阳离子和两性表面活性剂在聚甲基丙烯酸甲酯表面的吸附行为

利用座滴法研究了阳离子表面活性剂十六烷基醚羟丙基季铵盐(C₁₆PC)、十六烷基聚氧乙烯醚羟丙基季铵盐(C₁₆(EO)₃PC)和两性离子表面活性剂十六烷基醚羟丙基羧酸甜菜碱(C₁₆PB)、十六烷基聚氧乙烯醚羟丙基羧酸甜菜碱(C₁₆(EO)₃PB)溶液在聚甲基丙烯酸甲酯(PMMA)表面上的润湿性质, 考察了表面活性剂类型及浓度对接触角的影响趋势. 研究发现: 低浓度条件下表面活性剂分子可能以平躺的方式吸附到固体界面, 且亲水基团靠近固体界面, PMMA表面被轻微疏水化; 在高浓度时则通过Lifshitz-van der Waals 作用吸附, 亲水基团在外, PMMA表面被亲水改性. 聚氧乙烯基团(EO基团)的引入对阳离子表面活性剂的接触角影响不大; 而含有聚氧乙烯基团的两性离子表面活性剂在PMMA界面上以类似半胶束的聚集体吸附, 大幅度降低接触角.     

支链化甜菜碱和阳离子表面活性剂在聚甲基丙烯酸甲酯表面的吸附及其润湿性质

利用座滴法研究了两性离子表面活性剂支链十六烷基(聚氧乙烯)_n醚羟丙基羧酸甜菜碱(n = 0, 3)和阳离子表面活性剂支链十六烷基(聚氧乙烯)_n醚羟丙基季铵盐溶液在聚甲基丙烯酸甲酯(PMMA)表面上的润湿性质,考察了表面活性剂类型、结构及浓度对接触角的影响趋势。研究发现,表面活性剂浓度低于临界胶束浓度(cmc)时,分子通过氢键以平躺的方式吸附到PMMA界面,亲水基团靠近固体界面, PMMA表面被轻微疏水化;表面张力和粘附张力同时降低,导致此阶段接触角随浓度变化不大。浓度高于cmc时,表面活性剂通过疏水作用吸附,亲水基团在外, PMMA表面被明显亲水改性,接触角随浓度升高显著降低。由于具有相同的支链烷基,表面活性剂类型变化和聚氧乙烯基团的引入对接触角影响不大。     

支链化阳离子和甜菜碱表面活性剂对聚四氟乙烯表面润湿性的影响

利用座滴法研究了支链化阳离子表面活性剂十六烷基羟丙基氯化铵(C₁₆GPC)和两性离子表面活性剂十六烷基羧酸甜菜碱(C₁₆GPB)在聚四氟乙烯(PTFE)表面上的吸附机制和润湿性质, 考察了表面活性剂浓度对表面张力、接触角、粘附张力、固液界面张力和粘附功的影响趋势. 研究发现, 低浓度条件下, 表面活性剂疏水支链的多个亚甲基基团与PTFE表面发生相互作用, 分子以平躺的方式吸附到固体界面; 支链化表面活性剂形成胶束的阻碍较大, 浓度大于临界胶束浓度(cmc)时, C₁₆GPC和C₁₆GPB分子在固液界面上继续吸附, 与PTFE作用的亚甲基基团减少, 分子逐渐直立, 固液界面自由能(γ_sl)明显降低. 对于支链化的阳离子和甜菜碱分子, 接触角均在浓度高于cmc后大幅度降低.     

芳基油酸酰胺羟丙基磺基甜菜碱的合成及性能

合成了3种具有不同疏水基团的新型磺基甜菜碱两性表面活性剂,通过红外光谱对它们的结构进行了表征。 用滴体积法测定表面活性剂水溶液在25 ℃下的表面张力,从而确定其临界胶束浓度(cmc)及临界胶束浓度下的表面张力(γcmc);采用罗氏泡沫仪考察了浓度、温度对其泡沫性能的影响;采用分水时间法考察了其乳化性能。 结果表明,随着芳环在烷基链中的体积增大,cmc以及γcmc增大,饱和吸附面积Amin增大,而饱和吸附量Γmax减小。 3种表面活性剂的起泡性随浓度增大而增加,到一定值后趋于稳定;泡沫稳定性随浓度增大逐渐增强;起泡性随着温度的升高而显著增加,泡沫稳定性随温度升高而显著降低。 3种表面活性剂的乳化能力随浓度增大而逐渐增强然后趋于稳定。     

阳离子表面活性剂溴代十六烷基吡啶胶束对2,4-二硝基氯苯水解反应的影响

阳离子表面活性剂溴代十六烷基吡啶(CPB)胶束对水中OH^-和2, 4-二硝基氯苯的反应有催化作用.随CPB浓度的增大, 反应速率常数开始时迅速增大, 然后趋于常数.OH^-浓度的增大使胶束催化水解的二级速率常数减小.CPB胶束对此反应的速率提高作用比十六烷基三甲基溴化扶胶束更有效.对这两种胶束催化作用的差异进行了讨论.     

纤维素丙酸酯-g-二乙二醇正十六烷基醚固-固相变材料的制备及性能

以二月桂酸二丁基锡(DBTDL)为催化剂,微晶纤维素为骨架材料,二乙二醇正十六烷基醚(E2C16)为相变材料,采用化学接枝法制备了系列纤维素丙酸酯-g-二乙二醇正十六烷基醚(CP-g-E2C16)固-固相变材料.利用傅里叶变换红外光谱(FTIR)、核磁共振氢谱(1H NMR)、差示扫描量热仪(DSC)、热重分析(TG)和X射线衍射(XRD)对CP-g-E2C16相变材料的结构和热性能进行了表征.结果表明,得到了E2C16的取代度和接枝含量分别为0.12~0.37和17.1%~33.4%的CP-g-E2C16固-固相变材料.CP-g-E2C16接枝共聚物的相变温度和相变焓分别为25~34℃和40~62 J/g,符合人的体感舒适温度范围.CP-g-E2C16固-固相变材料的耐热温度高于237℃,与E2C16相比提高21~40℃,有望应用于熔融纺丝法制备纤维素基储热调温纤维领域.     

新试剂1-(2-羟基-3,5-二硝基苯基)-3-[4-(苯基偶氮)苯基]-三氮烯的合成及与季铵盐型阳离子表面活性剂的显色反应

合成了新试剂1-(2-羟基-3,5-二硝基苯基)-3-[4(苯基偶氮)苯基]-三氮烯(HDNPAPT),研究了该试剂在NaOH介质中与阳离子表面活性剂漠化十六烷基三甲铵(CTMAB)、溴化十六烷基吡啶(CPB)、溴化十二烷基二苄铰(DDMBAB)形成1:3的紫红色离子缔合物显色体系.测定了显色体系表面活性剂的临界胶束浓度、表观摩尔吸光系数ε_(max)、符合比尔定律的范围.探讨了微量阳离子表面活性剂CMTAB、CPB和DDMBAB的测定方法,结果满意.     

十六烷基氯化吡啶溶剂气浮的热力学及动力学研究

研究了表面活性剂十六烷基氯化吡啶(HPC)的溶剂气浮回收动力学及热力学规律。通过测定不同温度及浓度下HPC的表面张力, 得到了HPC在气-液界面的标准吸附表面自由能为-33.17 kJ/mol。HPC的溶剂气浮过程符合一级动力学方程,表观速率常数k的值随气体流速升高而增加,随温度升高而降低。     

皂荚素的表面活性及其二元体系的热力学研究

通过表面张力的测定研究了皂荚素(GS)的表面活性及其热力学性质随温度的变化.测定了皂荚素分别与十二烷基磺酸钠、十二烷基聚氧乙烯醚硫酸钠、全氟辛酸钠、十二烷基脂肪醇聚氧乙烯(9)醚、辛基酚聚氧乙烯(10)醚及十六烷基三甲基溴化铵等复配的表面张力-浓度对数关系(γ～lgc)曲线,并用二维晶格模型及正规溶液理论计算了含皂荚素的二元表面活性剂溶液表面吸附层的组成、分子相互作用参数及分子交换能.结果表明,皂荚素主要呈现非离子表面活性剂的性质,与阳离子表面活性剂复配呈微弱的离子性.复配后分子交换能均小于零,复配增效.增效顺序为GS/阳离子>GS/非离子>GS/阴离子(表面活性剂复配体系).     

聚合物对非离子十二烷基聚氧乙烯聚氧丙烯醚浊点的影响

测定了水溶性高分子聚乙二醇(PEC1000、PEG2000、PEG6000)和聚乙烯吡咯烷酮(PVP-K30、PVP-K90)对三种非离子表面活性剂十二烷基聚氧乙烯聚氧丙烯醚C12H25O(EO)m(PO)nH(LS36,m=3,n=6;LS5,m=4,n=5;LS54,m=5,n=4)浊点的影响.结果表明,聚乙二醇(PEG)可使三种表面活性剂水溶液浊点降低;而聚乙烯吡咯烷酮(PVP)随其浓度增加,表面活性剂溶液浊点先升高然后又下降;浊点下降程度与聚合物浓度和分子量有关.     

Effect of Cationic and Zwitterionic Surfactants on Contact Angle of Quartz–Water–Crude Oil System

The influences of four cationic surfactants hexadecyl glycidyl ether ammonium chloride and four zwitterionic surfactants hexadecyl glycidyl ether glycine Betaine solutions on contact angle of crude oil on a quartz surface were investigated using a captive drop method. The effects of surfactant type, structure, and concentration on contact angle were expounded. From obtained results it appears that the adsorbed surfactant at oil–water interface reduces the interfacial tension and the adsorption at quartz–water interface improves interfacial free energy, which results in reducing the stable value of contact angle and weakening dynamic behavior. At high concentration, the zwitterionic surfactant with branched-chain may form semi-micelle at quartz surface. As a result, the stable value of contact angle passes through a sharp minimum with the increasing concentration.     

Effect of anionic surfactant and short-chain alcohol mixtures on adsorption at quartz/water and water/air interfaces and the wettability of quartz

Measurements of the advancing contact angles for aqueous solutions of sodium dodecyl sulfate (SDDS) or sodium hexadecyl sulfonate (SHS) in mixtures with methanol, ethanol, or propanol on a quartz surface were carried out. On the basis of the obtained results and Young and Gibbs equations the critical surface tension of quartz wetting, the composition of the surface layer at the quartz-water interface, and the activity coefficients of the anionic surfactants and alcohols in this layer as well as the work of adhesion of aqueous solutions of anionic surfactant and alcohol mixtures to the quartz surface were determined. The analysis of the contact angle data showed that the wettability of quartz changed visibly only in the range of alcohol and anionic surfactant concentration at which these surface-active agents were present in the solution in the monomeric form. The analysis also showed that there was a linear dependence between the adhesion and the surface tension of aqueous solutions of anionic surfactant and alcohol mixtures. This dependence can be described by linear equations for which the constants depend on the anionic surfactant and alcohol concentrations. The slope of all linear dependence between adhesion and surface tension was positive. The critical surface tension of quartz wetting determined from this dependence by extrapolating the adhesion tension to the value equal to the surface tension (for contact angle equal zero) depends on the assumption whether the concentration of anionic surfactant or alcohol was constant. Its average value is equal to 29.95mN/m and it is considerably lower than the quartz surface tension. The positive slope of the adhesion-surface tension curves was explained by the possibility of the presence of liquid vapor film beyond the solution drop which settled on the quartz surface and the adsorption of surface-active agents at the quartz/monolayer water film-water interface. This conclusion was confirmed by the work of adhesion of aqueous solutions of anionic surfactants and short-chain alcohol mixtures to the quartz surface determined on the basis of the contact angle data and molar fraction of anionic surfactants and alcohols and their activity coefficient in the surface layer.     

缩水甘油苯基醚-缩水甘油正丁基醚共聚物磺酸钠的合成及表面活性

缩水甘油苯基醚-缩水甘油正丁基醚共聚物磺酸钠的合成及表面活性;缩水甘油苯基醚-缩水甘油正丁基醚共聚物磺酸钠; 合成; 表面性质; 胶束     

苄基取代甜菜碱对聚四氟乙烯表面润湿性的影响

利用座滴法研究了两性离子表面活性剂苄基取代烷基羧基甜菜碱(BCB)和苄基取代烷基磺基甜菜碱(BSB)在聚四氟乙烯(PTFE)表面上的润湿性质,考察了表面活性剂浓度对接触角的影响趋势,并讨论了粘附张力、固-液界面张力和粘附功的变化规律.研究发现,在低浓度时,表面活性剂通过疏水作用吸附到PTFE表面,疏水链苄基取代支链化使其在固-液界面上的吸附明显低于气-液界面,接触角在很大的范围内保持不变.当体相浓度增加到大于临界胶束浓度(cmc)时, BCB和BSB分子在固-液界面上继续吸附,分子逐渐直立,造成PTFE-液体之间的界面张力(γ_SL)进一步降低,表面亲水性增加,接触角随浓度增加明显降低;另一方面, BSB由于具有较大的极性头,在高浓度时空间阻碍作用明显,导致其对PTFE表面润湿性改变程度小于BCB.     

Correlation between surface free energy of quartz and its wettability by aqueous solutions of nonionic, anionic and cationic surfactants

The measurements of the advancing contact angle for water, glycerol, diiodomethane and aqueous solutions of Triton X-100 (TX-100), Triton X-165 (TX-165), sodium dodecyl sulfate (SDDS), sodium hexadecyl sulfonate (SHDS), cetyltrimethylammonium bromide (CTAB) and cetylpyridinium bromide (CPyB) on quartz surface were carried out. On the basis of the contact angles values obtained for water, glycerol and diiodomethane the values of the Lifshitz–van der Waals component and electron-acceptor and electron-donor parameters of the acid–base component of the surface free energy of quartz were determined. The determined components and parameters of the quartz surface free energy were used for interpretation of the influence of nonionic, anionic and cationic surfactants on the wettability of the quartz. From obtained results it was appeared that the wettability of quartz by nonionic and anionic surfactants practically does not depend on the surfactants concentration in the range corresponding to their unsaturated monolayer at water–air interface and that there is linear dependence between adhesional and surface tension of aqueous solution of these surfactants. This dependence for TX-100, TX-165, SDDS and SHDS can be expressed by lines which slopes are positive. This slope and components of quartz surface free energy indicate that the interaction between the water molecules and quartz surface might be stronger than those between the quartz and surfactants molecules. So, the surface excess of surfactants concentration at the quartz–water interface is probably negative, and the possibility of surfactants to adsorb at the quartz/water film–water interface is higher than at the quartz–water interface. This conclusion is confirmed by the values of the adhesion work of “pure” surfactants, aqueous solutions of surfactants and water to quartz surface. In the case of the cationic surfactants the relationship between adhesional and surface tension is more complicated than that for nonionic and anionic surfactants and indicates that the relationship between the adsorption of the cationic surfactant at water–air and quartz–water interface depends on the concentration of the surfactants in the bulk phase.     

Co-adsorption of carboxymethyl-cellulose and cationic surfactants at the air-water interface

We investigated the interaction between an anionic polyelectrolyte (carboxymethylcellulose) and cationic surfactants (DTAB, TTAB, and CTAB) at the air/water interface, using surface tension, ellipsometry, and Brewster angle microscopy techniques. At low surfactant concentration, a synergistic phenomenon is observed due to the co-adsorption of polyelectrolyte/surfactant complexes at the interface, which decreases the surface tension. When the surfactant critical aggregation concentration (cac) is reached, the adsorption saturates and the thickness of the adsorbed monolayer remains constant until another characteristic surfactant concentration, C0, is reached, at which all the polymer charges are bound to surfactant in bulk. Above C0, the absorbed monolayer becomes much thicker, suggesting adsorption of bulk aggregates, which have become more hydrophobic due to charge neutralization.     

Surfactant adsorption onto interfaces: measuring the surface excess in time

We propose a direct method to measure the equilibrium and dynamic surface properties of surfactant solutions with very low critical micellar concentrations (CMC) using a pendant drop tensiometer. We studied solutions of the nonionic surfactant hexaethylene glycol monododecyl ether (C(12)E(6)) and of the ionic surfactant hexadecyl trimethyl ammonium bromide (CTAB) with concentrated sodium bromide (NaBr). The variation of the surface tension as a function of surface concentration is obtained easily without the need for complex models and compares well with the result obtained using the Gibbs adsorption equation. The time-dependent surface concentration of each surfactant was also measured, and the adsorption process was found to be diffusion-controlled. The diffusion coefficients of the two surfactants can be extracted from the data and were found in very good agreement with literature values, further validating the method.