Determination of precious metals in geological samples by continuous powder introduction microwave induced plasma atomic emission spectrometry after preconcentration on activated carbon

A novel method was developed for analysing geological materials for Au, Ag, Pd and Pt by continuous powder introduction microwave induced plasma atomic emission spectrometry (CPI-MIP-AES). The preconcentration of the trace metals on activated carbon (AC) was performed before conducting MIP-AES measurements in order to obtain accurate and precise analytical results. The method proposed is based on the selective sorption of precious metals that are subsequently introduced to the plasma as a dry particulate aerosol consisted of analytes collected on the sorbent. The technical design and operating conditions of the novel sample introduction system based on the fluidized-bed concept has been optimized. The microwave excitation source with integrated rectangular cavity TE₁₀₁ and vertically positioned plasma torch has been used. The signal stability proved to be adequate for sequential mode of measurements due to the vertical plasma configuration as well as the MIP-AES system compatibility with the CPI technique. Calibration was done using home-made standards obtained by sorption of metals of interest from standard solutions on activated carbon. Precision is typically 1-4% relative standard deviation at the 1 μg g⁻¹ level. Under measurement conditions the detection limits for Ag, Au, Pd and Pt were 24, 43, 57 and 550 ng per 1 g of AC, respectively. The proposed procedure was used for Au, Ag, Pd and Pt determination in the platinum ore SARM-7 as well as Au and Ag in the Chinese soil GBW-07405 certified reference materials. The standard addition technique was used and recoveries revealed that the proposed method shows good accuracy and precision.     

Radiochemical neutron activation analysis for determination of Au,Ag, Pt and Pd in geological samples

A procedure for separation of Au, Ag, Pt, and Pd in geological samples has been developed. After irradiation, samples were fused with Na₂O₂ and silver was separated by filtering through a PbCl₂ filter in 4M nitric acid solution. Au, Pt and Pd were concentrated with rhodium and thiourea as rhodium sulfide and the separation process of these elements was carried out by a chromatographic method. Au, Pt and Pd were retained on a Dowex-1×8 anion column in 1M HCl. Pd was eluted from the column by using a mixture of 75% HCl acid-25% acetone. Au was eluted by using a mixture of 10% HCl-90% acetone. In the gold fraction, Pt was also determined through the photopeak of¹⁹⁹Au radionuclide (158 keV). The method was simple and rapid.     

Adsorption behavior of noble metal ions (Au, Ag, Pd) on nanometer-size titanium dioxide with ICP-AES.

The adsorption behavior of gold (Au), silver (Ag) and palladium (Pd) on nanometer-size titanium dioxide (NSTD) at low concentrations was studied using inductively coupled plasma atomic emission spectrometry (ICP-AES). A preconcentration procedure of the analytes was carried out using NSTD as a solid-phase extractant before their determination by ICP-AES. The optimum conditions for adsorption were studied in detail, and under the condition that Au, Ag and Pd ions could be adsorbed and recovered quantitatively. The static adsorption capacities of Au, Ag and Pd on NSTD were 22.63, 14.06 and 11.82 mg/g, respectively. For the elution of gold, silver and palladium, a mixture of 5% thiourea solution and 3 mol L(-1) HNO3 was used. The parameters tested included: pH conditions, contact time of the analytes with NSTD, flow rate, adsorption capacity and sorption kinetics. According to the definition of IUPAC, the detection limits (3sigma) of this method for Au, Ag and Pd with an enrichment factor of 50 were (0.016), (0.006) and (0.012) microg mL(-1), respectively, the relative standard deviations (RSD) were 8.7%, 4.5% and 7.4%, respectively (n = 6). Some geological samples were determined with satisfactory results.     

Highly efficient adsorbing noble metal ions by 3,4-dihydroxycinnamic acid-modified activated carbon

A method was established for the preconcentration of trace Au(III), Pd(II) and Pt(IV) by activated carbon modified with 3,4-dihydroxycinnamic acid. The separation and preconcentration conditions of analytes were investigated, such as effects of pH, the contacting time, the sample ?ow rate and volume, the elution condition and the interfering ions. At a pH of 1.0, the maximum static sorption capacity of the sorbent was found to be 374.8, 96.6 and 137.5 mg g^?1 for Au(III), Pd(II) and Pt(IV), respectively. The adsorbed metal ions were effectively eluted with 2.0 mL of 4% thiourea in 0.5 M HCl solution and determined by inductively coupled plasma optical emission spectrometry. The detection limit (3σ) of this method defined by IUPAC was found to be 0.12, 0.18 and 0.32 ?g L^?1 for Au(III), Pd(II) and Pt(IV), respectively. The relative standard deviation (RSD) was lower than 3.0% (n = 8) towards standard solutions. The method has been validated by analysing certified reference materials and successfully applied to the determination of trace Au(III), Pd(II) and Pt(IV) in road sediments samples.     

Synthesis and characterisation of morin-functionalised silica gel for the enrichment of some precious metal ions

Silica gel was firstly functionalised with aminopropyltrimethoxysilane obtaining the aminopropylsilica gel (APSG). The APSG was reacted subsequently with morin yielding morin-bonded silica gel (morin-APSG). The structure was investigated and confirmed by elemental and thermogravimetric analyses, IR and (13)C NMR spectral studies. Morin-APSG was found to be highly stable in common organic solvents, acidic medium (<2molL(-1) HCl, HNO(3)) or alkaline medium up to pH 8. The separation and preconcentration of Ag(I), Au(III), Pd(II), Pt(II) and Rh(III) from aqueous medium using morin-APSG was studied. The optimum pH values for the separation of Ag(I), Au(III), Pd(II), Pt(II) and Rh(III) on the sorbent are 5.7, 2.2, 3.7, 3.7 and 6.8, giving rise to separation efficiencies of 43.9, 85.9, 97.7, 60.9 and 91.0%, respectively, where the activity was found to be >90% in the presence of acetate ion. The ion sorption capacity of morin-APSG towards Cu(II) at pH 5.5 was found to be 0.249mmolg(-1) where the sorption capacities of Ag(I) and Pd(II) were 0.087 and 0.121mmolg(-1) and 0.222 and 0.241mmolg(-1) at pH 2.2 and 5.7, respectively. This indicates a 1:1 and 1:2 morin/metal ratios at pH 2.2 and 5.7, respectively. Complete elution of the sorbed metal ions was carried out using 10mL (0.5molL(-1) HCl+0.01molL(-1) thiourea) in case of Au(III), Pd(II), Pt(II) and Rh(III) and 10mL 0.5molL(-1) HNO(3) in case of Ag(I). Morin-APSG was successfully employed in the separation and preconcentration of the investigated precious metal ions from some spiking water samples yielding 100-folds concentration factor. The relative standard deviation (R.S.D.) and the T-test (|t|(1)) were calculated.     

Synthesis of rhodanine-bonded silica gel and its application in the preconcentration and separation of noble metals

A silica gel based sorbent containing rhodanine as functional group (RDSG) was prepared. Its adsorption and separation characteristics for Ag(I), Au(III) and Pd(II) were studied by flow-injection (FI) on-line preconcentration. Influence of different experimental parameters such as acidity, eluent, co-existing ions were investigated. Trace amounts of Ag, Au and Pd could be efficiently adsorbed by rhodanine-bonded silica gel from acidic solution and eluted with thiourea solution. Common co-existing ions exhibited virtually no interference to the preconcentration and determination. The adsorption capacity of RDSG was 0.0352, 0.107 and 0.122 mmol/g for Ag, Au and Pd, respectively. Detection limits of 0.004, 0.022 and 0.019 μg/mL for Ag, Au and Pd, respectively, were achieved with a sampling time of 60 s at a flow rate of 5.0 mL/min. The relative standard deviation were 0.5%, 0.9% and 1.7% for 0.040 μg/mL Ag, 0.200 μg/mL Au and 0.300 μg/¶mL Pd. The sorption property did not change after 1000 cycles of sorption-desorption. The contents of Ag and Au in three national certified ore samples and Pd in a secondary nickel alloy, an anode slime and a CoCl₂ electrolytic solution were determined. The results showed good agreement with the certified values.     

Synthesis of rhodanine-bonded silica gel and its application in the preconcentration and separation of noble metals

A silica gel based sorbent containing rhodanine as functional group (RDSG) was prepared. Its adsorption and separation characteristics for Ag(I), Au(III) and Pd(II) were studied by flow-injection (FI) on-line preconcentration. Influence of different experimental parameters such as acidity, eluent, co-existing ions were investigated. Trace amounts of Ag, Au and Pd could be efficiently adsorbed by rhodanine-bonded silica gel from acidic solution and eluted with thiourea solution. Common co-existing ions exhibited virtually no interference to the preconcentration and determination. The adsorption capacity of RDSG was 0.0352, 0.107 and 0.122 mmol/g for Ag, Au and Pd, respectively. Detection limits of 0.004, 0.022 and 0.019 microg/mL for Ag, Au and Pd, respectively, were achieved with a sampling time of 60 s at a flow rate of 5.0 mL/min. The relative standard deviation were 0.5%, 0.9% and 1.7% for 0.040 microg/mL Ag, 0.200 microg/mL Au and 0.300 microg/mL Pd. The sorption property did not change after 1,000 cycles of sorption-desorption. The contents of Ag and Au in three national certified ore samples and Pd in a secondary nickel alloy, an anode slime and a CoCl2 electrolytic solution were determined. The results showed good agreement with the certified values.     

Reductive coprecipitation as a separation method for the determination of gold,palladium, platinum,rhodium, silver,selenium and tellurium in geological samples by graphite furnace atomic absorption spectrometry

A method for the separation of Au, Pd, Pt, Rh, Ag, Te and Se from geological samples at trace levels is presented. The elements are separated from the matrix after dissolution by reductive coprecipitation using mercury as a collector and tin(II) chloride as a reductant. The efficiency of coprecipitation is studied by varying the acidity of the solutions and the amount of collector. The analyte elements are determined by graphite furnace atomic absorption spectrometry. In the determination of volatile elements (Te, Au and Ag), matrix modification with iridium is used. Selenium is determined with a mixed matrix modifier containing ascorbic acid and iridium. The method is tested by analysing geochemical reference samples.     

Interference-free determination of trace levels of gold and palladium in geological and metallurgical samples by flame atomic absorption spectrometry coupled with a flow injection on-line microcolumn preconcentration and separation system

A simple and highly selective method was developed for the routine determination of trace or ultratrace amounts of gold and palladium in geological and metallurgical samples. The method uses flow injection on-line preconcentration and separation with determination by flame atomic absorption spectrometry. Au and Pd in the sample are adsorbed on a 2-mercaptopyrimidine chemically modified silica gel (MPMSG) packed microcolumn in a 0.50M HCl medium and then eluted with 0.5 or 1.0% thiourea solution. The eluates are introduced into the flame atomic absorption spectrometer directly. With the use of a 0.85 mL microcolumn (about 0.14 g MPMSG packed), the present system tolerated concentrations of common base metal ions up to 25.0 mg/mL and concentrations of anions up to 100.0 mg/mL when Au(III) at 0.100 microg/mL and Pd(II) at 0.200 microg/mL were preconcentrated for 60 s with a sample flow rate of 5.0 mL/min. The limits of detection were 3.1 ng/mL for Au(III) and 6.1 ng/mL for Pd(II) with relative standard deviations of < or = 2.5%. The analytical results obtained by the proposed method for geological and metallurgical samples were in good agreement with the certified values.     

Analytical characterization of a silica gel sorbent with thioetheric sites

The sorption behavior of a newly synthesized silica gel sorbent with thioetheric sites (STS) towards microgram levels of Au(III), Pt(IV) and Pd(II) was studied. Au(III) is quantitatively (>95%) sorbed in the pH region of 1–9. The sorption of Pt(IV) starts at pH 1 and does not exceed 25% in the entire pH region examined. The sorption of Pd(II) starts at pH 7 and reaches 80% at pH 9. The sorption of Au(III) on STS at pH 1 is not affected by milligram amounts of Ni(II), Zn(II), Fe(III), Cu(II), Pb(II), Cd(II) or Co(II). Au(III) is quantitatively eluted with a 5% aqueous solution of thiourea. The adsorption capacity of STS towards Au(III) is 195 mg g⁻¹. The detection limit (DL) of Au(III) (3σ, n = 9) is 25 ng mL⁻¹. The RSD at a level of 10 × DL is about 2%. Solid-phase extraction of trace amounts of Au(III) on the STS sorbent, followed by its flame AAS determination in the eluate was applied to the determination of gold in geological samples. The results obtained for the gold content in the samples were in good agreement with those of the ICP-AES analysis.     

Single granular activated carbon microextraction and graphite furnace atomic absorption spectrometry determination for trace amount of gold in aqueous and geological samples

A new and simple method was developed for preconcentration trace amount of gold in aqueous and mineral samples. The method was based on the sorption of gold on granular activated carbon (AC) in acidic medium (hydrochloric acid) and subsequently direct determination by graphite furnace atomic absorption spectrometry (GFAAS). A small particle of adsorbent was delivered to small volume of sample. After extraction, AC removed and analyzed directly by GFAAS. Several factors influencing the extraction efficiency, such as the hydrochloric acid concentration, sample volume and extraction time were studied as well as effect of potential interfering ions. The preconcentration factor 50 was obtained. The limit of detection (LOD) of gold in water and soil samples was 0.007 μg L^− 1 and 0.9 ng g^− 1, respectively. The proposed method was applied successfully to the determination of trace amount of gold in environmental and geological samples. In order to validate the developed method, two certified reference materials: Platinum Ore (SARM-7B) and Copper Ore Mill Heads (No. 330) were analyzed and the determined values obtained were in good agreement with the certified values and recovery was obtained in the range of 80-118%. The relative standard deviations (RSD) for the spiking levels of 0.5 μg L^− 1 in the real samples was 4%, (n = 15).     

Determination of physiological noble metals in human urine using liquid-liquid extraction and Zeeman electrothermal atomic absorption spectrometry

An extremely sensitive, reliable and simple procedure is described for the determination of physiological palladium, platinum and gold in human urine. The urine samples were adjusted to pH 4 (Pd, Au) or pH 5 (Pt), followed by conversion of the analytes to their pyrrolidinedithiocarbamate complexes. These complexes were separated from the matrix by liquid-liquid extraction into 4-methyl-2-pentanone resulting in a 25-fold enrichment. Determination was by electrothermal atomic absorption spectrometry (ET-AAS) using longitudinal inverse alternating current Zeeman-effect background correction. The limits of detection calculated from three standard deviations of the blank values were 20 ng l⁻¹ for Pd and Au and 70 ng l⁻¹ Pt. Within-day precision (n = 10, 5 μg l⁻¹) ranged 5.2%–7.7%. The procedure is successfully applied to determine urinary palladium, platinum and gold in nine unexposed persons. Palladium levels in urine ranged < 20–80 ng l⁻¹ (arithmetical MEAN=38.7 ng l⁻¹), while gold levels ranged < 20–130 ng l⁻¹ (36.0 ng l⁻¹). Physiological platinum levels in urine were all < 70 ng l⁻¹. The accuracy of the procedure was checked by analyzing a series of urine samples by a second independent method (magnetic sector field inductively-coupled plasma-mass spectrometry) in combination with UV photolysis.     

Determination of platinum-group elements and rhenium in standard geological samples by isotope dilution with mass-spectrometric ending

A method is proposed for determining platinum-group elements, Ru, Pd, Os, Ir, Pt, and Re in geological samples by isotope dilution with mass spectrometric ending after sample decomposition with a mixture (1: 3) of conc. HCl + HNO₃ in a microwave system and the chromatographic separation of the analytes from the matrix on an AG 50W × 8 cation exchanger. The concentrations and isotope ratios are determined on high-resolution mass spectrometers ELEMENT and ELEMENT2. The attained detection limits range from 0.005 ng/g (Ir) to 0.2 ng/g (Pd) in solid samples. The use of isotope dilution improves the accuracy of determination and takes into account the matrix effect and changes in plasma parameters on the analytical signal. The method is tested in the analysis of standard samples of spinel lherzolite (GP-13) and serpentinite (UB-N). The relative standard deviation of the results of analysis is 5–22%, depending on the element and its concentration level (Ru, Pd, Re, Pt). In determining Os and Ir, a certain decrease in the accuracy and repeatability of the results is noticed.     

Synthesis of polyacrylaminoimidazole chelating fiber and properties of concentration and separation of trace Au, Hg and Pd from samples

A novel polyacrylaminoimidazole chelating fiber is synthesized simply and rapidly from nitrilon (an acrylonitrile-based synthetic fiber) and used for the preconcentration and separation of trace Au(III), Hg(II) and Pd(IV) ions from solution samples. The analyzed ions can be quantitatively concentrated by the fiber up to a flow rate of 15.0 mlmin(-1) at pH 3 and can also be desorbed with 15 ml of 4 M HCl+3% thiourea from the fiber column, with recoveries of 96.5-100%. The chelating fiber is reused ten times; the recoveries of these ions are still over 92%, and 100-1000 times of excess of Fe(III), Al(III), Ca(II), Mg(II), Ni(II), Mn(II), Cu(II), Zn(II) and Cd(II) causes no interference in the determination of these ions by inductively coupled plasma atomic emission spectrometry. The capacities of the fiber for the analytes are in the range of 1.56-2.92 mmolg(-1). The results show that the relative standard deviations for the determination of 50.0 ngml(-1) each of Au(III), Hg(IV) and Pd(IV) are in the range of 0.7-2.1%. The recoveries of a standard added in real solution samples are between 97 and 99%, and the concentration of each ion in powder sample detected by the method is in good agreement with the certified value.     

Sorption-luminescence determination of gold,silver, and platinum with the use of silica gel chemically modified with <Emphasis Type="Italic">N</Emphasis>-(1,3,4-thiodiazole-2-thiol)-<Emphasis Type="Italic">N</Emphasis>′-propylurea groups

Silica gel chemically modified with N-(1,3,4-thiodiazole-2-thiol)-N′-propylurea extracted gold(III) from solutions in the range of 6 M HCl-pH 8 and silver(I) from nitric acid solutions in the range of 6 M HNO₃-pH 8 and 1–2 M HCl at 20°C with 99.0–99.9% recovery and a sorption equilibration time of 5 min. Platinum(II) was quantitatively extracted at room temperature from solutions in the range of 4 M HCl-pH 8; the sorption equilibration time was 20 min. For the quantitative extraction of platinum(IV), it should be reduced to platinum(II). The intense yellowish orange luminescence (λ_max (Au) = 575 nm, λ_max (Ag) = 550 nm, and λ_max(Pt) = 620 nm) of surface complexes at 77 K under UV irradiation was used in the development of procedures for the low-temperature sorption-luminescence determination of gold, silver, and platinum. The detection limits were 0.15 (Au), 0.1 (Ag), and 0.05 μg (Pt) per 0.1 g sorbent. The calibration function was linear to 50 (Au, Ag) or 80 μg (Pt) per 0.1 g sorbent. The relative standard deviation in the determination of more than 5 μg of a metal was no higher than 6%. The sorption-luminescence determination procedures were tested in the determination of gold in gold-containing concentrates and their processing products and platinum in alumina-platinum catalysts.     

On-line preconcentration and determination of Au(III) in various environmental/industrial samples by flame atomic absorption spectrometry

A rapid and simple on-line method is described for the determination of Au(III) in various samples. The method is based on the sorption of gold(III) on Lewatit MonoPlus TP207 chelating resin including the iminodiacetate group, which is used as sorbent material and packed in a minicolumn. The chemical variables such as the pH of the sample solution, eluent type, interfering ions and concentrations of reagents, and instrumental variables such as sample loading volume, reagents flow rates, and tubing length, which affect the efficiency of the method were studied and optimised. Au(III) was sorbed on the chelating resin, from which it could be eluted with 3 mol L^?1 HCl, and then introduced directly to the nebuliser-burner system of FAAS. The limit of detection of the method was 0.2 µg L^?1 while the relative standard deviation was <4.0% for 20 µg L^?1 Au(III) concentration. The preconcentration factor was found to be 106 while the optimised sample volume was 15.3 mL. The accuracy of the method was verified by analysing the certified reference material. The developed method was applied successfully for the determination of gold in different samples with satisfactory results.     

Specificity of noble metals dynamic sorption preconcentration on reversed-phase sorbents

The reversible sorption preconcentration of noble metals (NMs) using different schemes “sorbent–reagent–eluent” was investigated. The extraction of Au, Pd, Pt, Ir, Rh and Ru chlorocomplexes from hydrochloric acid solutions on hyper-crosslinked polysterene MN-200 in the form of ion associates with tributylamine (TBA) and 4-(n-octyl)diethylenetriamine (ODETA) was investigated. It was found that Pd, Pt and Au were quantitatively and reversibly extracted using TBA on hyper-crosslinked polysterene; the appropriate eluent for desorption was 1 M solution of HCl in ethanol. Ir, Rh and Ru under these conditions were not sorbed quantitatively. It was found that sorbent hydrophobicity is not the main characteristic that defines the efficiency of sorption of a particular NM ion associate. Different efficiencies of hyper-crosslinked polysterene MN-200 for sorption of square-planar chlorcomplexes of Pt, Pd and Au and octahedral complexes of Ir, Rh and Ru were found. For the first time, the sorbents with their own N-atoms – StrataX and StrataX-AW – were used for the sorption of Ir, Rh and Ru. Using these sorbents, the sorption of Ir was increased up to 95%, and the sorption of Ru and Rh was increased to about 40%. We can explain these results by nonspecific interaction of chlorcomplexes of Ir, Rh and Ru with ethylenediamine groups of the sorbent. Weak bases with large anions may be applied for desorption of Ir, Rh and Ru. Two schemes of dynamic sorption preconcentration of NMs from hydrochloric acid solutions were proposed – hyper-crosslinked polysterene MN-200 for the determination of Au, Pd, Pt, and StrataX-AW for Ir, Rh and Ru.     

Determination of bismuth, indium and lead in geological samples by electrothermal AAS Part 2. Comparative study of palladium and molybdenum containing chemical modifiers*

A comparative and systematic study has been carried out of the effects of palladium and molybdenum containing chemical modifiers, such as Pd + Rh, Pd + Pt, Pd + Ru, Pd + Rh + Pt, Pd + Rh + Ru, Mo + Pd, Mo + Rh, Mo + Ru and Mo + Pt and additionally tartaric acid (TA) as a reducing agent together with mixed modifiers for the thermal stabilization of Bi, In and Pb in a Zeeman electrothermal atomic absorption spectrometer (ETAAS). The effect of the mass ratios of the mixed modifier components on the maximum pretreatment temperature for the analytes has been determined. The modifier mixtures of Pd + Rh + Pt, Mo + Pd + TA and Mo + Pt + TA were found to be especially powerful for the determination of Bi, In and Pb. These mixed modifiers could increase the ashing temperatures of the analytes up to 1250–1400° C. They were applied to the determination of Bi and Pb in dissolved geological reference samples and accuracy and precision of the method were thereby enhanced. The percent relative error was decreased from 20.0 to 0.4 for Bi and from 10.5 to 0.3 for Pb, depending on the sample type. Received: 9 May 1997 / Revised: 19 August 1997 / Accepted: 20 August 1997     

Electrothermal vaporization inductively coupled plasma atomic emission spectrometry determination of gold, palladium, and platinum using chelating resin YPA(4) as both extractant and chemical modifier

A new method for determination of trace gold (Au), palladium (Pd), and platinum (Pt) in environmental and geological samples by electrothermal vaporization (ETV)-inductively coupled plasma atomic emission spectrometry (ICP-AES) with the use of chelating resin YPA₄ as both solid phase extractant and chemical modifier has been developed. The resin loaded with analytes was prepared to slurry and directly introduced into the graphite furnace without any pretreatment. The factors affecting the vaporization behaviors of Au, Pd, and Pt were investigated in detail. It was found that, in the presence of YPA₄, Au and Pd could be quantitatively vaporized at lower vaporization temperature of 1900 °C. Compared with the conventional electrothermal vaporization, the vaporization temperature was decreased by 700 °C, and the detection limits for Au and Pd was decreased by a three-fold. However, a little effect of YPA₄ on the ETV-ICP-AES determination of Pt was found. Under the optimized conditions, the detection limits (3σ) of Au, Pd, and Pt for this method are 75, 60, and 217 pg, respectively; and their relative standard deviations (R.S.D.) are 4.4, 5.6, and 3.7%, respectively (n=9, C=0.2 μg ml⁻¹). The proposed method has been applied to the determination of trace Pd and Pt in sewage sludge, and the results well agreed with the recommended values. In order to further verify the accuracy of the developed method, a GBW07293 certified geological reference material and an auto catalyst NIST SRM 2557 reference material were analyzed, and the determined values coincided with the certified values very well.