聚苯乙烯大单体与乙酸乙烯酯的共聚及其接枝共聚物的表征

 研究了聚苯乙烯大单体与乙酸乙烯酯的溶液聚合,结果表明,接枝效率随引发剂用量、聚合温度及小单体与大单体的投料比的增加而增加,随大单体的分子量增加而减少,而随单体浓度的变化呈现一最大值。共聚过程中大单体的转化率开始较小单体的增加快,后期变慢。用萃取法纯化的接枝共聚物经GPC、IR、¹H-NMR及PGC等表征,并算得平均接枝数为4—7。透射电镜表明接枝共聚物中存在微观相分离。     

含规整聚氧乙烯支链的(丙烯酸丁酯-甲基丙烯酸甲酯)共聚物的合成表征及性质

研究了聚氧乙烯大单体与甲基丙烯酸甲酯及丙烯酸丁酯的三元共聚中大小单体的聚合速率和引发剂用量、大单体分子量及投料比对接枝效率及共聚物分子量的影响。用IR、~1HNMR、VPO、膜渗透压计及DSC等明确了经纯化过的共聚物为规整接枝共聚物,平均接枝数为10左右。研究其性能表明,该共聚物有一定的结晶度、良好的乳化性及相转移催化性,并呈现热塑性弹性体的性质。     

羧酸型接枝共聚物的合成及其络合物做化学阀

用大单体技术合成了带规整聚苯乙烯支链的聚丙烯酸接枝共聚物 .研究了各种聚合条件包括温度、时间、单体浓度、大单体分子量及大单体与小单体的投料比等对接枝效率、共聚物分子量的影响 .纯化的共聚物表现出良好的乳化性质及高吸水率 ,在稀溶液中的行为如同聚电解质 .此接枝共聚物与含规整聚氧乙烯支链的聚丙烯酸乙酯络合生成的大分子间络合物膜呈现化学阀的作用 ,水通过它的渗透速率能通过调节pH加以可逆地控制 .     

聚环氧乙烷大单体与丙烯酸乙酯的共聚及其规整接枝共聚物的表征

本工作研完了末端为甲基丙烯酸酯型的聚环氧乙烷大单体与丙烯酸乙酯的溶液自由基共聚。结果表明,大单体接枝效率和共聚物分子量受单体总浓度、投料比、大单体分子量及引发剂等的影响,接枝效率最高可达90％以上,分子量可在5-15×10~4范围内变化。丙烯酸乙酯与大单体共聚的竞聚率为0.83。共聚物用萃取法精制后,用IR、~1H-NMR、裂解色谱、GPC和膜渗透压计等进行了表征。证实产物有预期的规整接枝共聚物结构。平均接枝数为2—11。     

聚环氧乙烷大单体与丙烯酸乙酯的共聚及其规整接枝共聚物的表征

 本工作研完了末端为甲基丙烯酸酯型的聚环氧乙烷大单体与丙烯酸乙酯的溶液自由基共聚。结果表明,大单体接枝效率和共聚物分子量受单体总浓度、投料比、大单体分子量及引发剂等的影响,接枝效率最高可达90％以上,分子量可在5-15×10⁴范围内变化。丙烯酸乙酯与大单体共聚的竞聚率为0.83。共聚物用萃取法精制后,用IR、¹H-NMR、裂解色谱、GPC和膜渗透压计等进行了表征。证实产物有预期的规整接枝共聚物结构。平均接枝数为2—11。     

丙烯酸聚氧乙烯酯单体接枝聚乙烯共聚物的制备与表征

采用含α-双键的4种不同结构的聚氧乙烯型单体:丙烯酸聚氧乙烯酯(PAA)、丙烯酸端甲氧基聚氧乙烯酯(PEA)、甲基丙烯酸聚氧乙烯酯(PMA)和甲基丙烯酸端甲氧基聚氧乙烯酯(PMEM)接枝改性线性低密度乙烯(LLDPE)和低分子量聚乙烯(LMPE).采用核磁共振波谱及红外光谱分析了接枝共聚物的结构,并研究了接枝单体中聚氧乙烯基团对接枝共聚物性能的影响.相同单体浓度下4种单体的接枝效率大小顺序为PAAPEAPMAPMEM.对产物流变性能的研究结果表明随着接枝率的增加,单体复合黏度和剪切变稀行为增加;示差量热扫描结果显示了接枝率较低时接枝单体起到异相成核作用而加速结晶.为了进一步观察接枝单体对聚乙烯链段微观结构的影响,通过偏光显微镜观察发现LMPE为短棒状结构,而接枝LMPE通过支链极性基团的相互作用而形成星形或树枝状的微胶束结构.接触角测试表明,与LLDPE相比,高接枝率的LMPE改善亲水性的效果更好.     

含氟两亲接枝共聚物的制备及其与牛血清蛋白作用的研究

用端基反应法合成了对乙烯基苄基的聚乙二醇大分子单体,将该大分子单体与甲基丙烯酸六氟丁酯共聚,合成了一种含氟两亲接枝共聚物.利用1H-NMR1、9F-NMR、GPC对大分子单体和两亲接枝共聚物进行了表征.表面张力法测定了两亲接枝共聚物的临界胶束浓度,发现随着共聚物中含氟链段含量的增加,其临界胶束浓度降低.采用荧光光谱研究了含氟两亲接枝共聚物与牛血清蛋白(BSA)的相互作用,结果表明由于含氟链段疏水力的作用,含氟两亲接枝共聚物能与牛血清蛋白发生相互作用使其荧光增强,随着含氟两亲接枝共聚物浓度和共聚物中含氟链段含量的增加,荧光增强幅度加大.通过透射电子显微镜(TEM)和激光光散射粒度仪(PCS)测试发现,当BSA加入到含氟两亲接枝共聚物的胶束溶液后,所得胶束的粒径和粒径分布变大,共聚物胶束由规整的实心核壳结构变为囊泡状核壳结构.     

聚苯乙烯大分子单体与醋酸乙烯酯接枝共聚物的合成及表征

<正> 用大分子单体与小分子单体共聚是七十年代初才出现的合成接枝共聚物的一种新方法。通过共聚合反应而不是接枝反应同时形成主干及支链。这种接枝共聚物由于形成支链的大分子单体是预先合成的,其分子量分布较窄,又可调节控制,所以合成的接枝共聚物支链长短比较均一,副反应较少,链结构比较明确,因此也易于表征。     

侧链带羧酸基团聚甲基硅氧烷的合成及其共混物润湿性的研究

合成了单体烯丙氧基苯甲酸，通过接枝共聚合的方法把它接枝到含氢硅氧烷上，得到共聚物，这些共聚物具有较高的，Ｔｇ和热分解温度，在空气中热失重为２％，５％时相对应的分别为３５０℃和４８６℃，粘度测定表明，它们在低浓度时，η／Ｃ反应而较高，具有离聚物的溶液性能；把它作为增容剂与聚乙烯和尼龙６６在２６５℃下共混，该共混物恶性循环随尼龙６６含量的增加而增加。     

含氟两亲接枝共聚物的制备及其结晶行为

采用大分子单体技术合成了一系列以聚乙二醇为支链、甲基丙烯酸六氟丁酯为主链的含氟两亲接枝共聚物(PHFMA-g-PSPEG)。用1HNMR和凝胶色谱(GPC)对制备的大分子单体和两亲接枝共聚物的结构进行了表征。利用示差扫描量热法(DSC)、X射线衍射(XRD)和偏光显微镜(POM)测试技术对含氟两亲接枝共聚物的结晶行为进行了研究。DSC和XRD结果表明,随着共聚物中含氟链段质量分数的增加,其结晶温度(Tc)和结晶度(Xc)均降低,而结晶熔融温度(Tm)先减小后增加。POM发现,随着共聚物中含氟链段质量分数的增加,其结晶速度减慢,共聚物形成清晰球晶的能力减弱,当共聚物中含氟链段质量分数为57%时,含氟两亲接枝共聚物已不能形成清晰的球晶。     

EPR-g-PS接枝共聚物的大分子单体共聚物合成及表征

将阴离子聚合所得末端带有烯丙基的窄分布聚苯乙烯大分子单体(PSallyl)与乙烯、丙烯在钒催化体系下进行共聚合,得到聚苯乙烯(PS)支链沿乙丙橡胶(EPR)主干无规分布的接枝共聚物EPR-g-PS。接枝效率为70％左右。大分子单体的分子量、加入量,催化剂浓度和聚合温度等对共聚反应及其产物结构有明显的影响。丁酮为选择沉淀剂可分离未反应的聚苯乙烯大分子单体。用紫外光谱、核磁共振、渗透压和凝胶渗透色谱法测定了纯制接枝共聚物的组成和分子量。结果表明所合成的EPR-g-PS的聚苯乙烯含量为5—45％;支链为分子量1.0—7.8×10~4的窄分布((?)=1.05—1.17)聚苯乙烯;平均支链数为1—4。     

Synthesis, Purification and Characterization of Amphiphilic and Microphase Separated Graft Copolymer Polystyrene-g-Poly(ethylene oxide)

The present paper covers the poly (ethylene oxide) macromer with vinyl benzyl terminal group (PEO-VB) prepared by deactivation of the alkoxide function of mono-functional "living" PEO chains with vinyl benzyl chloride (VBC). The obtained macromers were subjected to careful purification and detailed characterization. A new kind of amphiphilic polystyrene-g-poly(ethylene oxide) (PS-g-PEO) with both mi-crophase separated and PEO side chains was synthesized from radical copolymerization of PEO-VB macromer with styrene monomer. An improved purification method, referred as "selective dissolvation", was established for the isolation of graft copolymers from the grafting products, and the purity and yield of the purified copolymers were satisfactory. The well-defined structure of the purified copolymers was confirmed by IR, 1H NMR and GPC. The bulk composition of the graft copolymers was determined by a well-established first derivative UV spectrometry. Various experimental parameters controlling the copolymeri     

SYNTHESIS OF POLYACRYLAMIDE WITH PENDANT POLY(BUTYL ACRYLATE) CHAINS USING THE MACROMER TECHNIQUE AND STUDIES ON THEIR PROPERTIES

INTRODUCTIONSince Milkovich and Chiang[1] developed a method of preparing copolymers with uniform side chains by usingthe macromer technique, the synthesis of copolymers with uniform side chains from different macromers hasbeen studied extensively. Milkovich et al. reported the synthesis of polystyrene macromer through termination ofliving polystyrene anions with methacryloyl chloride and its copolymerization with butyl acrylate to formthermoplastic elastomer[2]. Rempp[3] obtained polyoxy…     

Copolymerization reactivity of poly(methyl methacrylate) macromer

Poly(methyl mehtacrylate)(PMMA) macromers with several vinyl groups at both chain ends were synthesized by the mechanical scission reaction of the main chain in the presence of p-divinylbenzene(p-DVB). The radical copolymerization of this macromer with styrene(St) or MMA was carried out in benzene at 60°C and the reactivity ratio of both monomers (r₂) was calculated from a kinetic scheme of copolymerization. As a result, the effect of molecular weight and concentration of macromers was not observed in both copolymerization systems. The value of r₂, however, decreased as the number of end vinyl groups in a macromer (N) increased. These results are discussed in some detail as we describe the construction of the kinetic model of copolymerization.     

Ring-opening copolymerization of epoxy-terminated polystyrene macromer with epichlorohydrin and study on properties of the copolymers

The synthesis and ring-opening copolymerization of epoxy-terminated polystyrene (PS-ep) macromer with epichlorohydrin (ECH) as well as some properties of the graft copolymers, were studied. The results showed that content of the epoxy-terminated macromer in the crude macromer can be increased by anionic polymerization of styrene in cyclohexane, and capping with propylene sulfide, followed by termination with ECH at 0 °C. The ring-opening copolymerization of ECH with the macromer can be performed by using a quaternary catalyst system which was composed of triisobutyl aluminium-phosphoric acid-water-amine in the molar ratio of 1:0.25:0.25:0.1-0.15. When the charging weight percentage of PS-ep/ECH=25-65% and M_n of PS-ep was 2.6-10×10³, the conversion of ECH was greater than 95% and the conversion of the macromer or grafting efficiency was 35-65%. The purified copolymer was characterized by IR, ¹H NMR and dynamic viscoelastometer to be a copolymer of ECH with polystyrene (PS) grafts. Transmission electron microscope showed the existence of PS domains in the continuous phase of polyepichlorohydrin (PECH). In a certain range of compositions the graft copolymer behaves like a thermoplastic elastomer. The graft copolymer can be melted and processed repeatedly. Its oil and solvent resistance were better than PS and similar to PECH rubber. The graft copolymer can be used as a compatibilizer for blending PECH with PS to form thermoplastic elastomer blends. Only 2% of it based on the blend is needed to raise the tensile strength of the blends obviously.     

CHEMICAL MODIFICATION OF THE SURFACE OF CALCIUM ALGINATE GEL BEADS

The chemical modification of the surface of calcium alginate gel beads (CAGB) via grafting copolymerization with vinyl acetate (VAc) was studied. The optimum reaction conditions with activation and graft copolymerization two steps were explored. First, 5 grams CAGB with 2.5 mm initial diameter was initiated with 0.0493 mol/L K2S208 at 51℃ for 30 min in 15 mL 1% PVA/H2O. Then 4.34 mol/L VAc was added dropwise and the reaction was allowed to proce at 48℃ for 3 h. The grafting efficiency could come up to 30%. It was found the stability of modified CAGB in the air and in electrolyte solutions was greatly improved.