Supported Pd-perovskite catalyst for CNG engines'' exhaust gas treatment

Perovskite-type oxides of the series La_1−xA_xMn_1−yB_yO₃ (A = Sr; B = Fe or Co) were prepared by solution combustion synthesis and characterized by X-ray diffraction, specific surface analysis, transmission electron microscopy and field emission scanning electron microscopy techniques. Their activity towards the combustion of methane was evaluated in a temperature programmed combustion microreactor. The LaMn_0.9Fe_0.1O₃ catalyst was found to provide the best performance. The half-conversion temperature of methane over the LaMn_0.9Fe_0.1O₃ catalyst was 398 °C with a W/F = 0.12 g s/cm³ and a methane feed concentration of 0.4 vol% under oxygen excess. Via temperature programmed oxygen desorption (TPD) analysis as well as catalytic combustion runs, the prevalent activity of the LaMn_0.9Fe_0.1O₃ catalyst could be explained by its higher and increased capability to desorb suprafacial, weakly chemisorbed oxygen species. Further catalyst development allowed to maximise the catalytic activity of this compound by promoting it with CeO₂ (1:1 molar ratio) and with 1 wt% Pd. This promoted catalyst was lined on cordierite monoliths in a γ-Al₂O₃-supported form (catalyst weight percentage: 15 wt%) and then tested in a lab-scale test rig under realistic conditions for compressed natural gas-vehicles' exhaust gas treatment. Half methane conversion was achieved at 340 °C (gas high space velocity = 10 000 h⁻¹), nearly the same but with a fourfold lower amount of the expensive noble metal than that used in commercial 4wt%Pd–γ-Al₂O₃ catalysts.     

Thermal stability and related thermodynamic properties of N-ethylthiourea

The enthalpy and entropy of sublimation of N-ethylthiourea were obtained from the temperature dependence of its vapour pressure measured by both the torsion–effusion and the Knudsen effusion method in the temperature range 360–380 K. The compound undergoes no solid-to-solid phase transition or decomposition below 380 K. The pressure against reciprocal temperature resulted in lg(p, kPa) = (13.40 ± 0.27) − (6067 ± 102) /T(K). The molar sublimation enthalpy and entropy at the mid interval temperature were Δ_subH_m(370 K) = (116.1 ± 2.0) kJ mol⁻¹ and Δ_subS_m(370 K) = (218.0 ± 5.2) J mol⁻¹ K⁻¹, respectively. The same quantities derived at 298.15 K were (118.8 ± 2.1) kJ mol⁻¹ and (226.1 ± 5.5) J mol⁻¹ K⁻¹, respectively.     

Kinetics study of the gas-phase reactions of C2F5OC(O)H and n-C3F7OC(O)H with OH radicals at 253–328 K

The rate constants, k₁ and k₂ for the reactions of C₂F₅OC(O)H and n-C₃F₇OC(O)H with OH radicals were measured using an FT-IR technique at 253–328 K. k₁ and k₂ were determined as (9.24 ± 1.33) × 10⁻¹³ exp[−(1230 ± 40)/T] and (1.41 ± 0.26) × 10⁻¹² exp[−(1260 ± 50)/T] cm³ molecule⁻¹ s⁻¹. The random errors reported are ±2 σ, and potential systematic errors of 10% could add to the k₁ and k₂. The atmospheric lifetimes of C₂F₅OC(O)H and n-C₃F₇OC(O)H with respect to reaction with OH radicals were estimated at 3.6 and 2.6 years, respectively.     

Determination of cilnidipine, a new calcium antagonist, in human plasma using high performance liquid chromatography with tandem mass spectrometric detection

A rapid, sensitive and reliable high performance liquid chromatographic method coupled with tandem mass spectrometry (HPLC–MS/MS) has been developed and validated for the determination of cilnidipine, a relatively new calcium antagonist, in human plasma. The reversed-phase chromatographic system was interfaced with a TurboIonSpray (TIS) source. Nimodipine was employed as the internal standard (IS). Sample extracts following protein precipitation were injected into the HPLC–MS/MS system. The analyte and IS were eluted isocratically on a C18 column, with a mobile phase consisting of CH₃OH and NH₄Ac (96:4, v/v). The ions were detected by a triple quadrupole mass spectrometric detector in the negative mode. Quantification was performed using multiple reaction monitoring (MRM) of the transitions m/z 491.2 → 122.1 and m/z 417.1 → 122.1 for cilnidipine and for the IS, respectively. The analysis time for each run was 3.0 min. The calibration curve fitted well over the concentration range of 0.1–10 ng mL⁻¹, with the regression equation Y = (0.103 ± 0.002)X + (0.014 ± 0.003) (n = 5), r = 0.9994. The intra-day and inter-day R.S.D.% were less than 12.51% at all concentration levels within the calibration range. The recoveries were between 92.71% and 97.64%. The long-term stability and freeze-thaw stability were satisfying at each level. The present method provides a modern, rapid and robust tool for pharmacokinetic studies of cilnidipine.     

Interaction between Pd and Ag on the surface of silica

Palladium, silver and palladium–silver catalysts supported on silica were prepared by coimpregnation of support with solution of AgNO₃ and Pd(NO₃)₂. The catalysts were characterized by X-ray powder diffraction (XRD), temperature programmed reduction (TPR), time of flight ion mass spectrometry (ToF-SIMS), chemisorption of carbon monoxide and were tested in the reaction of selective oxidation of glucose to gluconic acid.

XRD and TPR studies have shown that an interaction between Pd and Ag on the surface of silica after oxidation at 500 °C and reduction at 260 °C leads to the formation of solid solutions.

ToF-SIMS images of the surface of 5% Ag/SiO₂ catalyst after oxidation at 500 °C and reduction at 260 °C show that Ag atoms supported on silica are not distributed homogenously but tend to form regions of enhanced Ag concentration. Positive ions images of the surface of 5% Pd/SiO₂ catalyst also display regions of enhanced concentration of Pd atoms, but they are more homogenously distributed on silica.

ToF-SIMS peak intensity ratio ¹⁰⁸Pd⁺/¹⁰⁷Ag⁺ for bimetallic 5% Pd–5% Ag/SiO₂ catalysts has a lower value than that obtained for physical mixture 5% Pd/SiO₂–5% Ag/SiO₂ which indicates that the surface of bimetallic catalyst is enriched with silver atoms.     

CeO2负载的PdO与Ce1‒x Pd x O2‒δ 物种的甲烷催化燃烧性能

通过调控Pd前驱物在CeO₂上的沉积方式, 分别制备了以PdO和离子态的Ce_1?x Pd _x O_2?δ 物种为主的 Pd/CeO₂催化剂, 并采用X射线光电子能谱(XPS)和拉曼(Raman)光谱确证了这两种Pd物种的存在. 氧气程序升温脱附(O₂-TPD)和氢气程序升温还原(H₂-TPR)的表征结果显示, 相比于与载体相互作用较弱的PdO物种, 与CeO₂相互作用较强的Ce_1?x Pd _x O_2?δ 物种具有更加稳定的Pd—O键. 催化剂的甲烷燃烧反应起燃活性测试结果显示, 以PdO物种为主的催化剂表现出了良好的低温催化性能, 在原料气配比为1%CH₄/4%O₂-Ar, 空速为60000 mL·{\mathrm{g}}_{\mathrm{c}\mathrm{a}\mathrm{t}}^{-\mathrm{1}}·h^?1的条件下, T₁₀和T₉₀分别为275和367 ℃, 而两种以Ce_1?x Pd _x O_2?δ 物种为主的催化剂的T₁₀均超过420 ℃. 催化剂的甲烷程序升温还原(CH₄-TPR)表征结果表明, 在升温过程中只有当PdO或Ce_1?x Pd _x O_2?δ 物种被CH₄还原后, 催化活性才开始上升. 由于PdO物种的Pd—O键强度较弱, 有利于Pd物种上的晶格氧在较低温度下参与CH₄的氧化过程. 而Ce_1?x Pd _x O_2?δ 物种的Pd—O键较稳定, 且在反应条件下离子态Pd²⁺与反应体系中氧物种的作用较强, 进而抑制了其与CH₄的反应, 因此反应的起燃温度较高. 以γ-Al₂O₃为载体采用相同的方法制备了Pd/γ-Al₂O₃催化剂, 相关的表征结果进一步证实, 与载体相互作用较弱的PdO物种更容易被CH₄还原, 进而具有较高的催化活性. 据此可以认为Pd/CeO₂上氧化态的Pd物种被CH₄的还原性能是决定其甲烷催化燃烧反应活性的重要因素之一.     

Membrane reactor performance of steam reforming of methane using hydrogen-permselective catalytic SiO2 membranes

Hydrogen production by steam reforming of methane using catalytic membrane reactors was investigated first by simulation, then by experimentation. The membrane reactor simulation, using an isothermal and plug-flow model with selective permeation from reactant stream to permeate stream, was conducted to evaluate the effect of permselectivity on membrane reactor performance – such as methane conversion and hydrogen yield – at pressures as high as 1000 kPa. The simulation study, with a target for methane conversion of 0.8, showed that hydrogen yield and production rate have approximately the same dependency on operating conditions, such as reaction pressure, if the permeance ratio of hydrogen over nitrogen ((H₂/N₂)) is larger than 100 and of H₂ over H₂O is larger than 15. Catalytic membrane reactors, consisting of a microporous Ni-doped SiO₂ top layer and a catalytic support, were prepared and applied experimentally for steam reforming of methane at 500 °C. A bimodal catalytic support, which allows large diffusivity and high dispersion of the metal catalyst, was prepared for the enhancement of membrane catalytic activity. Catalytic membranes having H₂ permeances in the range of 2–5 × 10⁻⁶ m³ m⁻² s⁻¹ kPa⁻¹, with H₂/N₂ of 25–500 and H₂/H₂O of 6–15, were examined for steam reforming of methane. Increased performance for the production of hydrogen was experimentally obtained with an increase in reaction-side pressure (as high as 500 kPa), which agreed with the theoretical simulation with no fitting parameters.     

Infrared and Raman spectra, conformational stability, ab initio calculations, and vibrational assignments for methylaminothiophosphoryl difluoride

Infrared spectra (4000–50 cm⁻¹) of the vapor, amorphous and crystalline solids and Raman spectra (3600–10 cm⁻¹) of the liquid with qualitative depolarization data as well as the amorphous and crystalline solids of methylaminothiophosphoryl difluoride, CH₃N(H)P(=S)F₂, and three deuterated species, CD₃N(H)P(=S)F₂, CH₃N(D)P(=S)F₂, and CD₃N(D)P(=S)F₂, have been recorded. The spectra indicate that in the vapor, liquid and amorphous solid a small amount of a second conformer is present, whereas only one conformer remains in the low temperature crystalline phase. The near-infrared spectra of the vapor confirms the existence of two conformers in the gas phase. Asymmetric top contour simulation of the vapor shows that the trans conformer is the predominant vapor phase conformer. From a temperature study of the Raman spectrum of the liquid the enthalpy difference between the trans and near-cis conformers was determined to be 368±15 cm⁻¹ (4.41±0.2 kJ/mol), with the trans conformer being thermodynamically preferred. Ab Initio calculations with structure optimization using the 6-31G(d) and 6-311+G(d,p) basis sets at the restricted Hartree–Fock (RHF) and/or with full electron correlation by the perturbation method to second order (MP2) support the occurrence of near-trans (5° from trans) and near-cis (20° from cis) conformers. From the RHF/6-31G(d) calculation the near-trans conformer is predicted to be the more stable form by 451 cm⁻¹ (5.35 kJ/mol) and from the MP2/6-311+G(d,p) calculation by 387 cm⁻¹ (4.63 kJ/mol). All of the normal modes of the near-trans rotamer have been assigned based on infrared band contours, depolarization values and group frequencies and the assignment is supported by the normal coordinate calculation utilizing harmonic force constants from the MP2/6-31G(d) ab initio calculations.     

Sub-picomole high-performance liquid chromatographic/mass spectrometric determination of glutathione in the maize (Zea mays L.) kernels exposed to cadmium

Changes in fresh weight, total protein amounts (Bradford’s method), cadmium concentration (DPASV) and glutathione content (HPLC/MS) were studied in maize kernels cultivated for 5 days at three different cadmium concentrations (0, 10 and 100 μmol l⁻¹ CdCl₂). A highly sensitive HPLC/MS method was used for the determination of glutathione on a reversed-phase Atlantis dC₁₈ chromatographic column (150 mm×2.1 mm, 3 μm particle size). An isocratic mode with acetonitrile–0.01% TFA (5:95, flow rate 0.1 ml min⁻¹ and 30 °C) was applied. The m/z spectra and the data for the selected ion monitoring (SIM) mode were recorded at m/z for glutathione 308→179. Cadmium concentration was measured by a differential pulse adsorptive stripping voltammetry (DPASV) after deposition on a hanging mercury drop electrode (HMDE) at potential −0.7 V (accumulation time 180 s, acetate buffer of pH 3.6, 22 °C). An AUTOLAB with a VA-Stand 663 and a three-electrode system consisting of the HMDE as a working electrode with area 0.4 mm², an Ag/AgCl/3 mol l⁻¹ KCl as a reference electrode and a Pt-wire as an auxiliary electrode was employed. The maize kernels exposed to the highest cadmium concentration (100 μmol l⁻¹) germinated formerly and much better. A rapid increase of the fresh weight probably relates with more intensive uptake of water in order to decrease cadmium concentration. An intensive preservation of homeostasis of Cd²⁺ ions in the germinating plants by defending mechanisms might explain differences of uptake rate of cadmium. The linear increase of GSH content with the exposure time at all studied concentration suggests the defending mechanisms might be triggered by concentrations of a heavy metal.     

Determination of perfluorooctanesulfonate and perfluorooctanoic acid in sewage sludge samples using liquid chromatography/quadrupole time-of-flight mass spectrometry

A new method is developed for the determination of perfluorooctanesulfonate (PFOS) and perfluorooctanoic acid (PFOA) in sewage sludge samples. The analytes in sewage sludge samples are extracted by methanol and formic acid, cleaned by C18 solid-phase extraction, then separated, identified and quantitated by liquid chromatography/quadrupole time-of-flight mass spectrometry (LC–QTOF-MS). A C18 column (150 mm × 2.1 mm, 3.5 μm) with gradient elution of MeOH–H₂O (60:40) containing 5 mmol/L ammonium acetate and MeOH–H₂O (80:20) is used for the chromatographic separation. [M−K]⁻ ions at m/z 498.93 for PFOS and [M−COOH]⁻ ion at m/z 368.97 for PFOA are selected for QTOF-MS in the negative electrospray ionization mode. The detection limits for PFOS and PFOA in sewage sludge samples are 0.5 and 0.8 ng/g, respectively. The spiked recoveries are in the range of 85–114 and 71–98% for PFOS and PFOA, respectively. The proposed method is successfully applied to the analysis of PFOS and PFOA in 16 sewage sludge samples from China. PFOS and PFOA are detected in most sewage sludge samples and the concentrations of PFOS and PFOA are up to 5383 and 4780 ng/g (oven dry weight), respectively.     

Analysis of acrylamide in coffee and dietary exposure to acrylamide from coffee

An analytical method for analysing acrylamide in coffee was validated. The analysis of prepared coffee includes a comprehensive clean-up using multimode solid-phase extraction (SPE) by automatic SPE equipment and detection by liquid chromatography tandem mass spectrometry using electrospray in the positive mode. The recoveries of acrylamide in ready-to-drink coffee spiked with 5 and 10 μg l⁻¹ were 96±14% and 100±8%, respectively. Within laboratory reproducibility for the same spiking levels were 14% and 9%, respectively. Coffee samples (n = 25) prepared twice by coffee machines and twice by a French Press Cafetière coffee maker contained 8±3 μg l⁻¹ and 9±3 μg l⁻¹ acrylamide. Five ready-to-drink instant coffee prepared twice contained 8±2 μg l⁻¹. Hence, the results do not show significant differences in the acrylamide contents in ready-to-drink coffee prepared by coffee machine, French Press or from instant coffee. Medium roasted coffee contained more acrylamide (10 μg l⁻¹) than dark roasted coffee (5 μg l⁻¹). Males aged 35–45 years, drinking on average 1.1 l coffee per day are exposed to the highest doses of acrylamide from coffee. The dietary intake of acrylamide from coffee comprises, on an average, 10 μg day⁻¹ for males and 9 μg day⁻¹ for females aged 35–45 years. Probabilistic modelling of the exposure of Danish consumers (all adults) to acrylamide from coffee shows a mean exposure of 6.5 μg day⁻¹ and a 95 percentile of 18 μg day⁻¹.     

Far infrared spectra, conformational equilibria, vibrational assignments, ab initio calculations and structural parameters for 2-bromoethanol

The far infrared spectrum from 370 to 50 cm⁻¹ of gaseous 2-bromoethanol, BrCH₂CH₂OH, was recorded at a resolution of 0.10 cm⁻¹. The fundamental O–H torsion of the more stable gauche (Gg′) conformer, where the capital G refers to internal rotation around the C–C bond and the lower case g to the internal rotation around the C–O bond, was observed as a series of Q-branch transitions beginning at 340 cm⁻¹. The corresponding O–H torsional modes were observed for two of the other high energy conformers, Tg (285 cm⁻¹) and Tt (234 cm⁻¹). The heavy atom asymmetric torsion (rotation around C–C bond) for the Gg′ conformer has been observed at 140 cm⁻¹. Variable temperature (−63 to −100°C) studies of the infrared spectra (4000–400 cm⁻¹) of the sample dissolved in liquid xenon have been recorded. From these data the enthalpy differences have been determined to be 411±40 cm⁻¹ (4.92±0.48 kJ/mol) for the Gg′/Tt and 315±40 cm⁻¹ (3.76±0.48 kJ/mol) for the Gg′/Tg, with the Gg′ conformer the most stable form. Additionally, the infrared spectrum of the gas, and Raman spectrum of the liquid phase are reported. The structural parameters, conformational stabilities, barriers to internal rotation and fundamental frequencies have been obtained from ab initio calculations utilizing different basis sets at the restricted Hartree–Fock or with full electron correlation by the perturbation method to second order. The theoretical results are compared to the experimental results when appropriate. Combining the ab initio calculations with the microwave rotational constants, r₀ adjusted parameters have been obtained for the three 2-haloethanols (F, Cl and Br) for the Gg′ conformers.     

Optimisation of sample treatment for arsenic speciation in alga samples by focussed sonication and ultrafiltration

A procedure for arsenic species fractionation in alga samples (Sargassum fulvellum, Chlorella vulgaris, Hizikia fusiformis and Laminaria digitata) by extraction is described. Several parameters were tested in order to evaluate the extraction efficiency of the process: extraction medium, nature and concentration (tris(hydroxymethyl)aminomethane, phosphoric acid, deionised water and water/methanol mixtures), extraction time and physical treatment (magnetic stirring, ultrasonic bath and ultrasonic focussed probe). The extraction yield of arsenic under the different conditions was evaluated by determining the total arsenic content in the extracts by ICP-AES. Arsenic compounds were extracted in 5 mL of water by focussed sonication for 30 s and subsequent centrifugation at 14,000 × g for 10 min. The process was repeated three times. Extraction studies show that soluble arsenic compounds account for about 65% of total arsenic.

An ultrafiltration process was used as a clean-up method for chromatographic analysis, and also allowed us to determine the extracted arsenic fraction with a molecular weight lower than 10 kDa, which accounts for about 100% for all samples analysed.

Speciation studies were carried out by HPLC–ICP-AES. Arsenic species were separated on a Hamilton PRP-X100 column with 17 mM phosphate buffer at pH 5.5 and 1.0 mL min⁻¹ flow rate. The chromatographic method allowed us to separate the species As(III), As(V), MMA and DMA in less than 13 min, with detection limits of about 20 ng of arsenic per species, for a sample injection volume of 100 μL. The chromatographic analysis allowed us to identify As(V) in Hizikia (46 ± 2 μg g⁻¹), Sargassum (38 ± 2 μg g⁻¹) and Chlorella (9 ± 1 μg g⁻¹) samples. The species DMA was also found in Chlorella alga (13 ± 1 μg g⁻¹). However, in Laminaria alga only an unknown arsenic species was detected, which eluted in the dead volume.     

Structure and conformational properties of carbonylbisimidosulfuryl fluoride, O=C(N=S(O)F2)2

The molecular structure and conformational properties of O=C(N=S(O)F₂)₂ (carbonylbisimidosulfuryl fluoride) were determined by gas electron diffraction (GED) and quantumchemical calculations (HF/3-21G* and B3LYP/6-31G*). The analysis of the GED intensities resulted in a mixture of 76(12)% syn–syn and 24(12)% syn–anti conformer (ΔH⁰=H⁰(syn–anti)−H⁰(syn–syn)=1.11(32) kcal mol⁻¹) which is in agreement with the interpretation of the IR spectra (68(5)% syn–syn and 32(5)% syn–anti, ΔH⁰=0.87(11) kcal mol⁻¹). syn and anti describe the orientation of the S=N bonds relative to the C=O bond. In both conformers the S=O bonds of the two N=S(O)F₂ groups are trans to the C–N bonds. According to the theoretical calculations, structures with cis orientation of an S=O bond with respect to a C–N bond do not correspond to minima on the energy hyperface. The HF/3-21G* approximation predicts preference of the syn–anti structure (ΔE=−0.11 kcal mol⁻¹) and the B3LYP/6-31G* method results in an energy difference (ΔE=1.85 kcal mol⁻¹) which is slightly larger than the experimental values. The following geometric parameters for the O=C(N=S)₂ skeleton were derived (r_a values with 3σ uncertainties): C=O 1.193 (9) Å, C–N 1.365 (9) Å, S=N 1.466 (5) Å, O=C–N 125.1 (6)° and C–N=S 125.3 (10)°. The geometric parameters are reproduced satisfactorily by the HF/3-21G* approximation, except for the C–N=S angle which is too large by ca. 6°. The B3LYP method predicts all bonds to be too long by 0.02–0.05 Å and the C–N=S angle to be too small by ca. 4°.     

Effects of the addition of titania on the thermal characterization of alumina-supported palladium

The detailed thermal characterization of Pd/TiO₂–Al₂O₃ catalysts under oxygen and hydrogen atmosphere was conducted by means of thermal gravimetric analysis/differential scanning calorimetry (TG/DSC), temperature-programmed reduction (TPR) and temperature-programmed desorption (TPD). A simultaneous TG/DSC measurement revealed that the heat evolved during oxygen adsorption at 25 °C varied slightly with the supports and had a higher value for the smaller palladium crystallite. Hydrogen chemisorption and BET measurements revealed that the coating of Pd/Al₂O₃ catalysts with titania modified the support character to achieve a high dispersion of palladium. TPR and TPD characterizations of oxidized samples further demonstrated that the coating of Pd/Al₂O₃ catalysts with titania promoted the reduction and decomposition of PdO into palladium.     

Interaction of Pseudomonas putida with kaolinite and montmorillonite: a combination study by equilibrium adsorption, ITC, SEM and FTIR

Equilibrium adsorption along with isothermal titration calorimetry (ITC), Fourier transform infrared spectra (FTIR) and scanning electron microscopy (SEM) techniques were employed to investigate the adsorption of Pseudomonas putida on kaolinite and montmorillonite. A higher affinity as well as larger amounts of adsorption of P. putida was found on kaolinite. The majority of sorbed bacterial cells (88.7%) could be released by water from montmorillonite, while only a small proportion (9.3%) of bacteria desorbed from kaolinite surface. More bacterial cells were observed to form aggregates with kaolinite, while fewer cells were within the larger bacteria–montmorillonite particles. The sorption of bacteria on kaolinite was enthalpically more favorable than that on montmorillonite. Based on our findings, it is proposed that the non-electrostatic forces other than electrostatic force play a more important role in bacterial adsorption by kaolinite and montmorillonite. Adsorption of bacteria on clay minerals resulted in obvious shifts of infrared absorption bands of water molecules, showing the importance of hydrogen bonding in bacteria–clay mineral adsorption. The enthalpies of −4.1 ± 2.1 × 10⁻⁸ and −2.5 ± 1.4 × 10⁻⁸ mJ cell⁻¹ for the adsorption of bacteria on kaolinite and montmorillonite, respectively, at 25 °C and pH 7.0 were firstly reported in this paper. The enthalpy of bacteria–mineral adsorption was higher than that reported previously for bacteria–biomolecule interaction but lower than that of bacterial coaggregation. The bacteria–mineral adsorption enthalpies increased at higher temperature, suggesting that the enthalpy–entropy compensation mechanism could be involved in the adsorption of P. putida on clay minerals. Data obtained in this study would provide valuable information for a better understanding of the mechanisms of mineral–microorganism interactions in soil and associated environments.     

Infrared and Raman spectra, conformational stability, ab initio calculations of structure, and vibrational assignment of 2-hexyne

The infrared spectra (3500–50 cm⁻¹) of the gas and solid and the Raman spectra (3500–50 cm⁻¹) of the liquid and solid have been recorded for 2-hexyne, CH₃–CC–CH₂CH₂CH₃. Variable temperature studies of the infrared spectrum (3500–400 cm⁻¹) of 2-hexyne dissolved in liquid krypton have also been recorded. Utilizing four anti/gauche conformer pairs, the anti(trans) conformer is found to be the lower energy form with an enthalpy difference of 74±8 cm⁻¹ (0.88±0.10 kJ/mol) determined from krypton solutions over the temperature range −105 to −150 °C. At room temperature it is estimated that there is 42% of the anti conformer present. Equilibrium geometries and energies of the two conformers have been determined by ab initio (HF and MP2) and hybrid DFT (B3LYP) methods using a number of basis sets. Only the HF and DFT methods predict the anti conformer as the more stable form as found experimentally. A vibrational assignment is proposed based on the force constants, relative intensities, depolarization ratios from the ab initio and DFT calculations and on rotational band contours obtained using the calculated equilibrium geometries. From calculated energies it is shown that the CH₃ group exhibits almost completely free rotation which is in agreement with the observation of sub-band structure for the degenerate methyl vibrations from which values of the Coriolis coupling constants, ζ, have been determined. The results are compared to similar properties of some corresponding molecules.     

Raman and infrared spectra, conformational stability, ab initio calculations and vibrational assignments for 2-chloroethyl silane

The infrared (3500–30 cm⁻¹) spectra of gaseous and solid and the Raman (3500–10 cm⁻¹) spectra of liquid with quantitative depolarization ratios and solid 2-chloroethyl silane, ClCH₂CH₂SiH₃, have been recorded. Similar data have been recorded for the Si–d₃ isotopomer. These data indicate that two conformers, trans and gauche, are present in the fluid states but only one conformer, trans, is present in the solid. The mid-infrared spectra of the sample dissolved in liquified xenon as a function of temperature (−55 to −100°C) has been recorded. The enthalpy difference between the conformers has been determined to be 181±12 cm⁻¹ (2.17±0.14 kJ/mol) with the trans rotamer the more stable form. From the isolated Si–H frequencies from the Si–d₂ isotopomer the r_o Si–H distances of 1.484 and 1.483 Å for the trans and 1.481 for the gauche conformers have been obtained. Ab initio calculations have been carried out with several different basis sets up to MP2/6-311+G** from which structural parameters and conformational stabilities have been determined. With all the basis sets the trans form is predicted to be the more stable conformer which is consistent with the experimental results. These results are compared to the corresponding quantities for the carbon analogue.     

Preparation of novel ion exchange polyurethane foam and its application for separation and determination of palladium in environmental samples

The new strong anion exchanger (PUFIX) from polyurethane foam was prepared by coupling of the primary amine of the foam matrix with ethyl iodide. PUFIX was characterized using different tools (IR spectra, elemental analysis, density and thermal analysis). The sorption properties of the new anion exchanger (PUFIX) and chromatographic behaviour for separation and determination of palladium(II) ions at low concentrations from aqueous iodide or thiocyanate media were investigated by a batch and dynamic processes. The maximum sorption of Pd(II) was in the pH range of 0.3–2. The kinetics of sorption of the Pd(II) by the PUFIX was found to be fast with average values of half-life of sorption (t_1/2) of 3.32 min. The variation of the sorption of Pd(II) with temperature gives average values of ΔH, ΔS, ΔG and ΔE to be −38.3 kJ mol⁻¹, −100.7 J K⁻¹ mol⁻¹, −8.3 and 11.8 kJ mol⁻¹, respectively. The sorption capacity of PUFIX was 1.69 mmol g⁻¹ for Pd(II), preconcentration factors of values ≈250 and the recovery 99–100% were achieved (R.S.D. ≈ 1.24%). The lower detection limit, 1.28 ng mL⁻¹ was evaluated using spectrophotometric method (R.S.D. ≈ 2.46%).     

Conformational studies of cyclopropylmethyl isocyanate from temperature dependent FT-IR spectra of xenon solutions and ab initio calculations

Variable temperature (−55 to −100 °C) studies of the infrared spectra (3200 to 100 cm⁻¹) of cyclopropylmethyl isocyanate, c-C₃H₅CH₂NCO, dissolved in liquefied xenon, have been carried out. The infrared spectra (gas and solid) as well as the Raman spectrum of the liquid have been recorded from 3200 to 100 cm⁻¹. By analyzing six conformer pairs in xenon solutions, an enthalpy difference of 193 ± 19 cm⁻¹ (2.31 ± 0.23 kJ/mol) was obtained with the gauche–cis rotamer (the first designation indicates the orientation of the CNCO group with respect to the three-membered ring, the second designation indicates the relative orientation of the NCO group with respect to the bridging CC bond) the more stable form and the only form present in polycrystalline solid. The abundance of the cis–trans conformer present at ambient temperature is 16 ± 1%. The potential function governing the conformational interchange has been obtained from B3LYP/6-31G(d) calculations and the two-dimensional potential has been obtained. From MP2 ab initio calculations utilizing various basis sets with diffuse functions, the gauche–cis conformer is predicted to be more stable by 223 to 269 cm⁻¹, which is consistent with the experimental results. However, without diffuse functions the predicted conformational energy differences are much smaller (77–166 cm⁻¹). Similar diffuse function dependency affects density functional theory calculations by the B3LYP method to a lesser extent. A complete vibrational assignment for the gauche–cis conformer is proposed and several fundamentals for the cis–trans conformer have been identified. The structural parameters, dipole moments, conformational stability, vibrational frequencies, infrared intensities and Raman activities have been predicted from ab initio calculations and r₀ structural parameters are estimated. These experimental and theoretical results are compared to the corresponding quantities of some similar molecules.