Cr2O3气相催化1,1,2-三氯乙烷脱HCl性能

采用沉淀法制备了不同焙烧温度的Cr₂O₃催化剂,用于1,1,2-三氯乙烷(TCE)气相脱氯化氢制备二氯乙烯的反应。 采用X射线衍射(XRD)、氢气程序升温还原(H₂-TPR)、氨气程序升温脱附(NH₃-TPD)、X射线光电子能谱(XPS)表征手段,研究了Cr₂O₃催化剂气相催化裂解TCE脱氯化氢反应及其反应机理。 结果表明,Cr₂O₃催化剂上TCE气相脱氯化氢反应的转化率随着催化剂焙烧温度的升高逐渐降低,然而顺-1,2-二氯乙烯(cis-DCE)的选择性先增大后减小。 400 ℃焙烧的Cr₂O₃催化剂催化性能最好,TCE转化率为70.8%,顺-1,2-二氯乙烯的选择性为90.0%。 然而,催化剂的单位面积反应速率随着焙烧温度升高先提高后下降,400 ℃焙烧催化剂的单位面积反应速率为0.801×10^-2 μmol/(s·m²)。 催化剂的单位面积反应速率和顺-1,2-二氯乙烯(cis-DCE)的选择性与催化剂表面Cr₂O₃物种具有很好的对应关系,表明催化剂表面Cr₂O₃物种有利于脱氯化氢反应。 以酸中心为活性中心计算得到的转换频率(TOF)变化趋势与单位面积反应速率相一致,400 ℃焙烧的催化剂的TOF为2.82×10^-5 s^-1,表明Cr₂O₃催化剂Cr物种合适的平均价态(~3.20)有利于脱氯化氢反应。     

2-(4-咔唑-1-基-苯基)-1H-苯并咪唑的合成及其光学性质

以邻苯二胺与4-(咔唑-1-基)苯甲醛为原料,合成了一种新型苯并咪唑衍生物--2-(4-咔唑-1-基-苯基)-1H-苯并咪唑(2),其结构经¹H NMR, ¹³C NMR, MS（ESI), IR和元素分析表征。通过理论计算,结合UV-Vis和单光子荧光光谱研究了其光学性质,结果表明：2在二氯甲烷,乙酸乙酯,乙醇,乙腈和DMF中的λ_max均位于292 nm和330 nm 附近, λ_em分别为389 nm, 379 nm, 395 nm, 400 nm和390 nm。     

层状苯膦酸-磷酸锆的合成与磺化研究

研究了制备苯膦酸-磷酸锆Zr(PO₄H)_2-n(PO₃Ph)_n的主要影响因素。在F^-/Zr⁴⁺=12和H₃PO₄/Zr⁴⁺=20条件下,通过改变苯膦酸用量获得了n=0～2的系列单一晶相层状苯膦酸-磷酸锆,其热稳定性达400℃以上。苯膦酸-磷酸锆的磺化试验表明层间苯环可被完全磺化,磺化产物Zr(PO₄H)_2-n(PO₃PhSO₃H)_n具有丰富的酸性位,其热稳定性亦可达到300℃以上。     

5,10,15,20-四(2-噻吩基)金属卟啉修饰TiO2光催化剂的制备及光催化性能

合成了5,10,15,20-四(2-噻吩基)卟啉(H₂TTP)及它的钴铜锌三种金属卟啉, 并用上述三种金属卟啉分别敏化锐钛矿型的二氧化钛, 制备了CoTTP-TiO₂, ZnTTP-TiO₂, CuTTP-TiO₂三种光催化剂, 对这三种光催化剂进行了扫描电镜(SEM)、X射线光电子能谱(XPS)、紫外-可见漫反射光谱(UV-vis)、红外光谱(IR)的表征. 在300 W汞灯和400 W金卤灯照射下, 制备的光催化剂对4-硝基苯酚溶液的降解表现出比未修饰二氧化钛高的催化效率, 光催化降解反应符合反应一级动力学方程.     

鲁米诺-二甲亚砜-氢氧化钠体系化学发光机理的理论研究

用密度泛函理论(DFT) B3PW91/6-31G**方法研究了鲁米诺-二甲亚砜-氢氧化钠化学发光反应体系中反应物、中间体和产物的分子结构和振动频率, 用B3PW91/6-311＋G(3df,2p)方法获得反应能量以及用时间相关(Time Dependent, TD)的B3PW91/6-311＋G(3df, 2p)方法进行电子激发能态分析. 研究结果支持了下列化学发光反应通道: LH₂(¹A)＋OH^－ →LH₂•OH^－(¹A)→LH^－(¹A)→L^·－(²A)→TS₁(³A)→LO₂^2－(³A)→TS₂(³A)→AP^2－*(?³A)→AP^2－(X³A)＋hν, 最后即AP^2－*回到基态发光; 或AP^2－*(?³A)→AP^2－*(?¹A)→AP^2－(a¹A)＋hν, 即激发态势能面交叉后的单重态跃迁发光. 它们在可见光区域主要有400～460和500～530 nm的强吸收谱带, 与实验结果符合. 研究还表明, 质子化的鲁米诺能量将大幅度降低, 说明酸性溶液导致鲁米诺的反应活性降低, 从理论上解释了鲁米诺化学发光体系的溶液须呈碱性, pH值影响发光反应的实验事实.     

有机锡9-芴酮-4-甲酸酯的合成、结构及抗癌活性

合成了3个有机锡9-芴酮-4-甲酸酯:三苯基锡9-芴酮-4-甲酸酯[(C₆H₅)₃Sn(C₁₄H₇O₃)](1)、三环己基锡9-芴酮-4-甲酸酯[(C₆H₁₁)₃Sn(C₁₄H₇O₃)](2)和三(2-甲基-2-苯基丙基)锡9-芴酮-4-甲酸酯[(C₆H₅C(CH₃)₂CH₂)₃Sn(C₁₄H₇O₃)](3)。通过元素分析、红外光谱、核磁共振谱(¹H、¹³C和¹¹⁹Sn)、热重分析进行了表征;用单晶X射线衍射方法测定了化合物的晶体结构,并对其进行了量子化学计算和体外抗...     

5-羟基嘧啶——Ⅳ.5-烷氧基-5-烷基-2-硫代巴比酸和有关化合物的合成

自烷氧基乙酸乙酯的乙氧草酰化,继以热裂去羰化反应,合成了一系列烷氧基丙二酸二乙酯(Ⅵ,R=n-C₃H₇,n-C₄H₉,iso-C₄H₉,iso-C₅H₁₁和C₆H₅CH₂);进一步烷基化,得到烷氧基烷基丙二酸二乙酯(Ⅶ,R'=CH₃,C₂H₅,n-C₃H₇和n-C₄H-9)。烷氧基烷基丙二酸二乙酯(Ⅶ)与脲、硫脲和与胍的缩合的容易程度相差颇巨。除苯甲氧基乙基丙二酸二乙酯曾与脲缩合生成相应的5,5-二取代巴比酸(I,Y=O)外,其他的各烷氧基烷基丙二酸二乙酯(Ⅶ)均未能与脲顺利地发生缩合。各烷氧基烷基丙二酸二乙酯(Ⅶ)与硫脲的缩合效果较佳,但其中仍有若干未能得到所期望的2-硫代巴比酸(I,Y=S)。两个系列的烷氧基烷基丙二酸二乙酯(Ⅶ,R=n-C₃H₇和C₆H₅CH₂;R'=CH₃,C₂H₅,n-C₃H₇,和n-C₄H₉)与胍的缩合非常顺利,生成相应的5,5-二取代-2-亚氨基巴此酸(I,Y=NH)。5-苯甲氧基-5-烷基-2-亚氨基巴比酸还进行了氢解,得到相应的5-羟基-5-烷基-2-亚氰基巴比酸(I,R=H,R'=烷基,Y=NH)。     

Fe(Ⅱ)/2-酮戊二酸依赖型双加氧酶重组大肠杆菌全细胞催化合成4-羟基异亮氨酸

以L-异亮氨酸(L-ILe)为底物, 以异源表达Fe(Ⅱ)/2-酮戊二酸依赖型双加氧酶的重组大肠杆菌BL21/pET28a-ido全细胞作为催化剂, 催化合成4-羟基异亮氨酸(4-HIL). 基于重组异亮氨酸双加氧酶(IDO)催化异亮氨酸羟基化的性质和条件, 在摇瓶水平上对辅因子亚铁离子、 α-酮戊二酸(α-KG)及底物浓度进行了单因素优化. 获得的最佳反应条件为2 g/L FeSO₄·7H₂O, 底物与α-KG摩尔比为1∶1, 该条件下反应8 h可生成190 mmol/L 4-HIL. 结合摇瓶水平的最优条件, 在反应器水平上继续对搅拌速度、 菌体浓度等进行优化, 实现了对高底物浓度下催化反应的连续调控. 在50 g/L湿菌体及400 r/min转速下可一次转化合成400 mmol/L 4-HIL, 建立了全细胞催化合成4-羟基异亮氨酸的工艺流程.     

4,7,10-三(叔丁氧碳酰甲基)-1,4,7,10-四氮杂环十二烷-1-乙酰肼的微波合成

以轮环藤宁为起始原料,依次与溴乙酸叔丁酯,溴乙酸乙酯和水合肼反应合成了一种核磁共振对比剂螯合前体--4,7,10-三(叔丁氧碳酰甲基)-1,4,7,10-四氮杂环十二烷-1-乙酰肼（4）,其结构经¹H NMR, ¹³C NMR, FT-IR和MS(ESI)表征。研究了溶剂、水合肼用量、微波功率和反应时间对4收率的影响。结果表明：乙醇为溶剂,水合肼10 eq.,于400 W微波反应10 min, 4（粉末固体）收率90%。     

1-(芘-1-基)-3-(4-甲氧基苯基)丙烯酮的合成及三阶非线性光学性质

合成了一种新的有机非线性光学(NLO)材料1-(芘-1-基)-3-(4-甲氧基苯基)丙烯酮(PMPAK),通过¹H NMR、IR、HR-MS和元素分析表征其结构。 以Nd:YAG-Laser System作为光源,激光波长450 nm,脉冲宽度4 ns(FWHM),采用4f相位相干成像技术测定了PMPAK的三阶NLO性质并确定了相关参数:非线性折射率n₂=-1.84×10^-16 m²/W,非线性吸收系数β=2.53×10^-9 m/W,非线性极化率χ⁽³⁾=1.137×10^-10 esu。     

直接甲醇燃料电池性能

采用商品Pt-Ru/C和Pt/C催化剂制备成甲醇阳极和氧阴极,Nafion-115为固体电解质膜,组装成面积为9cm^2单电池,研究了电池在放电运转过程中各种操作条件,如温度、氧气压力,甲醇浓度等对电池性能的影响,并考察了电池室温放电性能随时间的变化,发现增加电池的温度和 氧气压力均可明显提高电池性能,在合适的甲醇学及氧气压力下电池在室温具有一定的稳定放电性能。     

娃儿藤碱类似物DCB-3501的全合成及其细胞毒性

以3,4-二甲氧基苯甲醛与3,4-二甲氧基苯乙酸为起始原料,经Perkin缩合、自由基氧化偶联反应、Swern氧化、还原胺化及付克酰基化等7步反应全合成了娃儿藤碱类似物DCB-3501,其结构经¹H NMR和ESI-MS确证。体外细胞毒性测试结果表明：DCB-3501对人结肠癌细胞HCT116、人胃癌细胞BGC-823、人肝癌细胞HepG-2、人宫颈癌细胞HeLa和人大细胞肺癌细胞H460的IC₅₀分别为20.0 μmol·L^-1, 50.9 μmol·L^-1, 2.1 μmol·L^-1, 65.8 μmol·L^-1和30.8 μmol·L^-1。     

Preferential cytotoxicity for multidrug-resistant K562 cells using the combination of a photosensitizer and a cyanine dye

The cyanine dye 1,1',3,3,3',3'-hexamethylindodicarbocyanine iodide (HIDC) protects K562 leukemia cells from photodynamic membrane damage caused by cis-di(4-sulfonatophenyl)diphenylporphine (TPPS2) and 420 nm light. This wavelength of light is chosen because it is absorbed by TPPS2, but not by HIDC. The photodynamic system studied may be useful as a model for antineoplastic therapy. A subline of K562 leukemia (K562/DOX), expressing the multidrug-resistance (MDR) phenotype, is found to accumulate smaller amounts of HIDC than the parent cell line and thus has less photoprotection. In the absence of added HIDC, the K562/DOX cell line is more resistant to photodynamic cytotoxicity than the K562 cell line. The resistance of the K562/DOX cell line is not due to a smaller accumulation of TPPS2 than the K562 cell line. However, when both cell lines are incubated with HIDC and TPPS2, and then exposed to light, the K562/DOX cell line becomes more sensitive to photodynamic cell damage than the K562 cell line. The combination of a photosensitizer with a cationic or lysomorphotropic photoprotector represents a novel strategy for the eradication of malignant cells expressing the MDR phenotype.     

n—型聚乙炔复合膜电极性能的研究

自MacDiarmid等将聚乙炔(PA)做为二次电池的电极材料以来,其电化学特性和行为引起了人们的极大兴趣.随后的研究表明,p-型PA[(CH)~(y )Ay~-]_x在电解液中不稳定,用ClO_4~-掺杂的PA充放循环时有降解发生.n-型PA[My~ (CH)~(y-)]_x(y≤0.10)在THF/LiClO_4电解质中较稳定,电化学还原完全可逆,目前已实现1100次充放循环.因此,它既可做电池的正极材料(碱金属为负极),又可做负极材料(TiS_2为正极).我们发现     

细胞不同代谢类型的量热学研究 I.静息细胞有氧非生长代谢特征

The metabolic heat output of resting cells (Saccharobacter fermentatus WVB8512) has been determined by means of microcalorimetric method. The metabolic thermokinetic equation is
dp/dt=k0,k0=0
The thermochemical equations are
lntm=10.1812-6.5492×10-9C
dC/dP0=KCn n=2
The order of metabolism (n) is 2. The experimental results indicate that the heat output produced by each cell and the metabolic time depend on cell concentration and are inhibited by cell density. The metabolism presents a special kind of special inhibition effect.     

PHOTODYNAMIC THERAPY WITH PHOTOFRIN II INDUCES PROGRAMMED CELL DEATH IN CARCINOMA CELL LINES

Abstract The mode of cell death following photodynamic therapy was investigated from the perspective of programmed cell death or apoptosis. Human prostate carcinoma cells (PC3), human non-small cell lung carcinoma (H322a) and rat mammary carcinoma (MTF7) were treated by photodynamic therapy. An examination of extracted cellular DNA by gel electrophoresis showed the characteristic DNA ladder indicative of internucleosomal cleavage of DNA during apoptosis. The magnitude of the response and the photodynamic therapy dosage required to induce DNA fragmentation were different in PC3 and MTF7. The MTF7 cells responded with rapid apoptosis at the dose of light and drug that yielded 50% cell death (LD₅₀). In contrast, PC3 showed only marginal response at the LD₅₀ but had a marked response at the LD₈₅. Thus, apoptosis did not ensue as quickly in PC3 as in MTF7. The H322a cells were killed by photodynamic therapy but failed to exhibit any apoptotic response. The results also suggested that apoptosis in these cell lines has a minor requirement for de novo protein synthesis and no requirement for de novo RNA synthesis. This study indicates that although apoptosis can occur during photodynamic therapy-induced cell death, this response is not universal for all cancer cell lines.     

Electrical impedance spectroscopy for detection of bacterial cells in suspensions using interdigitated microelectrodes

In this study, we present a new, simple and rapid impedance method to detect bacterial cells by making use of the impedance properties of bacterial cell suspensions using interdigitated microelectrodes. It was found that bacterial cell suspensions in deionized (DI) water with different cell concentrations could generate different electrical impedance spectral responses, whereas cell suspensions in phosphate buffered saline (PBS) solution could not produce any significant differences in impedance spectra in response to different cell concentrations. In DI water suspensions, impedance at 1 kHz decreased with the increasing cell concentrations in the suspensions. The impedance of cell suspensions in DI water was discussed and found that it was resulted from the cell wall charges and the release of ions or other osmolytes from the cells. A linear relationship between the impedance and the logarithmic value of the cell concentration was found in the cell concentration range from 10⁶ to 10¹⁰ cfu/ml, which can be expressed by a regression equation of Z (kΩ) = −2.06 log C (cells/20 μl) + 5.23 with R² = 0.98. The detection limit was calculated to be 3.45 × 10⁶ cfu/ml, which is comparable with many label-free immunosensors for detection of pathogenic bacteria reported in the literature. To achieve the selectivity of this method, we also demonstrated the feasibility of integrating magnetic separation to this impedance method. This study has demonstrated that bacterial cell concentration can be inferred by measuring the impedance of cell suspensions in DI water. This new detection mechanism could be an alternative to current impedance methods that have been reported for the detection of bacterial cells, e.g. impedance microbiology and electrical/electrochemical impedance biosensors.     

Surface characteristic and cell response of CVD SiC coating for carbon/carbon composites used for hip arthroplasty

SiC coatings were applied on carbon/carbon composites by chemical vapor deposition for potential application in hip arthroplasty. The surface morphology, roughness, and wettability of the coatings were evaluated by scanning electron microscopy, laser confocal scanning microscope, and video‐based contact angle measuring device, respectively. The bonding strength between the coatings and carbon/carbon composites was analyzed by scratch testing. The cell responses to coatings were studied by analyzing the cell morphology and cell proliferation. The results showed that SiC coatings showed spherical morphology with a roughness of R_a = 1.0 ± 0.2 µm and a contact angle of 64.7 ± 4.0°. The coatings had lower surface roughness and better surface hydrophilicity compared with those of the uncoated carbon/carbon composites. A strong shear strength averaging 120.0 MPa between the coating and carbon/carbon composites was achieved. The cell culture experiments showed that cell spreading was improved, and cell proliferation was increased with the SiC coatings. It was demonstrated that CVD‐SiC‐coated carbon/carbon composites were good candidates as artificial hip joint materials. Copyright © 2012 John Wiley & Sons, Ltd.     

Kinetics study of oil sorption with open‐cell polypropylene/polyolefin elastomer blend foams prepared via continuous extrusion foaming

The objective of the present work was to study the sorption kinetics of open‐cell polypropylene/polyolefin elastomer (PP/POE) blend foams. First, open‐cell PP/POE foams of different cell structures were prepared by controlling the foaming temperature via a continuous extrusion foaming process. Second, the effect of the cell structures on the sorption process, rate, and capacity was studied. Pseudo‐first order and pseudo‐second order models were applied to study the sorption kinetics of the PP/POE foams for cyclohexane. Third, the sorption rate and sorption capacity by both volume and weight of the PP/POE foam for different oils and solvents were studied to show how the intrinsic properties of the testing oils and solvents affected the sorption performance. The results showed that the sorption with the PP/POE foams followed the pseudo‐second order kinetics model. Both the cell structures of the foams and the intrinsic properties of the testing oils and solvents affected the sorption performance. For the same testing oil, a higher open‐cell content in the foam was favorable for a higher sorption rate, and a higher void fraction was favorable for a higher sorption capacity. For the same foam, a lower viscosity of the testing oil was favorable for a higher sorption rate. The sorption capacity by volume was closely related to the viscosity of the testing oil, while both the viscosity and the density of the testing oil determined the sorption capacity by weight.     

Effect of Supercritical Carbon Dioxide Conditions on PVDF/PVP Microcellular Foams

Supercritical carbon dioxide (ScCO₂) was used as a physical foaming agent to prepare poly(vinylidene f luoride)/poly(N-vinyl pyrrolidone) (PVDF/PVP) microstructure material. The effects of foaming conditions including saturation pressure, foaming temperature and foaming time on PVDF/PVP foams morphology, thermal and electrical behavior were systematically investigated by scanning electron microscope, differential scanning calorimeter and broadband dielectric spectrometer. Small cell and low cell density were achieved at low pressure of 12 MPa, as increasing saturation pressure, the average cell size increased first, and then decreased. The competition between the cell growth and cell nucleation played an important role in average cell size, which was directly related to ScCO₂ processing conditions. With increasing foaming temperature, cell size was increased and cell density was decreased, in a nearly linear manner. The variation of foaming time was considered to be closely related to the time for cells to grow. Thus, the results revealed that the average cell size enhanced with extending foaming time. The thermal properties of PVDF/PVP composites are slightly inf luenced by foaming parameters, and the dielectric constant of PVDF/PVP composite foams decreased with increasing volume expansion ratio.