锂离子电池正极材料LiNi0.8Co0.2O2和LiNi0.95Ce0.05O2制备工艺优化

通过L9(34)拉丁正交实验, 利用极差分析法对制备LiNi0.8Co0.2O2的反应条件进行优化, 找出了合成LiNi0.8Co0.2O2的最佳工艺, 固相分段法制备LiNi0.8Co0.2O2的过程中, 反应物摩尔比、氧气压力、恒温时间及最终合成温度依次为主要影响因素.尝试把氧气压力作为独立因素进行考察, 进一步优化了合成工艺. 采用同样方法尝试研究了添加Ce合成了电化学活性较高LiNi0.95Ce0.05O2派生物正极材料. 实验电池电化学测试表明LiNi0.8Co0.2O2和LiNi0.95Ce0.05O2初始放电比容量分别为165, 148 mAh·g-1, 放电平台均在9 h以上.     

LiNi_(0.8)Co_(0.2)O_2的络合法合成及其电化学性能研究

采用络合法制备了锂离子电池的活性正极材料LiNi0.8Co0.2O2粉体,该合成材料结晶良好,层状结构发育完善.电池充放电测试表明,作为锂离子电池正极,其电化学性能与LiNi0.8Co0.2O2粉体的合成温度有关,其中以900℃下合成得到的材料性能最优:第1次放电比容量高达142mAh/g,循环30次后可逆比容量仍高达122mAh/g,容量损失为14.5%.文中对容量退化的原因进行了分析.     

碳酸盐共沉淀法制备Li[Li0.2Co0.13Ni0.13Mn0.54]O2中加料方式对产物性能的影响

采用碳酸钠和碳酸氢铵作为沉淀剂和络合剂,在水溶液中共沉淀Mn2+、Ni2+和Co2+以获得混合过渡金属元素的碳酸盐沉淀前驱体Mn0.675Ni0.1625Co0.1625CO3。并进一步合成高容量锂离子电池正极材料Li[Li0.2Co0.13Ni0.13Mn0.54]O2。考察了3种不同加料方式对共沉淀前驱体的结构、形貌和元素比例的影响,以及对最终产物的结构、形貌和电化学性能的影响。     

镍系复合氧化物Li_aNi_(0.78)Co_(0.2)Cd_(0.02)O_2的合成及电化学性能

以LiOH·H2O,含镉球状Ni(OH)2和Co2O3为原料,采用改进固相反应法合成镍系复合氧化物LiaNi0.78Co0.2Cd0.02O2锂离子电池正极材料,并通过ICP＿AES,XRD,SEM,TEM及电化学性能测试对该材料进行表征.实验表明,由Co和Cd部分取代Ni元素的复合正极材料LiaNi0.78Co0.2Cd0.02O2仍具有较完好的层状结构,表面分布均匀,颗粒粒径分布窄,且电化学性能稳定.常温下具有较高的可逆容量和优异的循环稳定性,其可逆容量最高达157.8mAh/g,循环50次后容量仍保持138.3mAh/g左右.     

层状化合物La2Ni1-yCoyO4+δ的合成、结构与性能

采用氨基多羧酸配合物法合成La2Ni1-yCoyO4+δ(y=0~0.2)超细粉料, 研究陶瓷样品的结构和混合导电性能. 研究结果表明, La2Ni1-yCoyO4+δ具有正交结构(Fmmm空间群), Co离子取代增加了钙钛矿层中ab平面上Ni/Co—O键的键长、岩盐层中沿c 轴方向上La—O键的键长和非化学计量氧含量, 并有利于改善材料的烧结性能. 随着Co离子含量的增加, 总电导率的峰值温度向高温移动, 高温段总电导率随温度的变化趋于平缓, 但总电导率水平出现降低; 增加Co离子含量还有利于提高氧离子导电性能. Co离子取代对陶瓷样品混合导电性能的影响与晶体结构参数的变化紧密相关.     

Gd1-xSrxCoO3-δ和Gd0.8Sr0.2Co1-yFeyO3-δ系阴极材料的制备和性能

采用甘氨酸-硝酸盐(GNP)法合成了新型中温固体氧化物燃料电池(IT.SOFC)的阴极材料Gd1-xSrxCoO3-δ(x=0-0.5)和Gd.0.8Sr0.2Co1-yFeyO3-δ(y=0-1),所合成的初始粉体在800℃下煅烧12 h后均形成了钙钛矿结构的单相固溶体.研究发现,Gd1-xSrxCoO3-δ(GSC)的电导率在600℃时达到了559 S·cm-1,由Ce0.8Cd0.2O2-δ(GDC)电解质和GSC-25GDC材料组成的对称电极在600℃和700℃的界面阻抗分别为0.170Ω·cm2和0.064Ω·cm2,活化能仅为87.8 kJ·mol-1,预示其可以作为ITSOFC较为理想的阴极备选材料;随着Fe3 离子含量的增加,Gd0.8Sr0.2Co1-yFeyO3-δ系列阴极材料的热膨胀系数显著降低,但其电导率也急速下降;此外,通过调整Gd0.8Sr0.2CoO3-δ与GDC的比例可以制备出热膨胀系数与GDC电解质匹配、性能良好的Cd0.8Sr0.2CoO3-δ/GDC复合阴极材料.     

固-溶法制备中温固体氧化物燃料电池高性能La_(0.8)Sr_(0.2)MnO_3-Ba_(0.5)Sr_(0.5)Co_(0.8)Fe_(0.2)O_3阴极（英文）

研究了新型固溶法合成La0.8Sr0.2MnO3(LSM)包覆Ba0.5Sr0.5Co0.8Fe0.2O3(BSCF)复合粉体(LSM-BSCF),并探讨了其作为中温固体氧化物燃料电池阴极材料的电化学性能.LSM-BSCF阴极结合了LSM和BSCF阴极的优点,不仅增大了三相界面,而且稳定了微观结构.当温度为600儃750°C时,其极化阻抗为0.61儃0.09Ω·cm2.与溶液注入法制备的高性能电极相比,极大地提高了性能稳定性.     

La0.6Sr0.4Co0.8Fe0.2O3钙钛矿复合氧化物的柠檬酸盐法合成与导电性能

采用柠檬酸盐法合成出La0.6Sr0.4Co0.8Fe0.2O3钙钛矿复合氧化物超细粉料,考查了各种影响溶胶与凝胶的形成以及合成粉料晶体结构与颗粒形态的因素,并确定了最佳的合成条件。研究了烧成温度对La0.6Sr0.4Co0.8Fe0.2O3电导率的影响,发现1200℃是最合适的烧成温度。研究结果表明,在室温～900℃范围内,样品的电导率在600℃附近出现峰值(～103S·cm-1),在低温段样品的导电行为符合小极化子导电机制,不同烧成温度的样品的导电活化能基本一致(5.31～5.79kJ·mol-1)。与常规固相合成法相比,柠檬酸盐法合成的La0.6Sr0.4Co0.8Fe0.2O3具有更高的烧结活性和电导率。     

高性能Sm0.5Sr0.5CoO3阴极的制备与表征

用固相合成法合成了Sm0.5Sr0.5CoO3 (SSC)中温固体氧化物燃料电池阴极材料.以La0.9Sr0.1Ga0.8Mg0.2O3为电解质,利用多种技术考察了不同温度(1173～1373 K)焙烧的SSC阴极,以及1173 K 焙烧、掺杂La0.8Sr0.2Ga0.8Mg0.15Co0.05O3(LSGMC5)或La0.8Sr0.2Ga0.8Mg0.09Co0.11O3 (LSGMC11)高氧离子电导材料的复合SSC阴极.SEM的结果显示,随着电极焙烧温度的增加,电极的颗粒度增大,孔隙度减小；LSGMC5、LSGMC11的掺杂对电极微观结构影响不大.交流阻抗和极化实验的结果表明,SSC电极的活性随电极焙烧温度的增加而减小,电极的最佳焙烧温度在1173 K左右；掺杂了LSGMC5或LSGMC11的复合SSC电极的活性以及稳定性显著高于SSC电极.     

Mg_2Ni_(1-x)Co_x合金相的固溶烧结法制备及结构和储氢性能

采用固溶烧结法制备了Mg_2Ni_(1-x)Co_x(x=0.10,0.15,0.20)合金,利用X射线衍射仪和压力-组成-温度测试仪等研究了Co含量对合金相结构和储氢性能的影响.结果表明,合金由Mg_2Ni型Mg_2(Ni,Co)主相及少量Mg和Mg Ni3Co新相组成.Mg2(Ni,Co)具有良好的可逆储氢性能,吸氢形成Mg_2Ni_(0.9)Co_(0.1)H_4型四元氢化物,其具有与父系氢化物HT-Mg_2NiH_4相近的放氢焓变(ΔHd=63.9 k J/mol H2).Mg_2Ni_(1-x)Co_x(x=0.10,0.15,0.20)合金具有良好的放氢动力学性能,二维相界面迁移为放氢过程的控制步骤.随着Co含量的增加,合金的放氢活化能(Ea)降低,其中,Mg_2Ni_(0.8)Co_(0.2)的Ea降低到54.0 k J/mol.     

侧臂冠醚的合成及其准聚轮烷的组装与表征

由间苯二酚和邻苯二酚出发, 经七步反应合成了带4,4’-联吡啶正离子识别点的32-冠-10和31-冠-10三种侧臂冠醚, 并用NMR, IR, ESI-MS进行了结构表征. 通过1H NMR实验研究了三种侧臂冠醚在溶液中的自组装行为. 结果表明冠醚中氢的化学位移随浓度的改变而变化, 在浓溶液中侧臂冠醚单体通过超分子自组装形成了线性链状准聚轮烷. 同时, 还通过热重分析法研究了三种侧臂冠醚的热稳定性.     

可溶性8-羟基喹啉铝衍生物电致发光材料的合成及性质

本文设计合成了五种可溶性8-羟基喹啉合铝的衍生物，结构经红外、核磁共振及元素分析表征，并对它们的光致发光以及分子结构与发光性能的关系进行了研究。     

负载型钌/铝钛复合载体上的二氧化碳甲烷化反应

用浸渍法制备了铝钛复合载体担载的钌催化剂，考察了它们对二氧化碳甲烷化反应的催化性能，结果表明，高TiO2含量载体制备的催化剂的活性和选择性较高，同时考察了反应温度、空速、金属担载量以及添加第二金属组分等对催化剂性能的影响．     

Solution,thermal and optical properties of new poly(pyridinium salt)s derived from conjugated quinoline diamines

Several new poly(pyridinium salt)s with quinoline diamine moieties in their backbones with tosylate and triflimide counterion were prepared by either a ring‐transmutation polymerization reaction with bis(pyrylium tosylate) with a series of isomeric quinoline diamines in dimethyl sulfoxide (DMSO) for 48 h at 130–140 °C or a metathesis reaction of the tosylate polymers with lithium triflimide in DMSO at about 60 °C. Their chemical structures were confirmed by FTIR, ¹H and ¹³C NMR spectroscopy, and elemental analysis. Their number‐average molecular weights (M_n) were in the range of 18,000–58,000, and their polydispersities were in the range of 1.12–1.53 as determined by gel permeation chromatography. They had thermal stability in the temperature range of 353–455 °C and glass‐transition temperatures >240 °C. They had good solubility in common organic solvents and were characterized with polarizing optical microscopy (POM) studies for their lyotropic liquid‐crystalline properties. Their light‐emission properties were examined by spectrofluorometry in both the solution and film states. Their quantum yields were also determined. Additionally, their morphologies in the thin‐film states and melt‐drawn fibers were examined with POM, scanning electron microscopy, and transmission electron microscopy techniques. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Solution,thermal and optical properties of novel poly(pyridinium salt)s derived from conjugated pyridine diamines

Several novel poly(pyridinium salt)s with heterocyclic pyridine moieties in their backbones with tosylate and triflimide counterions were prepared by either ring‐transmutation polymerization reaction of phenylated‐bis(pyrylium tosylate) with isomeric pyridine diamines of 4‐phenyl‐2,6‐bis(4‐aminophenyl)pyridine in dimethyl sulfoxide (DMSO) for 48 h at 130–140 °C or by metathesis reaction of the respective tosylate polymers with lithium triflimide in DMSO at about 60 °C. Their chemical structures were characterized by FTIR, ¹H, ¹³C NMR spectroscopy, and elemental analysis. Their number‐average molecular weights (M_n) were in the range of 8,000–51,000 and their polydispersities in the range of 1.18–2.13 as determined by gel permeation chromatography. They had excellent thermal stabilities of 340–458 °C and high glass transition temperatures >200 °C. As they showed good solubilities in common organic solvents, their solution properties were also characterized for their lyotropic liquid‐crystalline properties with polarizing optical microscopy (POM) studies. Their photoluminescent properties were examined by using a spectrofluorometer in both solution and solid states. Their quantum yields were rather low, which were in the range of 1.3–2.0%. Additionally, hand‐drawn fibers from the melts were examined to determine their morphologies with a number of microscopic techniques including POM, scanning electron microscopy, and transmission electron microscopy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

The Synthesis and Anticronvulsant Activity of Some α-Halo-m-Trif luoromethyl Cinnamamides

Nine a-halo-m-trifluoromethgl cinnamides were synthesized from trifluoromethyl benzene,via bromination,Grignard reaction,condensation,halogen addition reactions etc,as indicated in the synthetic scheme.Their configurations were confirmed by 1H NMR.Their pharmacological results showed that the introduction of a-halogen group do not enhance their anticonvulsant activity as expected.     

含β-二酮的光致变色化合物的合成、结构表征及 其性能研究

合成了5种对羧基苯基重氮基β-二酮化合物,并与光致变色化合物相连,得到5种新型的多功能化合物。用元素分析、IR、^1HNMR和MS确定了其结构;研究了其紫外-可见光谱、荧光光谱及光致变色性;对化合物与Eu生成的配合物与DNA相互作用的性能进行了初步探讨,并对不同配体的配合物与DNA相互作用的情况进行了比较。     

用IR和负离子FAB—MS测定EDTA,DTPA及其碱金属盐类结构

用ＩＲ和负离子ＦＡＢ－ＭＳ测定不同ｐＨ值下ＥＤＴＡ，ＤＴＰＡ，及其碱金属盐类，能直接给出它们的结构及其分子量，对于其碱金属盐类的混合物，不经分离，可以直接测定，能同时得到混合物中各组分的相对分子质量。     

端烯基液晶冠醚的合成及其性质的研究

合成了端烯基液晶冠醚新化合物,通过紫外光谱、红外和拉曼光谱以及质谱对液晶冠醚的结构进行了详细的分析;并利用差示量热扫描(DSC)方法和热台偏光显微镜研究了液晶冠醚的热性质及织构,探讨了液晶冠醚的结构与相态的关系。     

新型荧光试剂N-9-吖啶基氨基乙酸及其甲酯的合成

设计合成了新型荧光试剂N-9-吖啶基氨基乙酸及N-9-吖啶基氨基乙酸甲酯,其结构经IR,^1H NMR表征,并初步讨论了它们的荧光性质及UV性质。可望应用于金属离子和有机高分子的检测及免疫分析等方面。