臭氧氧化法合成全羟基葫芦[6]脲

葫芦脲(CB[n])的直接衍生化一直是一项难题。本文用臭氧氧化法将CB[6]衍生化,合成全羟基葫芦[6]脲((OH)12CB[6])。CB[6]与O3在20℃下反应 22h,生成(OH)12CB[6]的产率为44%,并探究了丙酮扩散法、柱层析法和DMSO提纯法三种去除无机盐的方法的可行性。臭氧由电解水制得,成本低,没有二次污染,且臭氧氧化能力强,在室温下即可氧化葫芦脲。本文为合成全羟基葫芦脲提供了新的方法。     

基于改性瓜环的新型固相微萃取搅拌棒的制备及其在检测环境水样中布洛芬含量方面的应用

通过凝胶-溶胶法制备了两种新型PDMS/Hydroxylated CB[n](n=5,6)固相微萃取搅拌棒,结合高效液相色谱法测定环境水中布洛芬的含量。考察了萃取时间,萃取温度,解吸时间,盐离子强度和介质p H等实验条件对萃取效率的影响。控制溶液pH=2.0,C_(NaCl)=0.15 g·m L~(-1),在25℃下搅拌萃取30 min,用甲醇超声解吸7 min萃取效果最佳。其中PDMS/Hydroxylated CB[6]涂层的效果更好,其富集倍数可达19倍。该方法在0.05~10μg·m L~(-1)的布洛芬质量浓度范围内呈现较好的线性关系,相关系数为0.9993,检出限为1.2 ng·m L~(-1),RSD为3.1%,表明该方法具有较好的重复性和可靠性。     

葫芦脲的分解氧化研究

葫芦脲是高度对称的刚性分子,在试图改进Kim等氧化制取羟基葫芦脲的过程中发现,葫芦[6]脲(CB[6])在多种过硫酸盐(过硫酸钾、过硫酸钠、过硫酸胺)的氧化下,除了可以获得羟基葫芦脲外,还可以得到进一步分解产物草酸.研究表明,CB[n](n=5,7,8)及其羟基葫芦脲也存在类似的现象.这是国内外首次发现葫芦脲在进行腰位C—H键羟基化的同时,还可以进一步氧化形成草酸.     

新型固相微萃取涂层的研究进展*

作为一种样品前处理方法的固相微萃取(solid phase microextraction, SPME)技术,具有操作方便,快速,灵敏和无需大量有机溶剂的优点,因此在分离分析方面得到了广泛的应用。涂层是SPME技术的核心部分,其性能决定了SPME的性能和应用范围,因此发展新型涂层一直是SPME研究和应用工作的重点。近年来随着涂层材料制备技术的发展,出现了一些新型涂层。这些新型涂层的出现进一步拓宽SPME技术的应用范围。本文综述了近三年来SPME涂层的研究进展,并着重介绍新型涂层的制备方法和性质。     

一种新型羟基葫芦[6]脲气相色谱固定相性能的研究

本文首次成功地制备和利用羟基葫芦[6]脲((HO)12CB[6])作填充柱气相色谱固定相。研究表明,羟基葫芦[6]脲固定相(PSP)具有较宽的操作柱温、高度的化学和热稳定性,对多种类型的化合物展示较高的色谱分离选择性,这包括烷烃、芳烃、醇类、酯类、酮类和胺类等多种化合物。新柱对一些二取代苯环芳族位置异构体有较强的分离能力。实验发现,羟基葫芦[6]脲固定相对日用花露水中复杂的挥发性成分有高效快速分离能力。同时,初步探讨了新固定相的色谱分离机理,发现羟基葫芦[6]脲对溶质的部分包结作用,而不是完全包结作用,有利于提高其色谱分离选择性和柱效。此外,在极速程序升温色谱中,该固定相低流失基线漂移小,有利于实现宽沸点范围复杂样品的快速气相色谱分离分析。     

葫芦[n]脲超分子水凝胶的研究进展

超分子化学的发展一直是众多研究者所关注的一大热点,葫芦[n]脲作为第四代大环主体分子,拓宽了超分子化学领域的发展。水凝胶是一种具有可拉伸性、生物相容性、环境响应性等多种优异性能的软材料。人们充分利用葫芦[n]脲优异的分子识别能力和配位能力,研究出了一系列具有特殊功能的超分子水凝胶材料。本文在结合葫芦[n]脲特点的基础上,着重论述了葫芦[n]脲水凝胶在(刺激响应性、粘附性、自愈合性)功能性材料、(药物传递、伤口敷料、仿生)生物医学材料、超分子发光材料等领域的研究前沿和动态,并且对葫芦[n]脲水凝胶的主要设计思路进行了讨论。最后,针对当前存在的问题以及未来可能的发展方向对葫芦[n]脲水凝胶的研究前景作出了展望。     

用于固相微萃取的乙烯基开链冠醚复合涂层的研制

固相微萃取 (SPME)是一种新型的样品预处理技术 [1] ,其核心是 SPME装置中萃取头上的固相涂层 .目前商用 SPME涂层的种类较少 ,热稳定性较差 (推荐使用温度 2 0 0～ 2 80℃ ) ,使用寿命较短(40～ 1 0 0次 ) ,价格偏高 ,限制了其推广应用 .因此发展高选择性、高稳定性和高效的固     

葫芦[n]脲应用研究进展

葫芦[n]脲(CB[n]简称CB)及其衍生物是由n个甘脲单元连接而成的大环主体分子,因其特殊的结构和分子识别性能,而受到广泛关注。以共价或非共价的方法,葫芦[n]脲可以构筑出各种功能的纳米超分子组装体,而且还可以赋予超分子组装体很多新颖的物理化学特性,使其在反应容器、表面活性剂、载体、囊泡、分子开关、离子选择性电极等方面展现出极大的应用潜力。本文综述了近年来基于葫芦[n]脲纳米超分子组装体的构筑及应用研究进展,并展望了葫芦[n]脲化合物的发展前景,以期对于进一步构筑具有特定结构和功能的葫芦[n]脲纳米超分子组装体的研究起到积极的促进作用。     

荧光光谱法研究葫芦[7]脲与6-巯嘌呤和腺嘌呤的包结作用

采用荧光光谱法分别研究了葫芦[7]脲(CB[7])对6-巯嘌呤(6-MP)和腺嘌呤(ADP)的包结作用。实验考察了时间、pH值以及温度对荧光强度和包结作用的影响,利用Benesi-Hildebrand方程分别计算出6-MP和ADP与CB[7]的包结常数。结果表明:酸度对体系的包结有明显的影响。在pH值为8.0和2.0左右时,6-MP和ADP分别具有稳定和最佳激发和发射波长,随着CB[7]浓度的增大,体系的荧光强度都有明显增强,包结作用迅速(小于5 min)。实验得出CB[7]与6-MP和ADP的包结比均为1∶1,在298 K时的包结常数分别为3.6797×102L·mol-1和2.2033×102L·mol-1。通过热力学参数的变化,探讨了维系包结物稳定性的主要作用力。CB[7]是葫芦脲家族中水溶性最强的主体分子,作为一种安全低毒的药物载体极具潜力。     

固相微萃取/气相色谱-质谱联用技术测定燕窝中挥发性成分

该文以印尼产的燕窝为材料,使用固相微萃取(SPME)技术萃取燕窝中挥发性成分并以气相色谱-质谱(GC-MS)联用仪进行测定。考察了萃取头类型、萃取温度、萃取时间和解吸时间对固相微萃取(SPME)在燕窝挥发性成分测定中的影响。结果表明:以65μm聚二甲基硅氧烷/二乙烯基苯(PDMS/DVB)萃取头、在60℃下萃取60 min,解吸2 min的条件下,SPME/GC-MS技术可检出燕窝中挥发性成分醇、烃、醛、酯、醚类等化合物共82种。该方法具有操作简便、快速、重复性好和灵敏度高的特点,适用于燕窝中挥发性成分的测定。     

Ultra‐rapid non‐equilibrium solid‐phase microextraction at elevated temperatures and direct coupling to mass spectrometry for the analysis of lidocaine in urine

Solid‐phase microextraction (SPME) has been directly coupled to an ion‐trap mass spectrometer (MS) for the determination of the model compound lidocaine in urine, hereby applying MS/MS [fragmentation of [M + H]⁺ (m/z 235) to a fragment with m/z 86]. The throughput of samples has been increased using non‐equilibrium SPME with polydimethylsiloxane (PDMS) fibers. The effect of temperature on the sorption and the desorption was studied. Elevated temperatures during sorption (65°C) and desorption (55°C) had a considerable influence on the speed of the extraction. The desorption was carried out with a home‐made desorption chamber allowing thermostating. Only 1 min sorption and 1 min desorption were performed, after which MS detection took place, resulting in a total analysis time of 3 min. Detection limits below 1 ng/mL could be obtained despite yields of only 2.1 and 1.5% for a 100‐ and a 30‐μm PDMS‐coated fiber, respectively. Furthermore, the determination of lidocaine in urine had acceptable reproducibilities, i.e., relative standard deviations (RSDs) below 10%. A limit of quantitation (RSD < 15%) of about 1 ng/mL was obtained. No extra wash step of the extraction fiber was required after desorption if a 30‐μm coating was used, whereas not all the analyte was desorbed from the 100‐μm coating in a single desorption. Therefore, the SPME‐MS/MS system with a 30‐μm PDMS‐coated fiber for rapid non‐equilibrium SPME at elevated temperatures has interesting potential for high‐throughput analysis of biological samples.     

Optimization of a sensitive method for the determination of nitro musk fragrances in waters by solid-phase microextraction and gas chromatography with micro electron capture detection using factorial experimental design

A solid-phase microextraction method (SPME) followed by gas chromatography with micro electron capture detection for determining trace levels of nitro musk fragrances in residual waters was optimized. Four nitro musks, musk xylene, musk moskene, musk tibetene and musk ketone, were selected for the optimization of the method. Factors affecting the extraction process were studied using a multivariate approach. Two extraction modes (direct SPME and headspace SPME) were tried at different extraction temperatures using two fiber coatings [Carboxen–polydimethylsiloxane (CAR/PDMS) and polydimethylsiloxane–divinylbenzene (PDMS/DVB)] selected among five commercial tested fibers. Sample agitation and the salting-out effect were also factors studied. The main effects and interactions between the factors were studied for all the target compounds. An extraction temperature of 100 °C and sampling the headspace over the sample, using either CAR/PDMS or PDMS/DVB as fiber coatings, were found to be the experimental conditions that led to a more effective extraction. High sensitivity, with detection limits in the low nanogram per liter range, and good linearity and repeatability were achieved for all nitro musks. Since the method proposed performed well for real samples, it was applied to different water samples, including wastewater and sewage, in which some of the target compounds (musk xylene and musk ketone) were detected and quantified. Figure Stardardized Pareto charts for the main effects and interactions     

Determination of phthalates in water using fiber introduction mass spectrometry

Fiber introduction mass spectrometry (FIMS)-a direct coupling of SPME and MS-using selective ion monitoring (SIM) was used to detect and quantify dimethylphthalate (DMP), diethylphthalate (DEP) and dipropylphthalate (DPP) in mineral water. In FIMS, a chromatographic silicone septum is the only barrier between ambient and the high-vacuum mass spectrometer, permitting direct introduction of the SPME fiber into the ionization region of the equipment. After their thermal desorption and ionization and dissociation, the extracted phthalates are detected and quantitated by MS. Three types of SPME fibers were screened for best analyte sorption/desorption behaviors: 100 microm polydimethylsiloxane (PDMS), 65 microm polydimethylsiloxane/divinylbenzene (PDMS/DVB) and 65 microm Carbowax/divinylbenzene (CW/DVB). The PDMS/DVB and CW/DVB fibers were then evaluated for precision, and quantitative figures of merit were assessed for extractions using the PDMS/DVB fiber, which displayed the best overall performance. FIMS with the PDMS/DVB fiber allows simple extraction and MS detection and quantitation of DMP in water with good linearity and precision, and at concentrations as low as 3.6 microg L(-1). The LD and LQ of FIMS are below the maximum phthalate concentration allowed by the USEPA for drinking water (6 microg L(-1)).     

Flavour analysis of Greek white wine by solid-phase microextraction-capillary gas chromatography-mass spectrometry

Solid-phase microextraction (SPME) was optimised for the qualitative determination of the volatile flavour compounds responsible for the aroma of Greek Boutari wine. Several factors influencing the equilibrium of the aroma compounds between the sample and the SPME fiber were taken into account, including the extraction time, the extraction temperature, the sampling mode (headspace and direct immersion or liquid SPME), and the presence of salt. Four different SPME fibers were used in this study. namely poly(dimethylsiloxane) (PDMS), poly(acrylate), carbowax-divinylbenzene and divinylbenzene-carboxen on poly(dimethylsiloxane). The best results were obtained using the PDMS fiber during headspace extraction at 25 degrees C for 30 min after saturating the samples with salt. The optimised SPME method was then applied to investigate the qualitative aroma composition of three other Greek wines, namely Zitsa, Limnos and Filoni.     

Optimization of headspace solid phase microextraction for gas chromatography/mass spectrometry analysis of widely different volatility and polarity terpenoids in olibanum

The aim of this study was the optimization of headspace SPME conditions for trapping diterpenes present in frankincense (olibanum). Diterpenes like cembrenes or incensole and its derivatives are characteristic of olibanum. So in order to detect by SPME the occurrence of olibanum in archeological objects, it appears essential to have the best extraction conditions for these diterpenes that will be in very small quantities. Both sampling time and extraction temperature were studied and five fiber coatings were tested: polydimethylsiloxane (PDMS), polydimethylsiloxane/divinylbenzene (PDMS/DVB), carboxen/polydimethylsiloxane (CAR/PDMS), divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) and carbowax/divinylbenzene (CW/DVB). The PDMS/DVB fiber was found to be the most efficient for trapping olibanum characteristic diterpenes, with a sampling time of 1 h and a sampling temperature of 80 degrees C.     

Solid Phase Microextraction Fibers Coated with Sol-gel Aminopropylsilica/polydimethylsiloxane: Development and Its Application to Screening of Beer Headspace

The preparation and applicability of solid phase microextraction (SPME) fibers coated with a sol-gel organically modified silica based on 3-aminopropyltrimethoxysilane and polydimethylsiloxane (APTMS/PDMS) are described here. Micrographs of the coated fibers revealed a rugous surface; the thickness of the coating was estimated to be less than 30 microm. The APTMS/PDMS fibers were tested with synthetic samples and compared to commercial fibers for headspace SPME analysis of beer. Extraction and desorption using the APTMS/PDMS fibers were faster, which is typical for sol-gel SPME fibers. For polar and semi-polar compounds on beer headspace, the extraction efficiencies of the APTMS/PDMS fiber were superior to those of conventional fibers. The APTMS/PDMS fiber was found to be capable of extracting a broad range of analytes, including highly polar acidic species such as organic acids.     

Optimization of Modern Analytical SPME and SPDE Methods for Determination of <Emphasis Type="Italic">Trans</Emphasis>-2-nonenal in Barley,Malt and Beer

Trans-2-nonenal is an aldehyde contributing to an unpleasant off-flavor and odor of rancid butter in stored beer. The automated solid-phase microextraction technique (SPME) coupled with gas chromatography (GC) and solid-phase dynamic extraction (SPDE) coupled with gas chromatography were optimized and introduced to determine trans-2-nonenal in barley, malt and beer. Five types of SPME fibers coated with different stationary phases (100 μm PDMS, 65 μm PDMS/DVB, 85 μm CAR/PDMS, 50/30 μm DVB/CAR/PDMS, 85 μm PA) and two needles (PDMS, PDMS/AC) were compared and tested for their efficiencies in the headspace (HS) SPME and SPDE determination of trans-2-nonenal in barley, malt and beer. The highest extraction efficiency of HS-SPME was achieved with the PDMS/DVB fiber, and addition of 1.5 g of NaCl, extraction time was 20 min at 60 °C. The highest extraction efficiency of HS-SPDE was obtained with the PDMS needle, 15 extraction strokes at 60 °C and addition of 1.5 g of NaCl. Trans-2-nonenal was identified with the method of HS-SPME coupled gas chromatography-mass spectrometry (GC–MS); the samples were analyzed using the HS-SPME-GC-coupled gas chromatography-flame ionization detector (GC-FID) technique.     

Solid-phase microextraction of polychlorinated biphenyls

The extraction and analysis of 21 polychlorinated biphenyls (PCBs) ranging from di- to decachlorobiphenyls in ocean, wetland and leachate water samples were achieved using solid-phase microextraction (SPME) with a 100-μm poly(dimethylsiloxane) (PDMS) fiber and gas chromatography–electron-capture detection (GC–ECD). Severe carryover between samples (e.g., 20%) occurs on both stir bars and the SPME fibers demonstrating that it is important to use a new stir bar for each sample, as well as to perform SPME–GC blanks between samples to avoid quantitative errors. The equilibrium partitioning coefficients of individual PCB congeners between PDMS and water were found to be surprisingly different compared to their octanol–water partitioning coefficient (K_ow), demonstrating that K_ow cannot be used to estimate the partitioning behavior of PCBs in the SPME process. Using a 15-min SPME extraction, SPME analysis with GC–ECD was linear (r²≥0.97) from 5 pg/ml to the solubility limit of each congener. Concentrations in water samples obtained by 15-min SPME extractions compared favorably with those obtained by toluene extractions, demonstrating that SPME combined with GC is a useful technique for the rapid determination of PCBs in water samples.     

Attachment of nickel hexacyanoferrates nanoparticles on carbon nanotubes: preparation, characterization and bioapplication

Anilinemethyltriethoxysilane (AMTEOS) was first used as precursor as well as selective stationary phase to prepare the sol-gel derived anilinemethyltriethoxysilane/polydimethylsiloxane (AMTEOS/PDMS) solid-phase microextraction (SPME) fibers. The novel SPME fiber exhibits high extraction efficiency, good thermal stability and long lifetime compared with commercial SPME coatings. In addition, the phenyl groups in the porous layer can exhibit π-π interactions with aromatic compounds, such as monocyclic aromatic hydrocarbons (MAHs) and polycyclic aromatic hydrocarbons (PAHs). Therefore, SPME using the AMTEOS/PDMS sol-gel fiber coupled with GC-FID was recommended as a sensitive and selective method towards the analysis of these compounds in environmental water samples. The optimal extraction conditions were investigated by adjusting extraction time, salt addition, extraction temperature, and desorption time. The method showed linearity between 2 and 4000 μg l⁻¹ for MAHs and 1 and 1000 μg l⁻¹ for PAHs. The limit of detection (LOD) was 0.6-3.8 μg l⁻¹for MAHs and 0.2-1.5 μg l⁻¹ for PAHs. The novel AMTEOS/PDMS fiber was applied to extract small amount of aromatic compounds in wastewater and river water respectively. The recovery of the method was acceptable for quantitative analysis.     

Multiple pesticide analysis in wine by MEKC combined with solid-phase microextraction and sample stacking

In this work, a new method for the determination in white wines of 12 pesticides widely used in vine cultivars (namely, carbendazim, pirimicarb, metalaxyl, pyrimethanil, procymidone, nuarimol, azoxystrobin, tebufenozide, fenarimol, benalaxyl, penconazole, and tetradifon) using solid-phase microextraction (SPME) and MEKC with diode-array detection (DAD) was developed. The MEKC buffer consisted of 100 mM sodium tetraborate and 30 mM SDS at pH 8.5 with 6% v/v 1-propanol. Reversed-electrode polarity stacking mode (REPSM) was applied as on-line preconcentration strategy. In order to carry out an effective and sensitive determination of these pesticides in wine samples, an off-line SPME procedure was optimized by means of an experimental design. After studying the extraction performance of different SPME coatings, PDMS/divinylbenzene (PDMS/DVB) fibers were found the most appropriate for the extraction of most of these pesticides. Carbendazim and metalaxyl could not be extracted from wine samples. Calibration curves for extracted standards and fortified white wines were studied in order to determine the presence of a matrix effect. The combination of both preconcentration procedures (SPME and REPSM) allowed the determination of ten of these pesticides in white wines at concentrations between 0.054 and 0.113 mg/L. (i.e., levels well below the maximum residue limits (MRLs) allowed for these compounds in wine grapes). Ten homemade wines were they analyzed with the optimized method demonstrating the usefulness of the proposed procedure.