Inverted Perovskite Solar Cells Based on Small Molecular Hole Transport Material C8‐Dioctylbenzothienobenzothiophene

The small organic molecular Dioctylbenzothienobenzothiophene (C₈‐BTBT) has been explored as hole transport material (HTM) to replace PEDOT:PSS in inverted perovskite solar cells (PVSCs). MAPbI₃ perovskite films depositd onto C₈‐BTBT are smooth and uniform, with negligible residual of PbI₂ and large grain size even larger than 1 μm. Our champion C₈‐BTBT based devices reached a high power conversion efficiency (PCE) of 15.46% with marginal hysteresis, much higher than that of 11.50% achieved using PEDOT:PSS. Besides, devices adopting C₈‐BTBT as substrate show superior stability compared with the PEDOT:PSS based devices when stored under ambient conditions with a relative humidity of (25±5)%.     

Solid‐state NMR as a tool to describe and quantify the morphology of photoactive layers used in plastic solar cells

The optimization and control of the nanomorphology of thin films used as active layer in bulk heterojunction (BHJ) plastic solar cells is of key importance for a better understanding of the photovoltaic mechanisms and for increasing the device performances. Hereto, solid‐state NMR relaxation experiments have been evaluated to describe the film morphology of one of the “work‐horse” systems poly(2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene‐vinylene)/[6, 6]‐phenyl‐C₆₁butyric acid methyl ester (MDMO‐PPV/PCBM) in a quantitative way. Attention is focused on the influence of the processing solvent (toluene vs. chlorobenzene), the blend composition, and the casting technique, that is, spin coating versus doctor blading. It is demonstrated that independently of the solvent and casting technique, part of the PCBM becomes phase separated from the mixed phase. Whereas casting from toluene results in the development of well‐defined PCBM crystallites, casting from chlorobenzene leads to the formation of PCBM‐rich domains that contain substructures of weakly organized PCBM nanoclusters. The amount and physico‐chemical state of the phase separated PCBM is quantified by solid‐state NMR relaxation times experiments. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Low‐potential facile electrosynthesis of free‐standing poly(1H‐benzo[g]indole) film as a yellow‐light‐emitter

High‐quality free‐standing poly(1H‐benzo[g]indole) (PBIn) films were synthesized electrochemically by direct anodic oxidation of 1H‐benzo[g]indole (BIn) in boron trifluoride diethyl etherate. PBIn films obtained from this medium showed good electrochemical behavior and better thermal stability with a conductivity of 0.29 S cm^?1. PBIn films with low band gap value (1.59 eV) were insoluble in acetone and tetrahydrofuran. The structure and morphology of the polymer were studied by UV–vis, FTIR, and scanning electron microscopy, respectively. The results of quantum chemistry calculations and the spectroscopies of dedoped PBIn indicate that the polymerization of BIn mainly occurs via C₍₂₎ and C₍₅₎ position. The polymer film was compact with regular nanoparticles on the surface. Fluorescent spectral studies indicate that solid‐state PBIn film is a good yellow‐light‐emitter. Thermal stability of PBIn film is higher than poly(indole‐6‐carboxylic acid), poly(5‐formylindole), and polyindole. To the best of our knowledge, this is the first report on the electrosynthesis of free‐standing polyindole derivatives as yellow‐light‐emitter. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2730–2738     

Controlled self‐assembly of porphyrin/fullerene donor–acceptor complex in a polymer thin film

Thin films composed of polycyclohexane (PCHE), zinc(II)‐5,10,15,20‐tetra‐(2‐naphthyl)porphyrin (ZnTNpP), and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) blends are prepared to investigate their potential for the controlled self‐assembly of a porphyrin/fullerene donor–acceptor complex in a polymer thin film. The compatibilities of PCHE/PCBM (p), PCHE/ZnTNpP (q), and ZnTNpP/PCBM (r) in these blends have a significant effect on the dispersion of the ZnTNpP/PCBM donor–acceptor complex in the PCHE thin film. When the compatibilities are p << q, r, and q ≈ r, the ZnTNpP/PCBM donor–acceptor complex is formed between the PCHE and PCBM phases. This concept to form a controlled self‐assembly of the ZnTNpP/PCBM donor–acceptor complex may be applied to various combinations of porphyrin/fullerene systems in polymer thin film solar cells to achieve excellent performance. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 743–746     

Enhancing the electrochromic characteristics of conjugated polymer with TiO2 nano‐rods

Organic soluble, oleic acid capped TiO₂ nano‐rod was well‐mixed with the electrochromic polymer: Poly‐(4,4‐dioctylcyclopenta[2,1‐b:3,4‐b′]‐dithiophene (PDOCPDT) to form TiO₂/PDOCPDT nanocompsoite. TiO₂/PDOCPDT film showed high electrochemical stability and its coloration efficiency is 1.5 times of that for pure PDOCPDT. The function of TiO₂ nano‐rods can be regarded as a dispersion agent. PDOCPDT chains in TiO₂/PDOCPDT may have a less aggregated structure and more open morphology, therefore has higher coloration efficiency. TiO₂ may also act as electron transport or temporary electron storage centers, electrons can be transferred reversibly between PDOCPDT and TiO₂ nano‐rods. TiO₂/PDOCPDT is well‐soluble in CHCl₃, large area thin films can be fabricated reproducibly simply by spin coating. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1121–1130, 2008     

New carbazole‐based conjugated polymers containing pyridylvinyl thiophene units for polymer solar cell applications: Morphological stabilization through hydrogen bonding

We have synthesized two conjugated polymers ( P1 , P2 ) containing alternating electron‐donating and ‐accepting units, based on N‐alkyl‐2,7‐carbazole, 4,7‐di(thiophen‐5‐yl)‐2,1,3‐benzothiadiazole and 3‐[2‐(4‐pyridyl)vinyl]thiophene units. These conjugated polymers contained different contents of pyridine units, which were incorporated to form hydrogen bonds with [6,6]‐phenyl‐C₆₁‐butyric acid (PCBA). When these hydrogen bonding interactions were present in the polymer thin films, their thermal stability improved; deterioration, which occurred through aggregation of PCBA methyl ester after lengthy annealing times, was also suppressed. The power conversion efficiency of a device incorporating the film featuring hydrogen bonding interactions remained at 75% of the original value after thermal annealing for 5 h at 140 °C. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic properties of two‐dimensional copolymers based on novel benzothiadiazole and quinoxaline acceptors with conjugated dithienylbenzothiadiazole pendants

Two novel acceptors of benzo[c][1,2,5]thiadiazole and quinoxaline with conjugated dithienylbenzothiadiazole pendants were first designed and synthesized for building efficient photovoltaic copolymers. Based on benzo[1,2‐b;3,4‐b′]dithiophene donors and the two acceptors, two new copolymers have been prepared by Stille coupling polymerization. The resulting copolymers were characterized by ¹H NMR, gel permeation chromatography, and thermogravimetric analysis. UV–Visible absorption and cyclic voltammetry measurements indicated that the two copolymers possessed strong and broad absorption in the range of 300–700 nm, and deep‐lying energy levels of highest occupied molecular orbitals. The polymer photovoltaic devices based on benzo[c][1,2,5]thiadiazole‐based copolymer/phenyl‐C₇₁‐butyric acid methyl ester exhibited a power conversion efficiency of 2.42%, attributed to its relatively better light‐harvesting ability and active film morphology. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 668–677     

Impact of environmentally friendly processing solvents on the properties of blade‐coated polymer solar cells

High‐performance polymer solar cells (PSCs) are typically fabricated by spin coating in inert atmosphere from toxic halogenated solvents such as 1,2‐dichlorobenzene (o‐DCB) and chlorobenzene. This fabrication process is potentially hazardous for both the humans and the environment and dramatically impacts the possibility for the organic photovoltaic technology to be adopted at large scale. In this work, efficient PSCs blade coated in air using nonhalogenated 1,2,4‐trimethylbenzene (TMB) as processing solvent are demonstrated. The active layer, based on a previously synthesized benchmark polymer PFQ2T‐benzodithiophene blended with [6,6]‐phenyl‐C61‐butyric acid methyl ester (PC₆₁BM), showed an enhanced solid‐state aggregation induced by the use of TMB. Compared to o‐DCB‐processed devices, the solar cells fabricated from TMB resulted 10% more efficient with a power conversion efficiency of 4.20%. Interestingly, the improved photovoltaic performance resulted from the combination of synergic effects promoted by a more favorable film morphology, such as high exciton dissociation efficiency and lower bimolecular recombinations resulting in higher charge collection efficiency at the electrodes. The positive effect of TMB, compared to that of commonly employed halogenated solvents, confirms the great potential of this approach for the development of efficient PSCs for practical applications with reduced environmental impact. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 487–494     

Synthesis and photochemical reaction of cyclic oligomers: Synthesis and photopolymerization of novel C‐methylcalix[4]resorcinarene and p‐alkylcalix[n]arene derivatives containing spiro ortho ether groups

New photoreactive calixarene derivatives containing spiro ortho ester groups (calixarenes 3a–3c ) were synthesized by the reaction of 2‐bromomethyl‐1,4,6‐trioxaspiro[4.4]nonane with 2,8,14,20‐tetramethyl‐4,6,10,12,16,18,22,24‐octakis(carboxymethoxy)calix[4]resorcinarene, 5,11,17,23,29,35‐hexamethyl‐37,38,39,40,41,42‐hexakis(carboxymethoxy)calix[6]arene, and 5,11,17,23,29,35,41,47‐octa‐tert‐butyl‐49,50,51,52, 53,54,55,56‐octakis‐(carboxymethoxy)calix[8]arene, which were prepared by the reaction of C‐methylcalix[4]resorcinarene, p‐methylcalix[6]arene, and p‐tert‐butylcalix[8]arene, respectively. The thermal stability of the obtained calixarene derivatives containing spiro ortho ester groups was examined with thermogravimetric analysis, and it was found that these calixarene derivatives had good thermal stability. The photoinitiated cationic polymerization of spiro ortho ester groups in calixarene derivatives 3a–3c was examined with certain photoacid generators in the film state. Interestingly enough, the reaction of calixarene derivatives did not proceed with only photoirradiation; however, the reaction proceeded smoothly when the photoirradiation was followed by heating. Furthermore, calixarene 3a , composed of a C‐methylcalix[4]resorcinarene structure, showed the highest photochemical reactivity in this reaction system. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1293–1302, 2002     

Photofabrication of surface relief gratings from azobenzene containing perfluorocyclobutane aryl ether polymer

An azobenzene based perfluorocyclobutane (PFCB) aryl ether polymer, poly[4‐(phenylazo)triphenylamine‐1,2‐hexafluorocyclobutyl ether], was synthesized by using a palladium catalyzed amination reaction and the 2π + 2π cyclodimerization of 4‐[(trifluorovinyl)oxy]bromobenzene. This polymer was designed and synthesized to permit azo chromophores to be incorporated, thus introducing photoinduced dynamic behavior into the PFCB containing polymer structure. The polymer exhibited a T_g of about 122 °C, and the maximum absorption of the azo chromophores was 407 nm in the film state. A thin film was prepared through a spin coating process, and the rapid growth of diffraction efficiency was then achieved by irradiation with an interference beam. The efficient formation of holographic surface relief gratings was also verified from AFM images, which show regularly defined and aligned grating structures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3525–3532, 2005     

Conductive triethylene glycol monomethyl ether substituted polythiophenes with high stability in the doped state

Synthesis of two conducting polymers containing 3‐hexylthiophene and 3‐[2‐(2‐(2‐methoxyethoxy)ethoxy)ethoxy]thiophene is demonstrated. In thin‐film transistors, the high‐molecular‐weight polymer shows an average mobility of 4.2 × 10^?4 cm² V^?1 s^?1. Most importantly, the polymers have high conductivity upon doping with iodine and also have high stability in the doped state with high conductivities measured even after 1 month. Furthermore, the doping causes transparency to thin films of the polymer and the films are resistant to common organic solvents. All these properties indicate a great potential for the iodine‐doped polymer to be used as an alternative to commercially available poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate). © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1079–1086     

Blue‐light‐emitting polyfluorene functionalized with triphenylamine and cyanophenylfluorene bipolar side chains

A new bipolar conjugated polyfluorene copolymer with triphenylamine and cyanophenylfluorene as side chains, poly{[9,9‐di(triphenylamine)fluorene]‐[9,9‐dihexyl‐fluorene]‐[2,7‐bis(4′‐cyanophenyl)‐9,9′‐spirobifluorene]} ( PTHCF ), was synthesized for studying the polymer backbone emission. Its absolute weight‐average molecular weight was determined as 4.85 × 10⁴ by using gel permeation chromatography with a multiangle light scattering detector. In contrast to the electronic absorption spectrum in dilute solution, the absorbance of PTHCF in thin film was slightly blue shifted. By comparison of the solution and thin‐film photoluminescence (PL) spectra, a red shift of Δλ = 8–9 nm was observed in the thin‐film PL spectrum. The HOMO and LUMO energy levels of the resulting polymer were electrochemically estimated as ?5.68 and ?2.80 eV, respectively. Under the electric‐field intensity of 4.8 × 10⁵ V cm^?1, the obtained hole and electron mobilities were 2.41 × 10^?4 and 1.40 × 10^?4 cm² V^?1 s^?1, respectively. An electroluminescence device with configuration of ITO/PEDOT:PSS/ PTHCF _70%+PBD_30%/CsF/Ca/Al exhibited a deep‐blue emission as a result of excitons formed by the charges migrating along the full‐fluorene main chain. The incorporation of the bipolar side chains into the polymer structure prevented the intermolecular interaction of the fluorene moieties, balance charge injection/transport, and thereby improve the polymer backbone emission. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis of π‐conjugated copolymers composed of benzo[2,1,3]thiadiazole and thiophene units bearing various alkyl groups and their application to photovoltaic cells

π‐Conjugated polymers, PTOTBT , PTEHTBT , and PTt‐BTBT , composed of benzothiadiazole as an electron accepting unit and terthiophene as an electron donating unit in the backbone were prepared. PTOTBT , PTEHTBT , and PTt‐BTBT contained side chain groups of n‐octyl, 2‐ethylhexyl, and t‐butyl groups, respectively. Solubility, optical and thermal properties of the polymers showed strong dependences on their side chain groups. PTEHTBT having 2‐ethylhexyl groups in the side chain exhibited absorption maximum (λ_max) at longer wavelength (565 nm) than PTOTBT (534 nm) and PTt‐BTBT (495 nm). PTOTBT showed higher thermal stability than the others. The prepared polymers were employed to polymer solar cells (PSCs) with a configuration of ITO/PEDOT‐PSS/polymer: PC₆₁BH/LiF/Al. Power conversion efficiency of the PSC‐based on PTEHTBT was 1.32%. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Design and fabrication of electrospun polyethersulfone nanofibrous scaffold for high‐flux nanofiltration membranes

A novel class of high‐flux and low‐fouling thin‐film nanofibrous composite (TFNC) membranes, containing a thin hydrophilic top‐layer coating, a nanofibrous mid‐layer scaffold and a non‐woven microfibrous support, has been demonstrated for nanofiltration (NF) applications. In this study, the issues related to the design and fabrication of a polyethersulfone (PES) electrospun nanofibrous scaffold for TFNC NF membranes were investigated. These issues included the influence of solvent mixture ratio, solute concentration, additives, relative humidity (RH), and solution flow rate on the morphology of an electrospun PES nanofibrous scaffold, the distribution of fiber diameter, the adhesion between the PES scaffold and a typical poly(ethylene terephthalate) (PET) non‐woven support, as well as the tensile properties of the nanofibrous PES/non‐woven PET composite substrates. Uniform and thin nanofibrous PES scaffolds with strong adhesion to the nanofiber‐PET non‐woven are several of the key parameters to optimize the NF performance of TFNC membranes. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2288–2300, 2009     

Gas permeability and hydrocarbon solubility of poly[1‐phenyl‐2‐[p‐(triisopropylsilyl)phenyl]acetylene]

The effects of film thickness, physical aging, and methanol conditioning on the solubility and transport properties of glassy poly[1‐phenyl‐2‐[p‐(triisopropylsilyl) phenyl]acetylene] are reported at 35 °C. In general, the gas permeability coefficients are very high, and this polymer is more permeable to larger hydrocarbons (e.g., C₃H₈ and C₄H₁₀) than to light gases such as H₂. The gas permeability and solubility coefficients are higher in as‐cast, unaged films than in as‐cast films aged at ambient conditions and increase to a maximum in both unaged and aged as‐cast films after methanol conditioning. For example, the oxygen permeability of a 20‐μm‐thick as‐cast film is initially 100 barrer and decreases to 40 barrer after aging for 1 week at ambient conditions. After methanol treatment, the oxygen permeabilities of unaged and aged films increase to 430 and 460 barrer, respectively. Thicker as‐cast films have higher gas permeabilities than thinner as‐cast films. Propane and n‐butane sorption isotherms suggest significant changes in the nonequilibrium excess free volume in these glassy polymer films due to processing history. For example, the nonequilibrium excess free volume estimated from the sorption data is similar for as‐cast, unaged samples and methanol‐conditioned samples; it is 100% higher in methanol‐conditioned films than in aged, as‐cast films. The sensitivity of permeability to processing history may be due in large measure to the influence of processing history on nonequilibrium excess free volume and free volume distribution. The propane and n‐butane diffusion coefficients are also sensitive to film processing history, presumably because of the dependence of diffusivity on free volume and free volume distribution. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1474–1484, 2000     

Donor–acceptor photovoltaic polymers based on 1,4‐dithienyl‐2,5‐dialkoxybenzene with intramolecular noncovalent interactions

Donor–acceptor (D–A) conjugated polymers bearing non‐covalent configurationally locked backbones have a high potential to be good photovoltaic materials. Since 1,4‐dithienyl‐2,5‐dialkoxybenzene ( TBT ) is a typical moiety possessing intramolecular S…O interactions and thus a restricted planar configuration, it was used in this work as an electron‐donating unit to combine with the following electron‐accepting units: 3‐fluorothieno[3,4‐b]thiophene ( TFT ), thieno‐[3,4‐c]pyrrole‐4,6‐dione ( TPD ), and diketopyrrolopyrrole ( DPP ) for the construction of such D–A conjugated polymers. Therefore, the so‐designed three polymers, PTBTTFT , PTBTTPD , and PTBTDPP , were synthesized and investigated on their basic optoelectronic properties in detail. Moreover, using [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as acceptor material, polymer solar cells (PSCs) were fabricated for studying photovoltaic performances of these polymers. It was found that the optimized PTBTTPD cell gave the best performance with a power conversion efficiency (PCE) of 4.49%, while that of PTBTTFT displayed the poorest one (PCE = 1.96%). The good photovoltaic behaviors of PTBTTPD come from its lowest‐lying energy level of the highest occupied molecular orbital (HOMO) among the three polymers, and good hole mobility and favorable morphology for its PC₇₁BM‐blended film. Although PTBTDPP displayed the widest absorption spectrum, the largest hole mobility, and regular chain packing structure when blended with PC₇₁BM, its unmatched HOMO energy level and disfavored blend film morphology finally limited its solar cell performance to a moderate level (PCE: 3.91%). © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 689–698     

Synthesis and miscibility studies of [60]fullerenated poly(2‐hydroxyethyl methacrylate)

[60]Fullerenated poly(2‐hydroxyethyl methacrylate)s containing 0.6–3.0 wt % C₆₀ were synthesized. These polymers are soluble in methanol and N,N‐dimethylformamide (DMF). [60]Fullerenated poly(2‐hydroxyethyl methacrylate)s with higher C₆₀ contents are only sparingly soluble in DMF and virtually insoluble in other organic solvents. A loading of 1.2 wt % C₆₀ in poly(2‐hydroxyethyl methacrylate) does not greatly affect its miscibility with poly(N‐vinyl‐2‐pyrrolidone), poly(1‐vinylimidazole), and poly(4‐vinylpyridine). © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1157–1166, 2002     

Effect of adjacent hydrophilic polymer thin films on physical aging and residual stress in thin films of poly(butylnorbornene‐ran‐hydroxyhexafluoroisopropyl norbornene)

The properties of thin supported polymer films can be dramatically impacted by the substrate upon which it resides. A simple way to alter the properties of the substrate (chemistry, rigidity, dynamics) is by coating it with an immiscible polymer. Here, we describe how ultrathin (ca. 2 nm) hydrophilic polymer layers of poly(acrylic acid) and poly(styrene sulfonate) (PSS) impact the aging behavior and the residual stress in thin films of poly(butylnorbornene‐ran‐hydroxyhexafluoroisopropyl norbornene) (BuNB‐r‐HFANB). The aging rate decreases as the film thickness (h) is decreased, but the extent of this change depends on the adjacent layer. Even for the thickest films (h > 500 nm), there is a decrease in the aging rate at 100 °C when BuNB‐r‐HFANB is in contact with PSS. In an effort to understand the origins of these differences in the aging behavior, the elastic modulus and residual stress (σ_R) in the films were determined by wrinkling as a function of aging time. The change in the elastic modulus during aging does not appear to be directly correlated with the densification or expansion of the films, but the aging rates appear to roughly scale as hσ_R^1/3. These results illustrate that the physical aging of thin polymer films can be altered by adjacent polymers. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 992–1000     

Synthesis of through‐space conjugated polymers containing [2.2]paracyclophane and thieno[3,4‐b]pyrazine in the main chain

We synthesized through‐space conjugated polymers with [2.2]paracyclophane and thieno[3,4‐b]pyrazine units in the main chain by the Sonogashira–Hagihara coupling reaction. The obtained polymers were soluble in common organic solvents, and homogeneous thin films were readily obtained from the polymer solutions by spin‐coating techniques. The polymers exhibited the extension of the conjugation length via the through‐space interaction. The polymers showed orangish‐red emission with peak maxima of around 610 nm in diluted solutions and their thin films, which were derived from the thieno[3,4‐b]pyrazine moieties. The optical and electrochemical behaviors of the polymers containing pseudo‐para‐ and pseudo‐ortho‐linked [2.2]paracyclophane were identical. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2009     

Micron‐granula polyolefin with self‐immobilized nickel and iron diimine catalysts bearing one or two allyl groups

Self‐immobilized nickel and iron diimine catalysts bearing one or two allyl groups of [ArN?C]₂(C₁₀H₆)NiBr₂ [Ar = 4‐allyl‐2,6‐(i‐Pr)₂C₆H₂] ( 1 ), [ArN?C(Me)][Ar′N? C(Me)]C₅H₃NFeCl₂ [Ar = Ar′ = 4‐allyl‐2,6‐(i‐Pr)₂C₆H₃, Ar = 2,6‐(i‐Pr)₂C₆H₃, and Ar′ = 4‐allyl‐2,6‐(i‐Pr)₂C₆H₃] were synthesized and characterized. All three catalysts were investigated for olefin polymerization. As a result, these catalysts not only showed high activities as the catalyst free from the allyl group, such as [ArN?C]₂C₁₀H₆NiBr₂ (Ar = 2,6‐(i‐Pr)₂C₆H₂)], but also greatly improved the morphology of polymer particles to afford micron‐granula polyolefin. The self‐immobilization of catalysts, the formation mechanism of microspherical polymer, and the influence on the size of the particles are discussed. The molecular structure of self‐immobilized nickel catalyst 1 was also characterized by crystallographic analysis. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1018–1024, 2004