阵列凹坑结构分布与水滴黏附性质的关系

以新鲜玫瑰花花瓣正面为模板, 采用模板印刷法制备具有微米级阵列凹坑和纳米级沟壑结构的聚二甲基硅氧烷(PDMS)薄膜, 通过对该薄膜逐级拉伸改变其微观结构的分布; 采用场发射扫描电子显微镜(SEM)和原子力显微镜(AFM)观察了不同拉伸程度下薄膜表面微观结构的变化, 采用高敏感性微电力学天平测试了样品表面微观结构变化过程中水滴的黏附力, 分析了其微观结构分布与水滴黏附性质的关系; 采用接触角测量仪表征不同拉伸条件下薄膜的浸润性. 结果表明, 随着PDMS薄膜被逐次拉伸, 单位面积内的凹坑结构数目减少, 且凹坑逐渐分离, 凹坑的深度逐渐降低, 水滴更容易浸入到凹坑结构中, 因此水滴与薄膜的黏附力急剧增大; 随着薄膜进一步拉伸, 纳米级沟壑结构会随着凹坑的拉伸而不断伸展, 纳米级沟壑结构的面积增加, 纳米沟壑结构诱捕的空气量逐渐上升, 导致水滴与薄膜表面的接触面积降低, 使得水滴与薄膜的黏附力下降; 继续拉伸PDMS薄膜, 纳米级沟壑结构进一步伸展, 水滴逐渐浸入纳米级沟壑结构中, 水滴与薄膜的黏附力缓慢增大, 当水滴完全进入到纳米级沟壑中时, 水滴与薄膜的黏附力达到极大值, 此时继续拉伸PDMS薄膜, 纳米级沟壑结构随着拉伸程度的增加继续伸展, 水滴与薄膜的接触面积稍有减少, 黏附力将有所下降, 直至薄膜被完全破坏. 由此可见, 微米级凹坑结构和纳米级褶皱结构的分布是影响PDMS薄膜对水滴黏附性质的主要因素.     

玫瑰花花瓣微观结构与水滴黏附性质的关系

利用环境扫描电镜(ESEM)分别观察了新鲜、枯萎的玫瑰花花瓣正、反两面的微观形貌,并通过测量样品的表观接触角表征了其浸润性,采用高敏感性微电力学天平测试了样品表面的粘附力,分析了玫瑰花花瓣微观结构与水滴粘附性质的关系.实验结果表明,微米结构主要影响玫瑰花花瓣的超疏水性,而纳米结构则是导致玫瑰花花瓣具有高粘附力的关键原因.     

聚苯乙烯/聚二甲基硅氧烷嵌段共聚物的表面形态研究

采用原子力显微镜(AFM)和透射电镜(TEM)研究了聚苯乙烯/聚二甲基硅氧烷嵌段共聚物(PS-b-PDMS)薄膜的相形态.结果表明,当采用甲苯作为溶剂,旋转涂膜的薄膜样品呈现网络状的形态分布在表面,而样品所对应的透射电镜照片中,PDMS相作为球状分布在PS的连续相中.退火温度对共聚物表面形态有一定的影响,当退火温度高于PDMS的玻璃化温度,表面中PDMS相增多.PS-b-PDMS嵌段共聚物的表面形态随着所用溶剂的变化而有所不同,当采用甲苯作为溶剂时,样品的PS相形成凹坑分布在PDMS的相区之中,而采用环己烷作为溶剂时,PS相作为突起分布在PDMS相区之中.另外,基底对共聚物薄膜表面形态的有较大的影响,当采用硅晶片作为基底时,样品中的PDMS相和PS相呈现近似平行于表面的层状结构.     

快速提拉法制备PDMS/SiO2/PDMS-PDA光子弹性体薄膜

采用快速提拉法制备出SiO₂结构色薄膜，将其嵌入到聚二甲基硅氧烷(PDMS)中，然后将掺杂聚多巴胺(PDA)的PDMS(PDMS-PDA)涂覆在SiO₂结构色薄膜表面制备了PDMS/SiO₂/PDMS-PDA光子弹性体薄膜。采用扫描电子显微镜、纳米激光粒度仪、分光光度计、光纤光谱仪、拉力机和手机相机对SiO₂结构色薄膜的微观结构和光学性能以及PDMS/SiO₂/PDMS-PDA薄膜的力致变色性能和力学性能进行了表征。结果表明：SiO₂结构色薄膜为短程有序的非晶光子晶体薄膜，其结构色在漫射光下无角度依赖性，在直射光下有角度依赖性。通过表面涂覆黑色PDMS-PDA层，有效提高了光子弹性体薄膜在拉伸过程中结构色的饱和度，当应变为20%时，薄膜出现明显的结构色，并随着应变的增加反射峰位置不断蓝移。该薄膜具有较好的力学性能，其断裂伸长率达140%。     

静电纺丝制备具有浸润性梯度的聚酰亚胺纳米纤维膜

采用高压静电纺丝技术, 在非对称异型电极上制备得到放射状聚酰亚胺(PI)纳米纤维膜. 采用环境扫描电子显微镜(ESEM)观察了PI膜的微观形貌以及纳米纤维的排列状态; 采用接触角测量仪研究了水滴浸润性的变化; 采用高敏感性力学微电力学天平测量了水滴的黏附力, 分析了微观形貌变化与水滴浸润性质和黏附性质的关系. 结果表明, 该PI纳米纤维膜沿着非对称异型电极三角电极至弧型电极方向纤维排列由密到疏, 呈放射状, 具有独特的微结构梯度; 整个纤维膜上的PI纳米纤维直径均一且具有光滑均匀表面, 纤维与纤维之间的距离约为几微米到几十微米. 由于PI纳米纤维膜所具有的独特的微结构梯度, 致使沿着微结构梯度方向水滴的接触角(从超疏水到疏水)和黏附力(从低黏附到高黏附)均表现出梯度变化的特征.     

超疏水高分子材料表面的微结构设计及其可调的黏附性

采用微注射压缩技术,以单步模板法制备表面具有微结构的大尺寸聚丙烯样品.以2种目数不同的筛网为模板,制备的样品表面呈现由微棱和高纵横比的微锥体构成的双级复合微结构;构建由上述2种筛网与2种孔径不同的冲孔板叠加而成的4种模板,制备的样品表面呈现由均匀分布的微柱和其顶面的上述双级复合微结构构成的三级复合微结构.这6种表面的静态接触角均高于150°(即呈现超疏水特性),滚动角在5.5°至大于90°之间变化(即黏附性可在大范围内调节).对在直径较小的微柱上成型数量较少的微锥体和微棱的表面,水滴形成全局非复合润湿状态,从而呈现高粘附特性(花瓣效应);对在直径较小的微柱上成型数量较多的微锥体和微棱的表面,水滴形成局部非复合润湿状态,呈现较高粘附特性;对呈现双级复合微结构或在直径较大的微柱上成型数量较多的微锥体和微棱的表面,水滴形成全局复合润湿状态,呈现较低粘附特性,其中微锥体及其间隙较小的表面呈现荷叶效应.     

基于水滴模板法的微纳复合超疏水结构制备的研究

利用粒子辅助水滴模板法的实施获得规则蜂窝状图案化多孔结构模板,并进一步利用聚二甲基硅氧烷(PDMS)复制转移技术获得表面具有微米尺寸蜂窝状突起阵列的反向图案化结构.以这种图案化突起结构作为微米尺寸所提供的微米级粗糙度为基础,设计了2种的简单的二次纳米结构的引入过程,最终实现了微米级阵列和纳米级粗糙度的复合.第一种方法借助银镜反应来实现纳米银结构的化学沉积,最终在PDMS阵列表面获得了致密的纳米银颗粒沉积层,并成功获得了表面接触角达166度的超疏水性质.第二种方法利用了聚电解质/二氧化硅粒子层层静电自组装的方法引入纳米结构,结果在仅仅进行了2个组装循环的条件下即可获得超疏水性质的表面复合结构.通过简单的实验设计试图提供一种基于水滴模板法的微纳复合超疏水结构的普适性制备方法.     

蝴蝶翅膀表面水滴各向异性黏附性质

采用扫描电子显微镜(SEM)观察了双带闪蝶(Morpho Achilles)翅膀表面的微观形貌, 通过样品的表观接触角表征了其浸润性, 采用高敏感性微电力学天平比较了水滴在蝴蝶翅膀表面不同方向运动时受到的黏附力. 实验结果表明, 水滴沿着干燥的蝴蝶翅膀鳞片堆叠方向运动时受到的黏附力要明显小于其它方向运动时受到的力, 且受力较稳定; 当蝴蝶翅膀被水滴浸润后, 水滴沿着湿润的蝴蝶翅膀鳞片堆叠方向运动时受到的黏附力接近甚至大于逆着鳞片堆叠方向运动时受到的力.     

利用胶体探针技术研究多巴与纳米、微米及微纳复合结构表面之间的相互作用

通过在硅片表面有机蒸镀不同厚度的二十九烷制备了不同晶体密度的仿生旱金莲叶面蜡质纳米结构表面,采用端基修饰多巴的原子力显微镜胶体探针,对各纳米结构表面进行了粘附性能测试,发现蒸镀200 nm厚度二十九烷结晶的纳米结构表面具有较低粘附力。采用反应离子刻蚀方法制备了不同高度的硅材质仿生鲨鱼皮微米结构表面,并选择了200 nm厚度二十九烷在仿生鲨鱼皮表面进行有机蒸镀制备了微纳复合结构表面,通过胶体探针的研究发现多巴与高度为1、3、5μm微纳复合结构表面的粘附力均小于与200 nm厚度二十九烷结晶的纳米结构表面之间的粘附力,说明微纳复合结构表面具有很强的抗多巴粘附能力,并且这种复合结构表面相对于硅材质的仿生鲨鱼皮微米结构表面还兼有旱金莲叶面的强疏水性和极佳的抗水粘附能力。     

溶胶凝胶法制备仿生超疏水性薄膜

通过溶胶-凝胶(Sol-Gel)法和自组装(Self-assembled)制备了具有超疏水性的薄膜, 水滴在该薄膜上的平衡静态接触角为155°～157°, 滑动角为3°～5°. 通过扫描电子显微镜(SEM)观察薄膜微观表面, 发现该薄膜表面分布了双层结构(Binary structure)的微纳米粗糙度的微凸体, 上表层微米微凸体的平均直径为0. 2 μm, 下表层纳米微凸体的平均直径约为13 nm, 其分布与荷叶表面的结构极其相似. 用X射线光电子能谱(XPS)对薄膜表面元素进行了成分分析, 结果表明, 其表面存在大量的F, Cl等元素, 它能显著降低薄膜表面的表面能. 薄膜超疏水性的原因可能是, 通过硅片经溶胶粒子表面制备的薄膜具有合适的表面粗糙度, 再经过全氟辛基三氯甲硅烷(FOTMS)化学修饰后, 薄膜表面能进一步降低, 这两个条件的有机结合就使得薄膜产生了超疏水性.     

Petal effect: a superhydrophobic state with high adhesive force

Hierarchical micropapillae and nanofolds are known to exist on the petals' surfaces of red roses. These micro- and nanostructures provide a sufficient roughness for superhydrophobicity and yet at the same time a high adhesive force with water. A water droplet on the surface of the petal appears spherical in shape, which cannot roll off even when the petal is turned upside down. We define this phenomenon as the "petal effect" as compared with the popular "lotus effect". Artificial fabrication of biomimic polymer films, with well-defined nanoembossed structures obtained by duplicating the petal's surface, indicates that the superhydrophobic surface and the adhesive petal are in Cassie impregnating wetting state.     

Wear-resistant rose petal-effect surfaces with superhydrophobicity and high droplet adhesion using hydrophobic and hydrophilic nanoparticles

Surfaces exhibiting the so-called "petal effect" (superhydrophobicity with high droplet adhesion) have potential for applications such as the transport of small volumes of liquid. It is known that the microstructure pitch value and nanostructure density are important in achieving this effect, both in rose petals themselves and in synthetic petal-effect surfaces. However, the effect of the surface energy of materials on these values has not been systematically studied. In addition, wear resistance, which is critical for industrial applications, has rarely been examined for petal-effect surfaces. In this study, surfaces of varying microstructure pitch and nanostructure density were fabricated by depositing ZnO nanoparticles onto micropatterned substrates. The prepared surfaces were then modified with octadecylphosphonic acid (ODP) in order to hydrophobize the ZnO nanoparticles. The wettability of the surfaces was characterized both before and after ODP modification. The effect of hydrophobizing the nanostructure was examined with regards to the values of microstructure pitch and nanostructure density necessary to achieve the petal effect. In addition, to study wear resistance for industrial applications, a wear experiment was performed using an atomic force microscope (AFM).     

Fabrication and characterization of hierarchical nanostructured smart adhesion surfaces

The mechanics of fibrillar adhesive surfaces of biological systems such as a Lotus leaf and a gecko are widely studied due to their unique surface properties. The Lotus leaf is a model for superhydrophobic surfaces, self-cleaning properties, and low adhesion. Gecko feet have high adhesion due to the high micro/nanofibrillar hierarchical structures. A nanostructured surface may exhibit low adhesion or high adhesion depending upon fibrillar density, and it presents the possibility of realizing eco-friendly surface structures with desirable adhesion. The current research, for the first time uses a patterning technique to fabricate smart adhesion surfaces: single- and two-level hierarchical synthetic adhesive structure surfaces with various fibrillar densities and diameters that allows the observation of either the Lotus or gecko adhesion effects. Contact angles of the fabricated structured samples were measured to characterize their wettability, and contamination experiments were performed to study for self-cleaning ability. A conventional and a glass ball attached to an atomic force microscope (AFM) tip were used to obtain the adhesive forces via force-distance curves to study scale effect. A further increase of the adhesive forces on the samples was achieved by applying an adhesive to the surfaces.     

Hierarchical assembly of micro-/nano-building blocks: bio-inspired rigid structural functional materials

The huge diversity of hierarchical micro-/nano-rigid structures existing in biological systems is increasingly becoming a source of inspiration of materials scientists and engineers to create next-generation advanced functional materials. In the past decades, these multiscale hierarchical structures have been intensively investigated to show their contributions to high performance in mechanical properties. Recently, accompanied with the development of nanotechnology, some biologically hierarchical rigid structures have been duplicated and mimicked in artificial materials through hierarchical organization of micro-/nano-building blocks. In this critical review, we will present biological rigid structural models, functional micro-/nano-building blocks, and hierarchical assembly techniques for the manufacture of bio-inspired rigid structural functional materials (177 references).     

花生叶表面的高黏附超疏水特性研究及其仿生制备

花生是一种常见的豆科作物.与低黏附超疏水的荷叶不同,花生叶表面同时具有超疏水和高黏附特性.水滴在花生叶表面的接触角为151±2°,显示出超疏水特性.此外,水滴可以牢固地附着在花生叶表面,将花生叶翻转90°甚至180°,水滴均不会从表面滚落,显示了良好的黏附性(黏附力超过80μN).研究发现,花生叶表面呈现微纳米多级结构,丘陵状微米结构表面具有无规则排列的纳米结构.花生叶表面特殊的微纳米多尺度结构是其表面呈现高黏附超疏水特性的关键因素.结合实验数据,对花生叶表面特殊浸润性机理进行了简要阐述.受此启发,利用聚二甲基硅氧烷复形得到了与花生叶表面微结构类似的高黏附疏水表面.本文以期为仿生制备高黏附超疏水表面提供新思路.     

Creation of “Rose Petal” and “Lotus Leaf” Effects on Alumina by Surface Functionalization and Metal‐Ion Coordination

Functional differences between superhydrophobic surfaces, such as lotus leaf and rose petals, are due to the subtle architectural features created by nature. Mimicry of these surfaces with synthetic molecules continues to be fascinating as well as challenging. Herein, we demonstrate how inherently hydrophilic alumina surface can be modified to give two distinct superhydrophobic behaviors. Functionalization of alumina with an organic ligand resulted in a rose‐petal‐like surface (water pinning) with a contact angle of 145° and a high contact angle hysteresis (±69°). Subsequent interaction of the ligand with Zn²⁺ resulted in a lotus‐leaf‐like surface with water rolling behavior owing to high contact angle (165°) and low‐contact‐angle‐hysteresis (±2°). In both cases, coating of an aromatic bis‐aldehyde with alkoxy chain substituents was necessary to emulate the nanowaxy cuticular feature of natural superhydrophobic materials.     

仿花瓣表面多功能高分子纳米薄膜的制备

以红玫瑰花瓣为模板, 用纳米压印图案转移法进行仿生合成, 获得具有多功能性的高分子薄膜. 通过将薄膜进行染色, 制得了具有特殊花瓣颜色的人工薄膜, 并探讨了化学色与结构色之间的关系.