聚苯胺/醋酸纤维素复合膜的制备及其超级电容特性

通过电化学原位聚合法制备多孔网状结构的聚苯胺(PANI)/醋酸纤维素(CA)复合膜电极,该复合膜的内层(与电极接触的一面)呈墨绿色,外层呈白色。采用原子力显微镜(AFM)、扫描电镜(SEM)、红外光谱(FTIR)对其形貌和化学组成进行表征。通过循环伏安、恒电流充放电和电化学阻抗研究了复合膜电极的超级电容特性。结果表明,多孔网状结构的PANI/CA复合材料具有良好的电容性能,其比电容可达到410F/g,并且该超级电容器具有较小的内阻和较好的循环稳定性,300次循环后,容量仍维持在342F/g,比电容的保持率为83.4%。     

PANI/MWCNT电极在硫酸锂溶液中电容性能

化学氧化法制备聚苯胺/多壁碳纳米管复合材料(PANI/MWCNT),扫描电镜(SEM)、XRD及IR表征样品结构及形貌,电化学方法测定复合电极循环伏安曲线、恒流充放电曲线及电极交流阻抗.结果表明,PANI/MWCNT电极在1mol/L的Li2SO4溶液中具有较好电容性能,在电流密度为5mA/cm2时,比电容为412F/g.PANI/MWCNT电极较PANI电极有更好的大电流放电能力,50mA/cm2下复合电极的比电容仍达318F/g,为5mA/cm2时该电极比电容的77.2%,而PANI电极的比电容仅为其5mA/cm2时的56.2%.交流阻抗证明碳纳米管降低复合电极的电阻,显著提高大电流放电能力.     

对甲苯磺酸掺杂聚(苯胺/中性红)复合物的乳液聚合法制备及电化学电容行为

以对甲基苯磺酸(TSA)为掺杂剂和乳化剂, 过硫酸铵(APS)为引发剂, 采用现场乳液聚合方法合成了对甲基苯磺酸掺杂聚(苯胺/中性红)复合材料(TSA-PANI/PNR). 利用X射线衍射(XRD)和电子扫描显微镜(SEM)对共聚物复合材料的结构和形貌进行了分析和表征. 以此复合材料为活性物质制备电极, 以l mol/L H₂SO₄水溶液为电解液组装超级电容器, 通过恒电流充放电、循环伏安和交流阻抗等技术研究了其电化学性能. 研究结果表明, TSA-PANI/PNR电极具有比TSA/PANI更优良的电化学性能. 扫描速度为1 mV/s的循环伏安曲线计算结果表明, 其单电极比电容可达到1350 F/g, 而TSA/PANI在相同的扫速下其单电极比电容仅为1038 F/g; 在5 mA放电电流下, TSA-PANI/PNR组装的电容器首次充放电比电容可达到348 F/g, 1000次循环后容量保持87%.     

碳纳米管/聚苯胺/石墨烯复合纳米碳纸及其电化学电容行为

通过真空抽滤的方法制备碳纳米管纸,并对其进行循环伏安电化学氧化处理.以该电化学氧化处理的碳纳米管(CV-CNT)纸为基体,采用电化学聚合沉积聚苯胺(PANI),随后吸附石墨烯(GR),制备具有三明治夹心结构的碳纳米管/聚苯胺/石墨烯(CV-CNT/PANI/GR)复合纳米碳纸.该结构外层为GR,内层由PANI包裹的CNT形成网络骨架,充分发挥三者各自优势构建柔性电极材料.用场发射扫描电镜(FE-SEM)、透射电子显微镜(TEM)、拉曼光谱对其形貌与结构进行表征,并测试其电化学性能.研究发现:PANI呈纳米晶须状,并均匀包裹在CV-CNT表面;该复合碳纸具有良好的电容特性、大电流充放电特性以及良好的循环稳定性能.电流密度为0.5A·g-1时,比电容可达415F·g-1;20A·g-1时仍能保持106F·g-1的比电容.由于GR的保护作用,1000次循环之后较CV-CNT/PANI保持更高的有效比电容.该CV-CNT/PANI/GR复合碳纸展现出在高性能超级电容器柔性电极材料的潜在应用价值.     

石墨烯-氧化锌复合材料及其电化学性能

采用Hummers法制得氧化石墨,再经溶剂热法一步合成石墨烯-氧化锌复合材料（GZO）. 在6 mol·L^-1氢氧化钾电解液中,测试循环伏安曲线、交流阻抗谱图和计时电位曲线. 结果表明,石墨烯-氧化锌复合材料电极的比电容为115 F·g^-1,具有较好的循环寿命,改善了超级电容器的性能.     

电化学电容器氮化钒负极材料性能研究

利用高温氨解还原氧化钒（V₂O₅）制备了氮化钒（VN）纳米材料. 采用XRD、SEM与TEM观察分析样品的结构和形貌,采用氮气吸附、循环伏安曲线以及恒流充放电曲线测试样品的比表面积、孔径分布和电极电化学性能. 结果表明,VN样品属于立方晶系（Fm3m [225]）,其大小均一,近似球形,氨解时间的加长（12 h）,小颗粒间相互交联可形成一定的介孔. 50 mA?g-1电流密度下VN-c电极的比电容能达到192 F.g-¹,1000周期循环其比电容仍有150 F.g^-1,同时具有双电层电容性能和氧化还原反应的准电容性能.     

立方体咪唑骨架衍生镍钴氢氧化物的微波制备及其电化学性能

采用微波辅助加热法,以类沸石二甲基咪唑钴（ZIF-67）为模板和钴源,快速制备了三维中空结构的镍钴氢氧化物（Ni-Co LDH）。通过X射线衍射仪（XRD）、扫描电子显微镜（SEM）、X射线光电子能谱仪（XPS）、透射电子显微镜（TEM）和比表面积及孔径分析仪（BET）探究了微波反应时间对材料形貌、结构的影响;通过循环伏安法（CV）、恒电流充放电（GCD）曲线和电化学阻抗谱（EIS）分析了材料的电化学性能。结果显示,Ni-Co LDH-15 min电极材料的电化学性能最优：在0.5 A/g时,比电容高达2371.0 F/g;电流密度扩大20倍,材料具有较好的倍率性能（78.5%）。以镍钴氢氧化物为正极,活性炭为负极组装成非对称式超级电容器,在功率密度为448.05 W/kg时,能量密度高达19.17 W·h/kg,且循环5000圈后电容保持率高达88.7%,表明镍钴氢氧化物是一种具有优异电化学性能和实际应用潜力的超级电容器电极材料。     

自支撑三维功能化石墨烯/聚苯胺电极材料的制备及超级电容性能

采用水热法制备了三维石墨烯(3D-G),并以十八胺(ODA)为接枝剂对部分还原的氧化石墨烯进行氨基化处理,再利用原位聚合法在氨基化石墨烯表面生长聚苯胺,制备了十八胺功能化石墨烯/聚苯胺(G-ODA/PANI).对材料进行了结构表征、电化学性能分析和材料结构的比电容贡献分析.结果显示,电极材料的电容贡献大部分体现为材料的表面电容,G-ODA/PANI电极片在1 A/g电流密度时的比电容最高可达1080 F/g,是未功能化石墨烯/聚苯胺电极材料(G/PANI)的2.57倍,且循环稳定性也有很大的提高,循环10000周后的比容量保持率为90.8%,比G/PANI高9.6%.     

纳米纤维聚苯胺在电化学电容器中的应用

采用脉冲电流方法（PGM）合成了具有纳米纤维结构的导电聚苯胺（PANI）.扫描电子显微镜对膜层观察表明, PANI膜是由直径约为100 nm的掺杂态聚苯胺纤维交织而成.以纳米纤维状聚苯胺组成电化学电容器,研究了其电化学电容性能,并与恒电流方法（GM） 制备的颗粒状PANI电容器性能进行了比较.结果表明,在相同的沉积电量下,PGM制备的纳米纤维状PANI电化学电容器比颗粒状PANI电化学电容器具有更大的电容容量,其电化学电容器的比电容可高达699 F•g－1,能量密度为54.6 Wh•kg－1.并且该电化学电容器具有良好的充放电性能和循环寿命.     

聚苯胺纳米刺/掺氮空心碳球复合材料的制备及电容性能

以掺氮空心碳球（N-HCS）为骨架,通过化学氧化聚合法制备了聚苯胺纳米刺/掺氮空心碳球复合材料（PANI/N-HCS）,采用扫描电子显微镜、透射电子显微镜和红外光谱仪等对样品的形貌、结构等进行了表征. 采用循环伏安、计时电位和交流阻抗等方法在1 mol/L H₂SO₄水溶液中考察了材料的电化学性能. 结果表明,PANI/N-HCS具有良好的电化学性能,在0.5 A/g电流密度下,PANI/N-HCS的比电容达346 F/g;当电流密度为20 A/g时,PANI/N-HCS比电容值为228 F/g,电容保持率为66%;在5 A/g电流密度下,经1000次充放电循环后,电容保持率为76%.     

季铵盐掺杂聚苯胺电极的电容性能

采用循环伏安法,在铂电极表面聚合制备了季铵盐[CnH2n+1N(CH3)3]Cl(n=12,14,16,18)掺杂的聚苯胺修饰电极。 利用扫描电子显微镜、红外光谱以及X射线衍射对复合电极的表面形貌和结构进行了表征。 用循环伏安法、交流阻抗和恒电流充放电测试对电极的电化学性质和电容行为进行了系统研究。 结果表明,其中[C18H37N(CH3)3]Cl季铵盐掺杂的聚苯胺复合电极比表面积大,电容性能好,在2×10-3 A的充电电流下,初始比电容高达329.6 F/g,未掺杂电极比电容为199.0 F/g。 而且,复合电极的循环稳定性良好,经30次循环后比电容保持为252.4 F/g。     

铂-氧化铈/聚苯胺/聚砜复合膜电极的制备及对甲醇的电催化氧化

采用电化学聚合法制备了掺杂CeO2纳米粒子的聚苯胺(PAN)/聚砜(PSF)复合膜电极,在其上电沉积铂粒子,制得了铂-氧化铈/聚苯胺/聚砜的复合膜修饰电极。 复合膜的形貌和化学组分通过冷场发射扫描电子显微镜（Cold FE-SEM）和能量散射X射线谱（EDS）进行了表征,用循环伏安法和电化学交流阻抗法考察了复合膜电极对甲醇的电催化氧化性能。 结果表明,复合膜的双层多孔结构使铂粒子与CeO2粒子在复合膜内层的多孔聚苯胺上均匀沉积,粒子平均尺寸约为80 nm;CeO2为铂质量的7%时,铂-氧化铈/聚苯胺/聚砜复合膜修饰电极对甲醇有很好的电催化氧化性能和高的稳定性。     

低温合成樟脑磺酸掺杂聚苯胺微管的电化学电容行为

在低温条件下合成了长约为2-3 μm, 外径约为300-400 nm 的樟脑磺酸掺杂聚苯胺微管. 扫描电镜(SEM)和透射电镜(TEM)显示, 生成的聚苯胺微管管径受樟脑磺酸浓度的影响, 高浓度的掺杂剂有利于管状聚苯胺的形成. 采用交流阻抗、循环伏安、恒流充放电等测试技术对不同产物的电化学电容行为进行了研究, 结果表明, 苯胺单体与樟脑磺酸的摩尔比为1:1时所得掺杂态聚苯胺电极具有较好的循环稳定性, 单电极比电容达到522 F·g-1.     

Platinum-modified polyaniline/polysulfone composite film electrodes and their electrocatalytic activity for methanol oxidation

The polyaniline/polysulfone (PAN/PSF) composite films were prepared by electropolymerization, and then platinum was deposited into this composite film to obtain the platinum-modified polyaniline/polysulfone(Pt/PAN/PSF) composite film electrodes. Their component, morphology and structure were characterized by FTIR spectra, scanning electron microscopy and energy dispersive X-ray spectroscopy. The results show that the composite film has a bi-layer structure with asymmetrical pores, and the platinum particles are homogeneously dispersed in the modified film electrodes. The cyclic voltammetry and electrochemical impedance spectroscopy techniques were applied to investigate the electrochemical properties and the electrocatalytic activity of the modified film electrodes, which show a promotive action for methanol oxidation and the methanol oxidation under a diffusion-controlled process.     

The carbon nanotubes-polyaniline composites and their effect on catalytic properties of deposited catalysts

Composites of functionalized single-wall carbon nanotubes and polyaniline are deposited onto electrodes by in situ electrochemical polymerization. Their electrochemical behavior and differential capacitance are studied by cyclic voltammetry, electrochemical impedance spectroscopy, and chronovoltamperometry. The differential capacitance of the composite electrode exceeds that of pure polyaniline film deposited onto electrode, which can be explained by the nanotubes’ loosening effect on the polyaniline structure. The composite-electrode capacitance is as large as 1000 F g⁻¹ or higher. Thus obtained composite films were used as a support for deposited platinum-ruthenium catalyst. The Pt-Ru structure and catalytic properties in the methanol oxidation reaction are studied. It is shown that the specific current of methanol oxidation at Pt-Ru is larger by a factor of 7–15 than those measured when pure polyaniline, pure carbon nanotubes, or standard Vulcan XC-72 carbon black are used as supports. It is found that the catalytic activity is the same for all studied supports, provided the current is reduced to the unit of Pt-Ru true surface area. Thus, the observed large catalytic effect is associated with the structure and high dispersivity of the electrodeposited metals incorporated to the single-wall carbon nanotubes-polyaniline composite.     

Self-sustaining hybrid electrode prepared from polyaniline,carbon nanotubes,and carbon fibers: morphological,structural, and electrochemical analyses

The self-sustaining hybrid electrode was prepared via chemical polymerization of aniline in acid medium containing dispersed carbon nanotubes (CNT), using carbon fiber (CF) as conducting substrate. The ternary composites called PAni/CNT/CF were characterized in order to evaluate their morphologies, structures, and thermal properties. The influence of the polyaniline (PAni) layer in the ternary composite properties was studied considering different deposition times on CF samples (30, 60, and 90 min). The ternary composite morphologies were observed by scanning electron microscopy while thermal structural analyses were obtained using thermogravimetric measurements. The structural features were analyzed by Raman scattering spectroscopy and Fourier transform infrared spectroscopy (FTIR). The possible interactions between PAni and CNT were discussed on the basis of Raman and FTIR spectra. These spectroscopic analyses also confirmed that the PAni present in the composite is in the emeraldine (ES) salt form. Furthermore, the ternary composites were also evaluated by electrochemical measurements such as cyclic voltammetry (CV), galvanostatic charge–discharge, and electrochemical impedance spectroscopy (EIS) techniques. The results showed good charge storage capacity for ternary composites, in particular, for PAni/CNT/CF obtained with 90 min of deposition time, which exhibited specific capacitance of around 500 F g^?1. Therefore, this electrode was selected to build a prototype of type I supercapacitor. This device presented specific capacitance of around 143 F g^?1 after 3200 charge/discharge cycles.     

用于超级电容器电极材料的聚苯胺基碳(英文)

在不同温度下碳化硫酸掺杂的聚苯胺制备了含杂原子(氮和氧原子)的新型碳材料.分别通过扫描电镜、元素分析仪、X射线光电子能谱仪和比表面积测试仪对这些碳材料的形貌特征、元素组成、表面化学组成和比表面积进行了表征.用循环伏安法、恒电流充放电法和交流阻抗法对其进行了电化学性能的研究.研究结果表明,在温度为800℃下碳化聚苯胺得到的碳有很好的电化学性能,尽管它的比表面积很小(325m·2g-1),但在0.5A·g-1电流密度下其比电容高达153F·g-1.它的高比电容可能与其含有合适比例的杂原子(氮和氧原子)有关,因为合适比例的氮和氧杂原子能够产生最大的赝电容.这些结果表明这种碳材料是一种很有发展前景的超级电容器电极材料.     

基于聚多巴胺的氮掺杂碳材料的制备及其电化学性能

多孔碳材料由于高的比表面积、优异的电子传导率、良好的化学稳定性等优点在超级电容器电极材料领域被广泛研究。 碳材料的组成及表面孔结构直接影响其电化学性能,为进一步提高碳材料的电容性能,本文首次以聚多巴胺球为前体,KOH为活化剂,通过高温碳化成功制备了良好电化学性能的氮掺杂多孔碳材料。 通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)、 X射线粉末衍射(XRD)、傅里叶变换红外光谱(FT-IR)、X射线光电子能谱(XPS)和Raman光谱等对所制备的氮掺杂多孔碳材料进行了形貌及结构组成的表征。 在6 mol/L KOH电解液中, 采用循环伏安、恒电流充放电对多孔碳材料的电化学性能进行了研究。 结果表明,由于双电层电容和赝电容的协同作用,在电流密度为1 A/g时,材料的比电容可达269 F/g,充放电循环1000圈后电容仍可保留初始值的93.5%。     

Preparation of 3D MnO2/Polyaniline/Graphene Hybrid Material via Interfacial Polymerization as High‐Performance Supercapacitor Electrode

MnO₂/polyaniline/graphene composite as a supercapacitor electrode material was synthesized through an interfacial polymerization approach in the interface of oil/water phase. The as‐synthesized MPG is characterized by infrared spectroscopy, XRD, XPS, SEM and TEM, and its electrochemical performance is measured by cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy. The 3D nanostructure of MPG and loose nanorod structure of polyaniline (PANI) coated with round MnO₂ pellets could be clearly observed. The maximum energy density of MPG is 45.4 Wh/kg (at a power density of 67.8 kW/kg) and the highest power density is 229.2 kW/kg (at an energy density of 25.7 Wh/kg). The capacitance retentions after 500 cycles at the scan rate of 5 mV/s for MGP composite and PANI/graphene are 70.4% and 59.1%, respectively, and the capacitance values after 500 cycles are 158.4 F/g and 114.8 F/g, respectively. The improved performance of MPG is due to the 3D nanostructure, loose nanorod structure of PANI and stable support of graphene, which prevent the mechanical deformation effectively during the fast charge/discharge process and facilitate the diffusion of the electrolyte ions into the inner region of active materials. The composite material is very promising for the next generation of high‐performance supercapacitors electrode.