醇脱氢酶在反胶束溶液中的酶学性质研究

以十六烷基三甲基溴化铵(CATB)-辛烷-戊醇反胶束体系对醇脱氢酶(ADH)进行固定化,考察了pH、含水量、表面活性剂和助溶剂浓度对ADH固定化的影响。对游离酶和固定化酶的催化动力学性质研究表明:酶促反应的最适pH值均为9.0,最适温度分别是28℃和20℃,对乙醇的米氏常数分别为8.8mmol/L和5.5mmol/L。25℃时,游离酶存放120min约失活90%,而固定化酶仅失活30%,表明反胶束固定化ADH具有较好的热稳定性。     

反胶束固定化醇脱氢酶的制备及应用研究

研究十六烷基三甲基溴化铵(CTAB)-辛烷-己醇反胶束体系固定化醇脱氢酶(ADH)的制备及应用。考察了含水量、CTAB和己醇用量对于ADH固定化的影响。对游离酶和固定化酶的催化动力学性质研究表明:酶促反应的最适pH值分别为8.2和8.8,最适温度分别为31℃和20℃,米氏常数分别为12mmol/L和7mmol/L。30℃时,游离酶存放150min后失活90%,固定化酶失活50%,表明反胶束固定化ADH有较好的热稳定性。应用此体系测定了试样中乙醇的含量。     

醇脱氢酶在反胶束溶液中的催化动力学性质

以十六烷基三甲基溴化铵(CATB)-辛烷-己醇反胶束体系对醇脱氢酶(ADH)进行固定化,试验了含水量、酶液pH值、CTAB和己醇浓度对ADH固定化的影响。对游离酶和固定化酶的催化动力学性质研究表明：酶促反应的最适pH值分别为8.2和8.8,最适温度分别是31℃和20℃,对乙醇的米氏常数Km分别为12mmol/L和7.4mmol/L。在30℃时,游离酶存放150min后失活90%,固定化酶失活50%,表明反胶束固定化ADH有较好的热稳定性。     

固定化醇脱氢酶的制备及性质

以壳聚糖为载体,通过交联结合使醇脱氢酶(ADH)得以固定化。固定化的最适条件为:交联剂戊二醛浓度0.6%,pH值6.8,酶的偶联时间2.5h。对游离酶和固定化酶的动力学性质研究表明,酶促反应的最适pH分别为8.2和8.4,最适温度为34℃和35℃。酶的米氏常数为13mmol·L-1和48mmol·L-1。与游离酶相比,固定化酶在复用性上具有优势。应用固定化酶测定了试样中铬含量。     

反胶束固定化乳酸脱氢酶的催化动力学性质研究

以十六烷基三甲基溴化铵(CATB)-辛烷-己醇反胶束体系对乳酸脱氢酶(LDH)进行固定化,试验了含水量、CTAB和己醇浓度对LDH固定化的影响。对游离酶和固定化酶的催化动力学性质研究表明:酶促反应的最适pH值分别为9.2和9.5,最适温度分别是37℃和43℃,对乳酸的米氏常数Km分别为1.4 mmol/L和2.3mmol/L。30℃时,游离酶存放2 h,约失活50%,而固定化酶仅失活10%,表明反胶束固定化LDH具有较好的热稳定性。     

固定化酶法测定微量组分

以壳聚糖为载体对醇脱氢酶(ADH)和脲酶(UASE)进行固定化。固定化的最适条件:ADH和UASE的偶联时间分别为2.5h和1.5h,交联剂戊二醛浓度为0.6%和0.5%,偶联pH值为6.8和5.0。对游离酶及固定化酶的性质研究表明,ADH酶促反应的最适宜pH为8.0和8.4,最适宜温度为33℃和35℃,米氏常数为48mmol/L和13mmol/L;UASE酶促反应的最适宜pH均为7.0,最适宜温度为60℃和72℃,米氏常数为0.4mmol/L和2mmol/L。固定化酶与游离酶相比在复用性上具有优势,用固定化酶测定了试样中尿素含量以及模拟样中银离子含量。     

壳聚糖固定化醇脱氢酶的制备及其酶学性质研究

报道了醇脱氢酶(ADH)的固定化和酶学性质研究。以壳聚糖作为载体,戊二醛作为交联剂。固定化ADH的最适条件为:以6%戊二醛将壳聚糖交联2 h,与ADH反应2.5 h。对游离和固定化ADH酶学性质的研究表明:酶促反应的最适pH均为8.2,最适温度分别为37℃和40℃,对乙醇的表观米氏常数Km分别为33.9 mmol/L和46.2 mmol/L。与游离酶相比,固定化酶具有良好的操作稳定性。     

壳聚糖固定化乳酸脱氢酶的制备及酶学性质研究

以磁性壳聚糖作为载体,戊二醛作为交联剂,对乳酸脱氢酶(LDH)进行固定化.固定化的最适条件为:戊二醛浓度6%,pH值7.5,酶的偶联时间2 h.对游离及固定化LDH酶学性质的研究表明,酶促反应的最适pH值为9.2,最适温度分别为37℃和50℃,对乳酸的表观米氏常数分别为1.6 mmol/L和0.9 mmol/L.游离酶和固定化酶在40℃放置150 min后,其活力分别为最初的56.5%和76.1%.固定化酶在4℃贮存4周后,活力仍保留50%以上.固定化酶在室温下与底物重复反应6次后,活力仍保留60%以上,说明固定化酶具有较好的热稳定性、贮存稳定性和复用性.     

固定化脲酶的制备及应用

以壳聚糖作为载体,戊二醛作为交联剂对脲酶进行固定化。固定化的最适条件为:酶的偶联时间60min,戊二醛浓度0.5%,pH值7.0。对游离及固定化脲酶的酶学性质研究表明,酶促反应的最适pH均为7.0,最适温度分别为33℃和70℃。米氏常数分别为29.8mmol/L和13.9mmol/L。与游离酶相比,固定化酶的热稳定性和贮存稳定性更佳。应用固定化酶测定了试样中的微量组分。     

羰基还原酶CR2重组酶体系不对称合成(S)-N,N-二甲基-3-羟基-3-(2-噻吩)-1-丙胺

构建了羰基还原酶CR2重组酶体系,并优化了相关的酶促催化反应条件.通过在催化体系中添加辅酶NADP+(0.1 mmol/L)和辅底物葡萄糖(120 g/L),在30℃及p H=8.0的条件下反应4 h,CR2重组酶体系不对称还原N,N-二甲基-3-酮-3-(2-噻吩)-1-丙胺(DKTP,10 g/L),合成了高光学纯度(S)-N,N-二甲基-3-羟基-3-(2-噻吩)-1-丙胺[(S)-DHTP,e.e.值99.9%],产率为62%.在酶促催化过程中,由于辅酶循环生成葡萄糖酸导致反应体系p H值下降而影响催化效率.通过调控反应体系p H值,(S)-DHTP的产率提高到68%.不同浓度底物的反应过程表明底物对CR2酶促反应具有抑制作用,且在10 g/L底物浓度下反应的时空产率可达1.3 g·L-1·h-1.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.