虾粉中总砷测定方法的探讨

用氢化物原子荧光光度法测定虾粉中总砷含量时,对干法灰化、湿法消解、微波消解3种样品处理方法对虾粉中砷元素测定结果的影响进行了比较。通过试验确定了最佳消解条件。砷元素浓度在0~10μg/L的范围内与荧光强度呈线性关系,线性相关系数r=0.999 6,检出限为0.2μg/L。比对结果表明,干法灰化适合于测定虾粉中总砷的含量,湿法消解测定总砷的含量偏低,微波消解不适合测定虾粉中总砷的含量。采用干法灰化-氢化物原子荧光光度法测定虾粉中总砷含量,加标回收率为76.2%~106.0%。     

Determination of Arsenic in Beverages and Foods by Hydride Generation Atomic Absorption Spectroscopy

Abstract

The determination of the arsenic content of foods and beverages by a technique involving a magnesium nitrate aided dry ashing step followed by an arsine generation atomic absorption finish is described. Recoveries of various arsenic species added prior to ashing was excellent. Total arsenic concentrations found in samples of beverages ranged from less than 10 to 265 ppb and in foods from 20 to 9290 ppb. The sensitivity of the technique is approximately ten-fold better than obtainable with commercially available hydride generation atomic absorption units.     

微波消解-高分辨连续光源原子吸收光谱法测定锁阳和韭菜籽中的重金属元素含量

利用微波消解-高分辨连续光源原子吸收光谱法测定锁阳、韭菜籽两种中药材中铜(Cu)、铅(Pb)、镉(Cd)、铬(Cr)、砷(As)和汞(Hg)的含量.采用微波消解进行样品前处理,火焰原子吸收法测定其中的Cu含量,石墨炉原子吸收法测定Pb、Cd和Cr含量,氢化物发生原子吸收法测定As、Hg含量.方法线性关系良好,相关系数R^2大于0.999,加标回收率为95.61%~100.1%,RSD为0.8%~3.3%,测得锁阳和韭菜籽中Cu、Pb、Cd、Cr、As和Hg的含量值均低于《药用植物及制剂进口绿色行业标准》和食品安全国家标准《食品中污染物限量》(GB2762-2012)中规定的限量指标.方法分析速率快、干扰少、精密度高,适用于中药材中重金属含量的测定.     

Automated microwave digestion of certifiable color additives for determination of mercury by cold vapor atomic absorption spectrometry

A procedure using an automated microwave flow digestion technique was developed and validated for the digestion of samples of certifiable color additives before mercury determination by cold vapor atomic absorption spectrometry. Recovery studies were performed by spiking most of the color additives subject to batch certification by the U.S. Food and Drug Administration with inorganic mercury (HgNO3) and with organic mercury (CH3HgCl). Successful recoveries of 72-113% Hg added at the 1 microg/g level were obtained. A method detection limit of 0.2 microg Hg/g was estimated from a Hg-spiked FD&C Yellow No. 6 sample. At the specification level of 1 ppm Hg (1 microg Hg/g), the 95% confidence interval was +/- 0.2 ppm (0.2 microg Hg/g).     

氢化物发生原子荧光法测定人发、玉米及辣椒中的砷

采用硝酸、高氯酸和硫酸湿法分解人发、玉米及辣椒,在盐酸介质中用硫脲-抗坏血酸将As(Ⅴ)还原为As(Ⅲ),氢化物发生原子荧光法测定,此法简便快速,相对标准偏差为2.4%。     

Determination of ultratrace bismuth in milk samples by atomic fluorescence spectrometry

A sensitive procedure was developed for determination of bismuth (Bi) in milk samples by hydride generation atomic fluorescence spectrometry (HG-AFS) after microwave-assisted sample digestion with HNO3 and H2O2. The method provides a sensitivity of 1832 fluorescence units (ng/mL) with a detection limit of 0.01 ng/mL, which corresponds to 20 pg absolute limit of detection, equivalent to 0.50 ng/g in the original sample. Application of the methodology to cow milk samples from the Spanish market showed the presence of Bi at a concentration of 11.8-28.8 ng/g, which compared well with data obtained after dry ashing of samples and with data obtained by inductively coupled plasma-mass spectrometry after microwave-assisted digestion.     

Determination of Bismuth in Geological Materials by Flow Injection Hydride Generation Atomic Absorption Spectrometry

Abstract

Flow injection analysis (FIA) has been applied to sample introduction in conjunction with automated hydride generation and AAS techniques for the determination of Bi in rock samples. The powdered rock sample is digested with a mixture of hydrofluoric, perchloric, and nitric acids. The evolved hydride is carried through to a heated quartz tube by a stream of argon, and the atomic absorption of Bi is measured at 223.2 nm.

Thiosemicarbazide and 1,10 - phenanthroline are used as masking agents to control interferences from Cu and Ni. The method permits the accurate determination of Bi in geological materials at levels as low as 10 ppb with an analysis rate of more than 50 digested samples per hour. Bi values on 13 international geological reference samples are reported.     

Preconcentration of traces of gold, silver and palladium on activated carbon and its determination in geological samples by flame AAS after wet ashing

A simple, rapid and cost effective preconcentration method is described for the determination of traces of gold (Au), silver (Ag) and palladium (Pd) in geological samples by flame atomic absorption spectrophotometry (AAS). The method is based on sorption of analytes (Au, Ag and Pd) on powdered activated carbon (AC) at pH 1 in hydrochloric acid (HCl) medium. The samples are decomposed by aqua regia — HCl treatment. The quantitative sorption (better than 92%) of analytes is obtained on AC (in absence of complexing agent), by simply manipulating optimal conditions. The unique feature of the method is, the analytes are recovered quantitatively from AC by oxidizing and completely solubilising the carbon using concentrated nitric acid (HNO₃) and perchloric acid (HClO₄) i.e. by wet ashing. The method of wet ashing has several advantages over conventional dry ashing. The accuracy of the method is evaluated by analysing, five Canada centre for mineral and energy technology (CANMET) standards; MA-3, MA-1b, FER-1, SU-1A, and CPB-1. In addition, ASK-3 and one inhouse standard, kolar gold field (KGF) samples was also analysed. As no standard for Pd is available, its accuracy was evaluated by standard addition method. The method was applied on numerous geological samples for the determination of Au, Ag and Pd down to 0.1 ppm (based on 10 g sample) within ±10% R.S.D. (n=5). The method could easily be adopted by any laboratory as the inputs are minimal (AC), inexpensive and easily available.     

Determination of traces of molybdenum in foods by electrothermal atomic absorption spectrometry

Low levels of molybdenum in different food samples were determined by atomic absorption spectrometry with electrothermal atomization after destruction of organic matter using four different methods, involving dry ashing at 600°C, wet digestion with heating with nitric/sulphuric and nitric/sulphuric/perchloric acid mixtures or direct extraction with dilute hydrochloric acid. In all cases the working conditions, reproducibility, precision and accuracy were investigated. The dry ashing method was generally the optimum destruction method.     

微波灰化-氢化物发生-原子荧光光谱法测定原油和燃料油中的铅和砷

探讨了使用微波灰化技术消化原油和成品油样品,并使用氢化物发生-原子荧光光谱法测定其中铅和砷的含量.研究了铅测定的灰化保护剂和砷测定的灰化助剂,并优化了仪器工作条件和实验条件.该方法测定原油和重油中铅的平均回收率分别为96.8%和96.7%,相对标准偏差分别为1.03%和0.93%;测定原油和重油中砷的平均回收率分别为90.0%和90.3%,相对标准偏差分别为2.39%和2.63%.     

Optimization and validation of arsenic determination in foods by hydride generation flame atomic absorption spectrometry

A hydride generation flame atomic absorption spectrometric method was developed and optimized to quantitate arsenic (As) in foods. A wet digestion of the samples with HNO3 + H2O2 was performed and excess oxidants were eliminated by addition of hydrochloric acid and urea. As5+ in As3+ was then reduced by potassium iodide. The As3+ solution was analyzed by generation of arsine with sodium tetrahydroborate. As determination ranged from 2.5 to 20 microg/L, with a determination coefficient of 0.997. The limits of detection (LOD) and quantitation (LOQ) were 0.6 and 2.1 microg/L, respectively. The method was validated and good results were obtained for recovery, precision, accuracy, LOD, and LOQ. This method is now used to analyze foods from Rwanda.     

ICP-AES测定铀污染土壤植物中铀的研究

采用电感耦合等离子体发射光谱(ICP-AES)对铀污染土壤植物中铀的测定方法进行了研究.在λU385.958 nm处,选择了仪器的最佳工作条件,考察了酸度和常见共存元素对测定的干扰情况,并且对比了干灰化消解和湿式消解对测定的影响.研究发现2%硝酸溶液为最佳介质,干扰离子对测定没有显著影响,干灰化消解比湿式消解得彻底.在选定条件下,方法检出限为0.18 mg·L-1,测定下限为0.61 mg·L-1,5.0000 mg·L-1的铀标准溶液的相对标准偏差RSD(n=10)为0.81%,方法回收率为96.2%～106.2%.该方法操作简单,快速.结果表明,用ICP-AES测定铀污染土壤植物样品中的铀是可行的.     

Extraction and Flameless AAS Determination of Germanium in Lignite Fly Ash

Abstract

The use of dicyclohexyl-18-crown-6 methyl isobutyl ketone solution in extraction and flamelessatomic absorption spectrophotometry (AAS) determination of germanium in lignite fly ashes have been studied.

Germanium is usually determined in lignites after the carbonaceous part of the sample has been burnt by a dry or wet ashing method. However, methods are described for direct determination of germanium.

In the present paper a wet ashing method is reported for the determination of germanium in lignite fly ashes by flameless AAS after extraction into dicyclohexyl-18-crown-6 methyl isobutyl ketone (MIBK) solution. Solvent extraction is a known hydrometallurgical method that could be applied in germanium recovery.     

Speciation of major arsenic species in seawater by flow injection hydride generation atomic absorption spectrometry

Arsenic present at 1 microg L(-1) concentrations in seawater can exist as the following species: As(III), As(V), monomethylarsenic, dimethylarsenic and unknown organic compounds. The potential of the continuous flow injection hydride generation technique coupled to atomic absorption spectrometry (AAS) was investigated for the speciation of these major arsenic species in seawater. Two different techniques were used. After hydride generation and collection in a graphite tube coated with iridium, arsenic was determined by AAS. By selecting different experimental hydride generation conditions, it was possible to determine As(III), total arsenic, hydride reactive arsenic and by difference non-hydride reactive arsenic. On the other hand, by cryogenically trapping hydride reactive species on a chromatographic phase, followed by their sequential release and AAS in a heated quartz cell, inorganic As, MMA and DMA could be determined. By combining these two techniques, an experimental protocol for the speciation of As(III), As(V), MMA, DMA and nonhydride reactive arsenic species in seawater was proposed. The method was applied to seawater sampled at a Mediterranean site and at an Atlantic coastal site. Evidence for the biotransformation of arsenic in seawater was clearly shown.     

Determination of total arsenic by batch hydride generation atomic absorption spectrometry in injectable drugs containing high levels of Sb(V) as N-methylglucamine antimonate

A procedure for the determination of arsenic by batch hydride generation atomic absorption spectrometry (HG AAS) in commercial samples of injectable drugs, containing high concentrations of Sb(V), is described. The procedure is based on the complexing effect for Sb of citric, oxalic and acetic acids as reaction media. Aqua regia was used for sample digestion prior to As determination by HG AAS. The following experimental conditions for the determination of total As, as As(V), were evaluated: the acid medium and its concentration, sodium tetrahydroborate concentration, purge time, and influence of the different oxidation states of As. The effect of the delay time after mixing of sample and acid solution was also studied. Optimized conditions were: 10% (m/v) citric acid, 1.5% (m/v) sodium tetrahydroborate solution and 30 s for purge time. A delay time of 1 h was required after the digested sample had been mixed with citric acid, before As determination could be carried out. No interference on As(III) and As(V) signals was observed in the presence of up to 1 mg Sb(V). The tolerance limits for Ni(II), Cu(II) and Pb(II) were 1 mg, 100 μg and 100 μg, respectively. Recovery tests for As(III) and As(V) resulted in values between 97 and 101%. Characteristic mass and detection limit (3σ), using the recommended conditions, were 0.52 and 0.8 ng, respectively, for total As.     

Comparison of dissolution procedures for the determination of cadmium and lead in plastics

Summary A microwave digestion procedure and an oxygen flask combustion procedure were developed for the determination of cadmium and lead in plastic materials. A comparison with conventional wet ashing shows acceptable agreement. Different types of plastics such as polyvinylchloride, polypropylene, polyethylene, polystyrene, polyamide, and polyethyleneterephthalate were investigated. The precision of microwave digestion was determined within a series and from day to day. The results obtained by flame atomic absorption spectrometry were verified by measurement with inverse voltammetry. Overall, microwave digestion as well as oxygen flask combustion are time saving and cost-effective dissolution procedures to supervise the legal cadmium limit in plastics.Abbreviations FAAS Flame atomic absorption spectrometry - GFAAS Graphite furnace atomic absorption spectometry - ICPMS Inductively coupled plasma mass spectrometry - PVC Polyvinylchloride - PP Polypropylene - PE Polyethylene - PS Polystyrene - PET Polyethyleneterephthalate - PA Polyamide 6.6 - PTFE-TFM Polytetrafluoroethylene-tetrafluoromethoxylate - HMDE Hanging mercury drop electrode - MS Mass spectrometry - OFC Oxygen flask combustion - MWD Microwave digestion - CWA Conventional wet ashing - DL Detection limit - QL Quantification limit     

火焰原子吸收法测定油画颜料中铅含量

采用干灰化法、湿氧化A法和B法分别对油画颜料进行消解后用原子吸收火焰法测定其中的铅含量.通过分析比较3种消解方法测定的结果,发现采用湿氧化法优于干灰化法,湿氧化A法优于B法.采用湿氧化A法对油画颜料进行加标处理后,加标回收率在90%-105%范围,表明采用该方法测定油画颜料中的铅含量是可信的.     

Determination of selenium in blood plasma and serum by flow injection hydride generation atomic absorption spectrometry

A flow injection hydride generation atomic absorption spectrometric (AAS) method has been used to determine the selenium concentrations of human serum and plasma samples following digestion with nitric, sulphuric and perchloric acids. In the hydride generation process, reduction was carried out by sodium tetrahydroborate to produce a hydride that was atomized in a flame-heated atomisation cell. The method had a detection limit of 1.2 ng ml-1 and a sensitivity of 2.1 ng ml-1. Within-run precisions of 5.8% at 20 ng ml-1 and 4.5% at 80 ng ml-1, and between-run precisions of 4.8% at 69 ng ml-1 and 3.4% at 80 ng ml-1 were obtained. An inter-laboratory comparison study with a graphite furnace AAS method was carried out and the results showed excellent agreement. The flow injection method of sample introduction allowed the use of a sample volume of 330 microliters with an injection rate of 90 injections per hour.     

Use of microwave digestion and atomic absorption spectrophotometry to determine chromic oxide as a digestibility marker in feed, feces, and ileal content.

Most conventional digestion procedures, such as dry ashing and wet ashing, are tedious and labor intensive. Microwave digestion is a good alternative, because microwave dissolution is faster, safer, and simpler, and provides more controlled reproducible conditions than conventional methods. The purpose of this study was to develop a microwave digestion method for mineralizing meat and bone meal diets, feces, and ileal contents. Each sample was heated on a hot plate for 10 min, dry ashed at 65 degrees C for 4 h, and transferred into microwave vessels. Then, 10 mL 70% HNO3 was added. Samples were digested for 7, 10, and 20 min at 95, 90, and 85% power, respectively. After the heating cycle, 6 mL 30% H2O2 was added, and samples were returned to the microwave for a second heating cycle of 1 and 7 min at 95% and 90% power, respectively. Finally, chromium concentration was determined by flame atomic absorption spectrophotometry. The digestion method was validated by using a standard reference material, SRM domestic sludge 2781, with a certified chromium value of 195 +/- 9 micrograms/g. The value obtained in this study was 178 +/- 11 micrograms/g, for a difference of 17 micrograms/g. Spike recovery experiments resulted in 103.16 and 100.35% recoveries of chromium from diet and feces samples, respectively. Coefficients of variation were 10.8 and 7.8%, respectively.     

Optimization of the determination of selenium in marine samples by atomic absorption spectrometry: Comparison of a flameless graphite furnace atomic absorption system with a hydride generation atomic absorption system

A comparison has been made between a graphite furnace system based on nickel as a matrix stabilizing metal and an automated hydride generation system with a heated quartz cell. The effect of nickel as a matrix modifier was studied in pure selenite solutions as well as in biological matrixes by different charring temperatures. The suppression effect of different acids on the response of the analyte is reported and discussed. The use of an electrically heated quartz tube as an alternative to the argon hydrogen flame method unproved the selenium determination by hydride generation atomic absorption. The effect of hydrochloric acid to secure quantitative formation of selenium (IV) and the interference of copper in the response measurements have been studied. Further a comparison has been made between three different digestion procedures when the hydride generation atomic absorption system was applied. The results of the graphite furnace atomic absorption and the hydride generation atomic absorption were found to be equally accurate, but the graphite furnace technique gave better reproducibility.