火试金减杂-电感耦合等离子体原子发射光谱法（ICP-AES）法测定高冰镍的金、银、铂、钯含量

建立了火试金减杂-电感耦合等离子体原子发射光谱法（ICP-AES）测定高冰镍中金、银、铂、钯含量的分析方法。实验采用火试金富集、熔融、灰吹得到合粒,通过减杂法得到银含量,通过ICP-AES法测定得到金、铂、钯含量。金、银、铂、钯的加标回收率在99.53%-101.83%之间,相对标准偏差小于3%。此方法快速、简洁,准确度高、精密度好,能够满足高冰镍的测定需求。     

Lifetimes and oscillator strengths of singly ionized vanadium

Lifetimes of 12VII levels have been measured by using the technique of laser-excited fluorescence from sputtered metal vapour. The uncertainty is between 7–9%. For a determination of the individual transition probabilities the corresponding emission branching ratios have been measured on a high-current hollow-cathode in conjunction with a 1 m Fourier-transform spectrometer. Thef-values of 86 VII lines, which cover a spectral range 260–420 nm, have an uncertainty of about 12%. Comparison is made with literature data.     

Application of a demountable water-cooled hollow-cathode lamp to atomic-fluorescence spectrometry

A demountable water-cooled hollow-cathode lamp has been investigated as a primary source in atomic fluorescence spectrometry. The discharge current ranged from 300 to 500 mA, and the flowing argon pressure between 0.4 and 4 mbar. Sensitivities ranging from 0.03 to 2 mug ml were obtained for 12 elements. The performances of the hollow-cathode lamp and those of the customary metal vapour discharge lamps for thallium, indium and gallium are compared. The role of the narrowness of the exciting lines in increasing the signal-to-scattering ratios is stressed.     

电感耦合等离子体发射光谱法测定锌精矿中的铟

应用电感耦合等离子体发射光谱法测定锌精矿中的铟,确定了最佳工作条件,选择了最佳分析谱线,并利用标准加入法和基体匹配法验证了方法的准确性。样品用氟化氢铵、盐酸、硝酸、高氯酸溶样,用盐酸定容。结果表明,电感耦合等离子体发射光谱法与萃取分离盐酸羟胺示波极谱法测定的铟含量结果一致。方法准确,快速,加标回收率为99.6%～101.7%,相对标准偏差为0.97%～2.1%。     

Determination of palladium, platinum and gold by first derivative spectrophotometry

Summary The application of first-derivative spectrometry to the simultaneous determination of palladium(II), platinum(IV) and gold(III) is described. Light absorption of stable chlorocomplexes formed in 1 mol/l hydrochloric acid provides the basis of their determinations. A difference in the derivative amplitudes between two first-derivative zero crossing points of one metal A is read, corrected for the contribution of metal B and used for quantitation of metal C. Palladium (0.48–20 g ml^–1), platinum (0.16–24 g ml^–1) and gold (0.32–24 g ml^–1) have been determined with good precision and accuracy without any separations. Results are also presented for the simultaneous determination of the three precious metals in the presence of several major constituents.     

Determination of traces of gold by hollow-cathode emission

The utility of a commercially available demountable hollow-cathode tube for emission spectrometric trace element analysis of solutions is demonstrated. The effects of cathode material, clean-up procedure, filler gas, and tube current were investigated to determine the conditions resulting in a satisfactory compromise between sensitivity and stability. Solutions of gold as myochrysine and as the metal dissolved in aqua regia were analyzed to show application of the commercial tube.     

An isocratic fluorescence HPLC assay for the monitoring of l-asparaginase activity and l-asparagine depletion in children receiving E. colil-asparaginase for the treatment of acute lymphoblastic leukaemia

A novel assay for the determination of l-asparaginase activity in human plasma is described that is based on the HPLC quantitation of l-aspartic acid produced during enzyme incubation. Methods for monitoring l-asparagine depletion are also described. Chromatography of l-aspartic acid, l-asparagine and l-homoserine (the internal standard) involved derivatization with o-pthaldialdehyde, then separation from other amino acids on a Phenomenex Luna C(18) column using a 1 mL/min flow rate and a mobile phase consisting of di-potassium hydrogen orthophosphate propionate buffer, pH 6, with 10% methanol and 10% acetonitrile. Fluoresence detection was at excitation/emission wavelengths of 357/455 nm. Under these conditions l-aspartic acid, l-asparagine and l-homoserine had retention times of 3.5, 9.8 and 17.7 min, respectively. The l-asparaginase assay was linear from 0.1 to 10 U/mL activity and interday precision and accuracy were less than 13%. The limit of quantitation was approximately 0.03 U/mL. The assay utility was established in 12 children who received E. coli l-asparaginase as treatment for acute lymphoblastic leukaemia.     

碱性氯化法破氰-碲共沉淀富集-电感耦合等离子体原子发射光谱法测定氰化退镀液中金含量

采用碱性氯化法氧化分解样品中氰化物,碲共沉淀法分离富集破氰溶液中的金,建立了电感耦合等离子体原子发射光谱法(ICP-AES)测定退镀液中金的分析方法. 在碱性条件下,使用次氯酸钠氧化分解退镀液中的氰化物,使其转化为二氧化碳和氮气,使用亚硫酸钠溶液中和破氰溶液中的余氯,消除氧化物对氰化物测试包的影响,可以简便快速判断退镀溶液破氰效果. 在3.6 mol/L盐酸介质中,12.5 mL碲溶液(2.5 g/L)和11.0 mL氯化亚锡溶液(1 mol/L)可定量沉淀5~500 μg金,50倍量的杂质元素不干扰测定. 金的质量浓度在0.05~25.00 mg/L范围内与其发射强度呈线性,线性回归方程为y=46.487x+0.343,相关系数r大于0.999 9,检出限为0.004 4 mg/L. 对实际样品进行准确度考察,测定结果的相对标准偏差(RSD, n=7)低于1.0%,加标回收率为96.9%~103.1%,实际样品测定结果与火试金法的对照结果一致性好.     

乙酸除铋火试金法测定粗铋中的金银含量

建立了用乙酸分离粗铋中铋-火试金重量法测定粗铋中金和银含量的方法。首先把粗铋焙烧氧化,然后用乙酸溶解粗铋的氧化物,过滤除去铋,消除铋对火试金法的干扰,将沉淀物灰化后,配料、高温熔融,熔态的金属铅捕集试样中的贵金属形成铅扣,将铅扣灰吹,得到金银合粒,用硝酸溶解分离金,用重量法测定金含量。方法准确度高,精密度好,金的加标回收率为99.2%～101%,银的加标回收率为98.2%～99.7%。能很好地满足粗铋中金、银的测定。     

微波消解-ICP-OES法测定汽车涂料中8种重金属

建立微波消解-电感耦合等离子体发射光谱(ICP-OES)测定汽车涂料中Pb,Cr,Se,Ba,Sb,As,Cd,Hg含量的方法。以HNO_3-H_2O_2(体积比为4∶1)混合酸消解样品,各元素分析谱线:Pb 220.353 nm,Cr 267.716 nm,Se196.090 nm,Ba 233.527 nm,Sb 217.581 nm,As 189.042 nm,Cd 228.802 nm,Hg 184.950 nm。8种元素测定结果的相对标准偏差为2.02%~12.94%(n=6);对白色、蓝色、红色汽车漆样品进行加标回收试验,Pb,Cr,Se,Ba,As,Cd,Hg,的加标回收率为81.26%~99.79%,Sb的回收率为62.43%~87.61%。该方法快速、简便,精密度、准确度较高,可用于汽车涂料中重金属含量的监控。     

Optimization of the operating conditions using factorial designs for determination of uranium by inductively coupled plasma optical emission spectrometry

A critical evaluation of the determination of uranium by inductively coupled plasma optical emission spectrometry was performed using factorial designs (2³) involving the factors: acid concentration, radio frequency power and nebulizer gas flow rate. All of the experiments in this study were made for five emission lines, in the presence of nitric and hydrochloric acid. The results demonstrated that, between nitric and hydrochloric acid, the determinations in the presence of nitric acid were most sensitive. The factorial design showed that the nebulizer gas flow rate was the most significant among the factors studied for the five emission lines. Calcium in concentrations of 10 mg L⁻¹ was observed to cause suppression of the emission intensity for some lines. Iron (at least up to 10 mg L⁻¹) did not interfere in the emission intensity of uranium across the five lines studied. Another experiment evaluated simultaneously the effect of 13 other elements, and the results demonstrated that these elements did not affect the emission intensity of uranium for the lines chosen. The optimized method, using the line at 385.957 nm, allows the determination of uranium with limit of quantification of 31 μg L⁻¹ and precision expressed as RSD lower than 2.2% for uranium concentrations of either 500 or 1000 μg L⁻¹. The accuracy was confirmed by analysis of two laboratory reference materials. The developed method was applied to the determination of uranium in an industrial effluent collected from uranium-producing mine in Caetite City, Brazil. The sample was analyzed by inductively coupled plasma mass spectrometry ICP-MS, and the observed recovery was satisfactory.     

Application of voltammetric methods for the analysis of gold and other transition metals in quartzite rock

Simple, rapid and accurate voltammetric methods viz. DCP, DPP and DPASV have been presented for the trace determination of gold and other transition metals in quartzite rock sample. The analysis has been performed using 0.1 M(NH4)2 tartrate, 0.1 M NaClO4 and 1 M NaOH as supporting electrolyte with 0.001% gelatin as maximum suppressor. The results show the presence of CuII(10.70), CoII(4.72), FeIII(66.96), AuIII(0.066), ZnII(1.68) and CdII(0.62) mg x g(-1) metal ions from the sample. Gold produced a well defined wave/peak with E1,2/Ep = -0.61 V/-0.64 V vs SCE, in 1 M NaOH supporting electrolyte. The quantitative analysis of metal inos was carried out by the method of standard addition. Statistical treatment of the observed voltammetric data reveals high accuracy and good precision of determination. The observed voltammetric results are comparable with those obtained using AAS method.     

Development and validation of a cost-effective,efficient, and robust liquid chromatographic method for the simultaneous determination of the acetyl and succinoyl content in hydroxypropyl methylcellulose acetate succinate polymer

A reversed-phase liquid chromatographic method was developed and validated for the determination of the content of free acetic acid, free succinic acid, acetyl substituents, and succinoyl substituents in hydroxypropyl methylcellulose acetate succinate (HPMCAS; Chemical Abstracts Service Registry No. 71138-97-1) polymer. This single new method gave accurate and precise measurement of both acetyl and succinoyl substituents, which had previously required 3 Japanese Pharmaceutical Excipients (JPE) methods to accomplish. Consequently, analysis time and turnaround time are decreased significantly. Furthermore, this method can also separate and determine the free acetic and succinic acids in HPMCAS polymer, a task that the corresponding JPE method cannot achieve. The values for accuracy (average recovery from 12 standard samples) were 99.9% for acetic acid and 99.8% for succinic acid. The values for injection precision (relative standard deviation [RSD]) were 0.11% for acetic acid and 0.28% for succinic acid. The values for intermediate precision (RSD) were 1.25% for determination of the acetyl content at the 8.78% (w/w) level and 1.33% for determination of the succinoyl content at the 10.9% (w/w) level. The values for intermediate precision (RSD) were 5.98% for determination of free acetic acid at the 0.12% (w/w) level and 5.13% for determination of free succinic acid at the 0.029% (w/w) level. The method was proven to be robust with respect to variation in the pH of the mobile phase, the concentration of potassium dihydrogen phosphate, and the flow rate. The method is well suited for quality control in today's fast-paced pharmaceutical laboratories.     

电荷注入检测器电感耦合等离子体光谱仪测定非金属元素的分析性能

研究了电荷注入检测器ICP光谱仪测定非金属元素的分析性能。以S、P、As、Se为代表的非金属元素在170－800nm波段内最灵敏的谱线均处于175－200nm远紫外区内。在此区内等离子体有很低的光谱背景发射和良好的谱线测量和背景测量的光度精度。标准曲线线性动态范围在4个数量级。给出了As,Se,S,P主要分析线的灵敏度、线背比、背景等效浓度及检出限。在纯水溶液中的检出限分别为：As 189.142nm 0.003mg/L,P213.618nm 0.005mg/L,S 180.731nm 0.01mg/L,Se 196.090nm 0.009mg/L.     

A capillary electrophoretic system based on a novel microemulsion for the analysis of coenzyme Q10 in human plasma by electrokinetic chromatography

A new analytical method for determination of coenzyme Q10 (2,3‐dimethoxy‐5‐methyl‐6‐decaprenyl‐1,4‐benzoquinone, CoQ10) in human plasma was developed based on CE using a double tensioactive microemulsion. CoQ10 was quantitatively extracted into 1‐propanol/hexane and quantified by MEEKC. The microemulsion was prepared by mixing 1.4% w/w sodium bis(2‐ethylhexyl) sulfosuccinate, 4% w/w cholic acid, 1% w/w octane, 8.5% w/w butanol, 0.1% w/w PVA and 85% w/w 10 mM Tris buffer at pH 9.0. The optimized electrophoretic conditions included the use of an uncoated silica capillary of 60 cm total length and 75 μm id, an applied voltage of 20 kV, room temperature and 214 nm ultraviolet detection. Selectivity, linearity, LOD, LOQ, precision and accuracy were evaluated as the parameters of validation. Owing to its simplicity and reliability, the proposed method can be an advantageous alternative to the traditional methodology for the quantitation of CoQ10 in human plasma with good accuracy and precision.     

辉光放电光谱法定量分析金属材料表面纳米级薄膜的研究

介绍了利用辉光放电光谱法分析金属材料表面的纳米级薄膜。通过优化辉光光源的放电参数，计算标准样品的溅射率。溅射率经校正后，建立各元素的标准工作曲线，从而形成了纳米级薄膜的定量表面分析方法。试验证明，此方法对膜厚的测定具有很好的准确度和精密度，可应用于多种金属材料表面纳米级薄膜的研究。     

电感耦合等离子体原子发射光谱(ICP-AES)法测定硫化物矿石中的铜铅锌

建立了电感耦合等离子体原子发射光谱(ICP-AES)法同时测定硫化物矿石中Cu、Pb、Zn三种元素的方法,取代了传统的四酸(HCl+HNO3+HClO4+HF)溶样法,采用简单的盐酸和硝酸溶解矿石,大大缩短了分析时间。选择干扰少且灵敏度高的谱线作为待测元素的分析谱线,采用左右两点扣背景的方法校正光谱干扰和基体匹配方法消除物理干扰,用GBW07162和GBW07163等不同种类的国家一级标准物质进行精密度和准确度实验,测定结果的相对标准偏差都在10%以内,测定结果都在标准值的误差范围内,符合地质矿产开发的要求。     

The determination of boron in solution to sub-p.p.b. concentrations by hollow-cathode emission

The determination of boron in solutions to sub-p.p.b. concentrations by hollow-cathode emission is demonstrated. The effects of cathode material, clean-up procedure, fill gas, and tube current were investigated to determine the conditions yielding optimal sensitivity. The boron atomic line emission is 200 times as intense as boron oxide band emission.     

Simultaneous determination of some trace metals in plant materials by energy-dispersive X-ray fluorescence method

Energy dispersive X-ray fluorescence method with chemical preconcentration has been worked out for Mn, Fe, Ni, Cu and Zn determination in plant materials. The analytical procedure involves wet digestion of organic matter, precipitation of metal ions with NaDDTC and the measurement of K emission lines of the elements to be determined. The overall precision of the method ranges from 3 to 7% /one relative S.D./ depending on the element.     

Precise and accurate determination of halogens in organic compounds using an amalgamated gold electrode

Precise and accurate titration of halogens in organic and inorganic materials has been studied. The halogen was titrated with coulometrically generated silver and determined potentiometrically by using an amalgamated gold indicator electrode. An argentometric titration curve using the amalgamated gold indicator electrode showed a large jump in potential at the endpoint as well as in mercurometric determination. Sodium carboxymethyl cellulose (CMC) and aluminum nitrate were added as they are most effective for clarifying the sample solution and eliminating adsorption of the halide ion on the silver halide generated. The electrolytes used were 0.5 M nitric acid containing 0.1% CMC and 0.2 M aluminum nitrate. Approximately 0.2 mmol of chloride, bromide, and iodide ions were titrated with high precision and accuracy. Their standard deviations were 0.03, 0.02, and 0.02%, respectively, with no apparent systematic error. The precise determination of halogens, employing oxygen flask combustion and dissolution of the halide salts in the electrolyte, was carried out with ±0.1% absolute error using samples weighing between 20 and 30 mg.