电感耦合等离子体质谱法测定硫化物单矿物中痕量稀土元素

硫化物单矿物基体复杂,在利用电感耦合等离子体质谱仪测定其中稀土元素时,基体效应干扰严重,为准确测定其中的稀土元素,必须对样品进行分离富集。采用硝酸-氢氟酸体系溶解样品,通过Fe(OH)_3共沉淀和阴离子交换树脂(AG1-X8)去除基体元素,利用电感耦合等离子体质谱法测定稀土元素。通过测定两种国家标准物质硫化物单矿物(GBW 07267,GBW07268,GBW07270)中稀土元素来验证该方法,方法检出限为0. 003(Tm)～0. 138(Ce) ng·g~(-1),加标回收率在91%～113%之间。     

微波消解-电感耦合等离子体质谱法检测土壤中16种稀土元素

建立了微波消解-电感耦合等离子体质谱法(ICP-MS)测定土壤样品中16种稀土元素的分析方法。样品经硝酸-过氧化氢-氢氟酸消解,直接用ICP-MS测定试液中16种稀土元素。研究了ng/mL水平的Ba氧化物及轻稀土氧化物对重稀土元素的干扰程度,其中Ba和Pr的氧化物干扰较严重,不过此类干扰可通过Method编辑干扰方程得以校正。测定土壤标准物质GBW07446及GBW07451,结果与标准物质证书值一致。     

ICP-AES和ICP-MS法测定光学玻璃中的15种稀土元素

采用Na₂O₂熔融分解样品,运用电感耦合等离子体发射光谱法（ICP-AES）和电感耦合等离子体质谱法（ICP-MS）测定光学玻璃中的稀土元素。采用该方法对国家一级标准物质GBW07158、GBW07159、GBW07160和GBW07161进行测定,其结果表明与标准值相符。方法选择性好、灵敏度好、定量准确,适用于光学玻璃中稀土元素的测定,结果令人满意。     

微波消解-电感耦合等离子体质谱法测定地质样品中稀土元素

建立了微波消解-电感耦合等离子体质谱(ICP-MS)测定地质样品中稀土元素的方法,采用HNO3-HF体系-微波消解进行样品前处理,经赶酸后再用5 m L 1∶1 HNO3提取,整个过程安全、高效、无损失。利用ICP-MS进行测定,可以有效降低多原子离子质谱干扰,在优化仪器参数后,用内标铑(Rh)进行校正,弥补基体抑制效应和灵敏度漂移,测试结果更加准确。方法用于岩石标准物质(GBW07109,GBW07110和GBW07111)测试,其测定值与标准值相一致。结果表明,该方法的检出限低,准确度高,操作简单快捷,可同时测定多种元素,能满足批量测定地质样品中稀土元素含量的要求。     

茶叶中稀土元素的萃取分离-ICP-AES法测定

采用1-苯基-3-甲基-4-苯甲酰基-5-吡唑酮(PMBP)苯溶液萃取分离-ICP-AES法同时测定茶叶中15种稀土元素,消除了基体的干扰,并对样品前处理方法、萃取分离条件进行了考查.方法回收率为: 92.3%～112%,相对标准偏差＜2.5%.在最佳工作条件下,测定了茶叶标准物质(GBW07605)中稀土元素,结果与标准值吻合.     

微波消解-电感耦合等离子体质谱法同时测定食品中的主、微量元素

采用微波消解食品样品后直接进行分析,调节动态反应池DRC( Dynamic reaction cell)的电压参数( Rpa)而不通入气体,选择性抑制高浓度元素K,Na,Ca,Mg,Al的信号强度,同时应用DRC技术有效的消除了m/z 75处40 Ar35 Cl+对砷测定的干扰,建立了电感耦合等离子体质谱法同时测定食品中K,Na,Ca,Mg,Al, Cu,Zn,Pb,As,Mn共10种元素的分析方法。 K,Na,Ca,Mg,Al的检出限为0.013~0.027 mg/L; Cu,Pb,Zn, As,Mn的检出限为0.12~0.61μg/L。采用国家标准物质GBW10023(紫菜),GBW10015(菠菜),GBW10018(鸡肉),GBW10017(奶粉),GBW10019(苹果)和GBW10024(扇贝)进行方法验证,结果准确可信。本方法具有高通量,低成本,样品污染风险小的优点,能够对样品中高低含量的元素同时分析。     

一体化碰撞反应(iCRC)-电感耦合等离子体质谱(ICP-MS)法测定地质样品中痕量稀土元素

钡以及轻稀土元素氧化物对中、重稀土元素的干扰一直是质谱测试中存在的问题。建立了石墨粉垫底碳酸钠-硼酸混合熔剂熔融前处理样品,以103 Rh为内标校正,一体化碰撞反应-电感耦合等离子体质谱(ICP-MS)法测定地质样品中稀土元素含量的方法。探讨了碳酸钠-硼酸混合熔剂熔融前处理样品注意事项、碰撞模式下碰撞气流量和离子透镜的参数优化、干扰校正实验等问题,采用国家标准物质GBW07403、GBW07405、GBW07427、GBW07429验证,实验结果表明,各元素线性关系良好,相关系数均大于0.999,方法检出限在0.01～0.03mg/kg,相对误差为0.13%～7.1%,相对标准偏差为0.79%～6.6%,测定结果与标准值相吻合。对实际样品分析,得到平滑的球粒陨石归一化的稀土元素配分曲线,证明测定结果是合理可信的。方法熔剂用量少,过程空白低,对器皿的侵蚀小,直接加热浸取,简化了操作过程,适用于大批量地质样品中稀土元素的测定。     

微波消解ICP-MS快速测定生物样品中的多种元素

建立了微波辅助HNO3消解样品,ICP-MS快速测定生物样品中Ti、Cr、Mn、Fe、Co、Ni、Cu、Zn、Ge、As、Se、Sr、Mo、Ag、Cd、I、Ba、Hg、Tl、Pb、Bi共21种微量及痕量元素。通过在线加入内标来校正基体效应和信号漂移对测量所造成的影响。各元素线性相关系数在0.9990以上,RSD小于6.0%。用本方法对国家标准样品GBW07601a(头发),GBW10010(大米),GBW10016(茶叶),GBW10023(紫菜)进行分析,结果满意。方法能满足生物样品痕量分析的要求。     

银菊珍珠胶囊中稀土元素的电感耦合等离子体质谱分析

建立了一种电感耦合等离子体质谱法测定银菊珍珠胶囊中稀土元素的方法。利用该方法分析了国家一级灌木枝叶标准物质（GBW 07603）和国际柑橘叶标准物质（NIST1572）中的稀土元素,结果与标准值一致。该方法已被用于分析银菊珍珠肢囊样品中的稀土元素。     

湿法消解ICP-MS法测定紫菜和海带中15种元素

以HNO3-HClO4作为消解液,采用电热板湿法消解样品,ICP-MS法建立了同时测定紫菜和海带等高盐样品中As,Pb,Cd,Cr,Hg,Mn,Fe,Co,Ni,Cu,Zn,Se,Ag,Sr和Ba等15种元素的分析方法。通过优化仪器条件,选择带碰撞池的He模式和耐高盐(HMI)模式,避免了样品中盐分带来的双电荷干扰和基体效应等常见干扰。被测元素的检出限为4.0×10-3~0.283 ng/g,相对标准偏差(n=11)低于10%。方法经国家标准物质GBW10023(紫菜)验证,与标准值一致。方法适用于紫菜和海带等高盐样品的质量控制和安全风险评估。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.