飞秒激光热反射实验系统测量金属薄膜中的超快速热传递过程

飞秒激光热反射技术已经成为研究不同材料中超快速热传导过程的有效实验方法.实验中采用前表面加热、后表面探测的方法对不同厚度的Au薄膜进行了测量,通过比较表面电子温度可以得到超快速激光加热条件下Au薄膜材料中电子温度振荡的传递速度.结果表明瞬态条件下非平衡态电子是热量的主要载体,根据实验测量值拟合得到的能量传递速度接近于非...     

飞秒激光热反射系统测量金属薄膜中的热波

金属材料中的热波现象可以利用包含电子弛豫时间影响的双曲两步模型进行理论分析.通过飞秒激光热反射实验系统对金属薄膜材料进行了测量.利用偏振分光棱镜将飞秒激光分成抽运光和探测光,其中较强的抽运光用于加热金属薄膜而较弱的探测光用于探测薄膜表面反射率随时间的变化,两束光之间的光程差通过步进电机进行精确控制.利用金属薄膜反射率和电子温度的正比例关系就可以得到电子温度随时间的变化规律.实验发现在加热激光脉冲过后的电子温度下降区间会出现另一个较弱的电子温度波峰,并利用相同厚度的两块金属薄膜样品重复测量对实验结果进行了验证.理论上这一现象可以解释为金属薄膜中热波在背面反射的结果,并且实验结果和双曲两步模型给出的热波理论计算结果相符合.根据实验结果计算出热波传递速度约为5×105m/s,对应的电子弛豫时间为60fs.     

飞秒脉冲激光作用下金属薄膜的热弹性研究

利用双曲-双温两步热传导和热电子崩力模型,考虑到晶格温度与应变速率的耦合效应,得到了用于描述飞秒激光作用下金属薄膜热力效应的超快热弹性模型。以飞秒脉冲激光辐照金属铜薄膜为例,运用具有人工粘性和自适应步长的有限差分算法,对不同能量密度和脉冲宽度条件下薄膜体内温度场和应力场的变化规律进行了数值模拟,对比分析了电子晶格耦合系数对超快加热过程的影响。结果表明,飞秒脉冲激光辐照早期为明显的非平衡加热过程,电子温度迅速升高,而晶格温度的升高却相对较慢;激光辐照早期的热力耦合效应导致薄膜前表面附近的热应力表现为压应力,随着时间的推移,热应力由压应力转变为张应力,为激光加工和激光对抗提供了理论参考。     

超快脉冲激光辐照金属薄膜热-力效应的模拟研究

基于双曲双温两步热传导和热电子崩力模型,考虑到超快脉冲激光辐照金属薄膜材料过程中的热-力耦合效应,得到了完全耦合的、非线性的超快热弹性模型.运用具有人工粘性和自适应步长的有限差分算法,以脉宽为100 fs的脉冲激光辐照200 nm厚金膜为例,对薄膜体内的电子-晶格温度及温度梯度、热应力和电子热流进行了数值模拟研究.结果表明：脉冲辐照早期为明显的非平衡加热阶段,同时形成较大的热电子崩力;电子热流出现双峰现象;超快加热引起的热应力是导致薄膜力学损伤的主要原因.     

多晶碲化锌薄膜载能子超快动力学实验研究

利用双波长飞秒激光抽运-探测实验方法测量了掺氮多晶ZnTe薄膜在飞秒激光加热情况下载能子超快动力学过程. 采用包含电子弛豫过程和晶格加热过程的理论模型拟合实验数据, 二者符合得很好. 拟合得到10 ps以内影响掺氮多晶ZnTe薄膜表面超快反射率变化的三个弛豫过程的时间常数均为亚皮秒量级. 其中, 正振幅电子弛豫过程是由电子-光子相互作用引起的载流子扩散和带间载流子冷却过程, 负振幅电子弛豫过程是由缺陷造成的光激载能子的俘获效应引起的, 晶格加热过程主要通过电子-声子耦合过程进行的.     

Co膜中多次超快瞬态反射突变现象研究

飞秒激光泵浦瞬态热反射技术是研究金属薄膜超快动力学的有效手段,这种技术具有两大突出特点：首先,可以揭示飞秒激光激发的微观电、声子的传输过程是一个非平衡热输运过程。其次,反射率瞬态变化实验中电子运动的超短时间分辨可以用来研究热过程中电子的非平衡相互作用情况。利用磁控溅射真空镀膜技术,在玻璃衬底和硅衬底上蒸镀了不同厚度的Co单层膜,Cr,Co双层膜以及Ag,Co双层膜。利用飞秒激光瞬态反射技术研究了Co膜及其双层膜的瞬态反射率响应。结果表明,在同一厚度的Co膜样品上,施加不同的泵浦光功率时,Co膜内电子的加热时间与泵浦光功率的大小无关,均为0.1344 ps。而对于不同厚度的Co膜,电子的热化时间与薄膜厚度直接相关。此外,发现与以往研究结果不同的是,在泵浦光功率足够大时,玻璃衬底上的Co膜在飞秒激光脉冲泵浦下会出现两次或三次瞬态反射率下降现象,Co膜厚度决定了Co膜内瞬态反射率突变的次数,即Co膜内电子的超快动力学变化次数。     

飞秒激光抽运探测热反射法对金属纳米薄膜超快非平衡传热的研究

随着微电子器件尺寸的减小、 工作频率的提高, 金属薄膜中电子与声子将处于非平衡状态, 这将导致微电子器件的热阻增大. 为准确地对这些微电子器件进行热管理, 电子-声子耦合系数的测量变得越来越重要. 本文采用飞秒激光抽运-探测热 反射法研究了不同厚度的金属纳米薄膜的非平衡传热过程. 通过抛物两步模型对实验数据进行拟合, 在拟合过程中引入电子温度与声子温度对反射率影响的比例关系, 从而优化了拟合结果. 通过对不同厚度的Ni膜与Al膜的电子-声子耦合系数的研究, 表明金属薄膜中的电子-声子耦合系数并不随薄膜厚度的改变发生变化. 实验结果还验证了探测光的反射率同时受到电子温度和声子温度的影响, 并通过数据分析量化了电子温度和声子温度对反射率的影响系数.     

Cu—Ba—O薄膜在超短激光脉冲作用下的光透射率特性

用泵浦－探测技术测量了金属－介质复合薄膜Ｃｕ－Ｂａ－Ｏ的光学透射率在超短激光脉冲作用下随延迟时间的瞬态变化曲线，获得了薄膜对光的透射率迅速减小并在皮秒时间内恢复原状的实验结果。该现象是由薄膜中金属超微粒子内费米能级附近电子被飞秒激光脉冲激发所产生的非平衡态电子经历瞬态弛豫造成的。本文从理论上给出了薄膜中Ｃｕ超微粒子的电子声子相互作用常数ｇ的修正数值。     

飞秒激光泵浦-探测热反射系统的建立与调试

建立了用来研究超快传热现象的飞秒激光泵浦-探测热反射系统.利用该系统测量并得到了在140fs(飞秒)超短脉冲激光加热下, 50 nm金膜的非平衡电子温升引起的反射信号随时间的变化曲线.由于加热光单脉冲能量密度只有5×10-3mJ/cm2,估算最高温升在10 K以内,这有效地减小了由丁物性参数随温度变化而引起的洪差.论文介绍了在系统的调试过程中,各种因素对实验结果的影响,并对实验结果及数据处理方法进行了讨论.     

铝纳米薄膜热导率的实验研究

金属纳米薄膜作为一种典型的纳米材料,已广泛应用于信息技术领域。研究表明,随着金属薄膜特征尺寸的减小,金属薄膜体现出与常规不同的热输运特性。本文采用飞秒激光泵浦-探测实验方法,结合抛物两步模型和修正的抛物两步模型,对铝纳米薄膜热导率进行研究。结果表明,考虑了声子热导率修正的抛物两步模型比抛物两步模型更能准确描述热反射信号。拟合得到铝膜热导率分别为98 W·m~(-1)·K~(-1)和94 W.m~(-1)·K~(-1),小于铝的体材料热导率,铝纳米薄膜热导率具有尺度效应,同时拟合得到声子热导率为2.8 W·m~(-1)·K~(-1),提出一种利用飞秒激光泵浦-探测测量声子热导率的方法。     

Convergence of electron kinetic,two-temperature,and one-temperature models for laser short-pulse heating

The laser short-pulse heating of metallic workpieces initiates the non-equilibrium heating in the surface vicinity of the substrate. The material response to the non-equilibrium heating cannot be predicted accurately by the one-temperature model. Consequently, new models pertinent to laser short-pulse heating are needed. In the present study, laser short-pulse heating of gold, copper, and lead is considered. The material responses to the laser short-pulse due to the electron kinetic theory and the two-temperature and the one-temperature models are examined in detail. The differences between the collisional and diffusional heating mechanisms are presented. The conditions for the convergence of conduction mechanisms are discussed. The electron kinetic theory, the two-temperature, and the one-temperature predictions are compared for three substrates. It is found that the electron kinetic theory predictions differ from the predictions of the one-temperature model in the surface vicinity of the substrate during the early heating duration. As the heating progresses, both models predict similar temperature profiles. The electron kinetic theory and the two-temperature model predictions are in good agreement. PACS 44.10.+i; 42.62.-b     

Two-Temperature Modeling of the Anode Contraction Region of High-Intensity Arcs

In this paper, an analytical model for a two-temperature plasma (Te > Tg) is established which is suitable for dealing with arcflow interactions induced by the arc itself. This model is applied to the anode contraction region of high-intensity argon arcs taking the interaction of anode and cathode jets close to the anode into account. The complete set of conservation equations describing the mass, charge, momentum, and energy transport of a two-temperature plasma with temperature-dependent transport properties is solved numerically by an interative finite-difference method using appropriate boundary conditions. Results for an atmospheric-pressure argon arc indicate that the temperature discrepancy between electrons and heavy particles is very pronounced in the arc fringes and in the regions close to the anode, while the departure from kinetic equilibrium becomes insignificant in regions in which the temperature exceeds 12 000 K (i.e., in the arc core). The computed temperature fields of the heavy particles in the anode contraction region resemble the observed arc appearance which clearly shows the interaction of anode and cathode jets in front of the anode.     

An electrohydrodynamics model for non-equilibrium electron and phonon transport in metal films after ultra-short pulse laser heating

The electrons and phonons in metal films after ultra-short pulse laser heating are in highly non-equilibrium states not only between the electrons and the phonons but also within the electrons. An electrohydrodynamics model consisting of the balance equations of electron density, energy density of electrons, and energy density of phonons is derived from the coupled non-equilibrium electron and phonon Boltzmann transport equations to study the nonlinear thermal transport by considering the electron density fluctuation and the transient electric current in metal films, after ultra-short pulse laser heating. The temperature evolution is calculated by the coupled electron and phonon Boltzmann transport equations, the electrohydrodynamics model derived in this work, and the two-temperature model. Different laser pulse durations, film thicknesses, and laser fluences are considered. We find that the two-temperature model overestimates the electron temperature at the front surface of the film and underestimates the damage threshold when the nonlinear thermal transport of electrons is important. The electrohydrodynamics model proposed in this work could be a more accurate prediction tool to study the non-equilibrium electron and phonon transport process than the two-temperature model and it is much easier to be solved than the Boltzmann transport equations.     

光学性质对超快激光辐照下铜膜热响应的影响

在超快激光照射过程中,金属靶材的光学性质是动态变化的。采用双温模型与分子动力学结合法,考虑动态和常数光学性质两种情况,对不同脉宽的超快激光照射下铜薄膜的热响应进行了模拟研究。其中,常数光学性质包括由激光沉积能量相等计算得到的等效平均反射率和室温下的吸收系数。结果表明:两种情况下的电子温度和晶格温度均差别较小,尤其是脉宽远小于电子-晶格弛豫时间的飞秒激光; 而当激光脉宽相当于或大于电子-晶格弛豫时间时,如皮秒激光,光学性质的动态变化对材料的熔化和重凝的影响则比较明显。     

Emission enhancement ratio of the metal irradiated by femtosecond double-pulse laser

A numerical solution of the two-temperature model has been performed up to the double-pulse femtosecond laser heated metal target. The two-temperature model is used to analyze the double-pulse laser with the following major conclusions. We confirm the distinctly different results on the single pulse and double pulse. The double-pulse laser heated lattice temperature is higher than the single pulse. Through the Boltzmann equation, we estimate the variation of the emission enhancement. At the same time, this experimental result is qualitatively similar to the theoretical result.     

A two-temperature model of optical excitation of acoustic waves in conductors

A two-temperature model of optical excitation of acoustic pulses in conductors has been developed. According to this model, the energy of light at first is absorbed by free carriers and only then is the optical pulse energy transferred to long-wavelength phonons of the conductor lattice. It is shown that the shape of the acoustic pulse excited by a laser in conductors can be presented as a convolution of the laser pulse envelope and the transfer function. An analytical dependence of the transfer function on time is derived.     

Effect of Pulse Width and Fluence of Femtosecond Laser on Electron--Phonon Relaxation Time

The electron phonon relaxation time as functions of pulse width and fluence of femtosecond laser is studied based on the two-temperature model. The two-temperature model is solved using a finite difference method for copper target. The temperature distribution of the electron and the lattice along with space and time for a certain laser fluence is presented. The time-dependence of lattice and electron temperature of the surface for different pulse width and different laser fluence are also performed, respectively. Moreover, the variation of heat-affected zone per pulse with laser Auence is obtained. The satisfactory agreement between our numerical results and experimental data indicates that the electron-phonon relaxation time is reasonably accurate with the influences of pulse width and Auence of femtosecond laser.     

Heating and cooling of the multiply charged ion nonequilibrium plasma in a high-current extended low-inductance discharge

Using a radiation magnetohydrodynamics two-temperature model (RMHD model) of a high-current volumetric radiating Z-discharge, the heating and cooling of the nitrogen plasma in a pulsed pinched extended discharge is investigated as applied to the problem of creating a recombination laser based on 3 → 2 transitions of hydrogen-like nitrogen ions (λ = 13.4 nm). It is shown that the power supply of the discharge, which is represented by a dual storage-forming line and a transmission line, makes it possible to raise the power density of the nitrogen plasma to 0.01–1.00 TW/cm³. Accordingly, there arises the possibility of generating a fully ionized (i.e., consisting of bare nuclei and electrons) plasma through the heating (compression) of electrons owing to the self-magnetic field of the plasma current and Joule heat even if the plasma is cooled by its own radiation at this stage. Such a plasma is needed to produce the lasing (active) medium of a recombination laser based on electron transitions in hydrogen-like ions. At the second stage, it is necessary to rapidly and deeply cool the plasma to 20–40 eV for 1–2 ns. Cooling of the fully ionized expanding plasma was numerically simulated with the discharge current switched on and off by means of a switch with a rapidly rising resistance. In both cases, the plasma expansion in the discharge is not adiabatic. Even after the discharge current is fairly rapidly switched off, heating of electrons continues inside the plasma column for a time longer than the switching time. Discharge current switchoff improves the electron cooling efficiency only slightly. Under such conditions, the plasma cools down to 50–60 eV in the former case and to 46–54 eV in the latter case for 2–3 ns.     

Effect of pressure relaxation during the laser heating and electron–ion relaxation stages

The multi-phase equation of state by Bushman et al. (Sov. Tech. Rev. 5:1–44, 2008) is modified to describe states with different electron and ion temperatures and it is applied to the non-equilibrium evolution of an aluminum sample heated by a subpicosecond laser pulse. The sample evolution is described by the two-temperature model for the electron and ion temperatures, while the pressure and density are described by a simplified relaxation equation. The pressure relaxation in the heating stage reduces the binding energy and facilitates the electron-driven ablation. The model is applied to estimate the ablation depth of an Al target irradiated by a subpicosecond laser pulse. It improves the agreement with the experimental data and provides a new explanation of the ablation process.     

Theory of passive mode locking of solid-state lasers using metal nanocomposites as slow saturable absorbers

Mode locking of solid-state lasers using metal nanocomposites as slow saturable absorbers (SAs) is studied theoretically. The derived equation for the transient nonlinear response of metal nanocomposites is based on the semiclassical two-temperature model. The model is confirmed experimentally by pump-probe measurements on Au nanoparticles (NPs). The theory was applied to study passive mode locking of a solid-state laser containing Au NPs as SA in the green spectral range. Pulse durations as short as 100 fs are predicted, and design criteria of metal NP SAs are derived.