天然石墨负极的改性研究

天然石墨作为锂离子二次电池负极材料得到了广泛关注. 针对天然石墨负极的体积效应和表面活性基团的不利影响, 通过溴化和高温煅烧处理制备石墨插层化合物中间体和适度膨胀的石墨样品以改善其倍率和循环寿命. 样品利用X 射线衍射(XRD)、扫描式电子显微镜(SEM)和比表面积检测(BET)分析其结构特征, 结果表明膨胀石墨样品石墨层剥离晶粒增大. 恒流充放电和循环伏安扫描测试结果表明改性后的石墨样品其倍率性能和循环稳定性均得到明显改善.     

锂硫电池膨胀氧化石墨/硫复合正极材料的制备及其性能

以棒状石墨为原料,采用改良的Hummers法与热处理制备得到膨胀氧化石墨(E-GO),利用在酸性水溶液中归中化学反应的方法合成纳米尺寸的硫颗粒,使其嵌入到膨胀氧化石墨的内部,制备了膨胀氧化石墨-硫复合材料。采用红外光谱,X-射线光电子能谱表征了膨胀氧化石墨表面官能团的存在和种类;X-射线衍射分析结果表明生成的硫属于斜方晶结构;扫描电子显微镜和透射电镜分析证明了材料中硫的均匀分布。恒电流充放电结果表明该复合正极材料的首次放电容量为1 020 mAh.g-1,100周循环之后其容量还保持在650 mAh.g-1左右;材料的倍率性能和库伦效率优异,这可能得益于小尺寸的硫在材料中均匀分布,以及表面官能团对硫的固定化作用。     

改性可膨胀石墨的制备及在硬质聚氨酯泡沫中的阻燃性能

采用表面接枝硅烷偶联剂法将硼酸负载在可膨胀石墨(EG)表面制得了改性EG(MEG), 并考察了MEG在硬质聚氨酯泡沫(RPUF)中的阻燃性能. 利用扫描电子显微镜、 X射线光电子能谱、 傅里叶变换红外光谱、 膨胀试验及热失重分析对MEG进行了形貌、 元素组成及结构性能表征, 通过热失重分析、 极限氧指数(LOI)及锥形量热仪考察了RPUF/MEG的热稳定性及燃烧性能. 结果表明, 硼硅化合物作为硅硼陶瓷前驱体已负载在EG表面; MEG及RPUF/MEG体系膨胀炭层更为致密, 800 ℃时的残余量分别较EG和RPUF/EG提高了8.7%和3.7%; RPUF/MEG体系的LOI较RPUF/EG有所提高, 热释放速率峰值降低了10%, 产烟速率及CO生成速率均显著降低. RPUF/MEG阻燃性能的提高与MEG负载的硅硼陶瓷前驱体促进了阻燃RPUF各组分间的相互作用及增强了炭层的阻隔性有关.     

酚醛树脂包覆氧化天然石墨作为锂离子电池负极材料

天然石墨经过浓硫酸氧化处理,酚醛树脂包覆并高温碳化后形成具有核壳结构的碳包覆氧化天然石墨复合材料.采用扫描电子显微镜(SEM),透射电子显微镜(TEM),X射线衍射(XRD),激光显微拉曼光谱(Raman)等检测技术对氧化处理以及酚醛树脂热解碳包覆前后天然石墨材料的结构与形貌进行分析与表征.结果表明,氧化处理与适量的酚醛树脂热解碳包覆有效修复了天然石墨表面的一些缺陷结构,使其表面更为光滑.电化学测试结果显示,经过氧化处理与酚醛树脂热解碳包覆后天然石墨材料电化学性能得到明显提高.酚醛树脂包覆量为9%时,复合材料表现出最好的电化学性能,其首次放电比容量为434.0mAh·g-1,40次循环后,放电比容量保持在361.6mAh·g-1,而未经处理的天然石墨放电比容量仅为332.3mAh·g-1.该改性方法有效提高了天然石墨材料的比容量,对其进一步应用具有重要意义.     

二元共聚物热解碳包覆的石墨负极材料

以苯萘二元共聚物包覆天然石墨后进行热处理，用所制备的包覆石墨作为锂离子电池的负极材料，与包覆前石墨材料相比较，可逆容量提高了10％，不可逆容量降低了7％，循环性能也得到了大的改善. X射线分析表明，改性后该石墨晶体中三方石墨的含量增高.     

石墨及石墨/双马来酰亚胺减摩树脂复合材料的XRD研究

利用X射线衍射对鳞片石墨、可膨胀石墨、膨胀石墨和纳米石墨薄片以及石墨 /双马来酰亚胺、纳米石墨薄片 /双马来酰亚胺减摩复合材料进行了研究,探讨它们之间在结构上的关系以及以复合材料中双马来酰亚胺预聚体对石墨层间距的影响.实验结果表明:可膨胀石墨中插层剂的插入除了增大石墨层间距外,还减小相邻插层剂未插入的石墨层间距;膨胀石墨的结构除了保留强度很弱的石墨特征峰外,还有大量强度极其微弱、层间距大小不一的峰;超声波对膨胀石墨的结构有整合、均匀化作用;双马来酰亚胺预聚体不能插入鳞片石墨层间,而能插入纳米石墨薄片的层间.     

改性球形天然石墨锂离子电池负极材料的研究

将天然鳞片石墨制成球形石墨,在其表面包覆一层纳米非石墨化碳材料制成具有核壳结构的改性球形石墨。实验结果表明:此法显著提高了天然石墨的振实密度、可逆容量(达365mAh·g-1 ),首次库仑效率( >93% )和循环稳定性(循环500次后,容量保持率>80% )。分析并讨论了负极材料的结构及其与电化学性能的关系。     

电解氧化法膨胀石墨形成机理研究

采用现代测试方法对电解氧化法制备的膨胀石墨各阶段产物进行了表征 ,对其形成机理作了一些探讨。结果证实 ,在氧化过程中 ,层间表面的石墨被氧化后 ,与嵌入层间的H2 SO4、H2 O等生成层间化合物 ,该化合物瞬间受高热而分解 ,产生的推力使石墨沿C轴方向膨胀 ,而层平面碳 -碳结构未被破坏。     

膨胀石墨表面化学镀镍及性能

采用化学镀法对膨胀石墨表面镀镍. 对包覆后的样品进行了SEM、EDS、XRD、IR和磁性能表征. 结果表面,膨胀石墨表面被镍层均匀包覆,其质量分数镍占94.12%、磷占5.88%,镀覆后产品在近红外波段反射率明显增大,磁性能明显增强,饱和磁化强度σs=26.3 A·m2/kg、剩磁σr=8.1 A·m2/kg、σr/σs=0.31,分析结果表明其属于软磁性材料.     

石墨层间化合物FeCl3-CrO3-GIC的制备及性能研究

以天然鳞片石墨、CrO₃、CH₃NO₂、FeCl₃为原料，按物质的量的比34∶1.5∶22∶1，利用化学氧化法制备出低温易膨胀、高膨胀容积的石墨层间化合物，300 ℃时膨胀容积为420 mL·g^-1，800 ℃时达到最大膨胀容积630 mL·g^-1，明显优于传统硫酸、硝酸插层的石墨层间化合物。采用SEM、EDS、FTIR、XRD、TG、VSM等技术对石墨层间化合物的组成、结构、性能进行了表征和分析。     

氧化石墨的制备及其有机化处理

Graphite oxide(GO) was successfully prepared by using expandable graphite， which is a new starting material instead of the normally adopted natural graphite. XRD and XPS data indicated that， in the same reaction condition due to the application of expandable graphite， the extent of oxidation for the product， GO， was considerably en-hanced and the period required for oxidation was greatly shortened. In addition， the prepared GO was modified by surfactant， that is the new sample， S-GO， was obtained. As a consequence the extended interlayer space has proved itself to be successfully intercalated by the surfactant.     

石墨氧化过程的XRD/XPS研究

石墨用强氧化剂如硝酸、高氯酸、氯酸钾或高锰酸钾等处理后,在石墨层间形成一种没有化学计量的层间化合物,通常叫做氧化石墨,又称石墨酸犤1犦。氧化石墨的研究历史可追溯到1855年犤2犦,期间,有关氧化石墨的制备及表征的报导获得了广泛的重视。就目前的研究现状而言,普遍认为化学法制备的氧化石墨中存在羟基、环氧官能团和双键结构犤3犦,这一结果已经得到广泛的证实,如FTIR犤4犦结果表明氧化石墨中含有C-OH、-OH、C=O等基团,13CNMR犤5犦也检测到与醚或羟基相联的碳原子,并发现sp2杂化的碳原子,元素分析的结果表明犤6犦,氧化石墨中的C/…     

三聚苯撑乙烯/蒙脱土发光光谱的时间依赖性

用原位插层法制备了插层型的三聚苯撑乙烯/蒙脱土(TPV/MMT)纳米复合材料. 研究了新制备及在室温储存180天后的TPV/MMT纳米复合材料的荧光光谱及蒙脱土层间距的变化情况. 荧光光谱分析表明, 储存180天后, TPV/MMT纳米复合材料的最大发射峰由494 nm蓝移到438 nm, 半峰宽由77 nm增加到104 nm. X射线衍射结果表明, 与新制备的复合材料相比, 蒙脱土的层间距由1.52 nm减小到1.22 nm. 红外光谱分析表明, 室温储存180天后的三聚苯撑乙烯苯环的某些特征峰由1598 和1554 cm-1分别红移到1506和1462 cm-1. 依据相关实验和理论数据探讨了储存180 天前后TPV在蒙脱土中聚集态结构的变化方式.     

The use of thermo-XRD-analysis in the study of organo-smectite complexes

Summary Thermo-XRD-analysis is applied to identify whether or not the adsorbed organic species penetrates into the interlayer space of the smectites mineral. In this technique an oriented smectite sample is gradually heated to temperatures above the irreversible dehydration of the clay, and after each thermal treatment is diffracted by X-ray at ambient conditions. In the thermal treatment of organo-clays, under air atmosphere at temperatures above 250°C, the organic matter is in part oxidized and charcoal is formed from the organic carbon. In inert atmosphere e.g. under vacuum above 250°C the organic matter is pyrolyzed and besides small molecules, charcoal is formed. If the adsorbed organic compound is located in the interlayer space, the charcoal is formed in that space, preventing the collapse of the clay. A basal spacing of above 1.12 nm suggests that during the adsorption the organic compound penetrated into the interlayer space. Thermo-XRD-analyses of montmorillonite complexes with anilines, fatty acids, alizarinate, protonated Congo red and of complexes of other smectites with acridine orange are described. To obtain information about spacings of the different tactoids that comprise the clay mixture, curve-fitting calculations on the X-ray diffractograms were adapted.     

Formation of organo-highly charged mica

The interlayer space of the highly charged synthetic Na-Mica-4 can be modified by ion-exchange reactions involving the exchange of inorganic Na(+) cations by surfactant molecules, which results in the formation of an organophilic interlayer space. The swelling and structural properties of this highly charged mica upon intercalation with n-alkylammonium (RNH(3))(+) cations with varying alkyl chain lengths (R = C12, C14, C16, and C18) have been reported. The stability, fine structure, and evolution of gaseous species from alkylammonium Mica-4 are investigated in detail by conventional thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), in situ X-ray diffraction (XRD), and solid-state nuclear magnetic resonance (MAS NMR) techniques. The results clearly show the total adsorption of n-alkylammonium cations in the interlayer space which expands as needed to accommodate intercalated surfactants. The surfactant packing is quite ordered at room temperature, mainly involving a paraffin-type bilayer with an all-trans conformation, in agreement with the high density of the organic compounds in the interlayer space. At temperatures above 160 °C, the surfactant molecules undergo a transformation that leads to a liquid-like conformation, which results in a more disordered phase and expansion of the interlayer space.     

Thermal stability of the layered modification of Cu0.5ZrTe2 in the temperature range 25–900 °C

The thermal stability of the layered modification of the Cu_0.5ZrTe₂ polycrystalline intercalation compound, synthesized at room temperature, has been studied in the temperature range 25–900 °C. A change in the occupation of the octahedral and tetrahedral coordinated sites in the interlayer space of the zirconium ditelluride was observed using in‐situ time‐resolved synchrotron X‐ray powder diffraction experiments. The formation of the rhombohedral CuZr₂Te₄ phase, which is stable in the temperature range 300–700 °C, has been observed. The copper intercalation at room temperature leads to the formation of a phase in which the Cu atoms occupy only octahedral sites in the interlayer space. At temperatures above the decay temperature of the rhombohedral CuZr₂Te₄, a layered phase with Cu atoms uniformly distributed between octahedral and tetrahedral sites in the interlayer space is stable. The changes in the crystal structure independent of temperature are in agreement with the previously proposed model, according to which the stability of the layered or the rhombohedral phase is determined by the entropy factor associated with the distribution of the intercalated atoms between the octahedral and tetrahedral sites in the interlayer space.     

A novel nanoporous graphitic composite

A novel nanoporous composite containing micrographitic carbon layers is synthesized by preliminarily expanding the interlayer of an oxidized product of graphite using surfactant, followed by Si bridging/pillaring, and carbonization.     

Model for the Thermal Expansion of Modified Graphite Nitrates

The thermal expansion of modified graphite nitrates was studied under close-to-equilibrium conditions. A model was proposed based on the expansion of a cavity in the sample similar to a Griffith crack. In accord with this model, the increase in the volume of the sample is proportional to the sixth power of the temperature due to the synergistic action of three factors: 1) accumulation of gas in the cavity, 2) increase in the temperature, and 3) decrease in the limiting pressure that the cavity can withstand without expanding.     

高频燃烧–红外吸收法测定石墨及其制品中的硫含量

建立高频燃烧–红外吸收法测定石墨及其制品中的硫含量。结合高频红外碳硫分析仪器特点,试验确定了方法的实验条件:试样粉碎至2.5 mm以下颗粒状,所有试样均为干燥状态,称样量控制在0.200 0~0.300 0 g之间,助熔剂为纯铁和钨粒,助熔剂添加顺序为纯铁+样品+钨粒。采用该方法对石墨标准样品进行测定,测定结果与标准值相符合,测定结果的相对标准偏差为0.86%~1.96%(n=10)。该法可用于石墨及其制品中硫含量的测定。