Structural and magnetic properties of Pt in Co/Pt multilayers

[Co(30 Å)/Pt(x Å)]₂₀ multilayers with the Pt layer thicknesses varying from 5 Å to 20 Å were characterized structurally by high angle X-ray diffraction, X-ray reflectivity, X-ray absorption spectroscopy and magnetically by X-ray magnetic circular dichroism. It is found that the structure and magnetic properties of Pt have a strong correlation with the Pt layer thickness. The 20 Å thickness Pt layer is not almost influenced by the adjacent Co layer and the nearest neighbors are dominated by Pt-Pt shells. With decreasing Pt layer thickness, the nearest neighbors are gradually dominated by Pt-Co shells and the Pt-Co intermixing regions also remarkable increase at the interfaces, especially for the 5 Å thickness Pt layer. The orbital and spin magnetic moments as well as the ratio m_orb/m_spin all decrease systematically with increasing Pt layer thickness, indicating that the interface atoms are polarized by direct Pt-Co hybridization, but that the adjacent layers are polarized by Pt-Pt interactions.     

Exchange coupling and remanence enhancement in nanocomposite Nd–Fe–B/FeCo multilayer films

Nd–Fe–B-type hard phase single layer films and nanocomposite Nd₂₈Fe₆₆B₆/Fe₅₀Co₅₀ multilayer films with Mo underlayers and overlayers have been fabricated on Si substrates by rf sputtering. The hysteresis loops of all films indicated simple single loops for fixed Nd–Fe–B layer thickness (10 nm) and different FeCo layer thickness (d_FeCo=1–50 nm). The remanence of these films is found to increase with increasing d_FeCo and the coercivity decrease with increasing d_FeCo. It is shown that high remanence is achieved in the nanocomposite multilayer films consisting of the hard magnetic Nd–Fe–B-type phase and soft magnetic phase FeCo with 20 nm?d_FeCo?3 nm. The sample of maximum energy product is 27 MG Oe for d_FeCo=5 nm at room temperature. The enhancement of the remanence and energy products in nanocomposite multilayer films is attributed to the exchange coupling between the magnetically soft and hard phases.     

Low-frequency alternative-current magnetic susceptibility of amorphous and nanocrystalline Co60Fe20B20 films

This investigation experimentally studies the low-frequency alternating-current magnetic susceptibility (χ_ac) of amorphous and nanocrystalline CoFeB films by measuring the magnetic field established by passing currents of various frequencies through such films of various thicknesses (t_f). A CoFeB film is sputtered onto a glass substrate with t_f from 100 Å to 500 Å under the following conditions: (a) As-deposited films were maintained at room temperature (RT) and (b) films were post-annealed at T_A=150 °C for 1 h. The samples thus obtained are analyzed in a magnetic field that was generated by an alternating current (AC) at various frequencies from 10 Hz to 25,000 Hz. The experimental results demonstrate that the χ_ac declines as the thickness of the as-deposited sample and the post-annealed sample (T_A=150 °C) increases because the lower coercivity (H_c) of thinner CoFeB films is similar to a soft magnetic characteristic and is associated with a higher χ_ac value. The best χ_ac value is obtained at a thickness of 100 Å under both conditions. The χ_ac value of the post-annealed sample exceeds that of the RT sample at thicknesses from 100 Å to 500 Å because the magneto crystalline anisotropy of the post-annealed sample yields the highest χ_ac value at the optimal resonance frequency (f_res), at which the spin sensitivity is maximal. The X-ray diffraction patterns (XRD) of as-deposited CoFeB films reveal their amorphous structure. The XRD results for the post-annealed films include a main peak at 2θ=44.7° from the body-centered cubic (BCC) nanocrystalline CoFe that indicated a (110) textured structure. Post-annealing treatment caused that the amorphous structure to become more crystalline by a thermally driven process, such that the χ_ac value of the post-annealed sample exceeded that of the RT sample. This experimental result demonstrates that the χ_ac value decreased as the thickness of the thin film increased. Finally, the CoFeB thin films had the best χ_ac at low frequency (<50 Hz) following post-annealing treatment. The results obtained under the two conditions indicate that the maximum χ_ac value and the optimal f_res of a 100 Å-thick CoFeB thin film were 1.6 and 30 Hz, respectively, following post-annealing at T_A=150 °C for 1 h, suggesting that a 100 Å-thick CoFeB thin film that has been post-annealed at T_A=150 °C can be utilized as a gage sensor and in transformer applications at low frequencies.     

Investigation of ferromagnetic coupling between Co layers in a Co/Pt multilayer with perpendicular anisotropy

The coercivity of a Co/Pt multilayer with out-of-plane anisotropy can be lowered greatly if it is grown onto an ultrathin NiO underlayer . By making use of this characteristic, a series of samples glass/NiO(10 Å)/[Co(4 Å)/Pt(5 Å)]₃/Pt(x Å)/[Co(4 Å)/Pt(5 Å)]₃ with different Pt spacer thickness have been prepared to determine the ferromagnetic (FM) coupling between Co layers across the Pt layer. The measurements of major and minor hysteresis loops have shown that the FM coupling between the top and bottom Co/Pt multilayers decreases monotonically with the Pt layer thickness and disappears above the Pt layer thickness of 40 Å. This thickness of 40 Å is much larger than that in the literature. In addition to the FM coupling between the top and bottom Co/Pt multilayers across the Pt spacer, there exists a weak biquadratic coupling, which induces the broad transition of the bottom Co/Pt multilayer.     

Tunneling magnetoresistance in exchange-biased CoFeB/AlOx/Co/IrMn junctions

A series of exchange-biased magnetic tunneling junctions (MTJs) were made in an in-plane deposition field (h) = 500 Oe. The deposition sequence was Si(1 0 0)/Ta(30 Å)/CoFeB(75 Å)/AlO_x(d Å)/Co(75 Å)/IrMn(90 Å)/Ta(100 Å), where d was varied from 12 Å to 30 Å. The MTJ was formed by the cross-strip method with a junction area of 0.0225 mm². The tunneling magnetoresistance (ΔR/R) of each MTJ was measured. The high-resolution cross-sectional transmission electron microscopic (HR X-TEM) image shows the very smooth interface and clear microstructure. X-ray diffraction (XRD) demonstrates that the IrMn layer of the MTJ exhibits a (1 1 1) texture. From the results (ΔR/R) increases from 17% to 50%, as d increases from 12 Å to 30 Å. The tunneling resistance (R_o) of these junctions ranges from 150 Ω to 250 Ω. The exchange-biasing field (H_ex) of the MTJ is 50-95 Oe. Finally, the saturation resistance (R_s) was measured as a function of the angle (α) of rotation, where α is the angle between h and the in-plane saturation field (H_s) = 1.1 kOe. The following figure presents the dependence of R_s on α, instead of originally expected independence, the curve actually varies with a period of π.     

Effect of Co layer thickness on structural and magnetic properties of C/Co/C films

Granular C/Co/C films have been prepared by magnetron sputtering from C and Co onto glass substrates at room temperature and subsequent in situ annealing. It has been found that the structure and magnetic properties of the C/Co/C films depend strongly on the Co layer thickness. Vibrating sample magnetometer measurements indicate that the in-plane coercivities reach maximum in 20 nm Co thickness of both as-deposited and annealed films. The squareness ratio of annealed films was more than 0.8. X-ray diffraction shows that majority Co nanograins are formed as the hexagonal-close-packed (HCP) structure in 20 nm Co thickness with annealing at 400 °C. Scanning probe microscope was used to scan surface morphology and magnetic domain structures. The values of the surface roughness were lower than 0.6 nm in all annealed samples. The average magnetic cluster size was estimated to be about 10 nm in annealed 20 nm Co thickness films.     

Dependence of magnetic properties on ferromagnetic layer thickness in trilayer Co/Ge/Co films with granular semiconducting spacer

We have investigated the magnetic properties of trilayer films of Co–Ge–Co. At a fixed thickness of germanium of 3.5 nm, the formation and distribution of metastable amorphous and cubic phases depends on the thickness of the ferromagnetic layer. The portion of the stable hexagonal phase is affected, too. Possible mechanisms for forming the observed magnetic structure are discussed.     

Magnetization reversal dynamics in Au/Co/Au(111) ultrathin films: Effect of roughness of the buffer layer

We present a study of the magnetization reversal dynamics in ultrathin Au/Co/Au films with perpendicular magnetic anisotropy, for a Co thickness of 0.5, 0.7 and 1 nm. In these films, the magnetization reversal is dominated by domain nucleation for t_Co=0.5, 0.7 nm and by domain wall propagation for t_Co=1 nm. The prevalence of domain nucleation for the thickness range 0.5-0.7 nm is different from results reported in the literature, for the same system and for the same thickness range, where the magnetization reversal took place mainly by domain wall motion. We attribute this difference to the effect of roughness of the Au buffer layer on the morphology of the magnetic layer.     

Effect of thickness on the structure, morphology and optical properties of sputter deposited Nb2O5 films

Nb₂O₅ films with the thickness (d) ranging from 55 to 2900 nm were deposited on BK-7 substrates at room temperature by a low frequency reactive magnetron sputtering system. The structure, morphology and optical properties of the films were investigated by X-ray diffraction, atomic force microscopy and spectrophotometer, respectively. The experimental results indicated that the thickness affects drastically the structure, morphology and optical properties of the film. There exists a critical thickness of the film, d_cri =2010 nm. The structure of the film remains amorphous as d < d_cri. However, it becomes crystallized as d > d_cri. The root mean square of surface roughness increases with increasing thickness as d > 1080 nm. Widths and depths of the holes on film surface increase monotonously with increasing thickness, and widths of the holes are larger than 1000 nm for the crystalline films. Refractive index increases with increasing thickness as d < d_cri, while it decreases with increasing thickness as d > d_cri. In addition, the extinction coefficient increases with increasing thickness as d > d_cri.     

Magnetic circular dichroism of [Co/Pd] and [CoB/Pd] multilayered films

Magnetic circular dichroism (MCD) and X-ray absorption spectra (XAS) at the Co L_2,3-edge of [Co/Pd]₂₀ and [CoB/Pd]₂₀ multilayered films, which were fabricated at 260 °C with different magnetic layer thicknesses (δ), have been measured. The lineshapes of XAS–MCD show that the electronic state of Co 3d of the films hardly changes even when sputtered at higher temperatures. The expectation values of orbital and spin angular momentum (〈L_z〉 and 〈S_z〉) are estimated using the sum rule, and it is found that 〈L_z〉/〈S_z〉 in δ<0.5 nm is larger than that in δ>0.5 nm.     

Early-stage ordering in in-situ annealed Fe51Pt49 films

We evidenced an early-stage ordering (ESO) in Fe₅₁Pt₄₉ film before the appearance of superlattice diffraction (long-range-order, LRO) using 40-nm-thick films prepared by magnetron sputtering onto quartz substrate. The appearance of L1₀ phase for samples deposited at substrate temperatures (T_s) 400 °C and higher was verified by X-ray diffraction. Surface roughness of Fe₅₁Pt₄₉ films, obtained via X-ray specular reflectivity with computational fitting, increases from 3.8 to 11 Å as T_s is increased from 25 to 275 °C. As further increase of T_s to 375 °C, the roughness drops to 3.2 Å and then increases again to 38 Å with T_s up to 700 °C. Measurement on residual strain demonstrates that it is initially compressive at T_s<400 °C. Thereafter the strain transfers to a tensile one and increases in magnitude as increasing T_s up to 700 °C corresponding to LRO transformation. Local atomic rearrangement is observed for samples deposited at T_s>250 °C by using extended X-ray absorption fine structure. Coercivity of films increases from 10 to 460 Oe as T_s increase from 25 to 375 °C (ESO) and then from 460 to 10,700 Oe with T_s 375-700 °C (normal LRO). The worked out quantitative estimation of ESO engages with that of LRO before T_s 400 °C.     

Effect of Co or Mn addition on the soft magnetic properties of amorphous Fe89−xZr11Bx (x=5, 10) alloy ribbons

The temperature and field dependent magnetic properties of melt-spun amorphous Fe_89−x−yZr₁₁B_x(Co,Mn)_y (x=5, 10 and 0≤y≤10) alloys in the temperature range 5-1200 K are reported. The Curie temperature and saturation magnetization at room temperature increase (decrease) almost linearly with Co (Mn) addition. With increasing Co concentration, the room temperature coercivity increases at the rate of 2.26 (0.28) A/m per at% for the x=5 (10) samples. The high-field magnetic susceptibility and local magnetic anisotropy decrease (increases) rapidly with increasing Co (Mn) concentration. The thermomagnetic curves show a marked increase in magnetization above 850 K corresponding to the crystallization of α-FeCo (α-Fe) phase in samples containing Co (Mn). The Curie temperature of the crystalline phase increases (remains same) with increasing Co (Mn) concentration with the formation of α-FeCo (α-Fe). Addition of Co up to 10 at% in Fe-Zr-B improves the room temperature saturation magnetization from 0.56 to 1.2 T, and Curie temperature from 315 to 476 K. Also, the coercivity increases with Co addition from 1.27 to 23.88 A/m for x=5 and from 7.64 to 10.35 A/m for x=10 alloy. The non-collinear spin structures that characterize Fe rich Fe-Zr-B amorphous alloys have been used to describe the observed results.     

Ordering temperature of L10-type FePt films reduced by CuO addition

Effects of addition of CuO layers in L1₀-type FePt thin films are investigated. The ordering temperature of L1₀-type FePt films can be reduced by CuO addition. The coercivities of 0.78 and 0.82 T are achieved in [Pt(10 Å)/Fe(14 Å)/CuO(2 Å)]₁₀ film annealed at 550 °C for 20 min and [Pt(10 Å)/Fe(15 Å)/CuO(3 Å)]₁₀ film annealed at 600 °C for 20 min, respectively, and these values are compared to the coercivity of 0.8 T in [Pt(10 Å)/Fe(13 Å)]₁₀ film annealed at 650 °C. The thickness of Fe and CuO layers strongly influences the ordering temperature of L1₀-type FePt and the magnetic properties of the films. The addition of CuO not only brings microstructure and surface morphology changes of FePt film, but also lowers the ordering temperature.     

Effect of nanoscale thin films of Dy2Fe14B on the magnetic hysteresis characteristics of melt-spun ribbons of Nd2Fe14B

The effectiveness of nanoscale Dy₂Fe₁₄B thin films on coercivity and energy product of melt-spun ribbons of Nd₂Fe₁₄B at high temperatures was investigated. It is hypothesized that the nanoscale Dy-thin film will act as an obstacle for the nucleation of reverse domains and also maximize the energy of domain walls and thereby improve the magnetic performance at high temperatures. Pulsed laser deposition (PLD) of amorphous Dy₂Fe₁₄B layers on Nd₂Fe₁₄B melt-spun ribbons was performed for a nominal thickness of 40 nm. The coated ribbons were then annealed in environmentally controlled quartz furnace at two different cycles (750 °C for 15 min and 900 °C for 2 h) to cause crystallization. Magnetic hysteresis tests conducted at 300 and 400 K revealed that there is small but consistent improvement in the magnetic properties of the coated ribbons annealed at 750 °C for 15 min. However, higher temperature annealing (900 °C for 2 h) drastically reduced the magnetic properties. The incomplete recrystallization of amorphous structure at 750 °C for 15 min and large grain growth and formation of non-magnetic phases at 900 °C for 2 h are believed to be responsible for not meeting the expected magnetic performance.     

Effect of Co layer thickness on the magnetic properties of Tb30Co70/SiNx/Co thin films

The SiN_x (20 nm)/Tb₃₀Co₇₀ (90 nm)/SiN_x (5 nm)/Co (3–37 nm)/SiN_x (10 nm)/Si multilayer films are deposited on naturally oxidized Si wafer by magnetron sputtering. The saturation magnetization (M_s) of the multilayer films is increased with the thickness of high M_s ferromagnetic Co layer. The perpendicular coercivity (_Hc⊥$H_{{\mathrm{c}}^{\perp }}$) value is increased with Co layer thickness as the thickness of the Co layer is lower than 15 nm and then decreases drastically when the thickness of the Co layer further increased. The increase of the _Hc⊥$H_{{\mathrm{c}}^{\perp }}$ value is owing to the interlayer exchange effect [Li Zhang, Physica B 390 (2007) 373] between TbCo and Co layers. Co under-layer with in-plane magnetic anisotropy would pin the magnetic moment of the TbCo layer near by the Co layer and cause the value of _Hc⊥$H_{{\mathrm{c}}^{\perp }}$ to increase. However, as the Co layer is thicker than a critical thickness, the _Hc⊥$H_{{\mathrm{c}}^{\perp }}$ value of the multilayer film would decrease. Therefore, the Co layer with in-plane magnetic anisotropy and soft magnetic properties is expected to dominate the magnetic properties of the multilayer films.     

Spin-pumping-enhanced magnetic damping in ultrathin Cu(0 0 1)/Co/Cu and Cu(0 0 1)/Ni/Cu films

The influence of the Cu capping layer thickness on the spin pumping effect in ultrathin epitaxial Co and Ni films on Cu(0 0 1) was investigated by in situ ultrahigh vacuum ferromagnetic resonance. A pronounced increase in the linewidth is observed at the onset of spin pumping for capping layer thicknesses d_Cu larger than 5 ML, saturating at d_Cu = 20 ML for both systems. The spin mixing conductance for Co/Cu and Ni/Cu interfaces was evaluated.     

Four-fold magnetic anisotropy in a Co film on MgO(0 0 1)

The development of devices based on magnetic tunnel junctions has raised new interests on the structural and magnetic properties of the interface Co/MgO. In this context, we have grown ultrathin Co films (≤30 Å) by molecular-beam epitaxy on MgO(0 0 1) substrates kept at different temperatures (T_S). Their structural and magnetic properties were correlated and discussed in the context of distinct magnetic anisotropies for Co phases reported in the literature. The sample characterization has been done by reflection high energy electron diffraction, magneto-optical Kerr effect and ferromagnetic resonance. The main focus of the work is on a sample deposited at T_S=25 °C, as its particular way of growth has enabled a bct Co structure to settle on the substrate, where it is not normally obtained without specific seed layers. This sample presented the best crystallinity, softer magnetic properties and a four-fold in-plane magnetic anisotropy with Co〈1 1 0〉 easy directions. Concerning the samples prepared at T_S=200 and 500° C, they show fcc and polycrystalline structures, respectively and more intricate magnetic anisotropy patterns.     

Characteristics of electron beam evaporated nanocrystalline SnO2 thin films annealed in air

Tin oxide (SnO₂) thin films (about 200 nm thick) have been deposited by electron beam evaporation followed by annealing in air at 350-550 °C for two hours. Optical, electrical and structural properties were studied as a function of annealing temperature. The as-deposited film is amorphous, while all other annealed films are crystalline (having tetragonal structure). XRD suggest that the films are composed of nanoparticles of 5-10 nm. Raman analysis and optical measurements suggest quantum confinement effects that are enhanced with annealing temperature. For instance, Raman peaks of the as-deposited films are blue-shifted as compared to those for bulk SnO₂. Blue shift becomes more pronounced with annealing temperature. Optical band gap energy of amorphous SnO₂ film is 3.61 eV, which increases to about 4.22 eV after crystallization. Two orders of magnitude decrease in resistivity is observed after annealing at 350-400 °C due to structural ordering and crystallization. The resistivity, however, increases slightly with annealing temperature above 400 °C, possibly due to improvement in stoichiometry and associated decrease in charge carrier density.     

Formation of Co ultrathin films on Si(1 1 1): Growth mechanisms, electronic structure and transport

The AES, EELS, AFM and resistance measurement investigations have been performed to determine the growth mechanism, electronic structure and resistance-thickness dependence of Co layers on silicon at the thickness range from submonolayer up to several monolayer coverage. These layers were obtained under UHV high-rate deposition with using re-evaporation of Co from a Ta foil. The layer-by-layer growth of Co on Si(1 1 1) with some light segregation of Si has been found on the AES data. An enlarged and reduced concentration of valence electrons in the interface Si layer at the thickness ranges 0-1 Å and in the Co film at d = 1-2 Å has been observed. Resistance measurement of the Co film showed a fast decrease of the resistance down to some value limited by quantum-size effect in accordance with the formation of a two-dimensional Co phase at d = 1-2 Å.