Particle Breakup in Shock Waves Studies by single Particle Light Scattering

The breakup of suspended, agglomerated submicron particles was studied by exposing the aerosol to weak shock waves of varying strength under conditions 400 ms^?1?v?880 ms^?1. A newly developed laser light-scattering diagnostic employing a top hat laser profile was used to size the particles passing through a very small scattering volume. By Comparing the optically measured particle size in front of and behind shock waves, the breakup of agglomerated particles could be clearly identified. The experiments indicate that the aerodynamic forces behind an incident shock overcome the particle binding force resulting in disintegration of the submicron agglomerates. The results are presented in form of a modified Weber number.     

Investigation of the influence of humidity on the ultrasonic agglomeration of submicron particles in diesel exhausts

Removing very fine particles in the 0.01-1 micro m range generated in diesel combustion is important for air pollution abatement because of the impact such particles have on the environment. By forming larger particles, acoustic agglomeration of submicron particles is presented as a promising process for enhancing the efficiency of the current filtration systems for particle removal. Nevertheless, some authors have pointed out that acoustic agglomeration is much more efficient for larger particles than for smaller particles. This paper studies the effect of humidity on the acoustic agglomeration of diesel exhausts particles in the nanometer size range at 21 kHz. For the agglomeration tests, the experimental facility basically consists of a pilot scale plant with a diesel engine, an ultrasonic agglomeration chamber a dilution system, a nozzle atomizer, and an aerosol sampling and measuring station. The effect of the ultrasonic treatment, generated by a linear array of four high-power stepped-plate transducers on fumes at flow rates of 900 Nm(3)/h, was a small reduction in the number concentration of particles at the outlet of the chamber. However, the presence of humidity raised the agglomeration rate by decreasing the number particle concentration by up to 56%. A numerical study of the agglomeration process as a linear combination of the orthokinetic and hydrodynamic agglomeration coefficients resulting from mutual radiation pressure also found that acoustic agglomeration was enhanced by humidity. Both results confirm the benefit of using high-power ultrasound together with humidity to enhance the agglomeration of particles much smaller than 1 micro m.     

Two-stage vs. two-field electrostatic precipitator

The paper presents comparison of the collection efficiency of semi-industrial, two-field electrostatic precipitator and two-stage electrostatic precipitator comprising an electrostatic agglomerator. The two-stage electrostatic precipitator was converted from two-field electrostatic precipitator, in which the first field was replaced by unipolar electrostatic agglomerator. The investigated electrostatic precipitator was of parallel-plate type, with spiked-wire discharge electrode between sigma type collection electrodes. In the unipolar agglomerator used in this system, the particles were charged by ion current and forced to oscillate by alternating electric field. The oscillatory motion of particles perpendicular to the gas flow causes the collision between particles and deposition of small particles onto the larger ones. The agglomerated particles were next collected by one-field electrostatic precipitator.The collection efficiency of two-stage electrostatic precipitator for PM2.5 and PM1 particles was 99.1% and 98.8%, compared to 99% and 98.1% of two-field electrostatic precipitator, respectively. The most important result of this research is that the replacement of the first field of electrostatic precipitator by an electrostatic agglomerator does not change the overall collection efficiency of the system but the power consumption of electrostatic agglomerator can be 10–50 times lower than by the replaced field of electrostatic precipitator.     

Measurement of Inherent Material Density of Nanoparticle Agglomerates

We describe a new technique to measure the size dependent inherent material density of chain agglomerate particles. Measurements were carried out for diesel soot and aluminum/alumina agglomerate particles in the nanometer size range. Transmission electron microscopy was used to measure the volumes of agglomerate particles that were preselected by mass using an aerosol particle mass analyzer. We found that the density of diesel exhaust particles increased from 1.27 to 1.78g/cm³ as particle mobility size increased from 50 to 220nm. When particles are preheated to remove volatile components, the density was 1.77±0.07g/cm³, independent of particle size. The densities measured after heating correspond to the inherent material density of diesel soot. Measurements with aluminum nanoparticles were made downstream of a furnace where aluminum (Al) was converted to alumina (Al₂O₃). From measurements of inherent material density we were able to infer the extent of reaction, which varied with furnace temperature.     

Retrieval of aerosol physical and chemical properties from mid-infrared extinction spectra

We report several results that validate the accuracy of a retrieval method for the determination of a number of aerosol particle properties from their mid infrared (600-6000 cm⁻¹) extinction spectra. These properties include the number density, chemical composition, phase, size distribution, and to some extent, shape. The approach is based on information obtained in laboratory studies of micron-sized particles using the aerosol flow tube (AFT) technique. We report here experiments in which our method is used to measure a variety of aerosols including SiO₂ micro-spheres as well as solid NaCl, (NH₄)₂SO₄, ice and liquid water particles. The uncertainties in the retrieved aerosol properties associated with the particle shapes (spheres, spheroids, cylinders, hexagonal and rectangular prisms) as well as the effect of variations in the spectral range were evaluated. To assess the accuracy of the retrieved size distributions and particle shapes, the properties calculated from infrared spectra were compared with corresponding properties determined using alternative methods. We used scanning electron microscopy (SEM) for solid (NH₄)₂SO₄ and NaCl aerosols and direct particle imaging with an optical microscope assembly for liquid water aerosols. On the basis of the validation results, we discuss the boundaries of applicability of the most popular spectral model, single scattering by spherical, homogeneous aerosol particles.     

The aerosol penetration through an electret fibrous filter

The aim of this paper is to present a theoretical study of the aerosol penetration through an electret fibrous filter, using a numerical approach. The aerosol sizes considered in this study were in the submicron range, and in the numerical model, the conventional mechanical mechanisms (impaction, interception, diffusion and gravitationally settling) were taken into consideration along with the electrostatic mechanisms, including the Coulombic and dielectrophoretic effects. The aerosol penetration through an electret fibrous filter is heavily dependent on the aerosol penetration of a single fibre. The aerosol penetration through a single electret fibre under various filtration conditions was calculated. The effects of aerosol diameter, aerosol and fibre charge state, face velocity, packing density and aerosol dielectric constant on the aerosol penetration were investigated.     

Study of the mobility,surface area,and sintering behavior of agglomerates in the transition regime by tandem differential mobility analysis

The surface area of nanosized agglomerates is of great importance as the reactivity and health effects of such particles are highly dependent on surface area. Changes in surface area through sintering during nanoparticle synthesis processes are also of interest for precision control of synthesised particles. Unfortunately, information on particle surface area and surface area dynamics is not readily obtainable through traditional particle mobility sizing techniques. In this study, we have experimentally determined the mobility diameter of transition regime agglomerates with 3, 4, and 5 primary particles. Agglomerates were produced by spray drying well-characterised polystyrene latex particles with diameters of 55, 67, 76, and 99 nm. Tandem differential mobility analysis was used to determine agglomerate mobility diameter by selecting monodisperse agglomerates with the same number of primary particles in the first DMA, and subsequently completely sintering the agglomerates in a furnace aerosol reactor. The size distribution of the completely sintered particles was measured by an SMPS system, which allowed for the determination of the number of primary particles in the agglomerates. A simple power law regression was used to express mobility diameter as a function of primary particle size and the number of primary particles, and had an excellent correlation (R² = 0.9971) with the experimental data. A scaling exponent was determined from the experimental data to relate measured mobility diameter to surface area for agglomerates. Using this relationship, the sintering characteristics of agglomerates were also examined for varying furnace temperatures and residence times. The sintering data agreed well with the geometric sintering model (GSM) model proposed by Cho & Biswas (2006a) as well as with the model proposed Koch & Friedlander (1990) for sintering by viscous flow.     

Catalytic soot oxidation in microscale experiments: Simulation of interactions between co-deposited graphitic nanoparticle agglomerates and platinum nanoparticles

Continuously regenerating catalytic soot traps are under development to reduce particulate emissions from diesel exhaust. A good understanding of the processes that take place during soot oxidation is needed to optimize diesel soot trap performance. To gain insight into these processes from the perspective of nanoparticle technology, the effects of catalyst particle size and the interparticle distance between soot and catalyst particles were measured. A model catalyst was prepared by depositing Pt nanoparticles on a SiO/SiO₂-coated transmission electron microscope (TEM) grid. A soot surrogate composed of graphitic nanoparticle agglomerates generated by laser ablation was deposited on the same surface. This system simulates, morphologically, catalytic soot traps used in practice. The reaction was carried out in a tubular flow reactor in which the gas phase simulated diesel exhaust gas, composed of a mixture of 10% O₂ and 1000 ppm NO with the remainder N₂. The progress of the carbon nanoparticle oxidation was monitored off-line by analysis of electron microscopy images of the agglomerates before and after reaction. This experimental method permitted the correlation of reaction rate with particle sizes and separation distances as well as catalyst surface area in the direct environs of the soot particles. The experimental results revealed no effect of Pt catalyst particle size in the range 7–31 nm on the rate of reaction. Also observed were a decrease in the rate of reaction with increasing distance between carbon agglomerates and catalyst particles and a linear dependence of the reaction rate on the fractional catalyst surface area coverage.     

Comparison of nanoparticle measurement instruments for occupational health applications

Nanoparticles are used in many applications because of their novel properties compared to bulk material. A growing number of employees are working with nanomaterials and their exposure to nanoparticles trough inhalation must be evaluated and monitored continuously. However, there is an ongoing debate in the scientific literature about what are the relevant parameters to measure to evaluate exposure to level. In this study, three types of nanoparticles (ammonium sulphate, synthesised TiO₂ agglomerates and aerosolised TiO₂ powder, modes in a range of 30–140 nm mobility size) were measured with commonly used aerosol measurement instruments: scanning and fast mobility particle sizers (SMPS, FMPS), electrical low pressure impactor (ELPI), condensation particle counter (CPC) together with nanoparticle surface area monitor (NSAM) to achieve information about the interrelations of the outputs of the instruments. In addition, the ease of use of these instruments was evaluated. Differences between the results of different instruments can mainly be attributed to the nature of test particles. For spherical ammonium sulphate nanoparticles, the data from the instruments were in good agreement while larger differences were observed for particles with more complex morphology, the TiO₂ agglomerates and powder. For instance, the FMPS showed a smaller particle size, a higher number concentration and a narrower size distribution compared with the SMPS for TiO₂ particles. Thus, the type of the nanoparticle was observed to influence the data obtained from these different instruments. Therefore, care and expertise are essential when interpreting results from aerosol measurement instruments to estimate nanoparticle concentrations and properties.     

Calibration and numerical simulation of Nanoparticle Surface Area Monitor (TSI Model 3550 NSAM)

TSI Nanoparticle Surface Area Monitor (NSAM) Model 3550 has been developed to measure the nanoparticle surface area deposited in different regions of the human lung. It makes use of an adjustable ion trap voltage to match the total surface area of particles, which are below 100 nm, deposited in tracheobronchial (TB) or alveolar (A) regions of the human lung. In this paper, calibration factors of NSAM were experimentally determined for particles of different materials. Tests were performed using monodisperse (Ag agglomerates and NaCl, 7–100 nm) and polydisperse particles (Ag agglomerates, number count mean diameter below 50 nm). Experimental data show that the currents in NSAM have a linear relation with a function of the total deposited nanoparticle surface area for the different compartments of the lung. No significant dependency of the calibration factors on particle materials and morphology was observed. Monodisperse nanoparticles in the size range where the response function is in the desirable range can be used for calibration. Calibration factors of monodisperse and polydisperse Ag particle agglomerates are in good agreement with each other, which indicates that polydisperse nanoparticles can be used to determine calibration factors. Using a CFD computer code (Fluent) numerical simulations of fluid flow and particle trajectories inside NSAM were performed to estimate response function of NSAM for different ion trap voltages. The numerical simulation results agreed well with experimental results.     

Soot particle size modelling in 3D simulations of diesel engine combustion

The present work is focused on multi-dimensional simulations of combustion in diesel engines. The primary objective was to test, in a diesel engine framework, a soot particle size model to represent the carbon particle formation and calculate the corresponding size distribution function. Simulations are performed by means of a parallel version of the KIVA3V numerical code, modified to adopt detailed kinetics reaction mechanisms. A skeletal reaction scheme for n-heptane autoignition has been extended, to include PAH kinetics and carbonaceous particle formation and consumption rates: the full reaction set is made up of 82 gas species and 50 species accounting for the particles, thus the complete reaction scheme comprises 132 species and 2206 reaction steps. Four different engine operative conditions, varying engine speed and load, are taken into account and experimentally tested on a single cylinder diesel engine fuelling pure n-heptane. Computed particle size distribution functions are compared with corresponding measurements at the exhaust, performed by a differential mobility spectrometer.

A satisfying agreement between computed and measured combustion profiles is obtained in all the conditions.

A reasonable aerosol evolution can be obtained, yet in all the cases the model exhibits the tendency to overestimate the number of particles within the range 5–160 nm. Moreover calculations predict a nucleation mode not detected by the available instrument. According to the simulations, the total number and size of the nascent particles would not depend on the operative conditions, while the features of the larger aggregates distinctly vary with the engine functioning.     

CFD在燃煤细粒子凝聚过程中的应用

燃煤产生的细粒子富集了大量的有毒痕量元素,对大气环境和人类健康造成严重危害。本文针对燃煤细粒子的形成过程,在计算流体力学(CFD)的基础上,结合气溶胶动力学理论,模拟了烟气中细粒子在圆柱形流场中由于碰撞而凝聚的过程,并通过计算结果分析细粒子颗粒特征参量(速度、质量、直径和颗粒数目)随流场的变化趋势,为深入研究燃煤细粒子的形成演化机理提供理论基础。     

循环流化床收集器内颗粒团聚流动特性的研究

基于气固两相流理论和气溶胶动力学原理,建立流化床收集器(CFBA)内气体细颗粒聚团气固两相双流体模型。对不同入口气体速度、初始颗粒尺寸分布和不同颗粒团聚形成机理下收集器内颗粒聚团流动的流体动力特性进行数值模拟。研究结果表明湍流运动和剪切作用对颗粒聚团的形成起主要作用,布朗运动对颗粒团聚形成的影响可忽略不计。吸收颗粒可有效提高捕获细颗粒和颗粒聚团形成的能力。     

A Novel Method for Inhalation Control of Workplace Anthropogenic Pollutant Particles

This in vitro study investigated electrically charging effect on the deposition of inhaled workplace anthropogenic pollutant particles (APP) in a hollow throat cast model. Many occupational lung diseases are associated with exposure to workplace dust particles and other pollutants. Since the human throat is an effective filter, this study devised a novel idea of charging particles, and studying their deposition in the throat. Simulated workplace aerosol particles were generated from a commercially available nebulizer, and charged by a corona charger. Charged and uncharged particles were allowed to pass through a polyester resin cast of cadaver based throat, a replicate of a human oropharyngeal region. The aerosol particles' size and charge distribution were characterized by an Electronic Single Particle Aerodynamic Relaxation Time (ESPART) analyzer before and after passing the throat cast. The ESPART operates on the principle of Laser Doppler Velocimetry to measure simultaneously aerodynamic diameter and electrostatic charge on a single particle basis and in real time. The study results revealed that electrically charging increased agglomeration of smaller particles and increased deposition. Deposition of charged particles increased with increasing particle size which can be explained as the effect of inertial impaction.     

Surface science with aerosols

Experimental surface science with aerosol particles under atmospheric conditions is becoming a realistic possibility. The first part of this critical review focuses on nano-scopic aerosols generated in combustion of organic fuels at ambient pressures. The bizarre shape of soot agglomerates resists a simple definition of size and surface area. Yet a measure of the size known as the mobility diameter can be extracted from the mobility of the particles in their carrier gas. The total surface area must be divided into an active and a passive part. At the active surface, mass, energy, and momentum is exchanged with the molecules of the carrier gas. The active surface thus determines the dynamical properties of the particles. The passive surface is the surface enclosed in the interior as well as the surface in bays or cracks or, with larger particles, in the dead point of the laminar flow; it determines particle properties on a longer time scale. Simple automatic portable sensors measure the number density of airborne particles, their “size” and a characteristic fingerprint of the surface chemistry, making it possible to determine the source from which the particle was emitted. The response time of the sensors is ～1 s, hence one can monitor dynamical changes of the particles such as adsorption of water in the atmosphere. In the second part we examine a number of surface science techniques that have been used to characterize surfaces important to atmospheric chemistry in more detail, in particular the uptake of water and the influence of surfactants. We illustrate the application of these techniques to the investigation of alkali halide surfaces as a function of relative humidity. Finally we give first examples on how infrared spectroscopy and synchrotron-based ambient pressure X-ray photoelectron spectroscopy have been used to study more realistic aerosol particles, under conditions of ambient humidity. These examples show that in situ chemical analysis of the particles is possible with third generation synchrotron X-ray sources. In the near future, X-ray lasers might reveal the fast dynamics of chemical processes as well. Thus it is within reach to study aerosols under the conditions of the stratosphere. Stratospheric aerosols can reduce the insolation of the earth and may become one of the last resorts of humanity to counteract the effects of global warming.     

PM2.5气溶胶光学特性研究

利用FA-3型Anderson撞击式气溶胶粒度分布采样器采集大气中的可吸入颗粒物。在实验室使用光学测量系统对粒径低于PM2.5的气溶胶颗粒物进行透过率测量。结果表明,透过率随气溶胶粒子粒径的增大具有逐渐增加的趋势。粒径低于PM2.5的气溶胶颗粒与PM10粒径范围内的透过率相比,具有明显的波长选择性。     

Emission measurement and safety assessment for the production process of silicon nanoparticles in a pilot-scale facility

Emission into the workplace was measured for the production process of silicon nanoparticles in a pilot-scale facility at the Institute of Energy and Environmental Technology e.V. (IUTA). The silicon nanoparticles were produced in a hot-wall reactor and consisted of primary particles around 60 nm in diameter. We employed real-time aerosol instruments to measure particle number and lung-deposited surface area concentrations and size distribution; airborne particles were also collected for off-line electron microscopic analysis. Emission of silicon nanoparticles was not detected during the processes of synthesis, collection, and bagging. This was attributed to the completely closed production system and other safety measures against particle release which will be discussed briefly. Emission of silicon nanoparticles significantly above the detection limit was only observed during the cleaning process when the production system was open and manually cleaned. The majority of the detected particles was in the size range of 100–400 nm and were silicon nanoparticle agglomerates first deposited in the tubing then re-suspended during the cleaning process. Appropriate personal protection equipment is recommended for safety protection of the workers during cleaning.     

New technique to measure particle size using electrostatic sensor

A new technique is proposed to measure the particle mean size using an electrostatic sensor in frequency domain. This paper starts with a finite-element modeling simulator to model the induced electric charge of a ring electrode and to find the electrode sensitivity. The mathematical modeling was used to extract particle size information from the simulated signal in frequency domain. The method is applied in an experimental test where a low-noise signal conditioning was designed with a ring electrode as the electrostatic sensor. The method can be used to establish a cost effective size measurement system using electrostatic sensor.     

Aerosol Generation Method for Measuring Particles Suspended in Water – Detection of Particulate Impurities in Ultrapure Water and Sizing of Fine Powders –

The method described is based on the fact that the measurement of particles in the gaseous phase is generally easier than that in the liquid phase for fine particles smaller than 1 μm in diameter. The system consists of a liquid nebulizing unit, evaporator, condenser, mixing diluter and two different aerosol sizing instruments. It has been found that this method can continuously detect particulate impurities in ultrapure water in situ and can measure the size distribution of fine powders in the submicron particle size range down to about 0.05 μm.     

Agglomeration,isolation and dissolution of commercially manufactured silver nanoparticles in aqueous environments

The increasing use of manufactured nanoparticles ensures these materials will make their way into the environment. Silver nanoparticles in particular, due to use in a wide range of applications, have the potential to get into water systems, e.g., drinking water systems, ground water systems, estuaries, and/or lakes. One important question is what is the chemical and physical state of these nanoparticles in water? Are they present as isolated particles, agglomerates or dissolved ions, as this will dictate their fate and transport. Furthermore, does the chemical and physical state of the nanoparticles change as a function of size or differ from micron-sized particles of similar composition? In this study, an electrospray atomizer coupled to a scanning mobility particle sizer (ES-SMPS) is used to investigate the state of silver nanoparticles in water and aqueous nitric acid environments. Over the range of pH values investigated, 0.5–6.5, silver nanoparticles with a bimodal primary particle size distribution with the most intense peak at 5.0 ± 7.4 nm, as determined from transmission electron microscopy (TEM), show distinct size distributions indicating agglomeration between pH 6.5 and 3 and isolated nanoparticles at pH values from 2.5 to 1. At the lowest pH investigated, pH 0.5, there are no peaks detected by the SMPS, indicating complete nanoparticle dissolution. Further analysis of the solution shows dissolved Ag ions at a pH of 0.5. Interestingly, silver nanoparticle dissolution shows size dependent behavior as larger, micron-sized silver particles show no dissolution at this pH. Environmental implications of these results are discussed.