纳米铂-石墨烯修饰电极电化学检测1-羟基芘

该文以氧化石墨烯和氯铂酸混合液为前驱体,采用一步电沉积法制备了纳米铂/还原氧化石墨烯修饰电极(Pt/E-rGO/GCE),通过差分脉冲伏安法对1-羟基芘进行原位富集检测。结果表明,当溶液pH 2.0,制备Pt/E-rGO/GCE的电沉积圈数为5圈时,在50～700 nmol/L范围内,1-羟基芘浓度与还原峰电流呈线性关系,相关系数(r)为0.976,检出限(S/N=3)为12.1 nmol/L。该方法的稳定性、重现性及抗干扰能力良好,将其应用于尿样的检测,回收率为99.7%～108%,相对标准偏差为3.2%～4.2%。Pt/E-rGO/GCE的良好性能对电化学传感器的构建具有一定的实用价值。     

芦丁在铂纳米/碳纳米管修饰电极上电化学行为研究

通过电沉积的方式在多壁碳纳米管(MWCNTs)修饰玻碳电极表面上沉积铂(pt)纳米粒子,并运用循环伏安法(CV)、示差脉冲伏安法(DPV)探讨了芦丁在铂纳米/碳纳米管/玻碳电极上的电化学行为.实验结果表明,芦丁在该修饰电极上呈现一对良好氧化还原峰,其氧化峰电流与浓度在3.2×10(-8)～1.2×10(-5)mol/L...     

基于铂纳米颗粒电沉积镁铝水滑石修饰电极的电化学葡萄糖生物传感器

采用成核/晶化隔离法合成了镁铝水滑石纳米颗粒,将其修饰到氧化铟锡导电玻璃电极表面;在此修饰电极基础上,利用电沉积还原氯铂酸盐法制备了铂纳米颗粒/水滑石复合修饰电极.由于水滑石层板表面的外限域作用有效抑制了铂纳米颗粒的聚集,使该电极对过氧化氢具有较好的电催化性能.基于镁铝水滑石良好的生物相容性,将葡萄糖氧化酶进一步修饰到该电极表面,实现了对葡萄糖高灵敏的电化学检测,检出限(S/N=3)达1.0μmol/L.     

芦丁在纳米金修饰玻碳电极上的电化学行为及其测定

采用循环伏安法将纳米金电沉积于玻碳电极表面,制备了纳米金修饰玻碳电极(NG/GCE).在pH3.29的Britton-Robinson(B-R)缓冲溶液中,用循环伏安法研究了芦丁在NG/GCE上的电化学行为.结果表明,NG/GCE对芦丁的氧化还原反应有良好的电催化作用.用方波伏安法测得芦丁的还原峰电流与其浓度在2.0×10-8～2.0×10-6mol/L范围内呈线性关系,检出限为1.0×10-8mol/L(S/N=3).     

纳米金–壳聚糖修饰电极循环伏安法测定抗坏血酸

介绍纳米金–壳聚糖修饰电极的制备方法及其测定抗坏血酸的分析应用。采用电沉积方法,将氯金酸与壳聚糖的混合电解液直接共沉积,制备了壳聚糖–纳米金修饰玻碳电极的电化学传感器。利用循环伏安法研究了抗坏血酸浓度、p H值等对抗坏血酸在修饰电极上的电化学行为的影响。实验结果表明,修饰电极对抗坏血酸具有良好的电催化氧化作用,抗坏血酸浓度在5×10~(–5)~1×10~(–3) mol/L范围内线性良好,回归方程为I_p=0.433 8c+0.881 9,相关系数为0.998 71。该法可指导纳米金–壳聚糖修饰电极的制备及抗坏血酸含量的测定。     

甲醛在铂纳米颗粒修饰电极上的电化学响应及其应用

用铂纳米颗粒直接修饰玻碳电极,制成了具有大表面积的纳米铂修饰电极.该电极对甲醛的电催化氧化明显优于铂盘电极,电化学响应显著.在碱性介质循环伏安分析中,氧化峰电流与甲醛浓度呈良好的线性关系,检出限为3.8×10(-5)mol/L(1.3μg/L),且多次测量中甲醛氧化峰电流相对标准偏差为1.9%.该修饰电极可用于腐竹提取...     

复合铂纳米电极制备及其对H_2O_2的测定

基于丁烷高温裂解析碳的原理,采用气相裂解沉积法将碳纳米颗粒沉积到石英纳米管尖端,制备出碳纳米电极,采用循环伏安法将邻苯二酚聚合膜与铂纳米颗粒沉积至该碳纳米电极上,制备出了复合铂纳米电极。探究了不同制备条件的影响,确定了最佳制备条件,研究了该电极对痕量H_2O_2的检测,结果表明,在20～1000μmol/L浓度范围内,该电极对H_2O_2具有良好的线性关系,检出限为0.471μmol/L。该电极同时具备纳米电极和纳米孔道,为多功能一体化微纳集成系统的制作提供了一种新思路。同时由于该电极的纳米级尺寸(50～90 nm),可对活体生物组织/细胞进行微创无痕的实时在线检测,为直接测定活体组织体液及组织环境中H_2O_2含量提供了新方法。     

离子交换-电沉积法制备高Pt利用率多孔电极

采用离子交换-电沉积的方法(Ion-exchange/electrodeposition,IEE)制备了一种高Pt利用率催化电极,对所制备电极的表面形貌、催化活性及单电池性能用线性扫描伏安(LSV)、扫描电镜(SEM)、透射电镜(TEM)和单电池测试进行了表征. 结果表明,通过电极制备工艺和离子交换-电沉积参数的调控,能够消除碳载体表面官能团的影响,使铂阳离子只与全氟磺酸树脂(Nafion)上的H⁺进行交换. 在无铂离子的电解质中,将被交换的铂阳离子还原到与Nafion接触的碳载体上,使每一个铂纳米粒子都处于气体多孔电极的三相界面上,有效地调控铂纳米粒子的尺寸和分散度. 单电池测试表明,以铂载量为0.014 mgPt•cm^-2的IEE电极组装的电池的输出功率与铂载量为0.3 mgPt•cm-²的Nafion粘接Pt/C电极相当.     

基于铂微粒和Nafion膜修饰玻碳电极的甲醛传感器

通过在Nafion膜修饰玻碳电极表面电沉积铂微粒制备了甲醛电化学传感器(Pt/Nafion/GCE)。利用循环伏安法研究了甲醛在该传感器上的电化学行为,优化了实验参数,在此基础上建立了用伏安法直接测定甲醛的新方法。在酸性溶液中,甲醛的氧化峰电流与其浓度在1.0×10-6~1.0×10-3mol/L的范围内呈良好的线性关系(r=0.9995),检出限为5.0×10-7mol/L。本文所提出的测定甲醛的方法具有较高的灵敏度和较好的重现性。     

纳米铂直接修饰玻碳电极的制备及在半胱氨酸中的电化学行为

采用一步化学原位还原法将球形纳米铂颗粒直接修饰在玻碳电极上,用SEM、EDS和电化学方法对该电极进行表征并与铂片电极、裸玻碳电极进行了对比。结果表明,纳米铂修饰电极的峰电流与扫描速度呈线性关系,纳米铂在电极表面覆盖率为1.28×10-7mol/cm2。循环伏安法研究结果表明纳米铂修饰电极对半胱氨酸的催化氧化作用和铂片电极相比提高了数倍,且峰电位负移了0.3V。在纳米铂修饰的玻碳电极上,半胱氨酸的浓度在1.0×10-7mol/L到1.0×10-5mol/L范围内和催化电流呈线性关系。     

碳材料中多层次孔对负载铂电催化活性的影响

分别以商用碳黑XC-72、介孔碳CMK-5和含多层次孔的碳气凝胶HCA为载体, 微波法负载Pt纳米粒子, 在硫酸和甲醇溶液中进行循环伏安测试, 考察碳材料中多层次孔对其电催化活性的影响. 结果显示, Pt/HCA电极表现出较高的峰电流(7.5 mA·cm-2)和电化学活性面积(128.0 m2·g-1). 这可能是因为碳气凝胶具有连续但非周期性的介孔结构, 有利于Pt纳米粒子的分散以及反应物质的传质.     

以多聚甲醛为还原剂制备新型阳极Pt/CMK-3催化剂

 以多聚甲醛为还原剂,采用液相还原法制备了Pt/CMK-3直接甲醇燃料电池(DMFC)阳极催化剂,并采用透射电镜和X射线衍射技术对其进行了表征. 结果表明,有序介孔碳CMK-3具有规整的二维有序孔道结构,为DMFC中电子和燃料的传输提供了方便的路径,同时它较大的比表面积使得Pt纳米粒子很好地分散在其表面; Pt/CMK-3催化剂中Pt粒子的平均粒径为2.8 nm, 小于E-TEK公司的商品化Pt/XC-72和以甲醇为还原剂制备的Pt/C-M催化剂,并且粒径分布范围窄,结晶度低. 察了Pt/CMK-3催化剂对甲醇的电催化氧化性能,发现Pt/CMK-3催化剂对甲醇氧化的电催化性能优于Pt/XC-72和Pt/C-M催化剂.     

铂/聚邻甲基苯胺/碳材料掺杂碳糊电极对甲醇的催化氧化

以石墨和液体石蜡油为主要原料,分别制备了掺杂不同量多壁碳纳米管(MWCNT)、石墨烯(GRA)、电容活性炭(YEC)和电池活性炭(YBC)的多种碳糊底电极Y-CPE(Y代表各种掺杂碳材料,CPE代表纯碳糊电极).采用恒电位法在-0.10 V(vs.Ag/Ag Cl)电位下将铂电沉积到这些电极上.结果表明,当电池碳的含量为14%时,Pt/YBC-CPE(14%)复合电极对甲醇具有最好的电催化氧化活性.采用恒电位方法在0.85 V(vs.Ag/Ag Cl)电位下将聚邻甲基苯胺(POT)电聚合沉积到纯碳糊电极CPE和含有电池碳的YBC-CPE(14%)电极上,得到复合电极POT/CPE和POT/YBC-CPE(14%),再通过恒电位方法将铂电沉积到这2个复合电极上.扫描电镜(SEM)观察结果表明,在Pt/CPE,Pt/YBC-CPE(14%),Pt/POT(6.5 mC)/CPE和Pt/POT(6.5 mC)/YBC-CPE(14%)4个复合电极中,在Pt/POT/YBC-CPE(14%)复合电极上的铂粒子的尺寸最小,并且Pt/POT(6.5 mC)/YBC-CPE(14%)复合电极电催化氧化甲醇活性最高.在POT(6.5 mC)/CPE和POT(6.5 mC)/YBC-CPE(14%)上Pt纳米颗粒的电沉积过程是一个近似的3D成核过程.研究还发现,复合电极Pt/POT/CPE和Pt/POT/YBC-CPE电催化氧化甲醇的活性随POT膜厚度的增加先增大后减少,存在一个最佳的膜厚度.     

Enhanced Electrocatalytic Activity of Dual Template Based Pt/Cu‐zeolite A/Graphene for Methanol Electrooxidation

A novel Pt/Cu‐zeolite A/graphene based electrocatalyst was successfully prepared by chemical reduction method for methanol electrooxidation. Graphite oxide and Cu functionalized zeolite A were simultaneously reduced by NaBH₄ to prepare Cu‐zeolite A/graphene support which was used to deposit Pt nanoparticles. The nanostructure and composition of as‐prepared Pt/Cu‐zeolite A/graphene composites were characterized by X‐ray diffractometer, X‐ray fluorescence, Fourier transform infrared spectrometer and scanning electron microscopy. The electrocatalytic properties of Pt/Cu‐zeolite A/graphene modified electrode for methanol oxidation were investigated by cyclic voltammetry and chronoamperometry in 0.10 mol/L H₂SO₄ + 0.50 mol/L CH₃OH solution. Compared with Pt/zeolite A/graphene electrode and Pt/graphene electrode, Pt/Cu‐zeolite A/graphene based electrode exhibited obviously enhanced current and higher electrocatalytic activity for methanol electrooxidation. The increased electrocatalytic activity was attributed to the presence of zeolite A and reduced graphene oxide based dual template, which significantly increased the effective electrode surface and facilitated the diffusion of analytes into the electroactive catalyst.     

High dispersion and electrocatalytic properties of platinum nanoparticles on graphitic carbon nanofibers (GCNFs)

Highly dispersed platinum nanoparticles were electrodeposited on graphitic carbon nanofibers (GCNFs) by cyclic voltammetry (CV) in 7.7 mM H2PtCl6+0.5 M HCl aqueous solutions. The graphitic carbon nanofibers (GCNFs) used in this paper were grown directly on a graphite disk by chemical vapor deposition (CVD). The micrographs and element composition of Pt/GCNFs/graphite electrode were characterized by scanning electron microscopy (SEM) and electron diffraction spectroscopy (EDS). The electrocatalytic properties of Pt/GCNFs/graphite electrode for methanol oxidation have been investigated by CV and excellent electrocatalytic activity can be observed even at very low platinum loading (md=8.79 microg cm(-2)). The highest mass activity (MA) for methanol oxidation reaches 323 Ag(-1) when Pt/GCNFs/graphite electrode was cycled at a sweep rate of 50 mVs(-1) by CV in 2 M CH3OH+1 M H2SO4 aqueous solutions. This may be attributed to the small particle size and high dispersion of platinum particles coated on GCNFs and shows good potential application in direct methanol fuel cell (DMFC). Additionally, the long-term cycling stability of platinum catalysts was also investigated.     

Influence of Hierarchical Porosity in Carbon Material on Electrocatalytic Property of Supported Pt Nanoparticles

The influence of hierarchical porosity on electrocatalytic property was investigated with Pt nanoparticles supported on three types of carbon materials, namely, commercial Vulcan XC-72, ordered mesoporous carbon CMK-5, and hierarchical carbon aerogel (HCA). The electrocatalytic activity of carbon supported Pt nanoparticles was verified by cyclic voltammetry in H₂SO₄ and CH₃OH solution. Pt/HCA presented superior performance with higher peak current (7.5 mA·cm⁻²) and electrochemical active area (128.0 m²·g⁻¹). This could be attributed to the carbon aerogel with continuous but nonperiodical mesopore structure, which facilitated dispersion of Pt nanoparticles and mass transport around reactants and products.     

不同载体负载的铂催化剂在丙酮酸乙酯不对称氢化反应中的活性及其铂流失率比较

以介孔树脂材料FDU-14和介孔碳材料CMK-3为载体制备了两种负载型铂催化剂, 用N₂气吸附、X射线衍射及CO化学吸附等手段对这两种催化剂进行了表征, 并将这两种不同的负载型铂催化剂在丙酮酸乙酯不对称氢化反应中的催化性能及其铂流失率与商品化Pt/Al₂O₃催化剂进行了比较. 研究结果表明, 尽管Pt/Al₂O₃催化剂的初始活性和光学选择性均较高, 然而相同反应条件下乙酸溶剂中Pt/FDU-14和Pt/CMK-3催化剂的铂流失率比Pt/Al₂O₃催化剂的低. 通过对催化剂进行CO吸附原位傅里叶变换红外漫反射光谱(DRIFTS)表征, 从载体的不同表面电子性质角度解释了不同载体负载的铂催化剂在丙酮酸乙酯不对称氢化反应中的活性和铂流失率的差异.     

Effect of the iridium oxide thin film on the electrochemical activity of platinum nanoparticles

The influence of the iridium oxide thin film on the electrocatalytic properties of platinum nanoparticles was investigated using the electro-oxidation of methanol and CO as a probe. The presence of the IrO(2) thin film leads to the homogeneous dispersion of Pt nanoparticles. For comparison, polycrystalline platinum and Pt nanoparticles dispersed on a Ti substrate in the absence of an IrO(2) layer (Ti/Pt) were also investigated in this study. Inverted and enhanced CO bipolar peaks were observed using an in situ electrochemical Fourier transform infrared technique during the methanol oxidation on the Pt nanoparticles dispersed on a Ti substrate. Electrochemical impedance studies showed that the charge transfer resistance was significantly lower for the Ti/IrO(2)/Pt electrode compared with that of the massive Pt and Ti/Pt nanoparticles. The presence of the IrO(2) thin film not only greatly increases the active surface area but also promotes CO oxidation at a much lower electrode potential, thus, significantly enhancing the electrocatalytic activity of Pt nanoparticles toward methanol electro-oxidation.     

介孔碳负载铂催化剂的分散性和电催化活性

以介孔硅SBA-15为模板, 糠醇为碳源制备了高度有序的介孔碳(CMK-5), 并用微波法合成碳负载的铂纳米粒子的催化剂. 为改善铂微粒的分散性能, 在微波碳载过程中添加了适量的阳离子表面活性剂(CTAB). XRD和TEM测试结果表明, CTAB的加入改善了铂催化剂的分散性, 且使铂微粒的平均粒径降至2.9 nm左右. 循环伏安测试结果显示, 加入CTAB后所得Pt/CMK-5催化剂的电化学活性面积大于未加CTAB的以及商业Johnson Matthey公司的Pt/C催化剂的活性面积.     

A Highly Efficient,Clean‐Surface,Porous Platinum Electrocatalyst and the Inhibition Effect of Surfactants on Catalytic Activity

Herein we report a gentle seedless and surfactant‐free method for the preparation of clean‐surface porous platinum nanoparticles. In terms of electrocatalytic CH₃OH oxidation, the clean‐surface porous platinum exhibited better performance than platinum nanoparticles and a commercial Pt/C catalyst. The porous nanostructures exhibited 2.26‐fold higher mass activity and 2.8‐fold greater specific activity than the Pt/C catalyst. More importantly, three typical surfactants, cetyltrimethylammonium bromide/chloride (CTAB/C), poly(vinylpyrrolidone), and sodium dodecyl sulfate, were chosen to study the inhibition effect of surfactants on electrocatalytic performance. It was observed that the surfactants led to a clear selective decrease in electrocatalytic performance. CTAB/C inhibited the catalytic activity the most due to the stronger interaction between the OH‐enriched platinum surface and the positively charged molecules. Thus, this work indicates that these clean‐surface porous platinum nanoparticles may be used as efficient catalysts for direct methanol fuel cells and provides a greater understanding of the inhibition effects of surfactants on catalytic activity.