiloxane/Titanium Oxide Hybrid Films

Hydrophobic thin films of polydimethylsiloxane (PDMS) - titamium (hydrous) oxide hybrid material were deposited on glass substrate by dip coating from the precursor containing hydroxyl-terminated PDMS and titanium tetraisopropoxide (TIP), as well as small amounts of water and ethyl acetoacetate. Film's hydrophobicity was evaluated by performing contact angle measurement, while surface topography was analyzed by using an atomic force microscope (AFM). Effects of heat treatment temperature and TIP:PDMS ratio on film's hydrophobicity are described.     

Preparation and tribological studies of C60 thin film chemisorbed on a functional polymer surface

A novel self-assembled C60 film was prepared by chemical adsorption of C60 molecules onto an amino-group-containing polyethyleneimine-coated silicon substrate surface. The contact angle of distilled water on the C60 film was measured, the thickness was determined by means of ellipsometric analysis, and the morphology was observed with an atomic force microscope. The tribological properties of the films were investigated as well. It was found that the C60 thin film had a contact angle of about 72 degrees and thickness of 1.8 nm and exhibited a surface domain microstructure composed of fullerene clusters. Due to the hydrophobicity and low surface energy, the C60 film possessed good adhesive resistance and had an adhesive force of about 7.1 nN, which was about an order of magnitude lower than that of the silicon substrate surface. Moreover, the C60 film showed good friction reduction, load-carrying capacity, and antiwear ability, which were attributed to the higher mechanical stiffness and elastic modulus of C60 molecules. Besides, the friction coefficient decreased with increasing sliding velocity and normal loads, due to the rolling effect of the physisorbed C60 molecules.