钛基TiO2纳米管阵列电极的光电催化性能

应用电化学阳极氧化法在纯Ti基底上制备高度有序的TiO2纳米管阵列,考察了Ti/TiO2光阳极的光电化学响应.以苯酚溶液为目标污染物,研究Ti/TiO2电极的光电催化性能,并与光催化性能进行比较.结果表明,该电极光电催化性能优于光催化性能.施加0.6 V电压时,光电催化性能最好.电化学阻抗谱分析显示,光电催化和光催化降解过程的速控步骤均为表面反应步骤,外加偏压减小了界面电荷转移阻抗,提高了光生载流子的分离效率.     

TiO_2纳米管阵列光电催化制氢研究进展

以TiO2纳米管阵列为光阳极组成的光电解池光电催化分解水是目前光催化制氢领域内研究最广泛的体系之一。本文综述了近年来TiO2纳米管阵列在光电催化分解水制氢领域的最新研究进展,重点阐述了提高TiO2纳米管阵列光电转换效率和产氢速率的方法,指出了目前存在的问题,并对今后的发展提出了展望。     

Improvement the wastewater purification by TiO2 nanotube arrays: The effect of etching-step on the photo-generated charge carriers and photocatalytic activity of anodic TiO2 nanotubes

The current study demonstrates how the etching step in anodization process effects on the photocatalytic activity of TiO₂ nanotubes. In this regard, the TiO₂ nanotubes were made by one-step and two-step anodization process on two different substrates Ti and etched-Ti foils, respectively. The results revealed that two-step anodization process is a beneficial way to prepare highly well-organized structure and regular surface. The two-step anodization by an enhancement in the fluoride ions diffusion led to a decrease in nanotubes' porosity and an increment in the nanotubes’ surface area, a factor of roughness, and the ratio of length to diameter, respectively. As a consequence of the improvement in geometrical properties, the two-step TiO₂ nanotubes led to the intensification of photocurrent density (from 0.383 to 0.677 mA cm⁻²⁾ and photoconversion efficiency (from 0.18% to 0.29%) in comparison with the one-step nanotubes, respectively. Further, a synergetic impact of the photoelectrochemical measurement and photocatalytic process was observed. The degradation efficiencies of 2,4-dichlorophenol by two-step nanotubes increased from 47 to 55% under visible light, and from 58 to72% under UV irradiation, which it was attributed to more light harvesting, more photo-generated electrons, higher separation efficiency and improvement in geometrical properties. Furthermore, the kinetic study showed that the reactions follow first-order kinetics and the reaction rate constants by two-step nanotubes are 1.25 and 1.44 times as great as those of one-step nanotubes under visible and UV irradiation, respectively. Moreover, the reusability tests showed that 2-step TiO₂ nanotubes has good stability and is active even up to the Fifth run.     

A facile one-step preparation of hierarchically-structured TiO2 nanotube array photoanodes with enhanced photocatalytic activity

Hierarchically structured TiO₂ (HST) films composed of top porous nanoparticle layer and underneath nanotube array layer are obtained by an anodization method on fluorine doped tin oxide surfaces. Compared with the TiO₂ nanotube arrays photoanode on Ti substrate, the HST photoanode exhibits a higher photoelectrocatalytic activity towards the oxidation of water and organics (e.g., glucose).     

Preparation and characterization of Zr doped TiO2 nanotube arrays on the titanium sheet and their enhanced photocatalytic activity

This paper described a new method for the preparation of Zr doped TiO₂ nanotube arrays by electrochemical method. TiO₂ nanotube arrays were prepared by anodization with titanium anode and platinum cathode. Afterwards, the formed TiO₂ nanotube arrays and Pt were used as cathode and anode, respectively, for preparation of Zr/TiO₂ nanotube arrays in the electrolyte of 0.1 M Zr(NO₃)₄ with different voltage and post-calcination process. The nanotube arrays were characterized by field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS) and UV-Vis diffusion reflection spectra (DRS). The photocatalytic activities of these nanotubes were investigated with Rhodamine B as the model pollutant and the results demonstrated that the photocatalytic efficiency of Zr doped TiO₂ nanotubes was much better than that of TiO₂ nanotubes under UV irradiation. Zr/TiO₂ nanotube arrays doped at 7 V and calcined at 600 °C (denoted as TiO₂-7 V-600) achieved the best photocatalytic efficiency and the most optimal doping ratio was 0.047 (Zr/Ti). TiO₂-7 V-600 could be reused for more than 20 times and maintained good photocatalytic activities.     

Enhanced Visible‐Light‐Induced Photoelectrocatalytic Degradation of Methyl Orange by CdS Sensitized TiO2 Nanotube Arrays Electrode

In this work, CdS sensitized TiO₂ nanotube arrays (CdS/TiO₂NTs) electrode was synthesized with the CdS deposition on the highly ordered titanium dioxide nanotube arrays (TiO₂NTs) by sequential chemical bath deposition method (S‐CBD). The as‐prepared CdS/TiO₂NTs was characterized by field‐emission scanning electron microscopy (FE‐SEM) and X‐ray diffraction (XRD). The results indicated that the CdS nanoparticles were effectively deposited on the surface of TiO₂NTs. The amperometric I‐t curve on the CdS/TiO₂NTs electrode was also presented. It was found that the photocurrent density was enhanced significantly from 0.5 to 1.85 mA/cm² upon illumination with applied potential of 0.5 V at the central wavelength of 253.7 nm. The photoelectrocatalytic (PEC) activity of the CdS/TiO₂NTs electrode was investigated by degradation of methyl orange (MO) in aqueous solution. Compared with TiO₂NTs electrode, the degradation efficiencies of CdS/TiO₂NTs electrode increased from 78% to 99.2% under UV light in 2 h, and from 14% to 99.2% under visible light in 3 h, which was caused by effective separation of the electrons and holes due to the effect of CdS, hence inhibiting the recombination of electron/hole pairs of TiO₂NTs.     

Sensitization of Mn with CdS nanoparticles via electrochemical deposition technique for photocurrent enhancement of nanomaterial’s-sensitized photoelectrochemical cells

A photoconversion efficiency of 2.12% was obtained under visible light illumination by nanostructure-sensitized photoelectrochemical cells using Mn/CdS as sensitizer loaded on TiO₂ nanotube arrays (NTAs) (Mn/CdS/TiO₂). Sensitization of Mn on CdS nanoparticles pre-loaded on TiO₂ NTAs was carried out by a two-step electrodeposition method. Compared with unsensitized TiO₂ NTAs, the photocurrent had increased from 0.03 to 4.12 for Mn/CdS/TiO₂ prepared at 1 min. The effects of deposited Mn on the physical, chemical, and photoelectrochemical properties of the CdS/TiO₂ NTAs nanostructure were investigated by using UV–visible diffuse reflectance spectroscopy, X-ray diffractometry, and field-emission scanning electron microscopy coupled with energy dispersive X-ray spectroscopy. The photoelectrochemical analysis was examined in a three-electrode system under a halogen illumination by using the prepared film as the photo-anode.     

Enhancement of ethanol electrooxidation on plasmonic Au/TiO2 nanotube arrays

Novel electrocatalysts Au/TiO₂ nanotube arrays (Au/TiO₂NTs) were prepared by loading low-content(1.9 at.%) of Au nanoparticles (AuNPs) onto highly ordered TiO₂ nanotube arrays (TiO₂NTs). Ethanol electrooxidation indicates that visible-light (λ > 400 nm) irradiation can significantly enhance the activity as well as resistpoisoning of Au/TiO₂NTs electrocatalysts that are activated by plasmon resonance. Au/TiO₂NTs catalysts calcinated at 300 °C display the highest performance due to the strong synergistic interactions between TiO₂ and Au NPs. The combination of visible-light irradiation with a controllable potential offers a new strategyfor enhancing the performance of anodes in direct ethanol fuel cell (DEFC).     

The Synthesis and Photocatalytic Properties of TiO2 Nanotube Array by Starch‐Modified Anodic Oxidation

In this study, the characterization and photocatalytic activity of TiO₂ nanotube arrays prepared by anodization process with starch addition were investigated in detail. The results suggested that the optimum mass fraction of starch added in anodization process was 0.1%, with which TiO₂ nanotube arrays owning good tubular structure were synthesized. The tube length and average inner diameter of nanotubes were approximately 4 μm and 30 nm, respectively. Through the characterization of TiO₂ nanotube arrays by energy dispersive spectrometer, scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, Fourier Transform Infrared (FTIR) spectroscopy, it was found that the as‐prepared nanotubes possessed well uniformed and higher photodegradation responsive than the pure TiO₂. Moreover, it was expected that the as‐prepared nanotubes exhibited good photocatalytic activity for the degradation of RhB under UV‐light irradiation, which could be ascribed to their good morphology, enhanced UV‐light absorption property and electron transmission ability during the photocatalytic reaction. In addition, the nanotubes were not significantly regenerated during the cycling runs experiment. Overall, this study could provide a principle method to synthesize TiO₂ nanotube arrays with enhanced photocatalytic activity by anodization process with starch addition for environmental purification.     

阳极氧化法制备二氧化钛纳米管及其荧光性质

室温下采用电化学阳极氧化法在NaF、Na₂SO₄和H₂SO₄的混合溶液中用化学处理后的纯Ti片表面组装了一层结构高度有序的高密度TiO₂纳米管阵列。考察了几种主要的实验参数(阳极氧化电压、温度、电解液浓度)对TiO₂纳米管阵列形貌和尺寸的影响，探讨了二次阳极氧化对纳米管形貌的改善。对TiO₂纳米管阵列进行扫描电子显微镜(SEM)和荧光(PL)分析，探讨其生长机理。结果表明，孔径随阳极氧化电压的升高而变大，温度、电解液浓度影响反应过程中电流密度的大小；二次阳极氧化得到的纳米管的有序性有所改善，孔径大小更为均一，并且发现TiO₂纳米管的荧光具有量子效应。     

Photocatalytic activities of C–N-doped TiO2 nanotube array/carbon nanorod composite

A C–N-doped TiO₂ nanotube (NT)/carbon nanorod composite is fabricated by chemical vapor deposition (CVD). Carbon nanorods are grown from the TiO₂ NTs, and partly graphitized, while TiO₂ is in the mixture of anatase and rutile. The C–N doping shifts the absorption edge of TiO₂ NTs to the visible light region; the formed carbon nanorods promote the charge carrier transfer from the TiO₂ surface to the electrolyte. Under the simulated solar light irradiation, the C–N-doped TiO₂ NTs show higher photocatalytic activity in the degradation of methyl orange (MO) than the undoped TiO₂ NTs.     

Study on mechanism of photocatalytic performance of La-doped TiO2/Ti photoelectrodes by theoretical and experimental methods

TiO₂ photoelectrodes with various nanostructures have been successfully prepared by the anodization method. The morphology, microstructure and optical properties of as-prepared photoelectrodes were studied by scanning electron microscopy (SEM), X-ray diffraction (XRD), ultraviolet/visible light diffuse reflectance spectra (UV/vis/DRS), surface photovoltage spectroscopy (SPS) and photocurrent. The electronic structure and optical properties of La doped/undoped TiO₂ photoelectrodes with different crystal structures were calculated by the density function theory. The photocatalytic and photoelectrocatalytic activities of as-prepared photoelectrodes were evaluated. The results showed that the anodization potentials played a crucial role in the surface morphology and microstructure. Both results of theoretical calculations and experimental tests demonstrated that La-doped photoelectrodes were more sensitive to light than undoped one. The difference of photoelectrodes performance was ascribed to the crystal configuration, impurity energy levels and long-range orientation moving of photogenerated carriers.     

TiO2纳米管阵列光电催化氧化处理氨氮废水

用电化学阳极氧化法制备了高度有序的钛基二氧化钛纳米管阵列薄膜。用场发射扫描电镜(FE-SEM)、X射线衍射(XRD)表征样品的形貌与晶型特征。以二氧化钛纳米管阵列为光阳极,石墨为对电极,测试了不同pH值和外加偏压条件下的光电流响应和光电催化氧化降解NH4Cl水溶液(以N计,100 mg·L-1)的效率。结果表明:所制备的TiO2纳米管阵列具有锐钛矿和金红石的混晶结构,且主要晶型为锐钛矿。光电流响应的强弱与光电催化氧化效率的高低相对应,降解氨氮废水的最佳条件为pH=11,偏压为1.0 V。     

Blue TiO2 nanotube arrays as semimetallic materials with enhanced photoelectrochemical activity towards water splitting

In the past years there has been a great interest in self-doped TiO₂ nanotubes (blue TiO₂ nanotubes) compared to undoped ones owing to their high carrier density and conductivity. In this study, blue TiO₂ nanotubes are investigated as photoanode materials for photoelectrochemical water splitting. Blue TiO₂ nanotubes were fabricated with enhanced photoresponse behavior through electrochemical cathodic polarization on undoped and annealed TiO₂ nanotubes. The annealing temperature of undoped TiO₂ nanotubes was tuned before cathodic polarization, revealing that annealing at 500 °C improved the photoresponse of the nanotubes significantly. Further optimization of the blue TiO₂ nanotubes was achieved by adjusting the cathodic polarization parameters. Blue TiO₂ nanotubes obtained at the potential of –1.4 V (vs. SCE) with a duration of 10 min exhibited twice more photocurrent response (0.39 mA cm^-2) compared to the undoped TiO₂ nanotube arrays (0.19 mA cm^-2). Oxygen vacancies formed through the cathodic polarization decreased charge recombination and enhanced charge transfer rate; therefore, a high photoelectrochemical activity under visible light irradiation could be achieved.     

Fe_2O_3/TiO_2纳米管阵列的制备及其光催化性能

在钛基体上采用阳极氧化法制备了TiO2纳米管阵列,采用化学浴方法在TiO2纳米管阵列上修饰了Fe2O3纳米颗粒。利用扫描电镜、X射线衍射和紫外可见漫反射光谱等手段对材料进行了表征,同时测试了材料的光电化学性能及其光催化降解亚甲基蓝染料废水的性能。结果表明,Fe2O3纳米颗粒的修饰将TiO2纳米管阵列的光响应拓宽至可见光区域,提高了光电流,Fe2O3/TiO2纳米管阵列的光电流是未修饰的TiO2纳米管阵列的9倍。而在光催化反应中,亚甲基蓝最高降解率可达80%,比未修饰的TiO2纳米管阵列高出30%。     

Fe2O3/TiO2纳米管阵列的制备及其光催化性能

在钛基体上采用阳极氧化法制备了TiO₂纳米管阵列,采用化学浴方法在TiO₂纳米管阵列上修饰了Fe₂O₃纳米颗粒.利用扫描电镜、X射线衍射和紫外可见漫反射光谱等手段对材料进行了表征,同时测试了材料的光电化学性能及其光催化降解亚甲基蓝染料废水的性能.结果表明,Fe₂O₃纳米颗粒的修饰将TiO₂纳米管阵列的光响应拓宽至可见光区域,提高了光电流,Fe₂O₃/TiO₂纳米管阵列的光电流是未修饰的TiO₂纳米管阵列的9倍.而在光催化反应中,亚甲基蓝最高降解率可达80%,比未修饰的TiO₂纳米管阵列高出30%.     

Synthesis of molecular imprinted polymer modified TiO2 nanotube array electrode and their photoelectrocatalytic activity

A tetracycline hydrochloride (TC) molecularly imprinted polymer (MIP) modified TiO₂ nanotube array electrode was prepared via surface molecular imprinting. Its surface was structured with surface voids and the nanotubes were open at top end with an average diameter of approximately 50 nm. The MIP-modified TiO₂ nanotube array with anatase phase was identified by XRD and a distinguishable red shift in the absorption spectrum was observed. The MIP-modified electrode also exhibited a high adsorption capacity for TC due to its high surface area providing imprinted sites. Photocurrent was generated on the MIP-modified photoanode using the simulated solar spectrum and increased with the increase of positive bias potential. Under simulated solar light irradiation, the MIP-modified TiO₂ nanotube array electrode exhibited enhanced photoelectrocatalytic (PEC) activity with the apparent first-order rate constant being 1.2-fold of that with TiO₂ nanotube array electrode. The effect of the thickness of the MIP layer on the PEC activity was also evaluated.     

浸渍-分解法制备高可见光催化活性的Bi2O3/TiO2纳米管阵列

用浸渍-分解法将Bi₂O₃纳米颗粒沉积在TiO₂纳米管壁上, 制备了Bi₂O₃/TiO₂纳米管阵列. 用电感耦合等离子体发射光谱(ICP-AES)测定了Bi₂O₃/TiO₂ 纳米管阵列的化学组分, 利用X 射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)和紫外-可见(UV-Vis)吸收光谱表征了所制备的样品. 通过在可见光下(λ>400 nm)降解甲基橙(MO)水溶液来评价样品的光催化活性. 结果表明, Bi₂O₃纳米颗粒均匀地沉积在TiO₂纳米管中. Bi₂O₃/TiO₂纳米管阵列具有比纯Bi₂O₃膜和N-TiO₂纳米管阵列高得多的可见光催化活性. Bi₂O₃/TiO₂纳米管阵列活性的增强是其强可见光吸收和Bi₂O₃与TiO₂之间形成的异质结的协同作用的结果.     

Anodized Iron Oxide Nanostructures on Different Carbon Steels for Photoelectrochemical Water Splitting

In this study, two different nanostructural iron oxide films were prepared on two kinds of carbon steels (CS) with different contents of impurities via anodization in a mixture of aqueous ammonium fluoride solution and ethylene glycol, respectively, and apply to photoelectrochemical (PEC) water splitting. After annealing, iron oxide nanotubes (NTs) was coated on surface of lower purity CS and iron oxide nanoporous (NPs) was coated on surface of higher purity CS via scanning electron microscope. X‐ray diffraction pattern shows both of samples contain a major phase of α‐Fe₂O₃ and a slight phase of Fe₃O₄. Compared with NPs, NTs behaves better absorbance ability in visible spectra range via UV‐visible absorbance spectra. From PEC response, the iron oxide NTs showed higher water splitting performance (0.10 mA/cm² at 0.4 V vs. Ag/AgCl) than NPs (0.04 mA/cm² at 0.4 V vs. Ag/AgCl) due to better absorbance, higher car‐ rier concentration and low charge transfer resistance.     

自掺杂TiO2纳米管：液相制备及光催化性能

采用水合肼（N₂H₄·H₂O）作为还原剂,在液相环境中制备了自掺杂TiO₂纳米管阵列（NTs）。利用FE-SEM、EDS、XPS、XRD、Raman、UV-Vis/NIR分光光度法以及半导体特性分析系统（Keithley 4200 SCS）分别对样品的形貌,晶体结构,光学特性以及电学性能进行了表征。结果表明：通过这种方法制备的自掺杂TiO₂NTs在带隙中引入了大量的氧空位,创造了氧空位能级,从而提高了样品的电导率,有效提高光生电子-空穴对的产生、分离和传输。此外,由于氧空位的作用,使得TiO₂NTs的带隙变窄,增强了可见光吸收能力,致使样品具有较高的光催化活性,并通过降解甲基橙溶液对样品的光催化活性进行评估。结果显示当光照150min后,自掺杂TiO₂NTs对甲基橙溶液的降解率达73%,并且这种催化剂便于回收和重复使用。