Investigation of protein adsorption and electrochemical behavior at a gold electrode

The adsorption of two model proteins, human serum albumin and immunoglobulin G, on a gold electrode surface was investigated using 125I radiolabeling and cyclic voltammetry (CV). 125I radiolabeling was used to determine the extent of protein adsorption, while CV was used to ascertain the effect of the adsorbed protein layer on the electron transfer between the gold electrode and an electroactive moiety in solution, namely, K3Fe(CN)6. The adsorbed amounts of HSA and IgG agreed well with previous results and showed approximately monolayer coverage. The amount of adsorbed protein increased when a positive potential (700 mV) was applied to the electrode, while the application of a negative potential (-800 mV) resulted in a decrease. When the solution pH was varied to alter the charge on the protein, the adsorption trends appeared to follow electrostatic interaction, namely, greater adsorption when the electrode and the protein possessed opposite charge and vice versa. The adsorbed protein layer had the effect of blocking the electron transfer. It was possible to correlate the degree of electron blocking with the amount of adsorbed protein to show that the greater the adsorption, the larger the blocking effect. Of the two proteins used, HSA proved to be more efficient at blocking the electron transfer.     

Electrochemical investigation of carbon nanotube nanoweb architecture in biological media

The as-synthesised carbon nanotube nanoweb modified carbon fibre paper (CNT-NW/CFP) was investigated to study the effect of surface protein adsorption in electrochemical activities using immunoglobulin G (IgG) and human serum albumin (HSA). Detail chemical characterisation was carried out using 125I radiolabeling, cyclic voltammetry and electrochemical impedance spectroscopy. Both HSA and IgG were adsorbed onto the electrode at levels of approximately 120 mg/m². Cyclic voltammetry indicated that the surface-adsorbed protein had a detrimental effect on oxidation/reduction of ferri/ferricyanide whilst EIS spectra revealed a slight increase in impedance and decrease in capacitance.     

Dynamics of fibronectin adsorption on TiO2 surfaces

In the present work we analyze the dynamics of fibronectin (FN) adsorption on two different stable titanium oxides, with varied surface roughness, and chemically similar to those used in clinical practice. The two types of titanium oxide surfaces used were TiO2 sputtered on Si (TiO2 sp) and TiO2 formed on commercially pure titanium after immersion in H2O2 (TiO2 cp). Surface characterization was previously carried out using different techniques (Sousa, S. R.; Moradas-Ferreira, P.; Melo, L. V.; Saramago, B.; Barbosa, M. A. Langmuir 2004, 20 (22), 9745-9754). Imaging and roughness analysis before and after FN adsorption used atomic force microscopy (AFM) in tapping mode, in air, and in magnetic alternating current mode, in liquid (water). FN adsorption as a function of time was followed by X-ray photoelectron spectroscopy (XPS), by radiolabeling of FN with 125I (125I-FN), and by ellipsometry. Exchangeability studies were performed using FN and HSA. AFM roughness analysis revealed that, before FN adsorption, both TiO2 surfaces exhibited a lower root-mean-square (Rq) and maximum peak with the depth of the maximum valley (Rmax) roughness in air than in water, due to TiO2 hydration. After protein adsorption, the same behavior was observed for the TiO2 sp substrate, while Rq and Rmax roughness values in air and in water were similar in the case of the TiO2 cp substrate, for the higher FN concentration used. Surface roughness was always significantly higher on the TiO2 cp surfaces. AFM led to direct visualization of adsorbed FN on both surfaces tested, indicating that after 10 min of FN incubation the TiO2 sp surface was partially covered by FN. The adsorbed protein seems to form globular aggregates or ellipsoids, and FN aggregates coalesce, forming clusters as the time of adsorption and the concentration increase. Radiolabeling of FN revealed that a rapid adsorption occurs on both surfaces and the amount adsorbed increased with time, reaching a maximum after 60 min of incubation. Time dependence is also observed for the evolution of the atomic (%) of N determined by XPS and by the increase of the thickness by ellipsometry. TiO2 cp adsorbs more FN than the TiO2 sp surfaces, after 60 min of adsorption, as shown by the radiolabeling data. FN molecules are also more strongly attached to the former surface as indicated by the exchangeability studies. The overall results provide novel evidence that FN spontaneously adsorbs as a self-assembly at TiO2 surfaces as a function of time. The aggregate structure is an intermediate feature shared by some protein fibrillar assemblies at interfaces, which is believed to promote cell adhesion and cytoskeleton organization (Pellenc, D.; Berry, H.; Gallet, O. J. Colloid Interface Sci. 2006, 298 (1), 132-144. Maheshwari, G.; Brown, G.; Lauffenburger, D. A.; Wells, A.; Griffith, L. G. J. Cell Sci. 2000, 113 (10), 1677-1686).     

Human serum albumin adsorption on TiO2 from single protein solutions and from plasma

In the present work, the adsorption of human serum albumin (HSA) on commercially pure titanium with a titanium oxide layer formed in a H(2)O(2) solution (TiO(2) cp) and on TiO(2) sputtered on Si (TiO(2) sp) was analyzed. Adsorption isotherms, kinetic studies, and work of adhesion determinations were carried out. HSA exchangeability was also evaluated. Surface characterization was performed by atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and wettability studies. The two TiO(2) surfaces have very distinct roughnesses, the TiO(2) sp having a mean R(a) value 14 times smaller than the one of TiO(2) cp. XPS analysis revealed consistent peaks representative of TiO(2) on sputtered samples as well as on Ti cp substrate after 48 h of H(2)O(2) immersion. Nitrogen was observed as soon as protein was present, while sulfur, present in disulfide bonds in HSA, was observed for concentrations of protein higher than 0.30 mg/mL. The work of adhesion was determined from contact angle measurements. As expected from the surface free energy values, the work of adhesion of HSA solution is higher for the TiO(2) cp substrate, the more hydrophilic one, and lower for the TiO(2) sp substrate, the more hydrophobic one. The work of adhesion between plasma and the substrates assumed even higher values for the TiO(2) cp surface, indicating a greater interaction between the surface and the complex protein solutions. Adsorption studies by radiolabeling of albumin ((125)I-HSA) suggest that rapid HSA adsorption takes place on both surfaces, reaching a maximum value after approximately 60 min of incubation. For the higher HSA concentrations in solution, a multilayer coverage was observed on both substrates. After the adsorption step from single HSA solutions, the exchangeability of adsorbed HSA molecules by HSA in solution was evaluated. The HSA molecules adsorbed on TiO(2) sp seem to be more easily exchanged by HSA itself than those adsorbed on TiO(2) cp after 24 h. In contrast, after 72 h, nearly all the adsorbed albumin molecules effectively exchange with other albumin molecules.     

Highly conductive nanostructured C-TiO2 electrodes with enhanced electrochemical stability and double layer charge storage capacitance

The present work reports the structural and electrochemical properties of carbon-modified nanostructured TiO(2) electrodes (C-TiO(2)) prepared by anodizing titanium in a fluoride-based electrolyte followed by thermal annealing in an atmosphere of methane and hydrogen in the presence of Fe precursors. The C-TiO(2) nanostructured electrodes are highly conductive and contain more than 1 × 10(10) /cm(2) of nanowires or nanotubes to enhance their double layer charge capacitance and electrochemical stability. Electrogenerated chemiluminescence (ECL) study shows that a C-TiO(2) electrode can replace noble metal electrodes for ultrasensitive ECL detection. Dynamic potential control experiments of redox reactions show that the C-TiO(2) electrode has a broad potential window for a redox reaction. Double layer charging capacitance of the C-TiO(2) electrode is found to be 3 orders of magnitude higher than an ideal planar electrode because of its high surface area and efficient charge collection capability from the nanowire structured surface. The effect of anodization voltage, surface treatment with Fe precursors for carbon modification, the barrier layer between the Ti substrate, and anodized layer on the double layer charging capacitance is studied. Ferrocene carboxylic acid binds covalently to the anodized Ti surface forming a self-assembled monolayer, serving as an ideal precursor layer to yield C-TiO(2) electrodes with better double layer charging performance than the other precursors.     

ATR-IR spectroscopic studies of the influence of phosphate buffer on adsorption of immunoglobulin G to TiO2

In situ attenuated total reflectance infrared (ATR-IR) spectroscopy has been applied to the study of the influence of phosphate on the extent of protein adsorption onto TiO₂. Immunoglobulin G (Ig.G) was adsorbed onto a TiO₂ sol–gel film from solutions containing phosphate or NaCl. Monitoring of the amide II absorbance (v=1545 cm⁻¹) confirmed reduced protein adsorption from the phosphate containing solution. In situ ATR-IR spectroscopy was also used to study phosphate induced desorption of Ig.G. Solutions containing various phosphate concentrations were passed over a TiO₂ film with Ig.G adsorbed to it. As the concentration of phosphate increased the amide II absorbance decreased confirming the removal of bound Ig.G from the TiO₂ surface. As the amide II absorbance decreased the phosphate absorbance (v=1080 cm⁻¹) increased suggesting accumulation of phosphate at the TiO₂ surface. Not all of the bound protein could be displaced from the TiO₂ surface by phosphate suggesting the presence of weakly and strongly bound Ig.G.     

Modeling of co-adsorption of cations and anions localized in different layers of the dense part of electrical double layer under the conditions of linear charge dependence of the adsorption energy

Effects of interference of the adsorption of cations and anions located in different layers of the electrical double layer dense part (under the conditions of linear dependence of their adsorption energy on the electrode charge) analyzed in the context of a system comprising two Frumkin mixed isotherms. The model was shown to suit for the explaining of the retraction of weakly adsorbed cations into the dense layer in the case of practical independence of the total surface excess of the cations on their localizing plane in the electrical double layer. The effect of co-adsorption of cations and anions in such systems on the total differential capacitance of electrode is analyzed.     

贮氢电极电化学阻抗谱及其数学模型

从分析贮氢电极的放电过程着手，建立了具有明显物理意义贮氢电极电化学阻抗谱的数学模型，以该数学模型为基础，讨论了与电极材料性质和电极荷电状态相联系的一些参数。     

溶菌酶在裸金电极和疏基乙酸或正十二疏烷基醇修饰电极上的吸附

电化学石英晶体阻抗系统;疏基乙酸;溶菌酶在裸金电极和疏基乙酸或正十二疏烷基醇修饰电极上的吸附     

Electrical probing of endothelial cell behaviour on a fibronectin/polystyrene/thiol/gold electrode by Faradaic electrochemical impedance spectroscopy (EIS)

The electrochemical impedance spectroscopy (EIS) technique has been shown to be an effective tool for monitoring endothelial cell behaviour on a multilayer functionalised gold electrode. Polystyrene, a reproducible model substrate, is deposited as a thin layer on a thiol functionalised gold electrode. Fibronectin, a protein promoting endothelial cell adhesion, is then adsorbed on the polystyrene surface. The different steps of this multilayer assembly are characterized by Faradaic impedance. The charge transfer resistance and the capacitance for the total layer are modified at each step according to the electrical properties of each layer. This gives the endothelial cells' electrical state in terms of its resistive and capacitive properties. In this study, the endothelial cell layer presents a specific charge transfer resistance equal to 1.55 kOmega cm(2) with no large defects in the cell layer, and a specific capacitance equal to few microF cm(-2) explained by the existence of pseudopods. These electrical properties are correlated to the endothelial cell viability, adhesion and cytoskeleton organization.     

Chemical Adsorption onto an ITO Substrate of Single‐Wall Carbon Nanotube Functionalized by Carboxylic Groups as an Efficient Support for Electrocatalyst

A single‐wall carbon nanotube functionalized by carboxylic groups (SWNT‐CA) was found to be adsorbed on an indium tin oxide (ITO) electrode by chemical interaction between carboxylic groups and the ITO surface. The adsorption experiments indicated that the narrow pH conditions (around pH 3.0) exist for its adsorption which is restricted by preparation of stable fluid dispersion (favorable at higher pH) and by the chemical interaction (favorable at lower pH). Atomic force microscopic (AFM) measurements suggest that fragmented SWNT‐CA are adsorbed, primarily lying on the surface. Electrochemical impedance analysis indicated that an electrochemical double layer capacitance of the SWNT‐CA/ITO electrode is considerably higher than that for the ITO electrode, suggesting that the interfacial area between the electrode surface and the electrolyte solution is enlarged by the SWNT‐CA layer. Pt particles were deposited as a catalyst on the bare ITO and SWNT‐CA‐coated ITO (SWNT‐CA/ITO) electrodes to give respective Pt‐modified electrodes (denoted as a Pt/ITO electrode and a Pt/SWNT‐CA/ITO electrode, respectively). The cathodic current for the Pt/SWNT‐CA/ITO electrode was 1.7 times higher than that for the Pt/ITO electrode at 0.0 V, showing that the Pt/SWNT‐CA/ITO electrode works more efficiently for O₂ reduction at 0.0 V due to the SWNT‐CA layer. The enhancement by the SWNT‐CA layer is also effective for electrocatalytic proton reduction. It could be ascribable to the enlarged interfacial area between the electrode surface and the electrolyte solution.     

A novel dual-impedance-analysis EQCM system--investigation of bovine serum albumin adsorption on gold and platinum electrode surfaces

Both quartz crystal micro-balance (QCM) impedance and electrochemical impedance spectroscopy (EIS) methods are widely used in interface studies. This paper presents details about a new strategy for simultaneous, mutual-interference-free and accurate measurements of QCM impedance and EI, through connecting a suitable capacitance in series with the piezoelectric quartz crystal (PQC) between QCM impedance and EIS measurement instruments. Combined and individual measurements of QCM impedance and EIS during silver deposition gave results comparable with each other, demonstrating the reliability of the proposed method. Bovine serum albumin (BSA) adsorption on gold and platinum electrodes in Britton-Robinson (B-R) buffers was investigated, and the Fe(CN)6(3-)/Fe(CN)6(4-) couple was used as an electrochemical probe to characterize BSA adsorption. While the reversibility of Fe(CN)6(3-)/Fe(CN)6(4-) couple on bare Au and Pt electrodes changed very slightly with decreasing solution pH from pH approximately 7 to pH approximately 2, the standard rate constant (ks) of this couple increased abruptly with solution pH below pH approximately 4.5 at a BSA-modified Au electrode, but decreased with solution pH at a BSA-modified Pt electrode. By analyzing the QCM impedance data with a modified BVD equivalent circuit and the EI data with a modified Randle's equivalent circuit, inflexion changes at pH approximately 4.5 were all found at pH-dependent responses of the resonant frequency, the double-layer capacitance, the capacitance of the adsorbed BSA layer, the peak-absorbance values of BSA solutions at 277.5 and 224.5 nm, and so on. It was also found that a BSA adsorption layer can effectively inhibit gold corrosion during ferrocyanide oxidation in a ferrocyanide-containing BR solution. Some preliminary explanations of these findings have been given. The proposed method is highly recommended for wider applications in surface science.     

电解液离子与炭电极双电层电容的关系

以酚醛树脂基纳米孔玻态炭(NPGC)为电极, 通过微分电容伏安曲线的测试, 研究了水相体系电解液离子与多孔炭电极双电层电容的关系. 结果表明, 稀溶液中, 多孔炭电极的微分电容曲线在零电荷点(PZC)处呈现凹点, 电容降低, 双电层电容受扩散层的影响显著；若孔径小, 离子内扩散阻力大, 电容下降更为迅速, 扩散层对双电层电容的影响增大. 而增大炭材料的孔径或电解液浓度, 可明显减弱甚至消除扩散层对电容的影响. 炭电极的单位面积微分电容高, 仅表明孔表面利用率高, 如欲获得高的电容量, 还要有大的比表面积. 离子水化对炭电极的电容产生不利影响, 选用大离子和增大炭材料的孔径, 可有效降低离子水化对炭电极电容性能的影响.     

Simultaneous quartz crystal microbalance-electrochemical impedance spectroscopy study on the adsorption of anti-human immunoglobulin G and its immunoreaction at nanomaterial-modified Au electrode surfaces.

The quartz crystal microbalance method (QCM), in combination with electrochemical impedance spectroscopy (EIS), has been utilized to monitor in situ anti-human IgG adsorption on several Au-based surfaces, bare Au, nanogold/4-aminothiophenol (4AT)/Au, and multi-walled carbon nanotubes (MWCNT)/Au, and succeeding human IgG reactions. Also, the immobilization protocol of anti-human IgG via its glutaraldehyde (GA) cross-linking with self-assembled 4AT on an Au electrode and the subsequent surface immunoreaction were examined. The resonant frequency (f(0)) and the motional resistance (R(1)) of the piezoelectric quartz crystal (PQC) as well as electrochemical impedance parameters were measured and discussed. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) of the ferricyanide/ferrocyanide couple were examined before and after electrode modification, the antibody adsorption and antibody-antigen reactions. We found that the amount for antibody adsorption was the greatest on the colloid Au modified surface, and that at MWCNT ranked the second, while specific bioactivity was almost identical on the four kinds of surfaces. Two parameters simultaneously obtained at the colloid Au modified surface, Deltaf(0) and DeltaC(s) (interfacial capacitance), have been used to estimate the association constant of the immunoreaction.     

尖晶石锂锰氧化物电极首次脱锂过程的EIS研究

研究了尖晶石锂锰氧化物电极首次脱锂过程中的电化学阻抗特征. 通过选取适当的等效电路拟合实验所得的电化学阻抗谱数据, 获得了首次脱锂过程中固体电解质相界面膜(SEI膜)的电阻、电容以及电荷传递电阻、双电层电容等随电极极化电位的变化规律.     

In situ monitoring of gold-surface adsorption and acidic denaturation of human serum albumin by an isolation-capacitance-adopted electrochemical quartz crystal impedance system

Combined measurements of piezoelectric quartz crystal impedance (PQCI) and electrochemical impedance spectrum (EIS) using a suitable isolation capacitance is reported for the first time to monitor in situ adsorption and acidic denaturation of human serum albumin (HSA) on gold electrodes in Britton-Robinson (B-R) buffers. This method provides simultaneously mutual-interference-free and accurate parameters of EIS and PQCI. Effects of surface thiol-modification, electrode-potential and solution pH on HSA adsorption were examined and discussed. Comparative experiments of HSA adsorption in a B-R buffer of pH 6.42 on bare, cysteine- and 1-dodecanethiol-modified gold electrodes revealed that HSA adsorption is more significant on a hydrophobic (1-dodecanethiol-modified) surface. Insignificant electrode-potential effect implied minor electrostatic effects on HSA adsorption. The adsorption amount of HSA at pH 3.28 was found to be notably greater than those at pH 4.84 and 6.42. To characterize HSA adsorption, electrode standard rate constants (k_s) of the Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ couple were measured before and after HSA adsorption. The k_s-pH curves on an HSA-modified Au electrode revealed that k_s increased abruptly with the decrease of solution pH below pH ∼4. Moreover, pH-dependent responses of the resonant frequency, the motional resistance, the double-layer capacitance, the capacitance of adsorbed HSA layer and the peak absorbance of HSA solutions at 278 nm all exhibited an inflexion change at pH ∼4, and these findings have been explained on the basis of acidic denaturation of HSA and electrical charges carried by HSA molecules.     

Model description of specific adsorption of two anions on electrodes

Simultaneous specific adsorption of two anions on the electrode surface is considered. Calculations involve the use of the Frumkin adsorption isotherm for each anion and a model that describes the electric double layer structure based on one or two Helmholtz planes. Dependences of the ion adsorption on both the electrode potential and the solution composition are calculated for different electrode charges, ion sizes, and capacitance characteristics of the electric double layer.     

Synthetic oligonucleotides: AFM characterisation and electroanalytical studies

One of the most important steps in designing more sensitive and stable DNA based biosensors is the immobilisation procedure of the nucleic acid probes on the transducer surface, while maintaining their conformational flexibility. MAC Mode AFM images in air demonstrated that the oligonucleotide sequences adsorb spontaneously on the electrode surface, showing the existence of pores in the adsorbed layer that reveal big parts of the electrode surface, which enables non-specific adsorption of other molecules on the uncovered areas. The electrostatic immobilisation onto a glassy carbon electrode followed by hybridisation with a complementary sequence and control with a non-complementary sequence was studied using differential pulse voltammetry and electrochemical impedance spectroscopy. Changes in the oxidation currents of guanosine and adenosine were observed after hybridisation events as well as after control experiments. Modification of the double layer capacitance that took place after hybridisation or control experiments showed that non-specific adsorption of complementary or non-complementary sequences occur allowing the formation of a mixed multilayer.     

As(V)在TiO2表面的吸附机理

用延展X射线吸收精细结构(EXAFS)光谱和密度泛函理论(DFT)研究了As(V)-TiO2体系的吸附机理. 离子强度变化对As(V)-TiO2体系吸附无显著影响, 表明吸附后形成了内层络合物. EXAFS结果表明, As(V)原子主要通过—AsO4上的O原子结合到TiO2表面上, 平均As-O原子间距(R)在吸附前后无明显变化, 保持在(0.169±0.001) nm. As-Ti层的EXAFS分析结果与DFT计算的吸附构型的As-Ti原子间距对照表明, 体系存在两种主要亚稳平衡吸附(MEA)结构, 即对应于R1=(0.321±0.002) nm 的双角(DC)强吸附构型和R2=(0.360±0.002) nm的单角(SC)弱吸附构型. 而且随着吸附量由9.79 mg·g-1增加至28.0 mg·g-1, 吸附样品中双角构型配位数与单角构型配位数的比值(CN1/CN2)从3.3降低到1.6, 说明双角亚稳平衡吸附结构在低覆盖度时占优势, 而在高表面覆盖度时单角亚稳平衡吸附结构占优势, 即在表面覆盖度较大时, As(V)在TiO2表面上倾向于形成单角构型.     

Preparation of nanoporous MgO-coated TiO2 nanoparticles and their application to the electrode of dye-sensitized solar cells

Sol-gel-derived Mg(OH)(2) gel was coated onto TiO(2) nanoparticles, and the subsequent thermal topotactic decomposition of the gel formed a highly nanoporous MgO crystalline coating. The specific surface area of the electrode that was prepared from the core-shell-structured TiO(2) nanoparticles significantly increased compared with that of the uncoated TiO(2) electrode. The increase in the specific surface area of the MgO-coated TiO(2) electrode was attributed to the highly nanoporous MgO coating layer that resulted from the topotactic reaction. Dye adsorption behavior and solar cell performance were significantly enhanced by employing the MgO-coated TiO(2) electrode. Optimized coating of a MgO layer on TiO(2) nanoparticles enhanced the energy conversion efficiency as much as 45% compared to that of the uncoated TiO(2) electrode. This indicates that controlling the extrinsic parameters such as the specific surface area is very important to improve the energy conversion efficiency of TiO(2)-based solar cells.