CuCl2/γ-Al2O3催化剂的EPR研究

通过测定Cu含量不同的新鲜CuCl₂/γ-Al₂O₃催化剂的EPR谱,以及对EPR谱的线型及强度的计算机处理和理论拟合等,研究了催化剂中CuCl₂在载体表面的分散方式,和Cu含量对Cu²⁺配位形式的影响.EPR结果表明,催化剂表面的Cu²⁺至少有两种不同配位状态.新鲜催化剂中所存在的两种不同谱线的比例决定了EPR谱的线型和强度,而两种谱线的比例又取决于催化剂中的Cu含量.在低Cu催化剂中Cu²⁺相互离散,倾向于形成富氧配位,具有较高的EPR强度,只有在Cu含量较高时,Cu²⁺才能形成富氯配位.鉴于低Cu催化剂不能与乙烯反应,而高Cu催化剂则可以使乙烯转化为二氯乙烷的事实,认为富氧配位的Cu²⁺可能具有与乙烯反应的活性.     

载体钒氧化物中钒—吸附物分子相互作用的ESR研究

电子自旋共振技术已经用来研究还原态V_2O_5/SiO_2催化剂和各种吸附分子的相互作用。实验指出:具有四面体配位结构的V~(4+)离子是活性中心,V~(4+)和CH_2OH,HCl,CH_3CN分子的相互作用导致形成八面体配位结构的表面VO~(2+)络合物,它们的ESR和成键参数计算指出不成对电子主要定位在钒离子的d轨道上。77 K下吸附O_2分子已经观察到氧自由基的ESR信号,但吸附乙烯和丙烯不能改变V~(4+)离子的配位结构。     

乙丙共聚物的13C NMR研究

研究用化学反应法制备的镁钛系载体高效催化剂合成的乙丙共聚物的¹³C NMR谱图,提出了无需进行分峰处理,通过将谱图直接分为八个独立的区域,并选取其中受仪器测试条件等影响较小的五个谱区的强度,直接计算此类共聚物序列分布的方法,并分别采用伯努利模型和马尔科夫模型对共聚物的三单元组序列分布进行处理,指出在化学反应法制备的载体催化剂催化的乙丙共聚合扫次末端基效应机理进行,且催化剂活性中心有利于乙丙各自的均聚合.     

Mo-SiO2-C3H6催化反应体系的ESR动态表征

文章考察了Mo-SiO₂催化剂体系在丙烯歧化反应过程中的动态ESR波谱,发现在催化歧化反应过程中有两种Mo⁵⁺顺磁中心,一种为扰动八面体配位,g_||=1.89,g_⊥=1.94;另一种为扰动四棱锥配位,g_||=1.86,g_⊥=1.95。测得同位素^95,97Mo⁵⁺的各向异性超精细耦合常数A_||=90.3×10^-4cm^-1,A_⊥=44.8×10^-4cm^-1;观测到反应产生的积炭信号,g≈2.0O₂;氧阴离子自由基信号g₁=2.018,g₂=2.011,g₃=2.005。用LCAO-MO理论对上述Mo⁵⁺的ESR波谱进行计算,求得分子轨道系数,发现并总结出△g_||/△g_⊥与△g成直线关系,并建议用△g_||/△g_⊥=4(△E(B₂→E))/(△E(B₂→B₁)(β₁/ε)²之比值作为衡量C_4v扰动程度的尺度。     

丙烯聚合负载型Ziegler-Natta催化剂的ESR研究

用ESR方法对MgCl₂负载的钛系Ziegier-Natta催化剂进行了研究,获得了分辩率较好的谱图,并结合前人的工作将信号的归属同钛原子在MgCl₂上的负载情况对应起来.同时考察了内外给电子化合物对ESR谱图的影响,探讨了它们可能的作用机理.     

ESR研究非晶Ag+导体的晶化

用电子自旋共振(ESR)方法对非晶Ag⁺离子导体0.85AgI~0.15Ag₄P₂O₇的热处理晶化过程进行研究,在样品中掺入微量(约1×10^-3 g/g)的Mn²⁺或V⁴⁺离子作为自旋探针离子,它们的ESR谱强度随升温线性减弱,当样品完全晶化时ESR谱消失。这样测定的样品完全晶化的温度分别为98℃(掺Mn的)和108℃(掺V的).本文还对Mn²⁺和V⁴⁺的ESR谱进行了分析。     

磷酸盐、氟磷酸盐和氟化物玻璃中过渡金属离子的顺磁共振研究(Ⅰ)——Cr3+,Mo3+

本文研究了磷酸盐、氟磷酸盐和氟化物玻璃中Cr³⁺的顺磁共振(以下简称ESR),从自旋哈密顿出发计算了Cr³⁺的有效g因子,指出低场谱线主要起源于两个Kramers双重态之间的跃迁,确定了自旋哈密顿参数:D=0.15—0.4cm^-1,E/D=0.15—0.3,零场分裂为0.3—0.8cm^-1,本文还报道了磷酸盐玻璃中Mo³⁺的ESR。 关键词：     

掺杂LiF的ESR谱和ENDOR谱研究

LiF:Mg,Cu热释光(TL)磷光体在γ辐照后产生F⁰顺磁中心,其g因子为g_xx=2.0030,g_yy=2.0450,g_zz=2.0251,裂分为A_xx=511.04G,A_yy=505.42G,A_zz=507.26G。F⁰中心的浓度随Mg⁺⁺浓度的增加而下降。磷光体的ENDOR谱显示F⁰中心附近有铜核存在。照射前和照射后24h测量均未发现Cu⁺⁺的ESR谱,表明铜是以Cu⁺形式掺入的,照射并未引起Cu⁺离子化合价的改变。LiF:Mg,Cu,P在γ辐照前具有轴对称的Cu⁺⁺离子的ESR谱,辐照后产生了O^-空穴中心和PO₃^2-自由基,改变了Cu⁺⁺的环境,使Cu⁺⁺的谱发     

Al2O3-SiO2石油裂化催化剂上自由基空间分布的ESR成象

报道了用自己设计制作的电子自旋成象装置,对芳烃芳胺化合物在Al₂O₃-SiO₂催化剂表面酸中心所形成的正离子自由基进行二维ESR成象研究.     

以VO2+为自旋探针的配位共聚催化剂分子筛载体的ESR研究

以VO²⁺为自旋探针,观察了VO²⁺负载的分子筛载体的微环境,在计算机上模拟了复杂的多中心的实验ESR谱,发现VO²⁺在载体上的分散状况不仅取决于制备条件,也和分子筛的种类有关。利用这种方法,可得探针在载体上所处微环境的信息,进而可用于指导配位聚合催化剂载体的选择。     

Theoretical investigation of ethylene/1-butene copolymerization process using constrained geometry catalyst (CpSiH2NH)-Ti-Cl2

The ethylene/1-butene copolymerization using constrained geometry catalyst CpSiH₂-NH-TiCl₂ (CGC) was investigated by the density functional theory and molecular dynamics. Structures and energetics of reactants, π-complexes, transition states, and products during insertion of ethylene and 1-butene monomers into the catalytic reactive site of the CGC were investigated by the density functional theory (DFT) using the software Dmol³, while dynamics of atoms during copolymerization process was investigated by classical molecular dynamics (MD) using the New-Ryudo-CR program. The calculated results were compared with the available experimental and theoretical ones. It was found that the ethylene insertion into Ti-Me active species is energetically more favorable than the butene one and the 2,1-butene insertion is more favorable than 1,2-butene one. Once the initial ethylene insertion has taken place, the further ethylene insertion occurring with a less energy barrier, in good agreement with experimental findings.     

Ti：Al2O3晶体的电子自旋共振谱研究

Ｔｉ：Ａｌ２Ｏ３晶体中的顺磁中心Ｔｉ＾３＋由于强烈的晶格自旋耦合而使其电子自旋共振吸收只有在液拟温度附近才能看到，本实验在液氮温度附近记录到由许多强的的吸收峰迭加于Ｔｉ＾３＋宽吸收线所组成的电子自旋共振谱，这些吸吸收峰被认为是Ａｌ２Ｏ３基质中的Ｆｅ＾３＋，Ｍｎ＾２＋，Ｃｒ＾３＋，Ｍｏ＾３＋，Ｆｅ＾２＋，Ｃｏ＾２＋等杂质的共振吸收及Ｔｉ＾２＋３Ａ２ｇ基态的双量子跃迁造成的。     

Experimental and theoretical studies of reaction pathways of direct propylene epoxidation on model catalyst surfaces

The direct epoxidation of propylene to propylene oxide (PO) using molecular oxygen is an attractive alternative to current production methods using chlorohydrin or hydroperoxide-mediated processes, which are environmentally harmful and expensive. Although direct ethylene epoxidation using Ag-based catalysts has been practiced industrially for decades, due to the presence of allylic hydrogen in propylene the selectivity toward epoxide is generally much lower for propylene than for ethylene. Mechanistic understanding on well-characterized surfaces of model catalysts can potentially provide guidance to effectively alter the electronic properties of the catalyst in order to increase PO selectivity. This review summarizes both experimental and theoretical studies on model catalysts for propylene epoxidation and their contributions to elucidating the reaction mechanism, intermediates, and active sites. We first show examples of experimental studies on Cu, Ag, and Au surfaces, and compare the reaction pathways and intermediates on these surfaces. Novel approaches including plasmon-mediated catalysis and utilization of shape-controlled crystal facets that open new opportunities for improving PO selectivity will also be discussed. We then describe how density functional theory (DFT) calculations have provided important insights into the reaction mechanism and active sites on Cu, Ag, and Au surfaces and clusters. Propylene oxidation pathways on other relevant metal surfaces will also be discussed. The combined experimental and computational studies elucidate the nature of surface oxygen species and the role of the oxametallacycle intermediate. We conclude by highlighting design principles and insights for guiding further development of active and selective propylene epoxidation catalysts.     

Ni3V2O8催化性能与X射线光电子能谱分析

文章采用微波加热,草酸盐共沉淀法制备了Ni3V2O8催化剂,并对催化剂进行了BET,XRD,H2-TPR,XPS,TEM和电导等技术表征,分析研究了Ni3V2O8催化剂的丙烷氧化脱氢(ODH)制丙烯催化性能与其表面物种的关系.XRD,TEM和电导实验结果表明本方法制得的Ni3V2O8催化剂晶粒均匀,平均粒径为30 nm,具有p-型半导体性质.TPR和XPS实验结果显示Ni3V2O8催化剂中,晶格氧可以较容易转换成未完全还原氧,使催化剂内各种价态的钒之间易于进行氧化还原反应并形成氧缺位,从而催化剂的表面含有较多未充分还原氧物种O-和V4 物种.催化活性结果显示当丙烷的转化率为18.60%,丙烯选择性达到60.02%,在相同转化率条件下,比文献报道的NiO和Ni3V2O8共存催化体系中的丙烯选择性高,说明Ni3V2O8催化剂中存在未充分还原的O-和V4 物种有利于提高丙烯的选择性.     

Photoinduced oxygen-vacancy related centers in PbWO 4 : Electron spin resonance and thermally stimulated luminescence study

Using electron spin resonance (ESR) and thermally stimulated luminescence (TSL) three different electron traps based on regular W sites perturbed by oxygen vacancies have been identified in PbWO 4 . Analysis of ESR spectra parameters ( g -factor values and principal axes orientations) has shown that revealed centers are (WO 3 ) m vacancy containing complex anions associated with a defect in Pb sublattice: (WO 3 ) m m A Pb complexes. One of the centers (W 1 ) is thermally stable up to 350-370 v K, while the other two (W 2 and W 3 ) only to 270-290 v K. Above these temperatures trapped electrons become free and recombine with localized holes, giving rise to TSL glow peaks at T\approx 323\,\hbox{K} and 365\,\hbox{K} . Using the initial rise method the 323\,\hbox{K} TSL peak-shape was fitted allowing the first order recombination kinetic that gives trap parameters E = 0.88\,\hbox{eV} and s\simeq 5\ast 10^{12}1/\hbox{s} .     

Further EPR study of paramagnetic Cr3+ centers in KTiOPO4

Careful reanalysis of EPR spectra of Cr³⁺ ions in KTiOPO₄ has been carried out in order to resolve the weaker lines not considered in our previous study. Two additional centers denoted as C and D have now been identified and the respective spin Hamiltonian parameters have been determined. The reanalysis of the results for the centers A and B identified previously and those for the new centers C and D indicates that the centers A and C originate from Cr³⁺ ions at Ti(2) sites, whereas the centers B and D originate from Cr³⁺ ions at Ti(1) sites. Sixteen magnetically inequivalent Cr³⁺ sites are assigned to two crystallographically different titanium sites: Ti(1) and Ti(2). Possible charge compensation models for the two different centers arising from Cr³⁺ ions at each of the two Ti sites are also suggested.