含膦酰杂菲侧基聚乙炔的合成与热稳定性

以2-(6-氧化-6-氢-二苯基(c,e)<1,2>氧杂磷酰基)-1,4-二羟基苯(ODOPB)结构单元为中心,在两侧通过酯化反应分别引入4-乙炔基苯甲酰基和4-烷氧基苯甲酰基,并作为乙炔单体,在[Rh(nbd)Cl]2催化下,30℃聚合得到了含磷酰杂菲(DOPO)基团的聚乙炔.1H-NMR和GPC分析表明,由于DOPO存在较大π共轭结构和较强极性效应,在诱导聚乙炔主链采取高反式构型的同时,增加了分子链内相邻侧基之间的相互作用,使整个分子链趋向二维共平面结构,有利于增强分子链之间的相互作用.TGA显示,与不含磷酰杂菲侧基的模型聚乙炔相比,DOPO的引入使聚乙炔呈现良好的热稳定性,起始热分解温度(T5%)接近400℃,说明通过增强分子链内侧基间相互作用有助于提高热稳定性.     

以膦酰杂菲为侧基的1-戊炔聚合反应及其结构与热力学性质

以2-(6-氧化-6-氢-二苯基(c,e)<1,2>氧杂膦酰基)-1,4-二羟基苯(ODOPB)结构单元为中心,在两侧通过酯化反应分别引入4-(4-戊炔氧基)苯甲酰基和4-丁氧基苯甲酰基,得到了1-戊炔衍生物单体M-34,同时合成了不含9,10-二氢-9-氧杂-10-膦杂菲-10-氧化物(简称膦酰杂菲,DOPO)基元的M-34模型化合物M-0.分别以[Rh(nbd)Cl]2和Rh(nbd)B(C6H5)4为催化剂,研究了催化剂浓度和聚合时间对M-34和M-0聚合反应收率的影响.结果表明,由于DOPO存在较大π共轭结构和较强极性效应,降低了催化剂的活性,使得聚合产物P-34分子量较低,但改善了P-34的溶解性,并诱导P-34主链基本采取全反式构型,从而有利于增强侧基之间的相互作用,使这种含有DOPO的聚1-戊炔衍生物呈现良好的热稳定性,且优于其不含DOPO模型聚合物P-0的热稳定性.但同时DOPO的引入也增加侧基的体积,为链段运动提供了较大的自由体积,使得P-34的Tg低于不含DOPO模型聚合物P-0的Tg.     

含磷酰杂菲侧基聚苯乙烯的合成及其荧光性质

以2-(6-氧化-6-氢-二苯基(c,e)1,2氧杂磷酰基)-1,4-二羟基苯(ODOPB)结构单元为中心,在两侧通过酯化反应分别引入4-乙烯基苯甲酰基和4-戊氧基苯甲酰基,并作为苯乙烯衍生物单体(MED),在AIBN引发下,聚合得到了含9,10-二氢-9-氧杂-10-磷酰杂菲-10-氧化物(简称磷酰杂菲,DOPO)基团的聚苯乙烯衍生物(PED).因侧链之间具有较强的相互作用以及聚苯乙烯主链的刚性而易形成聚集形态,使分子量超出GPC的正常检测范围;同时表现出良好的热稳定性,MED和PED失重5%时的对应温度分别为339℃和345℃.也正是这两种作用同时存在,并相互制约,侧基之间产生了一定程度的规整排列,限制了磷酰杂菲基团的转动,降低了其非辐射能量转移,从而相对于MED,使PED在THF溶液中荧光强度得到了明显增强.由于PED在沉淀聚集过程中受到THF和沉淀剂(水或正己烷)的共同影响,在沉淀剂含量达到70%之前,侧基之间难以形成规整排列,其分子链内转动很大程度引起非辐射能量转移,所以随着沉淀剂含量的增加,荧光强度不断降低;然而当沉淀剂含量达到70%以上时,由于水分子能够与两个相互靠近的侧基共同形成基于氢键作用的复合超分子结构,这不仅抑制了磷酰杂菲基团的转动能力,增强了荧光强度,在一定程度上表现出AIEE特性,而且会在450nm处出现新的肩峰,以显示该结构有别于侧基自身的密聚集;但以正己烷为沉淀剂时,因不能形成氢键超分子结构,PED分子链只是无序密聚集,所以表现为只是随着正己烷加入荧光强度不断降低,没有出现荧光红移的现象。     

含磺化芴基侧基的聚芳醚氧膦质子交换膜的合成与表征

将9,9-二(4-羟苯基)芴(BHPF)与二(4-氟苯基)苯基氧膦(BFPPO)聚合,合成了含芴基侧基的聚芳醚氧膦(PAEPO),并采用后磺化法,制备了侧链型磺化聚芳醚氧膦(sPAEPO)质子交换膜.通过核磁与红外确定了聚合物的化学结构,用原子力显微镜对sPAEPO的微观结构进行了表征,同时对sPAEPO质子交换膜的尺...     

聚膦腈-g-聚己内酯共聚物的合成与表征

通过三甲基碘硅烷与聚二(2-甲氧基乙氧基)膦腈侧链上的醚键反应后水解得到侧链含部分羟基的聚膦腈,然后利用聚膦腈的侧链羟基在异辛酸亚锡催化作用下,引发己内酯单体开环聚合制备了聚膦腈-g-聚己内酯共聚物.该共聚物中聚己内酯链段的接枝率和侧链长度可通过改变三甲基碘硅烷和己内酯单体的投料来控制.     

含磷酰杂菲侧基的苯乙烯衍生物聚焦诱导发光特性及其在过渡金属子检测中的应用

以2-(6-氧化-6-氢-二苯基(c,e)<1,2>氧杂磷酰基)-1,4-二羟基苯(OOPB) 为中心结构单元,通过两步酯化反应,在两侧分别引入4-戊氧基苯甲酰基和4-乙烯基苯甲酰基,得到苯乙烯衍生物(ME).由于磷酰杂菲基团的大π共轭结构和极性共同作用,使得形成聚集体后分子内转动受到限制,降低了非辐射去活效率,使 ME在达到一定聚集程度时,荧光强度成倍增加,呈现出聚集诱导发光增强(AIEE) 特性. 同时,Pt2+,Ru3+,Fe3+的加入对ME有显著的猝灭效果;而 Fe2+ 只是在形成聚集体过程中才有猝灭效果.     

含三苯基氧膦基团的磺化聚苯并咪唑质子交换膜

通过酯化反应合成了3,3'-二磺酸钠-4,4'-二甲酸二甲酯基联苯和二(4-甲酸甲酯基苯基)苯基氧膦单体,并将其与3,3'-二氨基联苯胺共缩聚,制备了含三苯基氧膦基团的可溶性磺化聚苯并咪唑.三苯基氧膦基中的苯侧基促使高分子链排列疏松,产物溶解性提高;而氧膦基团增加了产物的吸水率,并显著提高了其电导率.     

1-取代苯磺酰基-3-(4′,6′-二取代均三氮苯-2′-基)-1,3,2-二氮磷杂环戊烷的合成及结构分析

本文研究了N-取代苯磺酰-N′-(4,6-二取代均三氮苯-2-)乙二胺与三(二烷胺基)膦的反应,发现了可一步得到关环的产物。从~1HNMR,~(13)CNMR谱观察到在室温下均三氮苯环的单键旋转阻滞现象,X衍射结果对此作了进一步讨论。磷杂环最稳定的构象为袋式,从键长以及环外氮原子杂化状态推测这类化合物在磷与环外氮原子之间有一定程度的dπ-pπ键。     

脂蛋白脂酶激活剂艾溴利平类似物的合成

合成了两个新型的艾溴利平类似物——N-2 -硝基-4-氯苯基-4-[(膦酸二乙酯基)甲基]苯甲酰肼(5,总收率28.1％)和N-2-四氮唑基-4-氯苯基-4-[(膦酸二乙酯基)甲基]苯甲酰胺(7,总收率30.5％).以对氯甲基苯甲酸为原料,经酯化、水解和酰氯反应制得中间体4-[(膦酸二乙酯基)甲基]苯甲酰氯(4);4与2-硝基-4-氯苯肼盐酸盐反应合成了5.4先与2-氨基-5-氯苯腈反应制得N-2-氰基-4-氯苯基-4-[(膦酸二乙酯基)甲基]苯甲酰胺(6);6再与叠氮化钠反应合成了7.其结构经1 H NMR和IR表征.     

一种新的侧链型液晶高分子的光谱研究

本工作使用FTIR、FT-RAMAN、~1H-NMR和~(13)C-NMR等方法,对一新型的侧链型液晶高分子聚-2,5-双(4-甲氧基苯甲酰氧基)苯乙烯的结构进行了表征,并对形成液晶态的分子间相互作用力作了讨论。实验结果表明,这种侧链型液晶高分子的相互作用主要发生在作为侧基的液晶基元之间。聚合物的核磁谱表现异常,其原固有待进一步研究。     

Polymer‐Decorated Carbon Nanotubes as Transducers for Label‐Free Photonic Biosensors

A biosensor taking advantage of the optical properties of sorted carbon nanotubes has been developed. A polyfluorene polymer bearing azido groups was synthesized and used for the selective extraction of semi‐conducting nanotubes from the bulk population. The resulting polymer‐decorated nanotubes were then conjugated by click‐chemistry to a ligand unit (biotin), and the sensing properties of the biotinylated nanotubes were investigated by photoluminescence measurements, upon interaction with the streptavidin target.     

Synthesis and optical and electrochemical properties of copolymers consisting of 9,9‐dihexylfluorene and aromatic triazole chromophores

Aromatic triazole chromophores were incorporated into polyfluorene in an attempt to increase electron affinity, to promote emission efficiency, and to diminish excimer formation. Poly(9,9‐dihexylfluorene) ( P1 ) and new copolymers with aromatic triazoles ( P2 – P4 ) were prepared by Suzuki coupling polymerization. In P2 , the aromatic triazole (3.8 mol %) was attached exclusively as terminal groups, whereas P3 and P4 were main‐chain copolymers containing 3.9 and 10.3 mol % aromatic triazole chromophores, respectively. The copolymers were soluble in common organic solvents and showed high decomposition temperatures (437–458 °C). The twisted structure between the triazole and fluorene increased the emission efficiency and effectively prevented excimer formation in P2 – P4 . After the introduction of the triazole units, the absorption spectra showed a blueshift (from 388 to 381 nm in chloroform) due to confined conjugation, but the photoluminescence spectra remained almost the same (417–418 nm); this was attributed to oligofluorene segments. No emission of triazole fluorophores was observed because of efficient energy transfer from the triazole to oligofluorene segments. However, incomplete energy transfer was observed in CH₃COOH. The optical stability upon thermal annealing was also improved by the incorporation of aromatic triazole segments. From cyclic voltammetry results, P2 – P4 , containing triazole groups, showed greater electron affinity (lowest unoccupied molecular orbital level = ?2.67 to ?2.71 eV) than P1 (?2.52 eV). Electroluminescence devices of P1 – P4 all exhibited excimer emissions (483–521 nm), which could also be diminished by the introduction of aromatic triazole chromophores. © 2006Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 136–146, 2007     

Molecularly imprinted polymeric film on semiconductor nanoparticles analyte detection by quantum dot photoluminescence

Incorporation of semiconductor nanoparticles into molecularly imprinted polymer provides a sensor material which can be easily shaped and with better selectivity because the bound template would quench the photoluminescence (PL) emission of quantum dots significantly. In this work, artificial receptors of various templates were synthesized with functional monomers such as methacrylic acid (MAA), semiconductor like CdSe/ZnS core-shell derivatized with 4-vinylpyridine and ethylene glycol dimethacrylic acid as the cross-linker. The quenching of photoluminescence emissions is presumably due to the fluorescence resonance energy transfer between quantum dots and template molecules. The photoluminescence emission is unaffected upon incubation of analyte with the blank control polymer.     

Phase behavior and anisotropic optical properties of photoluminescent polarizers

The phase behavior and anisotropic optical properties of tensile deformed blends of a photoluminescent polymer guest in an ultra‐high molecular weight polyethylene matrix were studied on the level of single molecules by means of scanning confocal optical microscopy. It is shown that upon tensile deformation of the blends, the system transforms from a phase‐separated system into a quasi‐molecular solid solution. The influence of this phase transition on the anisotropic optical properties of oriented blend films was also investigated with polarized steady‐state photoluminescence spectroscopy. We show that well‐dissolved guest molecules tend to reach higher degrees of orientation at lower draw ratios of the blend films compared to guests that phase‐separate from the matrix polymer. Dichroic ratios in emission in the range of 50 were observed in optimized blend films based on photoluminescent oligomers and linear low density polyethylene.     

Chimeric RNA Oligonucleotides with Triazole and Phosphate Linkages: Synthesis and RNA Interference

Chimeric RNA oligonucleotides with an artificial triazole linker were synthesized using solution‐phase click chemistry and solid‐phase automated synthesis. Scalable synthesis methods for jointing units for the chimeric structure have been developed, and after click‐coupling of the jointing units with triazole linkers, a series of chimeric oligonucleotides was prepared by utilizing the well‐established phosphoramidite method for the elongation. The series of chimeric 21‐mer oligonucleotides that possessed the triazole linker at different strands and positions allowed for a screening study of the RNA interference to clarify the preference of the triazole modifications in small‐interfering RNA molecules.     

Azide-alkyne click polymerization: An update

The great achievements of click chemistry have encouraged polymer scientists to use this reaction in their field.This review assembles an update of the advances of using azide-alkyne click polymerizati...     

Thermotropic and optical behaviour of new PDLC systems based on a polysulfone matrix and a cyanoazomethine liquid crystal

The thermotropic and optical characterisations of a novel polymer dispersed liquid crystal (PDLC) system based on polysulfone UDEL P-1700 as polymer matrix and a low molecular weight liquid crystal compound containing a mesogenic azomethine core and a cyano-substituent were investigated. The PDLC samples were prepared by solvent-induced phase separation (SIPS) and thermally induced phase separation (TIPS) methods using various compositions in the two components. Information on the morphology and phase structure was obtained by polarising optical microscopy, differential scanning calorimetry and X-ray diffraction measurements. PDLC systems with well-defined droplets were obtained for the composite with medium content of liquid crystal compound. The optical characterisation of these materials was performed by analysing their UV–visible absorption and photoluminescence emission as a function of the liquid crystal aggregation degree.     

Optical order of the polymer phase within polymer/fullerene blend films

This study reports on how the degree of polymer order within a polymer/fullerene blend can be investigated by spectroscopic methods. Non‐annealed blend compositions with 0–80 wt % fullerene content were analyzed using temperature dependent photoluminescence (PL) and room temperature spectroscopic ellipsometry (SE) measurements. To evaluate the SE data with respect to the optical order, an optical model was developed, including a lower and higher ordered polymer phase within a fullerene matrix. This was done using an effective medium approach describing the polymer by combining lower and higher ordered polymer properties (polymer‐EMA). The polymer/fullerene blend was then evaluated using another EMA consisting of the polymer‐EMA and the dielectric function of the disordered fullerene. The degree of optical order obtained by SE, was confirmed using another independent measurement, photoluminescence spectroscopy, according to the method of Francis C. Spano (2005). The volume fraction of the ordered polymer within the polymer‐EMA was found to be between 70 and 60 vol % for fullerene contents lower than 20 wt % in the polymer/fullerene blend. Above 20 wt % fullerene, the optical order of the polymer strongly decreases all the way down to 0 vol %. In contrast to the complementary performed X‐ray diffraction measurements, which address only the long‐range structural order of the blends, we give quantitative information on the optical order, including information on the composition, that is, volume fractions of the higher and lower ordered polymer. The gained information on the tilt of the polymer molecules with respect to the substrate is discussed comparing XRD results from the literature with those obtained by our SE model. Finally, the developed model is used to describe the influence of the P3HT molecular weight on the optical order. Results obtained with our model were compared to the structural data and mobility data in the literature. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Synthesis,photophysical, and electrochemical properties of triazolyl dendrimers with thiazolylchalcone surface unit

Synthesis of novel triazolyl dendrimers with thiazolylchalcone surface group and triazole as bridging unit has been achieved in good yields by click chemistry through convergent approach. All the triazolyl dendrimers showed an absorption band between 293 and 336?nm and an emission band between 430 and 435?nm. The intensity of absorption and emission bands increases on increasing the number of dendritic wedges and triazole units. Triazolyl dendrimers exhibited quasi-reversible behavior in cyclic voltammetry. A shift in the reversible potential was observed in cyclic voltammetry on increasing the dendritic wedges in the triazolyl dendrimers.