Blend membranes from cellulose/konjac glucomannan cuprammonium solution

The blend membranes were prepared from cellulose/konjac glucomannan (KGM) cuprammonium solution by coagulating with aqueous 10 wt% NaOH solution, 20°C and 40°C water, respectively. Miscibility, pore morphology, structure, water permeability and mechanical properties of the blend membranes were investigated. The complex forms of cellulose/KGM in the mixed solutions, the effect of various coagulants and the percent content of KGM (w_KGM) on the structure and properties of the blend membrane are discussed. SEM and mechanical relaxation analysis indicate that the blend membranes are miscible in the range of 0–30 wt% of w_KGM. When w_KGM was smaller than 20 wt%, the tensil strength of the blend membrane coagulated by alkali aqueous solution was enhanced, corresponding to homogeneous structure and small pore size. However, blend membranes having a larger pore size (366 nm by SEM) and water permeability (560 ml/m² h mmHg) were obtained by coagulating the cellulose/KGM (70:30) cuprammonium solution with 40°C water, where ca. 20% of KGM as pore former were removed from the membrane.     

再生纤维素／聚乙烯醇共混膜的研究

由纤维素铜氨溶液与不同体积比（１－１０％）的聚乙烯醇（ＰＶＡ）水溶液共混制备了一系列再生纤维素共混膜．扫描电镜结果表明ＰＶＡ含量大于８％时，该共混膜产生明显相分离．当ＰＶＡ低于５％时，共混膜相容性较好．膜的结晶度，抗张强度，直角撕裂强度，断裂伸长及耐热性均优于单独用钢氨液制备的再生纤维素膜．此外，用流动速率法和超滤法测定了膜的孔径，渗透性及纯水通量，结果表明共混膜的孔性没有明显变化．本文得出：再生纤维素与５％ＰＶＡ共混能改善力学性能，并且能保持其生物降解性．     

Structure and properties of blend membranes prepared from cellulose and alginate in NaOH/urea aqueous solution

Regenerated cellulose (RC)/alginic acid (AL) blend membranes were satisfactorily prepared from 6 wt % NaOH/4 wt % urea aqueous solution by coagulating with 5 wt % CaCl₂ aqueous solution, and then treated with 3 wt % HCl. Morphology, crystallinity, mechanical properties, and thermal stability of the membranes were investigated by scanning electron microscopy (SEM), IR and UV spectroscopes, X‐ray diffraction, tensile tests, and thermogravimetric analysis (TGA). The RC/AL blends were miscible in all weight ratios of cellulose to alginate. The membranes have homogeneous mesh structures, and the mesh sizes of the blend membranes (200–2000 nm) significantly increased with increasing alginate content. The crystalline state of the AL membrane prepared from 6 wt % NaOH/4 wt % urea aqueous solution was broken completely, and the crystallinity of the blend membranes decreased with an increase of AL. Comparing with AL membranes, the tensile strength and breaking elongation of the blend membranes were obviously improved in dry and wet states. Therefore, the RC/AL blends offer a promising way of alginate as separate and functional materials used in the wet state. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 451–458, 2001     

Structure and properties of the regenerated cellulose membranes prepared from cellulose carbamate in NaOH/ZnO aqueous solution

Regenerated cellulose (RC) membranes were prepared from cellulose carbamate—NaOH/ZnO aqueous solutions by coagulating with H₂SO₄ solution. Structure, morphology and properties of the membranes were investigated by using scanning electron micrograph (SEM), X-ray diffraction, Fourier transform infrared spectroscopy, flow rate method, and tensile testing. The results from SEM and water permeability revealed that the pore size and water permeability of the membranes in wet state changed drastically as a function of the concentration of H₂SO₄ and coagulation temperature, whereas they hardly changed with the coagulation time. RC membranes coagulated with the relatively dilute H₂SO₄ solution at relatively low temperature exhibited better mechanical properties. This work provided a promising way to prepare cellulose membranes with different pore sizes and good physical properties.     

Dissolution and regeneration of cellulose in NaOH/thiourea aqueous solution

A novel cellulose solvent, 1.5 M NaOH/0.65 M thiourea aqueous solution, was used to dissolve cotton linters having a molecular weight of 10.1 × 10⁴ to prepare cellulose solution. Regenerated cellulose (RC) films were obtained from the cellulose solution by coagulating with sulfuric acid (H₂SO₄) aqueous solution with a concentration from 2 to 30 wt %. Solubility of cellulose, structure, and mechanical properties of the RC films were examined by infrared spectroscopy, X‐ray diffraction, scanning electron microscopy, ¹³C NMR, and tensile tests. ¹³C NMR analysis indicated that the novel solvent of cellulose is a nonderivative aqueous solution system. The presence of thiourea enhanced significantly the solubility of cellulose in NaOH aqueous solution and reduced the formation of cellulose gel; as a result, thiourea prevented the association between cellulose molecules, leading to the solvation of cellulose. The RC film obtained by coagulating with 5 wt % H₂SO₄ aqueous solution for 5 min exhibited higher mechanical properties than that with other H₂SO₄ concentrations and a homogenous porous structure with a mean pore size of 186 nm for free surface in the wet state. The RC film plasticized with 10% glycerin for 5 min had a tensile strength of 107 MPa and breaking elongation of 10%, and about 1% glycerin in the RC film plays an important role in the enhancement of the mechanical properties. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1521–1529, 2002     

Morphology and permeability of cellulose/chitin blend membranes

A series of biodegradable cellulose/chitin blend membranes were successfully prepared from blend solution of cellulose and chitin in 9.5 wt% NaOH/4.5 wt% thiourea aqueous solution coagulating with 5.0 wt% (NH₄)₂SO₄. The influence of chitin content on the morphology and structure of the membranes was studied by scanning electron microscopy, environmental scanning electron microscopy and wide-angle X-ray diffractometry, as well as Fourier transform infrared spectroscopy. Using double-cell method and solution depletion method, the permeability and partition coefficients of three model drugs (ceftazidine, cefazolin sodium, and thiourea) were determined in phosphate buffer solution to clarify the diffusion mechanism governing transport of solutes in these membranes. Diffusion coefficients were calculated from the permeability and partition coefficients in terms of Fick's law. The effects of the chitin content, pH, ionic strength, molecular size and temperature on the drug diffusion were also studied. Our results revealed that all of the membranes had a porous-like structure. The introduction of chitin exhibited great influence on the morphology and crystal structure of the blend membranes, resulting in a significant different permeability. For the first time, a dual diffusion mechanism with some hindrance of molecular diffusion via polymer obstruction was employed to explain the transport of drugs in the membranes.     

CHARACTERIZATION OF REGENERATED CELLULOSE MEMBRANES HYDROLYZED FROM CELLULOSE ACETATE

A series of cellulose acetate membranes were prepared by using formamide as additive, and then were hydrolyzedin 4 wt% aqueous NaOH solution for 8 h to obtain regenerated cellulose membranes. The dependence of degree ofsubstitution, structure, porous properties, solubility and thermal stability on hydrolysis time was studied by chemical titration,Fourier transform infrared spectroscopy, scanning electron microscopy, wide-angle X-ray diffraction, and differentialscanning calorimetry, respectively. The results indicated that the pore size of the regenerated cellulose membranes wasslightly smaller than that of cellulose acetate membrane, while solvent-resistance, crystallinity and thermostability weresignificantly improved. This work provides a simple way to prepare the porous cellulose membranes, which not only kept thegood pore characteristics of cellulose acetate membranes, but also possessed solvent-resistance, high crystallinity andthermostability. Therefore, the application range ofcellulose acetate membranes can be expanded.     

Properties of cellulose films prepared from NaOH/urea/zincate aqueous solution at low temperature

Cellulose films were successfully prepared from NaOH/urea/zincate aqueous solution pre-cooled to −13 °C by coagulating with 5% H₂SO₄. The cellulose solution and regenerated cellulose films were characterized with dynamic rheology, ultraviolet–visible spectroscope, scanning electron microscopy, wide angle X-ray diffraction, Fourier transform infrared (FT-IR) spectrometer, thermogravimetry and tensile testing. The results indicated that at higher temperature (above 65 °C) or lower temperature (below −10 °C) or for longer storage time, gels could form in the cellulose dope. However, the cellulose solution remained a liquid state for a long time at 0–10 °C. Moreover, there was an irreversible gelation in the cellulose solution system. The films with cellulose II exhibited better optical transmittance, high thermal stability and tensile strength than that prepared by NaOH/urea aqueous solution without zincate. Therefore, the addition of zincate in the NaOH/urea aqueous system could enhance the cellulose solubility and improve the structure and properties of the regenerated cellulose films.     

Influence of coagulation temperature on pore size and properties of cellulose membranes prepared from NaOH–urea aqueous solution

The morphology and structure of the regenerated cellulose membranes prepared from its NaOH–urea aqueous solution by coagulating with 5 wt% H₂SO₄–10 wt% Na₂SO₄ aqueous solution with different temperatures and times were investigated. The pore size, water permeability and physical properties of the membranes were measured with scanning electron micrograph (SEM), wide X-ray diffraction (WXRD), Fourier transfer infrared spectroscopy (FTIR), flow rate method, and tensile testing. The SEM observation revealed that the structure and pore size of the membranes changed drastically as a function of the coagulation temperature. The membranes coagulated at lower temperatures tended to form the relatively small pore size than those at higher temperatures. On the contrary, the membranes coagulated at different times exhibited similar pore size. Interestingly, the mean pore size and water permeability of the membranes increased from 110 nm with standard deviation (SD) of 25 nm and 12 ml h⁻¹ m⁻² mmHg⁻¹ respectively to 1,230 nm with SD of 180 nm and 43 ml h⁻¹ m⁻² mmHg⁻¹ with an increase in coagulation temperature from 10 to 60°C. However, the membranes regenerated below 20°C exhibited the dense structure as well as good tensile strength and elongation at break. The result from FTIR and ultraviolet-visible (UV-vis) spectroscopy indicated that the relatively strong intermolecular hydrogen bonds exist in the cellulose membranes prepared at lower coagulation temperatures. This work provided a promising way to prepare cellulose materials with different pore sizes and physical properties by controlling the coagulation temperature.     

Conformation transition of silk fibroin induced by blending chitosan

The conformation of silk fibroin in silk fibroin/chitosan (SF/CS) blend membrane was analyzed by infrared spectrum, X-ray diffractometry, and Raman spectrum. The results demonstrated that the SF could show β-sheet conformation when the SF content in blend membranes was 10% (w/w) and 60–80% (w/w), while the pure SF membrane showed random coil conformation. A mechanism of the conformation transition was suggested in that the SF chain could use the rigid CS chain as a mold plate to stretch itself to form a β-sheet structure according to the strong hydrogen bond between CS and SF. Therefore, a new concept, named “Polymer-Induced Conformation Transition,” was proposed. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2293–2296, 1997     

Miscibility and biodegradability of silk fibroin/carboxymethyl chitin blend films

Blend films of silk fibroin and carboxymethyl chitin were prepared by solution casting using water as a cosolvent. The blend films were subjected to post-treatment with an aqueous methanol solution to induce beta-sheet formation of silk fibroin. The miscibility of the blend films both before and after methanol treatments was investigated in terms of chemical interactions, morphologies, thermal properties, and crystal structures by using FTIR spectroscopy, SEM, DSC, and XRD. The results indicate that the blend between silk fibroin and CM-chitin was semi-miscible because only the amorphous parts of the polymers were compatible with each other. The enzymatic degradation showed that the incorporation of CM-chitin enhanced biodegradability and swelling ability of silk fibroin.     

Microfiltration performance of regenerated cellulose membrane prepared at low temperature for wastewater treatment

A series of regenerated cellulose membranes with pore diameters ranging from 21 to 52 nm have been prepared by dissolving cellulose in 5 wt% LiOH/12 wt% urea aqueous solution re-cooled to −12 °C. The influences of cellulose concentration on the structure, pore size, and the mechanical properties of the membrane were studied by using Wide angle X-ray diffraction, scanning electron micrography and tensile testing. Their pore size, water permeability, equilibrium-swelling ratio and fouling behaviors of the cellulose membranes were characterized. The water-soluble synthetic and natural polymers as organic matter were used to evaluate the microfiltration performance of the regenerated cellulose membrane for wastewater treatment in aqueous system. The results revealed that the organic matter with molecular weight more than 20 kDa effected significantly on the membrane pore density, and reducing factor a _2, whereas that having molecular weight less than 20 kDa exhibited a little influence on the membrane pore size reducing factor a ₁. Furthermore, a simple model to illustrate of microfiltration process of the RC membrane for wastewater treatment was proposed.     

聚醚砜/纤维素晶体共混膜材料及其超滤性能

聚醚砜与纤维素晶体等共混成铸膜液,采用浸没沉淀相转化法制备聚醚砜/纤维素晶体共混膜材料.通过超滤装置检测复合膜的水通量、截留率、平均孔径、孔隙率、抗污染性等超滤性能,从而讨论了纤维素晶体含量对共混膜超滤性能的影响.采用抗张测试机、热重分析仪(TGA)、原子力显微镜(AFM)对共混膜的力学性能、热稳定性能、形貌结构进行表征.结果表明,随着纤维素晶体的含量的增加,共混膜的纯水通量先升高后有所降低,截留率均保持在91%～95%,抗张强度、断裂伸长率先增大后有所下降,抗污染性较纯聚醚砜膜显著提高.当纤维素晶体质量分数为1%时,纯水通量达到最大为813.3L·m-2·h-1,孔隙率为88.8%,平均孔径达为70.9nm,抗张强度为7.25MPa,断裂伸长率为11.6%,平均污染度FR值为22.0%,衰减系数m值为35.8%.共混膜具有由纤维素晶体、聚醚砜热降解分别引起的两个失重阶段.共混膜为典型非对称膜结构,表皮层较为致密,多孔支撑层孔径较大.     

Preparation of ultrafiltration membranes of HCEC and CTA blend, and studies of resistance to microbiological degradation and other properties

Blends of high cyanoethylated cellulose (HCEC) (D_s = 2.5) and cellulose triacetate (CTA) (D_s = 2.8) were prepared for evaluation as ultrafiltration membranes. The rejection R_a and water permeability (P_w) of these membranes with respect to bovine serum albumin (BSA), were measured with the variations in composition and conditions of preparation. It was possible to define the reaction conditions and compositions that offered optimum performance with respect to R_a and J_w, and resistance to microbial degradation as well as acid and alkali hydrolysis. The morphology of membrane thereby obtained was characterized by scanning electron microscopy (SEM). The UF membrane cast from a solution of 1,4-dioxane: 12.5 g, acetone: 12.5 g, HCEC: 1.5 g, CTA: 3 g and PEG (MW = 1000): 10.5 g showed the optimum performance of P_w = 10 × 10⁻¹⁰ m³/(m² s Pa), BSA Rejection (R_a) = 99%, (J_w = 17.3 m³/(m² day) at ΔP = 0.2 MPa) and a molecular weight cut off at 4.9 × 10⁴ Da. After immersion in mud for 170 days, reduction of R_a was only 8% for UF membrane containing 10 wt% HCEC blend, and was not observed to be obviously different from the membrane containing more than 30 wt% HCEC blend. The higher permeability and rejection of blend membrane may be attributable to the network structure formed via CTA and HCEC penetration.     

CELLULOSE ACETATE AND EPOXY RESIN BLEND ULTRAFILTRATION MEMBRANES: REPARATION,CHARACTERIZATION, AND APPLICATION

ABSTRACT

Membranes based on cellulose acetate used in ultrafiltration applications lack good, chemical, mechanical and thermal resistance. In order to prepare membranes with improved properties, modification of cellulose acetate with epoxy resin through solution blending was attempted. In the present work, the membrane casting solutions with different polymer blend compositions of cellulose acetate and diglycidyl ether of bisphenol-A (DGEBA) were prepared at 30±2°C. The maximum percent compatibility of the two polymers, cellulose acetate and diglycidyl ether of bisphenol-A, was estimated to be 60/40%. Ultrafiltration blend membranes based on various blend compositions were prepared, characterized in terms of compaction, pure water flux, water content, membrane hydraulic resistance and molecular weight cut-off. The application of these membranes, in rejection of proteins of various molecular weights, are discussed.     

Cellulose acetate and polyetherimide blend ultrafiltration membranes: II. Effect of additive

Ultrafiltration membranes are largely applied in the separation of heavy metal ion and macromolecular solutes from aqueous streams. Studies are presented on ultrafiltration blend membranes, based on cellulose acetate (CA) and polyetherimide (PEI) in various blend compositions. Polyethylene glycol (PEG 600) was employed as a non‐solvent additive in various concentrations to the casting solution to improve the ultrafiltration performance of the resulting membranes. The blend membranes prepared were characterized in terms of compaction time, pure water flux (PWF), water content, membrane resistance, and scanning electron microscopy (SEM). The molecular weight cut‐off (MWCO) obtained from the protein separation studies is also reported. Applications of these membranes for separating toxic metal ions from aqueous streams are discussed. Copyright © 2007 John Wiley & Sons, Ltd.     

Structure and pH‐sensitive properties of poly (vinylidene fluoride) membrane changed by blending poly (acrylic acid) microgels

pH‐sensitive poly (vinylidene fluoride) (PVDF)/poly (acrylic acid) (PAA) microgels membranes are prepared by phase inversion of the N, N‐dimethylformamide solution containing PAA microgels and PVDF in aqueous solution. The composition and structure of the blend membrane are investigated by Fourier transform infrared spectra, X‐ray photoelectron spectroscopy measurements, thermo gravimetric analysis, field‐emission scanning electron microscope and atomic force microscope. The results indicate the surface and cross section of the blend membranes have a porous structure with PAA microgels immobilized inside the pore and on the membrane surface. The blend PVDF membranes exhibit pH‐sensitive water flux, with the most drastic change in permeability observed between pH 3.7 and 6.3. The blend membranes are fouled by bovine serum albumin, and their antifouling property is enhanced by increasing PAA microgels, mainly derived from the improved hydrophilic property. Copyright © 2013 John Wiley & Sons, Ltd.     

A graphene oxide facilitated a highly porous and effective antibacterial regenerated cellulose membrane containing stabilized silver nanoparticles

Regenerated nanocomposite cellulose membranes embedded with silver nanoparticles (AgNP) and AgNP-graphene oxide (AgGO) were prepared in this study. The as-synthesized AgNP and AgGO were added respectively to a cellulose solution that was prepared by dissolving cellulose in a precooled NaOH/urea (NU) solvent. The solution mixtures were further regenerated into nanocomposite membranes through coagulation in an acidic solution. UV-Vis and TEM results revealed the improved stability of the AgGO compared to that of the AgNP in NU solutions. As revealed by FESEM, the AgGO nanocomposite membrane possessed a more porous structure than a membrane containing AgNP. Antibacterial tests demonstrated that the cellulose membrane of AgGO inhibited the growth of both Staphylococcus aureus and Escherichia coli more effectively than the AgNP nanocomposite membrane, with a lower concentration of AgGO. This work provides a proven and effective method to prepare novel functional cellulose membranes with antibacterial properties, thus broadening the applications of cellulose.     

羟丙基甲基纤维素诱导丝素蛋白的构象转变

制备了羟丙基甲基纤维素 (HPMC)和丝素蛋白 (SF)的共混膜 ,用FTIR ,XRD和DSC方法对共混膜的结构进行了表征 ,讨论了HPMC对SF的构象转变作用 ,结果表明 ,HPMC能够有效的诱导SF的构象转变 ,HPMC的比例是影响SF的构象转变程度的重要因素 .当混入 3%～ 10 %HPMC时 ,SF的构象存在由无规线团或SilkI向SilkII(β 折叠 )的转变 ,当加入 7%HPMC时 ,β 折叠构象的比例最大 .从红外分析可知 ,构象转变是由于适量的HPMC与SF混合形成了二者之间的分子间氢键所致 .对不同比例的共混膜测定其在水中的溶出率 ,结果显示当HPMC的比例为 7%时SF几乎不溶于水     

Bending properties and cell wall structure of alkali-treated wood

Bending tests and X-ray diffraction studies were conducted on oven-dried wood samples (Picea jezoensis Carr.) treated with various concentrations of aqueous NaOH solution to investigate the influence of alkali treatment on the longitudinal contraction, bending properties, and cellulose structure. The length of the wood samples decreased and the density increased at NaOH concentrations greater than 10%. The Young’s modulus and the specific Young’s modulus decreased and the strain at yield increased for the same concentration range. However, the stress at yield was almost constant for all concentration ranges. X-ray diffraction analysis showed that lattice transformation from cellulose I to cellulose II did not occur during alkali treatment and the crystallinity index decreased at NaOH concentrations greater than 10%. The crystallinity index was linearly correlated with the changes in longitudinal contraction and the bending properties, which indicates that the increase in the proportion of amorphous components of the cellulose influences the longitudinal contraction and the bending properties of wood samples during alkali treatment.