工作气压对磁控溅射ZnO薄膜结晶特性及生长行为的影响

采用射频反应磁控溅射方法，在Si(001)基片上制备了具有高c轴择优取向的ZnO薄膜.利用原子力显微镜、X射线衍射、透射电子显微镜和透射光谱分析技术，对不同工作气压下合成的ZnO薄膜的表面形貌、微观结构和光学性能进行表征，研究了工作气压对ZnO薄膜的结晶性能以及生长行为的影响.研究结果显示：对于Ar/O₂流量比例接近1∶1的固定比值下，ZnO薄膜的生长行为主要取决于成膜空间中氧的密度，临界工作气压介于0.5—1.0 Pa之间.当工作气压小于临界值时，ZnO薄膜的成核密度较高，且随工作气压的变化明显，ZnO的生长行为受控于氧的密度，属于氧支配的薄膜生长；当工作气压大于临界值以后，ZnO薄膜的成核密度基本保持不变，Zn原子的数量决定薄膜的生长速率；在0.1—5.0 Pa的工作气压范围内，均可获得高度c轴取向的ZnO薄膜，但工作气压的变化改变着ZnO晶粒之间的界面特征和取向关系.随着工作气压的增加，ZnO晶粒之间的界面失配缺陷减少，但平面织构特征逐渐消失，三叉晶界的空洞逐渐扩大，薄膜的密度下降，折射率减小. 关键词： ZnO薄膜 磁控溅射 表面形貌 微观结构 光学性能     

温度对ZnO/Al2O3(0001)界面的吸附、扩散及生长初期模式的影响

构建了一个ZnO沉积在α-Al₂O₃(0001)表面生长初期的模型，采用基于密度泛函理论的平面波超软赝势法进行了动力学模拟.发现在400，600和800℃的条件下界面原子有不同的扩散能力，因此温度对ZnO/α-Al₂O₃(0001)表面界面结构以及ZnO薄膜生长初期模式有决定性的影响.在整个ZnO吸附生长过程中，O原子的扩散系数大于Zn原子的扩散系数，O原子的层间扩散对薄膜的均匀生长起着重要作用.进一步从理论计算上证实了ZnO在蓝宝石(0001)上两种生长模式的存在，400℃左右生长模式主要是Zn螺旋扭曲生长，具有Zn六角平面对称特征，且有利于Zn原子位于最外表面.600℃左右呈现为比较规则的层状生长，且有利于O原子位于最外表面.模拟观察到在ZnO薄膜临近Al₂O₃基片表面处，Zn的空位缺陷明显多于O的空位缺陷. 关键词： 扩散 薄膜生长 2O₃(0001)')" href="#">α-Al₂O₃(0001) ZnO     

H2， He混合稀释生长微晶硅锗薄膜

采用H₂,He混合气体稀释等离子辅助反应热化学气相沉积法生长微晶硅锗薄膜,并在生长过程中对等离子体进行光发射光谱在线监测.结果表明：混合气体稀释法可以有效提高等离子体中的原子氢数目,降低等离子体中的电子温度;用XRD和光暗电导率表征样品的微结构和光电特性时发现,通过优化混合稀释气体中He和H₂气体的比例,能够减少薄膜中的缺陷态,促进薄膜<220>择优取向生长,有效改善微晶硅锗薄膜结构,提高光电吸收性能. 关键词： 化学气相沉积 微晶硅锗薄膜 光发射光谱 X射线衍射     

磁控溅射ZnO薄膜的成核机制及表面形貌演化动力学研究

利用原子力显微镜分析了ZnO薄膜在具有本征氧化层的Si(100)和Si(111)基片上的表面形貌 随沉积时间的演化. 通过对薄膜生长形貌的动力学标度表征，研究了射频反应磁控溅射条件 下，ZnO薄膜的成核过程及生长动力学行为. 研究发现，ZnO在基片表面的成核过程可分为初 期成核阶段、低速率成核阶段和二次成核阶段. 对于Si(100)基片，三个成核阶段的生长指 数分别为β₁=1.04，β₂=0.25±0.01，β₃=0.74；对 于Si(11 关键词： ZnO薄膜 磁控溅射 生长动力学 成核机制     

不同参数溅射的ZnO薄膜硫化后的特性

采用直流反应磁控溅射法在玻璃和石英衬底上沉积了ZnO薄膜, 然后将它们在H^２S气流中 硫化得到ZnS薄膜．用x射线粉末衍射仪(XRD)、扫描电子显微镜(SEM)和UV-VIS透过光谱对Zn S薄膜样品进行了分析．结果表明, 该ZnS薄膜为六角晶体结构, 沿(002)晶面择优取向生长, 其结晶状态和透过光谱与工作气压、Ar/O^２流量比密切相关. 当气压高于1Pa 时, 得 到厚度很小的ZnS薄膜; 而气压低于1Pa时, 沉积的ZnO薄膜则不能全部反应生成ZnS. 另外, 当Ar/O^２流量比低于4∶1或高于4∶1时, 结晶状态都会变差. 此外, 由于ZnS薄 膜具有高 的沿(002)晶面择优取向的生长特性, 使得退火或未退火ZnO薄膜硫化后的晶粒尺寸变化很小 . 关键词： ZnS薄膜 磁控溅射 ZnO硫化 太阳电池     

Si(001)基片上反应射频磁控溅射ZnO薄膜的两步生长方法

利用反应射频磁控溅射技术，采用两步生长方法制备了ZnO薄膜，探讨了基片刻蚀时间和低温过渡层沉积时间对ZnO薄膜生长行为的影响.研究结果表明，低温ZnO过渡层的沉积时间所导致的薄膜表面形貌的变化与过渡层在Si(001)表面的覆盖度有关.当低温过渡层尚未完全覆盖基片表面时，ZnO薄膜的表面岛尺度较小、表面粗糙度较大，薄膜应力较大；当低温过渡层完全覆盖Si(001)基片后，ZnO薄膜的表面岛尺度较大、表面粗糙度较小，薄膜应力较小.基片刻蚀时间对薄膜表面形貌的影响与低温过渡层的成核密度有关.随着刻蚀时间的增加，ZnO薄膜的表面粗糙度逐渐下降，表面形貌自仿射结构的关联长度逐渐减小. 关键词： ZnO薄膜 反应射频磁控溅射 两步生长 形貌分析     

O2流量对磁控溅射N掺杂TiO2薄膜成分及晶体结构的影响

利用直流脉冲磁控溅射方法在室温下通过改变O₂流量制备具有不同晶体结构的N掺杂TiO₂薄膜,利用台阶仪、X射线光电子能谱仪、X射线衍射仪、紫外-可见分光光度计等设备对薄膜沉积速率、化学成分、晶体结构、禁带宽度等进行分析.结果表明:所制备的薄膜元素配比约为TiO_1.68±0.06N_0.11±0.01,N为替位掺杂,所有样品退火前后均未形成Ti—N相结构,N掺杂TiO₂薄膜的沉积速率、晶体结构等主要依赖于O₂流量.在O₂流量为2 sccm时,N掺杂TiO₂薄膜沉积速率相对较高,薄膜为非晶态结构,但薄膜内含有锐钛矿(anatase)和金红石(rutile)相晶核,退火后薄膜呈anatase和rutile相混合结构,禁带宽度仅为2.86 eV.随着O₂流量的增加,薄膜沉积速率单调下降,退火后样品禁带宽度逐渐增加.当O₂流量为12 sccm时,薄膜为anatase相择优生长,退火后呈anatase相结构,禁带宽度为3.2 eV.综合本实验的分析结果,要在室温条件下制备晶态N掺杂TiO₂薄膜,需在高O₂流量(＞10 sccn)条件下制备. 关键词： 2薄膜')" href="#">N掺杂TiO₂薄膜 磁控溅射 化学配比 晶体结构     

大气压等离子体辅助多晶硅薄膜化学气相沉积参数诊断

本文采用发射光谱法诊断了大气压下Ar气、SiCl₄及H₂气混合气体（Ar/SiCl₄/H₂）射频放电等离子体射流特性.利用Si原子谱线强度计算了电子激发温度并以此估算了Si原子数密度,研究了射频功率及气体流量对电子激发温度和Si原子数密度以及SiCl₄解离率的作用. 关键词： 大气压等离子体射流 发射光谱 电子激发温度 多晶硅薄膜沉积     

多晶薄膜表面粗化与生长方式转变

采用原子力显微镜研究了磁控溅射多晶薄膜表面粗化行为对归一化沉积温度T_s/T_m(T_s是沉积温度，T_m是材料熔点)的依赖性与薄膜生长方式转变行为.随着T_s/T_m增加，薄膜表面粗糙度增加，而表征粗糙度随时间演化特征的生长指数β历经了先减小再增加的过程.β对T_s/T_m的依赖关系反映了薄膜生长方式的转变行为，即薄膜生长依次由随机生长方式向表面扩散驱动生长方式与异常标度行为生长方式转变.在低于体扩散控制薄膜生长的温度时，晶界扩散机理导致多晶薄膜的表面粗化的异常标度行为. 关键词： 多晶薄膜 表面粗化 温度 生长     

生长温度对磁控溅射ZnO薄膜的结晶特性和光学性能的影响

采用反应射频磁控溅射方法，在Si (100) 基片上制备了具有高c轴择优取向的ZnO薄膜.利用 原子力显微镜、透射电子显微镜、X射线衍射分析、拉曼光谱等表征技术，研究了沉积温度 对ZnO薄膜的表面形貌、晶粒尺度、应力状态等结晶性能的影响；通过沉积温度对透射光谱 和光致荧光光谱的影响，探讨了ZnO薄膜的结晶特性与光学性能之间的关系.研究结果显示， 在室温至500℃的范围内，ZnO薄膜的晶粒尺寸随沉积温度的增加而增加，在沉积温度为500 ℃时达到最大；当沉积温度为750℃时，ZnO薄膜的晶粒尺度有所减小；在室温至750℃的范 围内，薄膜中ZnO晶粒与Si基体之间均存在着相对固定的外延关系；在沉积温度低于500℃时 ，制备的ZnO薄膜处于压应变状态，而750℃时沉积的薄膜表现为张应变状态.沉积温度的不 同导致ZnO薄膜的折射率、消光系数、光学禁带宽度以及光致荧光特性的变化，沉积温度对 紫外光致荧光特性起着决定性的作用.此外，探讨了影响薄膜近紫外光致荧光发射的可能因 素. 关键词： ZnO薄膜 表面形貌 微观结构 光学常数     

Structural characterization of β-V2O5 films prepared by DC reactive magnetron sputtering

β-V₂O₅ films were successfully prepared on silicon substrates by direct current (DC) reactive magnetron sputtering. X-ray diffraction (XRD), Raman spectra and field emission scan electron spectroscopy (SEM) were used to characterize the samples. Results revealed that the deposition temperature significantly influenced on the crystal structure of V₂O₅ films in the growth process. When the deposition temperature was below 500 °C, the sputtered film exhibited the α-V₂O₅ structure. However, β-V₂O₅ film was successfully obtained at 550 °C. High deposition temperature might provide V and O ions high mobility and energy in the reactive sputtering process, which induced the metastable β-V₂O₅ phase formed. The thermal stability of β-V₂O₅ film was studied by micro-Raman spectroscopy. The structure of sputtered β-V₂O₅ film was unstable under high temperature conditions (beyond 500 °C).     

Thermal stability of ZnO thin film prepared by RF-magnetron sputtering evaluated by thermal desorption spectroscopy

Thermal stability of sputter deposited ZnO thin films was evaluated by thermal desorption spectroscopy (TDS). Desorption of Zn was mainly observed from the films deposited at low O₂/Ar gas ratio and low RF power. In contrast, O₂ desorption was mainly observed from the films deposited at high O₂/Ar gas ratio and high RF power. The amount of desorbed O₂ from the film increased with increasing the O₂/Ar gas flow ratio and the RF power. Furthermore, the desorption temperature of O₂ increased with increasing the RF power during the deposition. Thermal stability of the ZnO films was controlled not only by the O₂/Ar gas flow ratio, but also applied RF power to the target.     

高择优取向铌酸锶钡薄膜的射频磁控溅射制备

采用溶胶-凝胶法在(100)Si单晶上预先制备出掺钾(K)的铌酸锶钡(SBN)缓冲层,利用射频磁控溅射法在缓冲层KSBN上沉积出高择优取向的铌酸锶钡薄膜,获得了磁控溅射法制备择优取向铌酸锶钡薄膜的相关工艺参数,研究发现,KSBN缓冲层能够很有效地克服衬底与SBN薄膜之间较大的晶格失配,在氧气氩气的比例为1∶2,工作气压为10 Pa,溅射功率300 W,衬底温度300℃,退火温度为800℃的工艺条件下,能够获得c轴高度择优取向的铌酸锶钡铁电薄膜.利用X射线衍射仪,原子力显微镜等仪器分析了薄膜 关键词： 磁控溅射 高择优取向 p-n结效应     

Study of structural, optical and electrical properties of ZnO and SnO2 thin films

The investigation of structure, optical and electrical properties of tin and zinc oxide films on glass substrates by using magnetron sputtering are carried out. X-ray data show the formation of textured tin oxides film during deposition and its transformation to SnO₂ polycrystalline film at low temperature (200 C) if the concentration of oxygen in the chamber is high (O₂ — 100%, Ar — 0%). Optimal conditions of SnO₂ polycrystalline film deposition (pressure of Ar–O₂ mixture in chamber — 2.7 Pa, concentration of O₂ — 10%) are determined. Low resistivity of as-deposited ZnO film and increasing ZnO crystallite sizes and phase volume at temperatures higher than the melting point of Zn (419.5 C) are explained by formation of conductive Zn and ZnO particle chains and their destruction, respectively.     

Effects of crystalline quality on the ultraviolet emission and electrical properties of the ZnO films deposited by magnetron sputtering

The ZnO films were deposited on c-plane sapphire, Si (0 0 1) and MgAl₂O₄ (1 1 1) substrates in pure Ar ambient at different substrate temperatures ranging from 400 to 750 °C by radio frequency magnetron sputtering. X-ray diffraction, photoluminescence and Hall measurements were used to evaluate the growth temperature and the substrate effects on the properties of ZnO films. The results show that the crystalline quality of the ZnO films improves with increasing the temperature up to 600 °C, the crystallinity of the films is degraded as the growth temperature increasing further, and the ZnO film with the best crystalline quality is obtained on sapphire at 600 °C. The intensity of the photoluminescence and the electrical properties strongly depend on the crystalline quality of the ZnO films. The ZnO films with the better crystallinity have the stronger ultraviolet emission, the higher mobility and the lower residual carrier concentration. The effects of crystallinity on light emission and electrical properties, and the possible origin of the n-type conductivity of the undoped ZnO films are also discussed.     

Control of diameter of ZnO nanorods grown by chemical vapor deposition with laser ablation of ZnO

We made a study of controlling diameters of well-aligned ZnO nanorods grown by low-pressure thermal chemical vapor deposition combined with laser ablation of a sintered ZnO target, which was developed by us. Until now, it has been impossible to control diameters of ZnO nanorods, while the growth orientation was maintained well-aligned. In this study we developed a multi-step growth method to fabricate well-aligned nanorods whose diameters could be controlled. Metal Zn vapor and O₂ are used as precursors to grow ZnO nanorods. N₂ is used as a carrier gas for the precursors. A substrate is an n-Si (111) wafer. A sintered ZnO target is placed near the substrate and ablated by a Nd–YAG pulsed laser during ZnO nanorod growth. The growth temperature is 530 C and the pressure is 66.5 Pa. A vertical growth orientation of ZnO nanorods to the substrate is realized in the first-step growth although the diameter cannot be controlled in this step. When an O₂ flow rate is 1.5 sccm, well-aligned nanorods with 100 nm diameter are grown. Next, the second-step nanorods are grown on only the flat tip of the first-step nanorods. The diameters of the second-step nanorods can be controlled by adjusting the O₂ flow rate, and the growth direction is kept the same as that of the first-step nanorods. When the O₂ flow rate in second-step growth is smaller than 0.6 sccm, the diameter of the second-step nanorods is 30–50 nm. When the O₂ flow rate is between 0.75 and 3.0 sccm, the diameter is almost same as that of the first-step nanorods. When the O₂ flow rate is larger than 4.5 sccm, the diameter is increased with increasing O₂ flow rate. Further, the third-step ZnO nanorods with gradually increased diameters can be grown on the second-step nanorods with 1.5 sccm O₂ flow rate and without laser ablation.     

脉冲磁控溅射法制备单斜相氧化铒涂层

用中频脉冲反应磁控溅射法,在溅射功率为78 W,93 W和124 W以及衬底温度分别为室温,500 ℃及677 ℃下制备了氧化铒涂层.采用原子力显微镜、纳米压痕、X射线衍射和掠入射X射线衍射法研究了涂层的形貌、力学性能及物相结构.测量了涂层的电学性能.结果显示,脉冲磁控溅射沉积氧化铒涂层具有较高的沉积速率.实验制备得到了单斜相结构的氧化铒涂层.提高溅射功率时,沉积速率从28 nm/min增大至68 nm/min,涂层的结晶质量显著下降.提高衬底温度至500 ℃和677 ℃时,单斜相衍射峰强度下降.分析认为 关键词： 氧化铒 脉冲磁控溅射 单斜晶相     

高浓度Er/Yb共掺ZnO薄膜的结构及室温光致发光特性

采用射频磁控溅射方法制备了Er/Yb共掺ZnO薄膜,研究了退火处理对高浓度Er/Yb共掺ZnO薄膜的结构演化和光致发光(PL)特性的影响。X射线衍射分析结果表明:Er/Yb掺杂导致ZnO薄膜的晶粒细化及择优取向性消失,ZnO晶粒随退火温度的增加而逐渐长大。900℃退火时,出现Er3 、Yb3 偏析,退火温度高于1000℃时,薄膜与基体间发生了界面反应,1200℃时,ZnO完全转变为Zn2SiO4相。光致发光测量结果表明:高于900℃退火处理后,Er/Yb共掺ZnO薄膜在1540 nm附近具有明显的光致发光,发光强度在退火温度为1050℃时达到最大值;光致发光光谱呈现典型的晶体基质中Er3 离子发光光谱所具有的明锐多峰结构特征。此外,探讨了薄膜结构演化及其对光致发光光谱的影响。