A synergistic flame retardant (silicon, phosphorus and nitrogen) based on cyclic polysiloxane, ammonium salt of tetramethylcyclosiloxyl-piperazin-phosphinic acid (APCTSi) was successfully prepared and firmly bonded to cotton fabric through a chemical grafting method. The chemical structure of APCTSi was characterized by Fourier transform infrared (FTIR) spectroscopy, 1H and 31P nuclear magnetic resonance (1H NMR and 31P NMR). The scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM–EDX) proved that APCTSi successfully adhered to the surface of cotton fabric and the elements on the surface of cotton fabric were evenly distributed. The flame retardant properties were characterized by limiting oxygen index (LOI), vertical burning test, thermogravimetric (TG) analysis and TG-FTIR. The limiting oxygen index (LOI) can reach 30.9% with a char length of 8.7 cm for the weight gain of APCTSi was 16.2%. The combustion behavior was characterized by cone calorimetry test. The peak heat release rate (pHRR) and total heat release (THR) values of treated cotton fabric decreased by 30% and 48% respectively compared to that of pure cotton fabric. All the results proved that the cotton fabric treated by APCTSi had the flame retardant effect of condensed phase (forming stable char layer) and gas phase (releasing nonflammable gases).
Graphic abstractWearable flexible sensors with quick response time and high stability are required in the fields of human motion detection, personal health monitoring, and artificial electronic skin. However, their design remains a challenge. To address this need, we fabricate a piezoresistive sensor with a wide detection limit, fast response time, and excellent stability in this work. Nickel (Ni) and copper (Cu) films are deposited on cotton fabric (CF) by in-situ polymerization of polyaniline (PANI) using magnetic filtration cathode vacuum arc deposition technology to obtain copper/polyaniline cotton (Cu/PANI/CF) and nickel/polyaniline cotton (Ni/PANI/CF). The pressure sensor is then fabricated by self-assembly. The proposed pressure sensor has a wide detection limit (0–180 kPa), rapid response time (30 ms), high cycle stability (>5000), and can detect the movement of each joint of the human body (such as the knee, finger, elbow, etc.). The sensor can also monitor different facial micro-expressions, including smiles and blinking. Based on the practical application of human motion signals and the detection of subtle stress, the proposed sensor demonstrates significant potential as a wearable electronic product for health monitoring.
Graphical abstractLife-threatening diseases, especially those caused by pathogens and harmful ultraviolet radiation (UV-R), have triggered increasing demands for comfortable, antimicrobial, and UV-R protective clothing with a long service life. However, developing such textiles with exceptional wash durability is still challenging. Herein, we demonstrate how to fabricate wash durable multifunctional cotton textiles by growing in situ ZnO-TiO2 hybrid nanocrystals (NCs) on the surface of cellulosic fabrics. The ZnO-TiO2 hybrid NCs presented high functional efficiency, owing to their high charge transfer/separation. Ultrafine fiber surface pores, utilized as nucleating sites, endowed the uniform growth of NCs and their physical locking. The resulting fabrics presented excellent UV protection factors up to 54, displayed bactericidal efficiency of 100% against Staphylococcus aureus and Escherichia coli, and optimum self-cleaning efficacy. Moreover, the functionalized textiles exhibited robust washing durability, maintaining antibacterial and anti-UV-R efficiency even after 30 extensive washing cycles.
Graphical abstractMultifunctional materials for water purification have attracted significant attention due to the increased water pollution problems. However, fabricating the low-cost, effective, and recyclable separation material for wastewater containing various hazardous substances is still a challenge. Herein, we developed an Ag/TiO2@PDMS coated cotton fabric with self-cleaning ability, high flux, superior visible-light photocatalytic ability, and recyclability via the “powder?+?glue” strategy. The composites are superhydrophobic (water contact angle 157°) and show high separation efficiency. After 20 times of repeated use, the separation efficiency remains 16,322 Lm?2 h?1, and methylene blue (MB) 's degradation rate remains almost unchanged. The high oil purification, catalytic property, excellent stability in harsh conditions, and recyclability enable the material as a satisfactory candidate for water purification.
Graphical abstractAn eco-friendly method for diversity-oriented synthesis of substituted dihydropyrano[2,3-c]pyrazole and benzylpyrazolyl coumarin derivatives has been achieved via one-pot and multicomponent reaction in the presence of PdO/Al-SBA-15 as an efficient and recyclable catalyst in H2O/EtOH under reflux conditions. The significant merits of this method are wide scope, high yields of the desired products, short reaction times and simple workup procedure. In addition, this nanocatalyst was simply recovered and reused five times without significant loss in catalytic activity and also performance.
Graphical abstractCellulose nanocrystals (CNCs) with high crystallinity exhibit high mechanical stiffness and strength. However, the high dispersibility of CNCs results in limited spinnability and orientation. In this study, oxidized nanocellulose was selected to obtain regionally oxidized CNCs (RO-CNC) with carboxyl groups appended. For the formation of orientable and extensible RO-CNC filaments, chitosan was introduced as the sheath solution to induce orientation by electrostatic action. The chemical structures were analyzed by Fourier transform infrared spectroscopy. The morphology of the oriented CNCs filaments was characterized by scanning electron microscopy and wide-angle X-ray scattering. Analysis of the relationship between the mechanical strength and the CNCs directional arrangement revealed that the mechanical strength of the composite fibers increased with the injection speed ratio as a result of the orientation of the RO-CNC. The mechanical strength of the oriented reinforced composite filaments reached as high as 104 MPa with an orientation index of 0.73. The tensile strength and elastic modulus of the filaments increased by 33% and 20%, respectively, compared to the unmodified CNCs spun fiber.
Graphic abstractIn this paper, several methods of hydrophobization of cotton fabrics using the thio-ene click reaction were compared. Durable, superhydrophobic textiles were obtained in an easy way. Various variants of functionalized silsesquioxanes were used for the hydrophobization of fabrics. The synthesis of bifunctional silsesquioxanes (RSiMe2O)4(ViSiMe2O)4Si8O12 and (RSiMe2O)4(R’SiMe2O)4Si8O12 were performed via hydrothiolation of silsesquioxane derivative (ViSiMe2O)8Si8O12. Alkoxysilyl, alkyl and fluoroalkyl moieties were introduced as functional groups. Samples were prepared using four methods, differing in the modification method and the number of stages. During the research, fabrics were modified via (a) the dip-coating process, (b) carrying out thiol-ene click reactions directly on the surface of the fabric and (c) using both of these methods. The hydrophobicity of the fabric was evaluated by measuring the Water contact angle (WCA). The obtained samples were also examined using infrared analysis (FT-IR), Scanning electron microscope (SEM), and Elemental analysis (SEM–EDS). All analyses were performed before and after the washing process in order to verify the stability of the performed modifications.
Graphical abstractThe complex anatomy of teeth limits the accessibility and efficacy of regenerative treatments. Therefore, the application of well-known inducers as injectable hydrogels for the regeneration of the dentin-pulp complex is considered a promising approach. In this regard, this study aimed to develop an injectable hydrogel containing mineral trioxide aggregate (MTA). The injectable chitosan/oxidized-nanocrystalline cellulose/MTA (CS/OCNC/MTA) hydrogels were prepared, and the physicochemical properties of these hydrogels were evaluated by TGA, FTIR, Rheological analysis, and SEM. Moreover, the effect of MTA on the swelling and degradability of scaffolds was assessed. The proliferative effects of synthesized hydrogels were also determined on human dental pulp stem cells (hDPSCs) by MTT assay. For induction of differentiation and biomineralization in these cells, the alkaline phosphatase activity and Alizarin Red S staining tests were performed in the presence of fabricated scaffolds. The proliferation of hDPSCs was significantly increased in the presence of these hydrogels. Moreover, the addition of MTA to hydrogel structure dramatically improved the differentiation of hDPSCs. These results suggested that this novel injectable hydrogel provides appropriate physiochemical properties and can be considered a promising scaffold for regenerative endodontic procedures.
Graphical abstractIn this, an efficient flame retardant composite has been prepared using biowaste derived phosphorous groups decorated graphene supported nanomaterial. The eggshell was utilized as a source of calcium carbonate, which was converted to monocalcium phosphate (CP) by phosphoric acid treatment. As-prepared monocalcium phosphate was functionalized with graphene to prepare graphene functionalized monocalcium phosphate (GCP). The GCP-coated fabric didn't ignite during the flame test and sustained more than 600 s on continuous exposure to flame without changing its initial length and shape. Whereas, graphene oxide (GO), and CP coated cotton fabric burnt out very easily within a short time. The efficient flame retardant property of as synthesized GCP coated cotton fabric was confirmed with a high limiting oxygen index (34.1) and char length of 2.5 cm was generated from the VFT test. The synthesized GCP coated cotton fabric also confirmed efficient flame retardant properties. This facile method enables an easy process for mass production of cost-effective, bio-waste derived nanomaterial for a significantly highly efficient candidate for different applications in sustainable chemistry, including flame-retardant applications.
Graphical abstractA green low-temperature deposition and crystallization method was developed to uniformly coat RuO2/TiO2 nanocomposite onto cotton fabrics for efficient solar photocatalysis. The sequential growth of anatase TiO2 and rutile RuO2 on the surface of the cotton was confirmed by XRD, Raman and XPS characterizations. After the deposition of RuO2, the optical properties of RuO2/TiO2/Cotton revealed better visible light absorption and higher charge mobility, and XPS spectra showed that the peaks of Ti 2p3/2 and O 1 s shifted towards the lower binding energies due to the interfacial charge transfer at the robust RuO2/TiO2 mediated with Ti–O–Ru bonding. The photocatalytic performances of the RuO2/TiO2/Cotton were evaluated towards the photodegradation of o-toluidine (o-TD), an aromatic amine widely used in the chemical industry. Compared with TiO2/Cotton, RuO2/TiO2/Cotton exhibited a remarkable improvement in the photocatalytic activity. The presence of RuO2 on the surface of TiO2/Cotton narrowed the band gap and improved the absorption of visible light. Moreover, the successful formation of a robust heterogeneous interface between TiO2 and RuO2 suppressed the charge carrier (e–/h+) recombination effectively. With the RuO2/TiO2 coating chemically bound to the cotton fibers, RuO2/TiO2/Cotton delivered long-term stability in photocatalytic activity and high mechanical durability even after 20 washing times. Our facile and scalable synthesis strategy paved a universal route to efficient immobilization of visible-light-responsible TiO2-based photocatalysts on the low-heat-resistant substrates for various applications.
Graphical abstractVulcanized fibers are all-cellulose materials made from cotton and/or wood cellulose after aqueous zinc chloride treatment. These materials were invented in the UK in the mid-nineteenth century and is widely used because of their excellent characteristics, such as impact resistance and electrical insulation. Recently the matured vulcanized fibers have been recognized as renewable and biodegradable materials and reevaluated with advanced cellulose technologies derived from cellulose nanofibers (CNFs) and all-cellulose composites. The microscopic analysis based on the improved freeze-drying method revealed that the strength of vulcanized fiber sheets can be attributed to the chemically defibrillated CNFs. The architecture is similar to all-cellulose composites made from the same raw materials in which the residual cellulose fibers serve as reinforcement, and the CNFs serve as adhesives or matrix components. In this report, we describe the history and structural characteristics of vulcanized fibers and introduce a new aspect in aqueous zinc chloride treatment of cellulose.
Graphical abstractIn this paper, we developed a microbial route to fabricate wood-inspired biomimetic composites comparable to natural wood. Focusing on the chemical composition of woody biomass, we performed in situ bioprocessing of bacterial cellulose (BC) imbibed in modified cationic lignin (Catlig), which exhibited significant bioactivity in improving the microbial growth dynamics. The structural and morphological characteristics were enhanced by the formation of hydrophobic and electrostatic interactions between BC and Catlig during biosynthesis. Microbially derived BC/Catlig composites exhibited enhanced thermal stability and crystallinity, with oriented cellulose fibers. The tensile properties, toughness, and specific strength of BC/Catlig composites were comparable to those of a heavy wood species (Zelkova serrata) under hydrated conditions and synthetic soft materials.
Graphic abstractExploitation of cotton fabric as electromagnetic interference (EMI) shielding substrates have attracted a growing interest due to their desirable low carbon footprint, economic feasibility, and sustainability. Herein, a facile strategy was proposed for preparing a cellulose-based multifunctional PNIPAAm/PPy hydrogel/cotton (PPHC) EMI shielding composites with simultaneous high-efficient electro-photo-thermal conversion and comfort regulation functions. The PPHC was fabricated via in situ polymerization conductive PPy hydrogel on cotton substrate followed by deposition of PNIPAAm. Benefiting from the unique interconnected three-dimensional networked conductive structure of PPy hydrogel, the obtained PPHC composites exhibited high conductivity (15 mS/cm), and EMI shielding effectiveness (EMI SE?~?40 dB) in the frequency of 8.2–12.3 GHz. Moreover, the PNIPAAm coating endowed the composite fabrics with adjustable wettability performance in response to external temperature, leading to excellent comfort regulation performance. This work provided feasible avenue toward low cost and sustainability cotton-based EMI shielding composites with efficient EMI shielding and comfort regulation performance.
Graphical abstractThe development of a simple surface barrier discharge plasma device is presented to enable more widespread access to and utilization of plasma technology. The application of the plasma device was demonstrated for pretreatment of wood prior to application of protective coatings for outdoor usage. The coatings' overall performance was increased, showing a reduction or absence of cracking due to weathering on plasma-pretreated specimens. Moreover, after ten months of outdoor weathering, the plasma-pretreated specimens showed fewer infections with biotic factors and improved adhesion performance in cross-cut tests, while the surface gloss performed independently from plasma pretreatment. In contrast to that, plasma-pretreated specimens were slightly more prone to discoloration due to outdoor weathering, whereas the plasma pretreatment did not impact the initial color after coating application.
Graphic abstractSurface modification of fabrics is a powerful strategy that can endow fabrics with desired effects while keeping the intrinsic properties. Herein, an ordinary strategy, dipping-drying based layer-by-layer self-assembly (LbL) coating, is reported to functionalize fabrics’ surfaces. Firstly, the novel cation waterborne polyurethanes (QAHDPU) and anion waterborne polyurethanes (HDPU) are successfully designed and synthesized. By incorporating targeted molecule, hydantoin diol (HD) and quaternary ammonium salt with long alkyl chain (DOQA), the QAHDPU are antibacterial and hydrophobically functionalized. Taking advantage of strong adhesion, waterborne polyurethanes (WPUs) are physically bonded to surfaces of fabrics to generate durable antibacterial and hydrophobic fabrics. The QAHDPU with long alkyl chain combined with rough and porous fabric surface fabricates hydrophobic fabric surface, which can prevent bacteria from adhering to the fabrics. Furthermore, the coated fabrics present excellent antibacterial properties after chlorination, forming a second barrier against bacteria. The chlorinated coated fabrics, can inactivate 85.0–99.9% of Staphylococcus aureus and 85.0–97.7% of Escherichia coli with contact time of 60 min. The hydrophobic properties of coated fabrics are greatly improved with water contact angles of 122.0°–141.1°. In addition, the proposed method is applicable for a variety of fibers and expected to be used for industrial production.
Graphical abstractCarbon quantum dots (CQDs) co-doped with N, P and S derived from expired milk was prepared by a simple hydrothermal method. By dipping pure cotton face towel (PCFT) into CQDs ink, a flexible all-biomass CQDs/PCFT sensor was prepared for the first time. Due to the heteroatom doping, extremely small particle size of CQDs and excellent permeability of CQDs/PCFT film, the flexible CQDs/PCFT sensor showed the high sensitivity and bending stability. In the range of 0–60° bending states, the responses of CQDs/PCFT sensor to four target analytes changed by less 5.0%. After 3000 bending of 60°, the maximum change of the response to the target analytes was only 6.4%. Interestingly, due to the abundant functional groups and defects of CQDs, the flexible CQDs/PCFT sensor displayed sensing curves of different shapes for different target analytes. In this way, by establishing a database of sensing curves of target analytes, multiple analytes can be detected discriminatively by relying only on single sensor with the help of image recognition. This work provided a reference for the development of cotton fiber based all biomass flexible gas sensor.
Graphical abstractThe development of eco-friendly corrosion inhibitors is a subject of several investigations, especially natural polymers. Aimed at suppressing the corrosion of L80 steel in 1 mol/L hydrochloric acid (HCl), a novel natural polymer inhibitor was developed based on xanthan gum (XG) and β-Cyclodextrin (β-CD) in this work. The corrosion inhibition effect of β-cyclodextrin modified xanthan gum (β-CD-XG) on L80 steel was evaluated by electrochemical methods, and surface analysis technology. Adsorption isotherm studies, Fourier transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS) were used to explore the corrosion inhibition mechanism of β-CD-XG on L80 steel. The results suggested that β-CD-XG was classified as a mixed-type inhibitor, and mainly suppressed the anode metal dissolution by a tight adsorption film. The formation of the film was attributed to the chemisorption of –OH, –COO-, –CH2–O–, and –CH2–O–CH2– groups on the surface of L80 steel, which conformed to the Langmuir adsorption model. The experimental results illustrated that the maximum corrosion inhibition efficiency of 94.74% was acquired at 200 mg/L β-CD-XG at 293 K.
Graphic abstractHerein, cellulose nanofibrils (CNF), alkali lignin (AL), and montmorillonite (MMT) were used to produce reinforced polyvinyl alcohol (PVA) hydrogels. The effects of MMT and AL contents on the rheological properties of reinforced hydrogel were studied. Compared with PVA/CNF hydrogel, the storage modulus of 40 wt% MMT-reinforced PVA hydrogel was increased by 41.4%. The rheological properties of MMT-enhanced PVA hydrogel could be adjusted by the variation of MMT loading. Also, as the PVA matrix had a synergistic effect with the embedded MMT and AL, the composite hydrogel demonstrated high efficiency in the removal of methylene blue dye (MB) from wastewater. Adsorption tests conducted at various time intervals (60–360 min) show that the hydrogels containing same content of MMT had higher removal efficiency. The MB adsorption of PVA/2CNF-0Li-40MMT was over 98.0%, whereas its adsorption equilibrium time and maximum adsorption capacity (qm) were 360 min and 67.2 mg/g, respectively. However, an extremely high content of MMT reduced the MB adsorption rate.
Graphic abstractHow to improve the flame retardancy of lyocell fibers has become an important issue in textile industry. Herein, lyocell fibers were firstly undergone etherification reaction between sodium chloroacetate and the hydroxyl groups of lyocell fibers to obtain carboxymethylated lyocell fibers (CM-lyocell), then the sodium ions of CM-lyocell were replaced by aluminum ions, and the flame retardant lyocell fibers (FR-lyocell) were prepared. Compared with lyocell fibers, the degradation temperature of FR-lyocell decreased by about 80 °C, and the char residue in nitrogen increased from 15.1 to 31.8 wt% at 800 °C. Importantly, the limiting oxygen index (LOI) value of FR-lyocell fabric was increased from 17.2 to 26.4%. Besides, the peak of heat release rate (PHRR) and total heat release (THR) of FR-lyocell had 77.4% and 76.3% reduction, respectively. The FR-lyocell can generate a highly graphitized char layer and release more water at high temperatures, which are beneficial to improving the flame retardancy of lyocell fibers. Moreover, the tensile test showed that the tensile strength of FR-lyocell decreased from 3.95 to 3.08 cN/dtex with a 22% reduction, showing good strength retention.
Graphic abstractMembrane applications for the separation of surfactant-stabilized emulsions are often constrained by a deficiency in permeability and anti-fouling properties. Herein, special wetted cotton fabric with a protective layer (P-MH@CF) for durable anti-fouling performance was synthesized by a two-step method, which was related to interfacial ion migration technology and unilateral spraying treatment. Permeability of water and separation performance of P-MH@CF membrane were investigated systematically. Emulsions stabilized by anionic, cationic, or non-ionic surfactant were successfully separated with high efficiency. In the process of separation, the oil droplets surrounded by surfactants were difficult to demulsify and gathered physically on the membrane surface to form a “cream layer”. The stearic acid acted as a protective layer, like a quilt, protecting the membrane from contamination. The membrane retained robust reusability for separation even after the “cream layer” had been washed off, which was promising for the remediation of oily wastewater containing surfactants.
Graphical abstract